Comparison of inductively coupled plasma–atomic emission spectrometry, anodic stripping voltammetry and instrumental neutron-activation analysis for the determination of heavy metals in airborne particulate matter

The capability of three analytical techniques, inductively coupled plasma–atomic emission spectrometry (ICP–AES), anodic stripping voltammetry (ASV), and instrumental neutron-activation analysis (INAA) have been compared for the determination of Cd, Fe, Pb, and Zn in airborne particulate matter, collected on cellulose filters, from the atmosphere of the large area of Thessaloniki, Greece. Two procedures were tested for quantitative leaching of these elements from the filters before ICP–AES and ASV, digestion with aqua regia in a Teflon autoclave, after dissolution of the organic matter with HClO₄ under ambient conditions, and ultrasonic extraction with a mixture of HNO₃ and HCl. Validation of the leaching and digestion procedures revealed that digestion in the autoclave is more effective, especially for Fe. The concentrations of these elements over a decade in both industrial and urban areas of the investigated region are compared.     

Determination of trace elements in Antarctic krill samples by inductively coupled atomic emission and graphite furnace atomic absorption spectrometry

Analytical methods were developed for the determination of trace elements in Antarctic krill samples applying inductively coupled plasma atomic emission spectrometry (ICP-AES) and graphite furnace atomic absorption spectrometry (GF-AAS). Cu, Fe, Mn and Zn were determined by ICP-AES, while Cd and Pb by GF-AAS technique. Two microwave assisted digestion procedures were elaborated for the preparation of 0.5-g krill samples using open and closed vessel systems. The efficiency of the digestion processes was checked by measurements of the total organic carbon content of the solutions obtained. The deviations of the analytical data from the certified values and the relative standard deviations of the concentration measurements were lower for all six elements investigated applying the closed vessel digestion system.     

Optimization of an urban particulate matter multi-element analysis method by inductively coupled plasma--atomic emission spectrometry (ICP-AES)

In the present work a method for simultaneous metals determination, in urban air particulate matter by ICP-AES has been set up. A large number of elements (18) has been analyzed, including major (Al, Fe, K, and Mg), minor (Na, Pb and Zn) and trace (As, Cd, Co, Cr, Cu, Hg, Mn, Ni, Sb, Sr and V) elements. The procedure consists of microwave sample acidic total digestion by HNO3/HF mixture and subsequent analysis by ICP-AES, using different assemblies depending on sample treatment procedure: a quartz Meinhard nebulizer/cyclonic chamber, if HF excess was eliminated, or a cross-flow nebulizer/plastic Scott chamber, suitable for application with HF. A cyclonic chamber for hydride generation was used for As, Sb and Hg determination. The procedure was tested with Standard Reference Materials 1648 NIST Urban Particulate Matter and Certified Reference Material No8 NIES "Vehicle Exhaust Particulates". Two sampling supports, quartz fibre and polycarbonate filters, have been examined in order to find the most suitable i.e. the one characterized by less interference. Some real samples of urban air particulate matter, TSP, PM10 and PM2.5 fractions, collected during an intercomparison campaign promoted by Regione Lombardia, have been analyzed with the procedure developed.     

Determination of metal concentrations in lichen samples by inductively coupled plasma atomic emission spectroscopy technique after applying different digestion procedures

Three digestion procedures have been tested on lichen samples for application in the determination of major, minor and trace elements (Al, Ca, Cd, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, Pb, V and Zn) in lichen samples collected in Aegean Region of Turkey by inductively coupled plasma atomic emission spectrometer (ICP-AES). The acid mixture of concentrated HNO₃, H₂O₂ and HF were used. The instrument was optimized using lichen matrix considering RF power, nebulizer pressure, auxiliary flow rate and pump rate. The accuracy of the overall analyses was first estimated by analysis of two certified reference materials. Good agreement between measured and reference values were found for almost all elements. As the second way of determining the accuracy, results obtained from independent analytical techniques (ICP-AES and instrumental neutron activation analysis (INAA)) were compared for all elements by analyzing real samples. Correlation coefficients of two techniques for the elements ranged between 0.70 (Mg) and 0.96 (Fe). Among the three digestion systems, namely microwave, open vessel and acid bomb, microwave digestion system gave the best recovery results. The method detection limit (MDL) was computed using reagent blanks of microwave digestion system since it provides cleaner sample preparation. Detection limit is adequate for all elements to determine the elements in lichen samples. The precision was assessed from the replicate analyses of reagent blanks of microwave digestion system and was found to be less than 1.5% relative standard deviation (R.S.D.).     

Comparison of microwave-assisted acid leaching techniques for the determination of heavy metals in sediments, soils, and sludges

Microwave-assisted EPA method 3051 for nitric acid leaching of environmentally key elements from sediments, soils, and sludges was tested, and the influence of leaching temperature and time on element recovery for an estuarine sediment (CRM 277) was investigated. The extraction efficiencies for four certified reference materials applying EPA method 3051, an optimized nitric acid procedure, and an aqua regia (HCl/HNO₃ 3:1) procedure were compared. Digestions were carried out in a high-pressure microwave system offering simultaneous temperature and pressure control for all digestion vessels employed. Eight elements (Cd, Co, Cr, Cu, Hg, Ni, Pb, and Zn) were determined by ICP-AES and ICP-MS. Extraction efficiency strongly depended on the applied leaching parameters and varied for certain elements among different materials when a nitric acid procedure was applied. In general, element recoveries obtained from the aqua regia procedure were superior to those obtained from nitric acid procedures and showed good agreement with the 95% confidence interval of the certified value for most of the elements investigated. Received: 27 March 1998 / Revised: 29 June 1998 / Accepted: 3 July 1998     

Characterisation of biological RMs for potential use in human brain analysis

Summary In order to investigate the precision and accuracy obtainable with instrumental neutron activation analysis (INAA) and inductively coupled plasma atomic emission spectrometry (ICP-AES), five different biological reference materials were analyzed. Four of them originated from the US National Institute of Standards and Technology (NIST) (Bovine Liver (SRM 1577; 1577/a; 185/A), Orchard Leaves (SRM 1571)) and one of them came from the International Atomic Energy Agency (IAEA) (Animal muscle (H-4)). The decomposition efficiency of microwave acid digestion was examined in comparison to digestions carried out in a Parrbomb. Five to ten subsamples of each material were subjected to the two digestion procedures and the solutions were analyzed by ICP-AES. The dried samples were analyzed by INAA. Up to 16 elements (Al, B, Ca, Co, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, P, Pb, S, Zn) were determined in various materials.     

Comparative study of pretreatment methods for the determination of metals in atmospheric aerosol by electrothermal atomic absorption spectrometry

A comparative study of pretreatment methods for the determination of 10 elements (As, Cd, Pb, V, Ni, Mn, Cr, Cu, Fe, Al) in atmospheric aerosols by electrothermal atomic absorption spectrometry (ETAAS) was conducted. For the digestion of the particulates collected in filters, six methods were compared using a mixture of HNO₃ and HF with or without the addition of various oxidative agents (HClO₄ or H₂O₂) or acids (HCl). The comparative study was performed using loaded cellulose filter samples, which were digested in Parr bombs and heated in a conventional oven at 170 °C for 5 h. The extraction efficiency and blanks were compared and it was proved that the digestion method using only HNO₃–HF extracted most of the metals and gave the lowest blanks. The HNO₃–HF mixture was selected for the development of an improved microwave digestion method specific for aerosol-loaded filters. The operating parameters were optimized, so that quantitative recovery of the reference materials NIST 1649a urban dust and NIST 1648 urban particulate matter was achieved. The blank of cellulose and teflon filters were also determined and compared. Teflon filters present the lowest blanks for all the elements. The obtained limits of detection for each type of filters were adequate for environmental monitoring purposes. ETAAS instrumental operation was also optimized for the compensation and the elimination of interferences. The temperature optimization was performed for each metal in every type of filter and optimized parameters are proposed for 10 elements.     

Speciation of Se,Fe and Zn in Human Milk Whey: The use of Instrumental Neutron Activation Analysis (INAA) to corroborate element profiles measured with Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)

In human milk trace elements normally exist in a form which can easily be absorbed by the newborn infant. For investigations of the bioavailability of trace elements it is necessary to carry out a speciation analysis of the elements of interest. An independent analytical method has been used for the quality control of the shape of the element profiles obtained from the speciation analysis of Se, Fe and Zn in individual samples of human milk whey after chromatographic separation. For the element detection in the untreated milk fractions Instrumental Neutron Activation Analysis (INAA) was chosen as the reference method. Element distribution patterns have been obtained with Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) using on-line digestion of the fraction, reduction and hydride formation of Se ("T"-mode). Prior results are compared with those obtained by means of element detection in the untreated fractions ("U"-mode) with ICP-AES. The elution profiles of Se, Fe and Zn in human milk whey obtained by means of ICP-AES detection using the "T"-mode show good agreement with the distribution patterns obtained with INAA. Recoveries of 103% for Fe, 86% for Zn and 87% for Se were obtained. The element distribution patterns of Fe and Zn obtained with ICP-AES speciation using the "T"-mode also show good agreement with those obtained by means of ICP-AES using the "U"-mode.     

Elemental analysis of airborne dust samples with TXRF: Comparison of oxygen-plasma ashing on sapphire carriers and acid digestion for sample preparation

The concentrations of 13 elements (As, Ca, Co, Cd, Cr, Fe, Ga, Ni, Pb, Pt, Ti, V and Zn) were determined in air particulate matter using total reflection X-ray fluorescence spectrometry (TXRF). For silicon analysis synthetic sapphire was chosen as a new sample carrier material – it is silicon-free, resistant to oxygen-plasma, microwaves and concentrated acids. The dust samples were collected on cellulose acetate filters. The decomposition of the filters was carried out by oxidation in a microwave-generated low-pressure oxygen-plasma directly on the TXRF sample carriers. The recovery of the investigated elements was verified with the standard reference material SRM 1648 (urban particulate matter) and ranged from 90 to 97%. The oxygen-plasma method was compared with conventional sample preparation by acid digestion. Received: 9 April 1999 / Revised: 18 May 1999 / Accepted: 3 June 1999     

Elemental analysis of airborne dust samples with TXRF: Comparison of oxygen-plasma ashing on sapphire carriers and acid digestion for sample preparation

The concentrations of 13 elements (As, Ca, Co, Cd, Cr, Fe, Ga, Ni, Pb, Pt, Ti, V and Zn) were determined in air particulate matter using total reflection X-ray fluorescence spectrometry (TXRF). For silicon analysis synthetic sapphire was chosen as a new sample carrier material – it is silicon-free, resistant to oxygen-plasma, microwaves and concentrated acids. The dust samples were collected on cellulose acetate filters. The decomposition of the filters was carried out by oxidation in a microwave-generated low-pressure oxygen-plasma directly on the TXRF sample carriers. The recovery of the investigated elements was verified with the standard reference material SRM 1648 (urban particulate matter) and ranged from 90 to 97%. The oxygen-plasma method was compared with conventional sample preparation by acid digestion. Received: 9 April 1999 / Revised: 18 May 1999 / Accepted: 3 June 1999     

Application of Leaching Tests for the Assessment of Available Heavy Metals from Domestic and Industrial Sludges

Various sludge samples from different domestic and industrial wastewater treatment plants were analyzed by Flame Atomic Absorption Spectrometry to evaluate their total and available contents of heavy metals (Cu, Cr, Ni, Pb, Zn and Fe). The EDTA and acetic acid single extraction procedures were applied to these samples with the aim to study the leaching behaviour of the metals in the different sludges and also to predict their possible mobility when these wastes are disposed on the environment and landfills. In acidic medium, a higher extraction efficiency was observed for the major part of the elements studied in the industrial sludges, except for Ni and Zn, which were also considerably released from domestic sludges. In contrast, in the presence of the EDTA complexing ligand, a more elevated mobility of metals was found in the domestic sludges and little or no metals were released from the industrial sludges. Moreover, the results of the microwave total digestions were compared, for all metals, with those obtained using a more simplified pseudototal digestion procedure (based on the EPA Method 3051, named microwave assisted acid digestion of sediments, sludges, soils and oils) and a good agreement was found between them, except for Cr and Ni in some particular samples. The between-batch precision (expressed as RSD) of both compared digestion methods was very similar and values lower than 7.7% were obtained in both cases. A certified domestic sludge material (SRM 2781) was employed to validate the two digestion procedures and no significant differences were found between the certified and experimental values for all the elements studied.     

The homogeneity of heavy metal deposition on glass fibre filters collected using a high-volume sampler in the vicinity of an opencast chrome mine complex at Kemi,Northern Finland

The homogeneity of heavy metal (Cr, Ni, Cu, Fe and Cd) distribution on glass fibre filters (Munktell MG 160, 203 x 254 mm, 75 g m(-2)) collected using a high-volume sampler (Wedding & Associates) at an opencast chrome mine complex at Kemi, Northern Finland was studied. The heavy metals in the total suspended particulate (TSP) material were analysed by inductively coupled plasma atomic emission spectrometry (ICP-AES) or graphite furnace atomic absorption spectrometry (GFAAS). The glass fibre filters were digested in a microwave oven using a mixture of aqua regia+HF acids. There was significant non-uniform distribution of heavy metals on glass fibre filters. The TSP material containing chromite was very difficult to dissolve by acid digestion. The results from X-ray fluorescence spectrometry (XRF), and from energy filtering transmission electron microscope (EFTEM) equipped with energy dispersive X-ray spectrometer (EDS), showed that insoluble residue left after microwave oven digestion with aqua regia+HF acids was probably partly due to chemical reactions occurring during microwave heating.     

Comparison of sample preparation methods for the ICP-AES determination of minor and major elements in clarified apple juices

Inductively coupled plasma atomic emission spectrometry (ICP-AES) was used for the determination of minor and major elements present in apple juices. Prior to ICP-AES measurement, samples were diluted with nitric acid or digested in a microwave assisted digestion system. The differences in the measured element concentrations after application of different types of sample preparation procedures are discussed. The direct measurement compared to closed microwave dissolution was found to be the best sample preparation procedure. Prior to the measurements the ICP-AES method was validated and optimized for the determination of elements in apple juices. For diluted apple juice samples the lowest limits of detection (LOD) were obtained for Ba and Cd (< 20 μg L^{− 1}), moderate ones for Cu, Mn, Ni, Fe, Ag, Ca, Cr, Zn, Mg, and Sr (20–100 μg L^{− 1}), and the highest LODs for K, Pb, Na, and Al (> 110 μg L^{− 1}). The results obtained for the repeatability (< 0.9%), the intermediate precision (< 4.5%), the day-to-day reproducibility (< 5.2%), and the overall uncertainty of measurement (approx. 4–7%) for all elements analyzed demonstrated the good applicability of the proposed method. Differences in major element content in fresh and commercial apple juice are discussed.     

模拟酸雨对土壤中铁、锰、锌的浸出特征

酸雨是指pH值小于5·6的大气降水,它不仅危害土壤,还通过土壤间接地危害整个生态系统,因此生态系统酸沉降的承受能力很大程度上取决于土壤对酸雨的敏感性〔1,2〕。我国能源以煤炭为主,大气中硫、氮含量较高,酸雨中SO42:-NO3-的比值范围大致在4:1到15:1之间〔3〕。同时,我国酸雨主要分布在长江以南地区,这正好与酸性土壤分布区相重叠,很大程度上加剧了对土壤的破坏程度。本文用ICP-AES法研究了在模拟酸雨作用下,土壤中生物必要元素Fe、Mn、Zn的释放水平和释放特征。1实验部分1.1仪器及工作条件电感耦合等离子体-原子发射光谱分析仪(IC…     

Major-to-ultratrace elements in bone-marrow fluid as determined by ICP-AES and ICP-MS.

The major-to-ultratrace elements in human bone-marrow fluid were determined by ICP-AES (inductively coupled plasma atomic emission spectrometry), and ICP-MS (inductively coupled plasma mass spectrometry). The bone-marrow fluid sample was centrifuged prior to acid digestion to exclude the bone piece from bone marrow, and then digested with nitric acid. As a result, 20 elements could be determined over the concentration range from 1610 microg g(-1) for Na to 0.00043 microg g(-1) for W. It was found that Fe, Zn and Sb were enriched by ca. 264-, 7- and 15-fold, respectively, in bone-marrow fluid, compared to those in human blood serum. Alkali metals (K, Rb, Cs), except for Na, were also significantly enriched in bone-marrow fluid. Furthermore, the concentrations of various elements, such as Fe, P, Al, Zn, Cu, Se, Zr, Sn, Ag and W, were significantly higher than those in open seawater.     

Comparative determination of Ba, Cu, Fe, Pb and Zn in tea leaves by slurry sampling electrothermal atomic absorption and liquid sampling inductively coupled plasma atomic emission spectrometry

The comparative determination of barium, copper, iron, lead and zinc in tea leaf samples by two atomic spectrometric techniques is reported. At first, slurry sampling electrothermal atomization atomic absorption spectrometry (ETAAS) was applied. The results of Ba and Pb determination were calculated using the method of standard additions, and results of Cu, Fe and Zn from the calibration graphs based on aqueous standards. These results were compared with the results obtained after microwave-assisted wet (nitric+hydrochloric+hydrofluoric acids) digestion in closed vessels followed by inductively coupled plasma-atomic emission spectrometric (ICP-AES) determination with the calibration by means of aqueous standards. The exception was lead determined after a wet digestion procedure by ETAAS. The accuracy of the studied methods was checked by the use of the certified reference material Tea GBW-07605. The recoveries of the analytes varied in the range from 91 to 99% for slurry sampling ETAAS, and from 92.5 to 102% for liquid sampling ICP-AES. The advantages of slurry sampling ETAAS method are simplicity of sample preparation and very good sensitivity. Slurry sampling ETAAS method is relatively fast but if several elements must be determined in one sample, the time of the whole microwave-assisted digestion procedure and ICP-AES determination will be shorter. However, worse detection limits of ICP-AES must also be taken into the consideration in a case of some analytes.     

Determination of Al,B and 11 Other Trace Elements in Plants by Inductively Coupled Plasma-Atomic Emission Spectrometry:Comparison of Five Different Sample Digestion Procedures

For accurate determination of nutritional and toxic elements in plants by means of inductively coupled plasma atomic emission spectrometry (ICP-AES), sample preparation is a critical phase. Although some procedures such as dry ashing in a muffle furnace or wet digestion with HN0₃-HC10₄ on a hot plate have been available for many years, growing interest has been focused on the use of microwave-based digestion in recent years. Compared to the classical digesting procedures, microwave digestion has some significant advantages:the digestion is carried out in closed vessels so that the contamination and the loss of volatile elements are markedly minimized; the digestion is less time consuming due to the elevated pressure and temperature within the vessels. In addition, the use of polytetrafluoroethylene (PTFE) vessels for microwave digestion makes it both easy and safe to employ very corrosive reagents, such as HF.     

Distributions of major-to-ultratrace elements among the particulate and dissolved fractions in natural water as studied by ICP-AES and ICP-MS after sequential fractionation.

In order to elucidate the distributions of the elements among the particulate and dissolved fractions in pond water, major-to-ultratrace elements in different sizes of particles as well as in the filtrate passed through the 0.05 microm filter were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). The different sizes of particle samples (ca. 100-300 microg each) were collected on the membrane filters with pore sizes of 10, 3.0, 1.2, 0.4, 0.2 and 0.05 microm, respectively, by sequential fractionation. As a result, about 40 elements in different sizes of particles could be determined by ICP-AES and ICP-MS, after acid digestion using HNO3/HF/HClO4. Then, the fractional distribution factors of major-to-ultratrace elements among the particulate and dissolved fractions were estimated from the analytical results. The total contents of Al, Fe, Ti, REEs (rare earth elements), Bi, Pb and Ag in the particulate fractions (larger than 0.05 microm) were more than 80-90%, while those of Ca, Sr, Cs, W, Ba, Mn and Co in the dissolved fraction, which corresponded to the filtrate passed through the 0.05 microm membrane filter, were more than 80%. It was further found that the fractional distributions of Cu and Zn in the dissolved fraction were ca. 50%. In addition, the enrichment factors (EFs) of the elements in the particulate fractions with particle sizes of 3.0-10 microm and 0.05-0.2 microm were estimated to elucidate their geochemical characteristics in natural water.     

Rapid dissolution of large environmental samples for the determination of fission products

The dissolution of large environmental samples was investigated using a microwave autoclave, capable of digestion conditions of 300 °C and 200 bar, for the application of rapid determination of radionuclides. Six samples of up to 5 g plant material were digested, also eliminating predigestion steps such as ashing and grinding. Batches of forty 1 g samples of plant leaves were also completely digested in 75 minutes. Quantitative recovery of ⁹⁰Sr from 5 g soil samples by leaching with 8M HNO₃ at 200 °C was achieved, whereas ¹³⁷Cs was not completely recovered from the large soil samples using total digestion or leaching (HCl:HNO₃) techniques, but quantitative recovery was achieved using fusion and sinter procedures.