Fourier transform infrared/attenuated total reflectance analysis of water diffusion in poly[styrene‐b‐isobutylene‐ b‐styrene] block copolymer membranes

A Fourier transform infrared/attenuated total reflectance technique was used to study the diffusion of water through poly(styrene‐b‐isobutylene‐b‐styrene) block copolymers (BCPs), as well as sulfonated (H⁺) and Na⁺‐sulfonated ionomer versions. Diffusion data were collected and interpreted for these membranes versus polystyrene block composition, degree of sulfonation, Na⁺ ion content in the ionomers, and the effect of initially dry versus prehydrated conditions. An “early time” diffusion coefficient, D, decreased with increasing percent polystyrene for a series of unmodified BCPs. D decreased with increasing degree of sulfonation, and with increasing ion content for the Na⁺‐exchanged samples and this was interpreted in terms of diffusion limitations caused by a strong tendency for ion hydration. The method also yielded information relating to the time evolution of water structure from the standpoint of degree of intermolecular hydrogen bonding. Membrane prehydration causes profound increases in D for both the unmodified BCP and sulfonated samples, as in plasticization. The simultaneous acquisition of information relating to interactions between water molecules and interactions of water molecules with functional groups on the host polymer matrix offers more information than conventional diffusion measurement techniques that simply count transported molecules. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 764–776, 2005     

Sulfonated poly(meta‐phenylene isophthalamide)s as proton exchange membranes

Random and block sulfonated poly(meta‐phenylene isopthalamide)s as proton exchange membranes were synthesized through the Higashi‐Yamazaki phosphorylation method. Polymers with different degrees of sulfonation from 40 to 100 mol percent were prepared by adjusting the molar feed ratio of 5‐sulfoisophthalic acid sodium salt (SIPA) and isophthalic acid (IPA) in the reaction with meta‐phenylene diamine. Creasable polymer films were obtained by casting DMSO polymer solutions and the membrane films could be exchanged to the proton form in strong acid. ¹H NMR spectroscopy and titration confirmed the degree of sulfonation. Thermogravimetric analysis demonstrated good thermal stabilities with 5% weight loss greater than 380 °C. The copolymers with low degrees of sulfonation (DS = 40 mol %) exhibited low water uptake (water uptake < 17 wt %) at room temperature. A segmented multiblock copolymer prepared by preforming a sulfonated block showed lower water uptake at high temperatures than the random polymer with the same DS of 40 mol % and displayed stability in water up to 80 °C. Both random and block copolymers showed higher proton conductivities at high temperature than that of Nafion‐117 under 95% relative humidity. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2582–2592     

Synthesis of sulfonated poly(imidoaryl ether sulfone) membranes for polymer electrolyte membrane fuel cells

New sulfonated poly(imidoaryl ether sulfone) copolymers derived from sulfonated 4,4′‐dichlorodiphenyl sulfone, 4,4′‐dichlorodiphenyl sulfone, and imidoaryl biphenol were evaluated as polymer electrolyte membranes for direct methanol fuel cells. The sulfonated membranes were characterized with Fourier transform infrared spectroscopy, thermogravimetric analysis, and proton nuclear magnetic resonance spectra. The state of water in the membranes was measured with differential scanning calorimetry, and the existence of free water and bound water was discussed in terms of the sulfonation level. The 10 wt % weight loss temperatures of these copolymers were above 470 °C, indicating excellent thermooxidative stability to meet the severe criteria of harsh fuel‐cell conditions. The proton conductivities of the membranes ranged from 3.8 × 10^?2 to 5 × 10^?2 S/cm at 90 °C, depending on the degree of sulfonation. The sulfonated membranes maintained the original proton conductivity even after a boiling water test, and this indicated the excellent hydrolytic stability of the membranes. The methanol permeabilities ranged from 1.65 × 10^?8 to 5.14 × 10^?8 cm²/s and were lower than those of other conventional sulfonated ionomer membranes, particularly commercial perfluorinated sulfonated ionomer (Nafion). The properties of proton and methanol transport were discussed with respect to the state of water in the membranes. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5620–5631, 2005     

Synthesis and properties of sulfonated poly(arylene ether) containing tetraphenylmethane moieties for proton‐exchange membrane

A novel sulfonated poly(arylene ether) containing tetraphenylmethane moieties was successfully synthesized by the sulfonation of a designed parent polymer using chlorosulfonic acid as sulfonation agent. The sulfonation took place only at the para position on the pendant phenyl rings because of the specially designed parent polymer. The sulfonation degree can be easily controlled by using different ratios of sulfonation agent to polymer repeating unit. The position and degree of sulfonation were characterized by ¹H NMR and elemental analysis. The sulfonated polymers are highly soluble in common organic solvents, such as dimethylsulfoxide, N,N′‐dimethylacetamide, dimethylformamide, ethylene glycol monomethyl ether, and can be readily cast into tough and smooth films from solutions. The films showed good thermal and hydrolysis stabilities. Moreover, Fenton's reagent test revealed that the membrane exhibited superior stability to oxidation. The proton conductivities of the films were determined to be equivalent with Nafion® 117 under same conditions. The new polymer with sulfonic acid function on pendent phenyl rings can be potentially used as a proton‐exchange membrane for polymer electrolyte membrane fuel cell. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6411–6418, 2005     

Synthesis of sulfonated poly(diphenylacetylene)s with high CO2 permselectivity

High‐molecular‐weight poly[1‐phenyl‐2‐(4‐t‐butylphenyl)acetylene], poly[1‐phenyl‐2‐(4‐trimethylsilylphenyl) acetylene], and their copolymers were synthesized by the polymerization with TaCl₅–n‐Bu₄Sn. The obtained polymers were sulfonated by using acetyl sulfate to give sulfonated poly(diphenylacetylene)s with different degrees of substitution. The degrees of sulfonation of poly[1‐phenyl‐2‐(4‐t‐butylphenyl)acetylene] and copolymers were in the range of 0.57–0.85. When poly[1‐phenyl‐2‐(4‐trimethylsilylphenyl)acetylene] was sulfonated, the sulfonated poly(diphenylacetylene) with the highest degree of sulfonation was obtained among all the polymers in this study. Its degree of sulfonation was 1.55. All the sulfonated polymers exhibited high CO₂ permselectivity, and their CO₂/N₂ separation factor were over 31. The sulfonated poly(diphenylacetylene) with the highest degree of sulfonation showed the highest CO₂/N₂ separation factor of 75. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6463–6471, 2009     

Sulfonated polyimides containing 1,2,4-triazole groups for proton exchange membranes

A series of sulfonated polyimide copolymers as novel proton exchange materials were synthesized by the polycondensation of 1,4,5,8-naphthalene-tetracarboxylic dianhydride(NTDA), sulfonated diamine based on pyridine group and diamine containing N-phenyl-1,2,4-triazole moiety. Flexible, transparent and tough membranes with high thermal stability and good mechanical properties were obtained. They exhibited good stability in boiling water and Fenton's reagent at 80 °C. More interestingly, a nonlinear relationship between proton conductivities of the resulting membranes and the degree of sulfonation(DS) was observed. The membrane with 50% DS exhibited the maximum proton conductivity, which was due to the combinational contributions of sulfonic acid and N-pheny-1,2,4-triazole groups. Thus, the N-phenyl-1,2,4-triazole moiety in this study not only can depress water absorption but also increase proton conductivity, especially at low DS.     

Characterization and evaluation of commercial poly (vinylidene fluoride)‐g‐sulfonatedPolystyrene as proton exchange membrane

The possibility of developing low‐cost commercial grafted and sulfonated Poly(vinylidene fluoride) (PVDF‐g‐PSSA) membranes as proton exchange membranes for fuel cell applications have been investigated. PVDF‐g‐PSSA membranes were systematically prepared and examined with the focus of understanding how the polymer microstructure (degree of grafting and sulfonation, ion‐exchange capacity, etc) affects their methanol permeability, water uptake, and proton conductivity. Fourier transform infrared spectroscopy was used to characterize the changes of the membrane's microstructure after grafting and sulfonation. The results showed that the PVDF‐g‐PSSA membranes exhibited good thermal stability and lower methanol permeability. The proton conductivity of PVDF‐g‐PSSA membranes was also measured by the electrochemical impedance spectroscopy method. It was found that the proton conductivity of PVDF‐g‐PSSA membranes depends on the degree of sulfonation. All the sulfonated membranes show high proton conductivity at 92°C, in the range of 27 to 235 mScm⁻¹, which is much higher than that of Nafion212 (102 mScm⁻¹ at 80°C). The results indicated that the PVDF‐g‐PSSA membranes are particularly promising membranes to be used as polymer electrolyte membranes due to their excellent stability, low methanol permeability, and high proton conductivity.     

Synthesis and properties of novel sulfonated polyimides containing binaphthyl groups as proton‐exchange membranes for fuel cells

A novel sulfonated diamine monomer, 2,2′‐bis(p‐aminophenoxy)‐1,1′‐binaphthyl‐6,6′‐disulfonic acid (BNDADS), was synthesized. A series of sulfonated polyimide copolymers containing 30–80 mol % BNDADS as a hydrophilic component were prepared. The copolymers showed excellent solubility and good film‐forming capability. Atomic force microscopy phase images clearly showed hydrophilic/hydrophobic microphase separation. The relationship between the proton conductivity and degree of sulfonation was examined. The sulfonated polyimide copolymer with 60 mol % BNDADS showed higher proton conductivity (0.0945–0.161 S/cm) at 20–80 °C in liquid water. The membranes exhibited methanol permeability from 9 × 10^?8 to 5 × 10^?7 cm²/s at 20 °C, which was much lower than that of Nafion (2 × 10^?6cm²/s). The copolymers were thermally stable up to 300 °C. The sulfonated polyimide copolymers with 30–60 mol % BNDADS showed reasonable mechanical strength; for example, the maximum tensile strength at break of the sulfonated polyimide copolymer with 40 mol % BNDADS was 80.6 MPa under high moisture conditions. The optimum concentration of BNDADS was found to be 60 mol % from the viewpoint of proton conductivity, methanol permeability, and membrane stability. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 222–231, 2007     

End-group cross-linked membranes based on highly sulfonated poly(arylene ether sulfone) with vinyl functionalized graphene oxide as a cross-linker and a filler for proton exchange membrane fuel cell application

High-performance end-group cross-linked sulfonated poly(arylene ether sulfone) (SPAES) membranes are developed using thiolate-terminated SPAES with very high degree of sulfonation (DS) such as 90 mol% (SK-SPAES90) and vinyl functionalized graphene oxide (VGO) as a cross-linker and a filler through the thiol-Michael addition reaction. Since free-standing membranes for fuel cell application could not be prepared using the water soluble and highly proton conductive SPAES with high DS of 90 mol%, cross-linked SPAES90 membranes are intentionally prepared. The cross-linked membranes are found to have good physicochemical properties with excellent proton conductivity that can be applied for the proton exchange membrane. In particular, the cross-linked SPAES90 membrane prepared using 1.0 wt% of VGO exhibits better dimensional stability than a SPAES70 membrane from the linear SPAES with DS of 70 mol% and the proton conductivities of this membrane are larger than those of Nafion 211 at 80 °C under different relative humidity conditions (40%-95%).     

Sulfonated poly(arylene thioether phosphine oxide)s copolymers for proton exchange membrane fuel cells

High molecular weight sulfonated poly(arylene thioether phosphine oxide)s (sPATPO) with various sulfonation degrees were prepared directly by aromatic nucleophilic polycondensation of 4,4′-thiobisbenzenethiol with sulfonated bis(4-fluorophenyl) phenyl phosphine oxide and bis(4-fluorophenyl) phenyl phosphine oxide. sPATPO in the acid form with sulfonation degrees of 60–100% exhibits a glass transition temperature higher than 230 °C and a 5% weight loss temperature above 400 °C, indicating high thermal stability. sPATPO with a high sulfonation degree shows high proton conductivity and good resistance to swelling as well. For instance, sPATPO-70 displays the conductivity of 0.0783 S/cm and a swelling ratio of 11.6% at 90 °C. TEM micrographs showed that sPATPO membranes with a high sulfonation degree could form continuous ion channels, which are favorable for improving the proton conductivity but harmful to remaining the mechanical property. The membranes are expected to show good performances in fuel cell applications.     

Sulfonated Poly(ether ether ketone) and Poly(ethylene glycol) Diacrylate Based Semi-Interpenetrating Network Membranes for Fuel Cells

Polymer electrolyte membranes are prepared from novel semi-interpenetrating polymer network material where the sulfonated poly (ether ether ketone) (SPEEK) is the linear polymer and the poly (ethylene glycol) diacrylate (PEGDA) is the cross-linking constituent. The semi-IPN is prepared by in situ polymerization of PEGDA in the presence of sulfonated poly (ether ether ketone). SPEEK is prepared by direct sulfonation of commercial PEEK (Gatone? 1100) by reported procedures. SPEEK with degree of sulfonation 63% (calculated from FT-NMR) is selected as the base membrane and different semi-IPN membranes were prepared by varying the PEGDA and SPEEK ratio. The degree of sulfonation of SPEEK and the formation of semi-IPN were confirmed by spectroscopy studies. The various semi-IPN membranes were characterized for ion-exchange capacity, water uptake, hydrolytic stability, proton conductivity and thermal stability for evaluating the suitability of these membranes for fuel cells. The proton conductivity of the membranes decreased with increasing PEGDA content. The Semi-IPN membranes exhibited conductivities (30°C) from 0.018 S/cm to 0.006 S/cm. These interpenetrating network membranes showed higher hydrolytic stability than the pure SPEEK membrane. This study shows that semi-IPN membranes based on PEGDA and SPEEK can be viable candidates for electrolyte membranes.     

Polyantimonic acid-based materials evaluated as moisture sensors at ambient temperature

Humidity sensors are in high demand for many applications, such as environmental monitoring and air and food quality control. Despite many inorganic and organic materials exhibit moisture sensing properties, the electrical response of many existing sensors is not stable along the time. Polyantimonic acid (PAA) is characterized by elevated proton conductivity and by high thermal stability: consequently, it is seen as promising proton conductor for usage in humidity sensing devices. In this work, for the first time, PAA-based bulk solid membranes were produced and tested as potential materials for relative humidity (RH) detection and their moisture sensitivity was evaluated. Two different amounts of binder were used for moulding the solid sensors: the ones with 10% of binder were designated as 90PAA, while the ones with 20% were named 80PAA. The structures of the solid samples were investigated by X-ray diffraction (XRD) technique, adsorption–desorption curves via Brunauer–Emmett–Teller (BET), scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) techniques. The electrical behaviour was examined at ambient temperature by electrical impedance spectroscopy in the entire relative humidity (RH) interval (0–100%) and in the frequency range of 40 Hz up to 60 MHz. Electrical response of the materials was correlated with the structural features of the membranes. Both 90PAA and 80PAA sensors showed total resistance 3 × 10⁵ and 3.5 × 10⁵ Ω at 10% RH, respectively. A linear decrease of the resistance on RH was observed in the range 30–90% RH for both sensors. The electrical response of the evaluated PAA-based sensors displays good repeatability and reproducibility: the ones with lower binder content showed higher moisture sensitivity as well as very good time stability over 1 year.

     

Synthesis of novel proton‐conducting highly sulfonated polybenzimidazoles for PEMFC and the effect of the type of bisphenyl bridge on polymer and membrane properties

Six series of novel highly sulfonated polybenzimidazoles (sPBIs) with high molecular weight were prepared by direct polycondensation between 3,3′‐diaminobenzidine and original multisulfonated dinuclear dicarboxylic acids containing bridging ether, sulfone, and hexafluoroisopropylidene moieties. All reactions were carried out in polyphosphoric acid, which acts as both solvent and catalyst. The degree of sulfonation was modulated in the final products by varying the proportion of sulfonated to nonsulfonated dicarboxylic acids used in the synthesis. The high purity of the disulfonated and tetrasulfonated monomers allows wholly sulfonated homopolymers to be obtained. Confirmation of the chemical structure and the degree of sulfonation were derived from ¹H nuclear magnetic resonance spectroscopy. Inherent viscosity was estimated as between 0.70 and 5.33 dL g^?1 for sPBIs with ion exchange capacity in the range 0.87–4.68 mequiv g^?1. Dynamic thermogravimetric analysis in air showed no weight loss below 350 °C (heating rate 5 °C min^?1). The nature of the bisphenyl bridge has clear influence on the water uptake and proton conduction properties of the resulting sPBI membranes, with hexafluoroisopropylidene links providing materials of highest conductivity as well as favoring film‐forming characteristics. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Highly sensitive,humidity-tolerant and flexible NO2 sensors based on nanoplate Bi2Se3 film

Recently, two-dimension (2D) materials have fueled considerable interest in the field of gas sensing to cope urgent demands at specific scenarios. Unfortunately, the susceptibility to ambient humidity, and/or fragile operation stability always frustrate their further practicability. To overcome these drawbacks, we proposed one novel flexible gas sensor based on bismuth selenide (Bi₂Se₃) nanoplates for sensitive NO₂ detection at room temperature. The as-prepared Bi₂Se₃ sensor exhibited favorable sensing performance, including remarkable NO₂ selectivity, high response of 120% and fast response time of 81 s toward 5 ppm NO₂, an ultralow detection limit of 100 ppb, and nice stability. Besides, the excellent humidity tolerance and mechanical flexibility endowed Bi₂Se₃ sensors with admirable reliability under harsh working conditions. The first-principles calculation further revealed the insights of extraordinary NO₂ selectivity and the underlying gas-sensing mechanism.     

Synthesis and properties of novel sulfonated polyimides containing phthalazinone moieties for PEMFC

A novel sulfonated diamine, 1,2-dihydro-2-(3-sulfonic-4-aminophenyl)-4-[4-(3-sulfonic-4-aminophenoxy)-phenyl]-phthalazin-1-one(S-DHPZDA), was successfully synthesized and two series of six-membered sulfonated polyimides (SPIs) were prepared from 1,4,5,8-naphthalenetetracarboxylic dianhydride (NTDA), S-DHPZDA, and nonsulfonated diamines DHPZDA or 4,4′-diaminodiphenyl ether (ODA). The chemical structure of the S-DHPZDA and the SPIs were characterized by ¹H NMR and FT-IR. Tough, brownish and transparent membranes were cast from SPIs’ solution in NMP. The water uptake, swelling ratio, chemical and thermal stability, hydrolytic and oxidative stability as well as proton conductivity of these new polymers were investigated systematically. Compared with Nafions, the obtained SPI membranes have onset decomposed temperatures of these two series SPIs were above 318 °C and decomposed temperature of main chain were 565 °C and excellent dimension stabilities on similar IECs. Introduction of phthalazinone moieties had improved the copolyimides’ solubility in polar aprotic organic solvents like m-cresol, NMP, DMSO, DMF etc. The SPIs had high proton conductivity (σ) in the order of magnitude of 10⁻³ to 10⁻² S cm⁻¹ depending on the degree of sulfonation (DS) of the polymers.     

Controlled drug release studies of atenolol using differently sulfonated acryloxyacetophenone and methyl methacrylate copolymer resins as drug carriers

2-Acryloxyacetophenone(AAP) was prepared and subjected to suspension polymerization with methyl methacrylate(MMA) using azobisisobutyronitrile(AIBN) as free radical initiator.The differently sulfonated AAP-MMA cross-linked copolymer cationic exchange resins were prepared by sulfonation with concentrated sulphuric acid at 70 °C.Several characteristics of the prepared resins were evaluated,i.e.FTIR,the ion-exchange capacity(IEC),thermo gravimetric analysis(TGA),particle size distribution and microscopic morphology.The resin characteristics were altered with degree of sulfonation,providing that differently sulfonated resins could be prepared.The behavior of atenolol(ATL) loading and in vitro release in the USP stimulated gastric and intestinal fluids of the obtained resins were evaluated.The drug loaded in the resin increased with increasing degree of sulfonation and hence the drug binding site in resin employed.The drug release was lower from the resins with higher content of sulfonic group due to the increase in the diffusive path depth.The drug release was a little lower in stimulated gastric fluid(SGF) than in stimulated intestinal fluids(SIF).The basic groups,ionized to a little greater extent in SGF and preferred binding with the resin rather than releasing.Hence,the differently sulfonated resins could be utilized as novel carriers for drug delivery.     

Preparation and characterizations of asymmetric sulfonated polysulfone membranes by wet phase inversion method

This paper presents an original approach to prepare the asymmetric sulfonated polysulfone membranes by using wet phase inversion method and their applications for dehydrating a water/ethanol mixture by pervaporation. The separation performances of sulfonated membranes were strongly affected by the degree of sulfonation and the degree of swelling of membranes. The substitution degree of sulfonic group enhanced the permselectivity of sulfonated polysulfone membranes by increasing the hydrophilicity of polymer backbone. Based on the observations of membrane morphology and light transmittance measurements, the degree of sulfonation of polysulfone presented less influence on the membrane formation pathway and the final structure of membrane in wet phase inversion process. It was also found that the sulfonated membranes showed well hydrophilic properties and facilitated water adsorption in the membranes. The sorption and permeation properties also showed that the permselectivity of asymmetric membrane was dominated by the permeate diffusion rather than the permeate sorption in the skin layer. The high separation performance of pervaporation membrane can be achieved by phase inverse method with sulfonated polysulfone.     

SYNTHESIS AND PROPERTIES OF SULFONATED POLY（ARYLENE ETHER） CONTAINING TRIPHENYL METHANE MOIETIES FROM ISOCYNATE MASKED BISPHENOL

A novel sulfonated poly（arylene ether） containing triphenylmethane moieties was synthesized by the sulfonation of a designed parent polymer using chlorosulfonic acid as sulfonation agent. The sulfonation took place at the para position of the pendant phenyl rings because of the specially designed parent polymer. The position and degree of sulfonation were characterized by ^1H-NMR and elemental analysis. The sulfonated polymers are highly soluble in common organic solvents, such as dimethylsulfoxide, N,N＇-dimethylacetamide, dimethylformamide, ethylene glycol monomethyl ether, and can be readily cast into tough and smooth films from solutions. The films showed good thermal and hydrolysis stabilities. Moreover, Fenton＇s reagent test revealed that the films exhibited superior stability to oxidation. The proton conductivities of the films were comparable with Nation 117 under same conditions. The membrane electrode assembly （MEA） prepared with the asmade film （706 EW, 100 μm dry thickness） shows better cell performance than Nation 115-MEA in the whole current density range.     

Sulfonated poly(styrene-isobutylene-styrene) grafted with hexyl- and butyl-imidazolium chloride ionic liquids

In this work, novel sulfonated poly(ionic liquid)s block-copolymers based on poly(styrene–isobutylene–styrene) (SIBS) are synthesized for chemical protective clothing (CPC) applications. The synthesis consists of the chloromethylation of SIBS, followed by the incorporation of N-alkylimidazole through chemical grafting, and concluding with sulfonation of the resulting compound. Properties of the membranes are determined as a function of different N-alkylimidazoles (butylimidazole and hexylimidazole) and sulfonation levels (7–23 mol%). Results show that the incorporation of imidazole and sulfonic groups increases the thermal stability of SIBS as well as its water absorption capabilities. The interaction between the ionic moieties in the polymeric matrix allows the formation of hydrophilic nanochannels, which promote the transport of permeants through the membrane. The high water vapor transmission rate (above 2000 g m⁻² day⁻¹) and values of selectivity (~50) demonstrate that the breathability of the synthesized membrane is improved while blocking the passage of dimethyl methylphosphonate (simulant of agent Sarin). The above mentioned observations suggest that sulfonated SIBS-PIL's membranes are potential materials for CPC applications.     

New sulfonated engineering polymers via the metalation route. I. Sulfonated poly(ethersulfone) PSU Udel® via metalation-sulfination-oxidation

A new process has been developed for the sulfonation of arylene polymers which can be lithiated, like polysulfone Udel®. The sulfonation process consists of the following steps: (1) lithiation of the polymer at temperatures from −50 to −80°C under argon, (2) gassing of the lithiated polymer with SO₂; (3) oxidation of the formed polymeric sulfinate with H₂O₂, NaOCl, or KMnO₄; (4) ion-exchange of the lithium salt of the sulfonic acid in aqueous HCl. The advantages of the presented sulfonation procedure are: (1) in principle all polymers which can be lithiated can be subjected to this sulfonation process; (2) by this sulfonation procedure the sulfonic acid group is inserted into the more hydrolysis-stable part of the molecule; (3) this process is ecologically less harmful than many common sulfonation procedures. The sulfonated polymers were characterized by NMR, titration and elemental analysis, by IR spectroscopy, and by determination of ionic conductivity. Also the hydrolytic stability of the sulfonated ion-exchange polymers was investigated. Polymers with an ion-exchange capacity of 0.5 to 3.2 mequiv SO₃H/g Polymer have been synthesized and characterized. The following results have been achieved: membranes made from the sulfonated polymers show good conductivity, good permselectivity (>90%), and good hydrolytic stability in 1N HCl and water at temperatures up to 80°C. © 1996 John Wiley & Sons, Inc.