Enhanced electrochemical performance of SnS nanoparticles/CNTs composite as anode material for sodium-ion battery

SnS/CNTs composite as anode for SIBs exhibits high reversible capacity, good cyclability as well as rate performance, which is superior to that of pure SnS. The enhanced electrochemical performance can be attributed to the adding of CNTs as a flexible and conductive structure supporter and the formation of SnS nanoparticles with small diameter.     

NiSe2 nanoparticles encapsulated in CNTs covered and N-doped TiN/carbon nanofibers as a binder-free anode for advanced sodium-ion batteries

Metal selenides are promising anodes for sodium-ion batteries (SIBs) due to the high theoretical capacity through conversion reaction mechanism. However, developing metal selenides with superior electrochemical sodium-ion storage performance is still a great challenge. In this work, a novel composite material of free-standing NiSe₂ nanoparticles encapsulated in N-doped TiN/carbon composite nanofibers with carbon nanotubes (CNTs) in-situ grown on the surface (NiSe₂@N-TCF/CNTs) is prepared by electrospinning and pyrolysis technique. In this composite materials, NiSe₂ nanoparticles on the surface of carbon nanofibers were encapsulated into CNTs, thus avoiding aggregation. The in-situ grown CNTs not only improve the conductivity but also act as a buffer to accommodate the volume expansion. TiN inside the nanofibers further enhances the conductivity and structural stability of carbon-based nanofibers. When directly used as anode for SIBs, the NiSe₂@N-TCF/CNT electrode delivered a reversible capacity of 392.1 mAh/g after 1000 cycles and still maintained 334.4 mAh/g even at a high rate of 2 A/g. The excellent sodium-ion storage performance can be attributed to the fast Na⁺ diffusion and transfer rate and the pseudocapacitance dominated charge storage mechanism, as is evidenced by kinetic analysis. The work provides a novel approach to the fabrication of high-performance anode materials for other batteries.     

Protection of Li metal anode by surface-coating of PVDF thin film to enhance the cycling performance of Li batteries

The PVDF thin film on the surface of the lithium metal can highly suppress the lithium dendrites.     

Ni3S2@碳纳米管复合材料的制备及其储钠性能

采用一步固相煅烧工艺制备了碳纳米管原位封装Ni₃S₂纳米颗粒（Ni₃S₂@CNT）,并研究了其作为钠离子电池（SIBs）负极材料的电化学性能. 通过X射线衍射（XRD）、扫描电子显微镜（SEM）、透射电子显微镜（TEM）、循环伏安测试、恒流充放电以及交流阻抗等研究了Ni₃S₂@CNT的物相结构、形貌特征以及电化学性能. 电化学测试表明,材料在100 mA·g ^-1电流密度下,放电容量可以达到541.6 mAh·g ^-1,甚至在2000 mA·g ^-1的大电流密度下其放电比容量也可以维持在274.5 mAh·g ^-1. 另外,材料在100 mA·g ^-1电流密度下,经过120周充放电循环后其放电和充电比容量仍然可以保持在374.5 mAh·g ^-1和359.3 mAh·g ^-1,说明其具有良好倍率性能和循环稳定性能. 良好的电化学性能归因于这种独特的碳纳米管原位封装Ni₃S₂纳米颗粒结构. 碳纳米管不但可以提高复合材料的导电性,也可以缓冲Ni₃S₂纳米颗粒在反复充放电过程中产生的体积膨胀效应,明显改善了Ni₃S₂@CNT负极复合材料的电化学性能.     

Se-decorated SnO2/rGO composite spheres and their sodium storage performances

SnO₂ is considered a promising anode material for sodium-ion batteries due to its high theoretical capacity and low cost.However,the poor electrical conductivity and dramatic volume variation during cha rge/discharge cycling is a major limitation in its practical applicability.Here we propose a simple onepot spray pyrolysis process to construct unique pomegranate-like SnO₂/rGO/Se spheres.The ideal structural configuration of these architectures was effective in alleviating the large volume variation of SnO₂,besides facilitating rapid electron transfer,allowing the devised anode to exhibit superior sodium sto rage performances in terms of capacity(506.7 mAh/g at 30 mA/g),cycle performance(397 mAh/g after100 cycles at 50 mA/g) and rate capability(188.9 mAh/g at an ultrahigh current density of 10 A/g).The experimental evidence confirms the practical workability of p-SnO₂/rGO/Se spheres in SIBs.     

Facile synthesized Cu-SnO2 anode materials with three-dimensional metal cluster conducting architecture for high performance lithium-ion batteries

A novel Cu-SnO₂ anode material derived from Cu₆Sn₅ alloy, retaining high conductivity of Cu and high theoretical capacity of SnO₂ with a facile synthesizing process by oxidation and reduction method. The novel Cu structure penetrates in the composite particles inducing high conductivity and spaceconfined SnO₂, which restrict the pulverization of SnO₂ during lithiation/delithiation process.     

A novel synthesis of Nb_2O_5@rGO nanocomposite as anode material for superior sodium storage

The development of novel anode materials,with superior rate capability,is of utmost significance for the successful realization of sodium-ion batteries(SIBs).Herein,we present a nanocomposite of Nb_2 O_5 and reduced graphene oxide(rGO) by using hydrothermal-assisted microemulsion route.The water-in-oil microemulsion formed nanoreactors,which restrained the particle size of Nb_2 O_5 and shortened the diffusion length of ions.Moreover,the rGO network prevented agglomeration of Nb_2 O_5 nanoparticles and improved electronic conductivity.Consequently,Nb_2 O_5@rGO nanocomposite is employed as anode material in SIBs,delivering a capacity of 195 mAh/g after 200 charge/discharge cycles at 0.2 A/g.Moreover,owing to conductive rGO network,the Nb_2 O_5@rGO electrode rende red a specific capacity of 76 mAh/g at high current density of 10 A/g and maintained 98 mAh/g after 1000 charge/discharge cycles at 2 A/g.The Nb_2 O_5@rGO electrode material prepared by microemulsion method shows promising possibilities for application of SIBs.     

Facile Synthesis of Ultra-Small Few-Layer Nanostructured MoSe2 Embedded on N,P Co-Doped Bio-Carbon for High-Performance Half/Full Sodium-Ion and Potassium-Ion Batteries

Sodium/potassium-ion batteries (SIBs/PIBs) arouse intensive interest on account of the natural abundance of sodium/potassium resources, the competitive cost and appropriate redox potential. Nevertheless, the huge challenge for SIBs/PIBs lies in the scarcity of an anode material with high capacity and stable structure, which are capable of accommodating large-size ions during cycling. Furthermore, using sustainable natural biomass to fabricate electrodes for energy storage applications is a hot topic. Herein, an ultra-small few-layer nanostructured MoSe₂ embedded on N, P co-doped bio-carbon is reported, which is synthesized by using chlorella as the adsorbent and precursor. As a consequence, the MoSe₂/NP-C-2 composite represents exceedingly impressive electrochemical performance for both sodium-ion batteries (SIBs) and potassium-ion batteries (PIBs). It displays a promising reversible capacity (523 mAh g⁻¹ at 100 mA g⁻¹ after 100 cycles) and impressive long-term cycling performance (192 mAh g⁻¹ at 5 A g⁻¹ even after 1000 cycles) in SIBs, which are some of the best properties of MoSe₂-based anode materials for SIBs to date. To further probe the great potential applications, full SIBs pairing the MoSe₂/NP-C-2 composite anode with a Na₃V₂(PO₄)₃ cathode also exhibits a satisfactory capacity of 215 mAh g⁻¹ at 500 mA g⁻¹ after 100 cycles. Moreover, it also delivers a decent reversible capacity of 131 mAh g⁻¹ at 1 A g⁻¹ even after 250 cycles for PIBs.     

Nano-LiCoO2 as cathode material of large capacity and high rate capability for aqueous rechargeable lithium batteries

Crystalline nanoparticles of LiCoO₂ are prepared by a sol–gel method at 550 °C and characterized by X-ray diffraction. Their electrochemical behaviors were characterized by cyclic voltammograms, capacity measurement and cycling performance. Results show that the reversible capacity of the nano-LiCoO₂ can be up to 143 mAh/g at 1000 mA/g and still be 133 mAh/g at 10,000 mA/g (about 70C) in 0.5 mol/l Li₂SO₄ aqueous electrolyte. In addition, their cycling behavior is also very satisfactory, no evident capacity fading during the initial 40 cycles. These data present great promise for the application of aqueous rechargeable lithium batteries.     

Ether-based electrolyte enabled Na/FeS2 rechargeable batteries

We demonstrate for the first time that by simply substituting ether-based electrolyte (1.0 M NaCF₃SO₃ in diglyme) for the commonly used carbonate-based electrolyte, the cyclability of FeS₂ towards sodium storage can be significantly improved. A sodiation capacity over 600 mAh/g and a discharge energy density higher than 750 Wh/kg are obtained for FeS₂ at 20 mA/g. When tested at 60 mA/g, FeS₂ presents a sodiation capacity of 530 mAh/g and retains 450 mAh/g after 100 cycles, much better than the cycling performance of Na/FeS₂ tested in carbonate-based electrolyte.     

多孔纳米立方FeSe2/石墨烯复合材料的可控构建及在钠离子电池中的应用

设计具有较高比容量和循环稳定性的负极材料对于钠离子电池的发展至关重要。过渡金属硒化物因其具有较高的理论容量而成为潜在的负极材料。但是,硒化物电导率低下且在钠离子嵌入/脱出的过程中会发生较大程度的体积膨胀,导致比容量快速下降。因此,结构调控显得尤为重要。通过常规水热法在二维还原氧化石墨烯（rGO）上原位生长多孔纳米立方体FeSe₂,制备了具有更多活性位点和结构更加稳定的FeSe₂/rGO复合材料。当用作钠离子电池的负极时,复合材料FeSe₂/rGO在0.2 A/g时比容量为694.6 mA?h/g,在2.0 A/g电流密度下,循环300圈后比容量为300 mA?h/g。     

Matryoshka-type carbon-stabilized hollow Si spheres as an advanced anode material for lithium-ion batteries

Silicon(Si) is regarded as the potential anode for lithium-ion batteries(LIBs), due to the remarkable theoretical specific capacity and low voltage plateau. However, the rapid capacity decay resulting from volume variation and slow electron/ion transportation of Si limit its practical application. Here, matryoshka-type carbon-stabilized hollow silicon spheres(Si/C/Si/C) are synthesized by an aluminothermic reduction and calcination process. The Si/C/Si/C anode materials prepared at 500 ℃(Si/C/Si...     

碳布负载的缺氧型Na2Ti3O7纳米带阵列作为高性能柔性钠离子电池负极材料

作为锂离子电池的理想替代品,钠离子电池因具有能源储备丰富、成本低廉等优点而受到人们的广泛关注。柔性便携式电子产品的发展亟需柔性储能器件的研制。因此,发展一种廉价、高性能的柔性钠离子电池负极材料成了科研工作者的共同目标。在此项工作中,我们通过简单的水热合成和热还原法发展了一种以柔性碳布为基底,与缺氧型的Na₂Ti₃O₇纳米带(NTO)构成三维阵列结构的新型柔性钠离子电池负极材料。复合材料(R-NTO/CC)的导电性和活性位点得到提高,电化学性能也大幅提升,在200 mA·cm^-2的电流密度下,实现100 mAh·cm^-2的面积比容量,且经过200次循环后仍保留最初电容值的80%。此外,这种电极还具有优良的倍率性能,当电流密度提高到400 mA·cm^-2时,仍保持69.7 mAh·cm^-2的面积比容量,是未引入氧空位材料的三倍之多。这种三维缺氧的电极材料可有效提高载流子浓度,缩短离子传输通道,从而大幅提升电极的电化学性能。此工作为设计合成高储钠性能的新型的负极材料提供了一种实用有效的策略。     

B-incorporated,N-doped hierarchically porous carbon nanosheets as anodes for boosted potassium storage capability

Carbonaceous nanomaterials with porous structure have become the highly promising anode materials for potassium-ion batteries(PIBs) due to their abundant resources, low-cost, and excellent conductivity. Nevertheless, the sluggish reaction kinetics and inferior cycling life caused by the large radius of K ions severely restrict their commercial development. Herein, B,N co-doped hierarchically porous carbon nanosheets(BNPC) are achieved via a facile template-assisted route, followed by a simple on...     

Carbon-coated Li3VO4 with optimized structure as high capacity anode material for lithium-ion capacitors

Due to the high capacity,moderate voltage platform,and stable structure,Li₃VO₄(LVO) has attracted close attention as feasible anode material for lithium-ion capacitor.However,the intrinsic low electronic conductivity and sluggish kinetics of the Li⁺ insertion process severely impede its practical application in lithium-ion capacitors(LICs).Herein,a carbon-coated Li₃VO₄(LVO/C) hierarchical structure was prepared by a facial one-step solid-sta...     

Hexagonal FeNi2Se4@C Nanoflakes as High Performance Anode Materials for Sodium-ion Batteries

Metal selenides have drawn significant attention as promising anode materials for sodium-ion batteries(SIBs)owing to their high electronic conductivity and reversible capacity.Herein,hexagonal FeNi2Se4@C nanoflakes were synthesized via a facile one-step hydrothermal method.They deliver a reversible capacity of 480.7 mA·h/g at 500 mA/g and a high initial Coulombic efficiency of 87.8%.Furthermore,a discharge capacity of 444.8 mA·h/g can be achieved at 1000 mA/g after 180 cycles.The sodium storage mechanism of FeNi2Se4@C is uncovered.In the discharge process,Fe and Ni nanoparticles are generated and distributed in Na2Se matrix homogeneously.In the charge process,FeNi2Se4 phase is formed reversibly.The reversible phase conversion of FeNi2Se4@C during cycling is responsible for the excellent electrochemical performance and enables FeNi2Se4@C nanoflakes promising anode materials for SIBs.     

Porous nanocomposite derived from Zn,Ni-bimetallic metal-organic framework as an anode material for lithium-ion batteries

A highly stable and Zn, Ni-bimetallic porous composite was synthesized via a one-step pyrolysis of a bimetal-organic framework as an efficient anode material for lithium-ion batteries. Remarkably the obtained composite shows 1105.2 mAh/g at a current density of 5000 mA/g after 400 cycles which makes it a promising candidate to improve the volumetric energy density.     

SiO/CNTs: A new anode composition for lithium-ion battery

A new anode composition SiO/CNTs (carbon nanotubes) has been prepared by chemical vapor deposition (CVD) method. The results of scanning electron microscopy (SEM) confirm that CNTs deposit on small SiO particles, form a cage, and enwrap SiO particles tightly. SiO/CNTs anode composition exhibits an initial discharge and charge capacity of 1171 and 789 mAh/g, and maintains a reversible capacity of 500 mAh/g after 80 cycles. The improvement of the cyclic performance for SiO/CNTs composition is related to the maintaining of the electric network during cycling, which benefits from a tight contact between CNTs and SiO particles.     

Polydopamine-mediated synthesis of Si@carbon@graphene aerogels for enhanced lithium storage with long cycle life

The application of Si as the anode materials for lithium-ion batteries (LIBs) is still severely hindered by the rapid capacity decay due to the structural damage caused by large volume change (> 300%) during cycling. Herein, a three-dimensional (3D) aerogel anode of Si@carbon@graphene (SCG) is rationally constructed via a polydopamine-assisted strategy. Polydopamine is coated on Si nanoparticles to serve as an interface linker to initiate the assembly of Si and graphene oxide, which plays a crucial role in the successful fabrication of SCG aerogels. After annealing the polydopamine is converted into N-doped carbon (N-carbon) coatings to protect Si materials. The dual protection from N-carbon and graphene aerogels synergistically improves the structural stability and electronic conductivity of Si, thereby leading to the significantly improved lithium storage properties. Electrochemical tests show that the SCG with optimized graphene content delivers a high capacity (712 mAh/g at 100 mA/g) and robust cycling stability (402 mAh/g at 1 A/g after 1500 cycles). Furthermore, the full cell using SCG aerogels as anode exhibits a reversible capacity of 187.6 mAh/g after 80 cycles at 0.1 A/g. This work provides a plausible strategy for developing Si anode in LIBs.     

Graphene-supported cobalt nanoparticles used to activate SiO2-based anode for lithium-ion batteries

Although SiO₂-based anode is a strong competitor to supersede graphite anode for lithium-ion batteries, it still has problems such as low electrochemical activity, enormous loss of active lithium, and serious volume expansion. In order to solve these problems, we used a graphene network loaded with cobalt metal nanoparticles (rGO–Co) to coat SiO₂ porous hollow spheres (SiO₂@rGO–Co). The construction of porous hollow structure and graphene network can shorten the lithium-ion (Li⁺) diffusion distance and enhance the conductivity of the composite, which improves the electrochemical activity of SiO₂ effectively. They also alleviate the volume expansion of the anode in the cycling process. Moreover, nano-scale cobalt metal particles dispersed on graphene catalyze the conversion reaction of SiO₂ and activate the locked Li⁺ in Li₂O through a reversible reaction, which improves the charge and discharge capacity of the anode. The capacity of SiO₂@rGO–Co reaches 370.4 mAh/g after 100 cycles at 0.1 A/g, which is 6.19 times the capacity of pure SiO₂ (59.8 mAh/g) under the same circumstance. What is more, its structure also exhibits excellent cycle stability, with a volume expansion rate of only 13.0% after 100 cycles at a current density of 0.1 A/g.