Kinetics of formation,dissociation and equilibrium constants of pentacyanoaquoruthenate(II) with heterocycles

The kinetics of formation and dissociation reactions of [Ru(CN)₅L]^3– with a series of heterocyclic ligands were studied in aqueous media. In this presence of an excess of heterocycle, the observed second order rate constants were calculated from the k_obs versus [ligand] plot at =0.100m NaClO₄. Activation parameters for the formation reactions (H=28±7kJmol^–1 and S=140±35JK^–1mol^–1) are comparable for all systems, indicating a common mechanism. The kinetics of exchange of coordinated heterocycles for 1,3,5-triazine yielded a rate saturation typical of a limiting dissociative mechanism. Activation parameters of the limiting first order specific rate of dissociation reactions were H=85±7kJmol^–1 and S=18±4JK^–1mol^–1. Equilibrium constants were calculated from the second order rates of formation and pseudo-first order rates of dissociation reaction.     

Determination of Attogram Quantities of Silver via Quenching of the Solid Substrate Room-Temperature Phosphorescence of Rhodamine B Based on the Catalysis of its Oxidation by Potassium Persulfate

A new method of SS-RTP for the determination of trace silver has been established. This method is based on the fact that Ag⁺, when activated by ,-bipyridyl (bipy) in a media of HAc–NaAc (pH=4.9), can catalyze the reaction of Rhodamine B (RhoB) oxidized by K₂S₂O₈, thus causing the Solid Substrate Room-Temperature Phosphorescence (SS-RTP) of RhoB to be quenched. The activating efficiency of bipy is 6.7 times higher than that of o-phenanthroline (phen). The reduction of the phosphorescence intensity (I_p) of RhoB is directly proportional to the concentration of Ag⁺ ions in the range of 1.6016.0agspot^–1 (0.40µLspot^–1). The regression equation of the working curve can be expressed as I_p=18.78+5.100m_Ag+ (agspot^–1) (r=0.9994, n=6), the detection limit is 0.28agspot^–1. This rapid, accurate and sensitive method has been successfully applied to the determination of trace silver in tea and human hair samples, and the results agree well with the Atomic Absorption Spectroscopy (AAS) method. The mechanism of the catalyzing reaction is also discussed.     

Electrochemical Determination of 4-Nitrophenol Using a Single-Wall Carbon Nanotube Film-Coated Glassy Carbon Electrode

A single-wall carbon nanotubes (SWNT) film coated glassy carbon electrode (GCE) was fabricated for the direct determination of 4-nitrophenol (4-NP). The electrochemical behaviors of 4-NP at the SWNT-film coated GCE were examined. In 0.1M phosphate buffer with a pH of 5.0, 4-NP yields a very sensitive and well-defined reduction peak at the SWNT-modified GCE. It is found that the SWNT film exhibits obvious electrocatalytic activity towards the reduction of 4-NP since it not only increases the reduction peak current but also lowers the reduction overpotential. Based on this, an electrochemical method was proposed for the direct determination of 4-NP. The reduction peak current varies linearly with the concentration of 4-NP ranging from 1×10^–8 to 5×10^–6M, and the detection limit is 2.5×10^–9M after 3min of open-circuit accumulation. The relative standard deviation at 2×10^–7M 4-NP was about 6% (n=10), suggesting excellent reproducibility. This new method was successfully employed to determine 4-NP in several lake water samples.     

Solid-Phase Extraction with Slurry Injection of the Resin Into ETAAS for Trace Determination of Thallium in Natural Water

Thallium in natural water samples was determined by electrothermal atomic absorption spectrometry after 1000-fold enrichment by mini solid-phase extraction from a 100-mL sample solution. A Tl-pyrrolidine-1-carbodithioate complex formed in a sample solution of pH 1.6 was extracted on fine particles of a cellulose nitrate resin dispersed in the sample solution. The cellulose nitrate resin was then collected on a membrane filter (25mm^ø) by filtration under suction using a glass funnel with an effective filtration area of 0.64cm². As a result, a circular thin layer of the resin phase with a diameter of 9mm was obtained. Then the resin phase was carved out by an acrylate resin puncher with a 10-mm^ø hole to put it into a sample cup containing 100µL of 10mM HNO₃ containing 0.5mM NaCl. The resin phase was suspended in the solution by ultrasonication. 1000-fold enrichment was thus attained within 15min, and the suspension was delivered to electrothermal atomic absorption spectrometry. The linear calibration graph was obtained in the range of 0–4ng of Tl in 100mL of a sample solution. The detection limit obtained by 3 method was 0.19ng. The proposed method was applied to the determination of Tl in natural water samples. The results showed the concentration of Tl in seawater was 12.1±1.8pgmL^–1 for the calibration graph method and 12.6±1.4pgmL^–1 for the standard addition method. A snowmelt sample contained 20.7±1.0pgmL^–1 of Tl.     

Determination of Heavy Metal Ions in Chinese Herbal Medicine by Microwave Digestion and RP-HPLC with UV-Vis Detection

A new method for the simultaneous determination of heavy metal ions in Chinese herbal medicine by microwave digestion and reversed-phase high-performance liquid chromatography (RP-HPLC) has been developed. The Chinese herbal medicine samples were digested by microwave digestion. Lead, cadmium, mercury, nickel, copper, zinc, and tin ions in the digested samples were pre-column derivatized with tetra-(4-chlorophenyl)-porphyrin (T₄-CPP) to form the colored chelates which were then enriched by solid phase extraction with C₁₈ cartridge and eluted from the cartridge with tetrahydrofuran (THF). The chelates were separated on a Waters Xterra RP₁₈ column by gradient elution with methanol (containing 0.05molL^–1 pyrrolidine-acetic acid buffer salt, pH=10.0) and THF (containing 0.05molL^–1 pyrrolidine-acetic acid buffer salt, pH=10.0) as mobile phase at a flow rate of 0.5mLmin^–1 and detected with a photodiode array detector in the range of 350–600nm. In the original samples the detection limits of lead, cadmium, mercury, nickel, copper, zinc and tin are 4ngL^–1, 3ngL^–1, 6ngL^–1, 5ngL^–1, 2ngL^–1, 6ngL^–1, and 4ngL^–1, respectively. This method was applied to the determination of lead, cadmium, mercury, nickel, copper, zinc and tin in Chinese herbal medicine samples with good results.     

Flame Atomic Absorption Spectrometric Determination of Gold and Palladium Using Microcolumn On-line Preconcentration and Separation

A microcolumn on-line preconcentration and separation system was developed for the flame atomic absorption spectrometric (FAAS) determination of trace levels of gold and palladium. The analytes were selectively adsorbed onto the microcolumn packed with 2-mercaptothiazole immobilized silica gel (MBTSG) in an acidity range of 0.1 to 6.0M HCl at a sampling flow rate of 4.0mLmin^–1. The analytes adsorbed could be desorbed by a thiourea solution with a flow rate of 2.0mLmin^–1. Most of the common coexisting metal ions at a concentration of 25.0mgmL^–1 and anions at a concentration of 50.0mgmL^–1 did not interfere with the preconcentration and determination of Au and Pd. The limits of detection (LOD), defined as three times the standard deviation of the blank (3), of Au and Pd are 10ngmL^–1 and 26ngmL^–1, respectively, with a preconcentration time of 60s. The relative standard deviation (RSD) is about 2.0% for 0.20µgmL^–1 Au and 0.30µgmL^–1 Pd. With a sample loading time of 30min, 6.7ngmL^–1 Au and 10ngmL^–1 Pd can be preconcentrated quantitatively. A geological sample, an anode slime and a secondary nickel alloy were successfully determined with the proposed method, and the results obtained showed good agreement with the certified values.Received December 23, 2002; accepted May 14, 2003 Published online August 8, 2003     

Voltammetric Behavior of Dopamine at ct-DNA Modified Carbon Fiber Microelectrode

A sub-micrometer thin-layer DNA modified carbon fiber microcylinder electrode was prepared by electrodeposition of ct-DNA at 1.5V (vs. Ag/AgCl). The voltammetric behavior of dopamine (3-hydroxytyramine) was investigated at the modified electrode. It was found that the modified electrode exhibits a highly electrocatalytic activity toward dopamine oxidation. Differential pulse voltammetry was used for determination of dopamine in pH 7.4 phosphate buffer solution. A linear response of the peak current versus the concentration was found in the range of 4×10^–6 to 10^–4molL^–1 at 10^–4molL^–1 AA (ascorbic acid) coexistence (R=0.9959) and the range of 6×10^–5 to 10^–3molL^–1 at 10^–3molL^–1 AA (R=0.9960). The presence of a high concentration of ascorbic acid did not interfere with the determination. The proposed method exhibited good recovery and reproducibility. This method can be applied to the detection of DA in real samples.     

Adsorptive Catalytic Voltammetry of Physcion in the Presence of Dissolved Oxygen at a Carbon Paste Electrode

A novel electroanalytical method for the determination of physcion is described for the first time. Physcion yields an adsorption catalytic voltammetric peak at –0.74V (vs. SCE) in 0.4molL^–1 NH₄Cl–NH₃·H₂O buffer solution (pH 10.5) at a carbon paste electrode (CPE). The experimental results indicated that physcion is efficiently accumulated at a CPE by adsorption. In the subsequent potential scan, physcion was reduced to a homologous anthrahydroquinone compound. The compound was then immediately oxidized to physcion by the dissolved oxygen in the solution, and then physcion was again reduced at the CPE. As a result, a cyclic catalytic reaction was established. The second-order derivative peak current is proportional to the physcion concentration in the ranges of 2.0×10^–104.0×10^–9molL^–1 (accumulation 90s) and 4.0×10^–92.0×10^–8molL^–1 (accumulation 60s). The limit of detection is 8×10^–11molL^–1 (S/N=3) for a 120s accumulation time. The method was applied to the direct determination of physcion in the medicinal plant polygonum multiflorum Thumb with satisfactory results.     

The Electrochemical Behavior of p-Aminophenol at a ω-Mercaptopropionic Acid Self-Assembled Gold Electrode

A -mercaptopropionic acid (MPA) self-assembled monolayer modified electrode (MPA/SAM/Au) on a gold electrode has been fabricated. The characterization of the MPA/SAM/Au was investigated using attenuated total reflection-fourier transform infrared (ATR-FTIR) and A.C. impedance. The electrochemical behaviors of p-aminophenol (p-AP) were studied at the MPA/SAM/Au by cyclic voltammetry and semi-derivative voltammetry (SDV) in BR buffer solution. The modified electrode shows excellent electrocatalytic activity for the redox of p-AP and accelerates the electron transfer rate. The diffusion coefficient (D) is 4.55×10^–6cm²s^–1. The oxidative peak current increases linearly with the concentration of p-AP in the range of 4.0×10^–88×10^–6molL^–1 and 1.0×10^–52×10^–4molL^–1 by square wave voltammetry response, respectively. The detection limit (three times the signal blank/slope) is up to 1.2×10^–8molL^–1. The modified electrode is able to eliminate the interference of p-benzenediol, o-benzenediol and o-AP at a 40-, 90- or 70-fold concentration of p-AP, and it has been satisfactorily used for the determination of the real sample.     

Determination of Caffeine Using a Simple Graphite Pencil Electrode with Square-Wave Anodic Stripping Voltammetry

A simple commercial graphite pencil electrode (GPE) was utilized for monitoring caffeine using the square-wave anodic stripping voltammetry (SWASV) method. This method was applied to determine the caffeine levels in several tea samples, which yielded a relative error of 1% in the concentrations. Caffeine was deposited at 0.0V (vs. Ag/AgCl), then reduced at +1.40V to strip it on the GPE. Optimal experimental conditions for the analysis were found to be as follows: pH value of 9 for the medium; deposition potential of 0.0V; deposition time of 120s; SW frequency of 25Hz; SW amplitude of 45mV, and step potential of 6mV. Given these optimum conditions, a linear range was observed within the concentration of 0500mgL^–1. At caffeine concentrations of 50.0, 250.0, and 500.0mgL^–1, the relative standard deviations in measured concentrations (n=12) were 0.19, 0.09, and 0.11%, respectively. The detection limit was found to be 9.2mgL^–1, which is comparable with the result obtained using a carbon paste electrode, equivalent to 8.2mgL^–1.     

Development of an FI-ICP Method for On-Line Preconcentration and Determination of Platinum

This paper presents a new simple and rapid procedure for the preconcentration and determination of platinum. It is based on the adsorption of the metal ion and preconcentration on a micro-column (3cm×3mm) placed in the injection valve of a flow injection (FI) manifold and packed with 1,5-bis[(2-pyridyl)-3-sulphophenyl-methylene]thiocarbonohydrazide (PSTH) immobilised on an anion-exchange resin (Dowex 1X8-200). The metal was eluted from the column using a solution of 2M HNO₃. Various parameters and chemical variables affecting the preconcentration and determination of this metal by ICP-AES were evaluated. Five variables (sample flow rate, eluent flow rate, nebulizer flow rate, buffer concentration and mixing coil length) were considered as factors in the optimisation process. Interactions between analytical factors, and their optimal levels were investigated using two level factorial and central matrix designs. The optimum conditions established were applied to the determination of platinum by flow injection inductively coupled plasma atomic emission spectrometry (FI-ICP-AES). The method has a linear calibration range of 25 to at least 200ngmL^–1 with a detection limit of 7.4ngmL^–1 (S/N=3) and a throughput of 10 samples h^–1 using 5min. preconcentration time. The precision of the method (RSD) was 3.06% ngmL^–1 at the 50ngmL^–1 level of Pt(IV) and 2.93% at the 150ngmL^–1 level. The accuracy of the method was examined by determining the analyte content in spiked waters and by analysing an automobile catalyst standard reference material. The results show good agreement with the certified value and sufficiently high recoveries.     

Determination of Lead Using a New Chromogenic Reagent 2-(2-Sulfo-4-acetylphenylazo)-7-(2,4,6-trichlorophenylazo)-1,8-dihydroxynaphthalene-3,6-disulfonic Acid

A novel chromogenic reagent, 2-(2-sulfo-4-acetylphenylazo)-7-(2,4,6-trichlorophenylazo)-1,8-dihydroxynaphthalene-3,6-disulfonic acid 1, was prepared by diazo coupling of 4-acetylaniline-2-sulfonic acid and 2,4,6-trichloroaniline to chromotropic acid through –N=N– groups. Based on this reagent, a simple, sensitive and selective spectrophotometric method was developed for the determination of lead. In 0.20M phosphoric acid medium, lead reacts with 1 to form a 1:2 blue complex with an absorption maximum of 654nm. Beers law is obeyed in the range of 0–0.6mgL^–1 of lead. The apparent molar absorptivity is 1.25×10⁵Lmol^–1cm^–1. The detection limit and quantification limit were found to be 0.63µgL^–1 and 2.1µgL^–1, respectively. The relative standard deviation for eleven replicate measurements was of 2.6%. The interference of foreign ions was also investigated. All the other foreign ions studied did not interfere with lead determination except for Ca(II) and Ba(II). The interference caused by Ca(II) and Ba(II) can be eliminated by prior extraction of lead with potassium iodide-methylisobutylketone (KI-MIBK). The proposed method was applied to the determination of lead in certified samples with satisfactory results.     

Solid-Phase Extraction and Spectrophotometric Determination of Trace Amounts of Mercury in Natural Samples

A sensitive and selective solid phase spectrophotometric method for the determination of trace amounts of inorganic mercury is described. Hg²⁺ was sorbed on a silica gel-packed column as an Hg²⁺–N,N-bis(2-mercaptophenyl)ethanediamide (H₂L) complex. The Hg²⁺ complex was eluted from the column using 7mL of acetone. Various parameters including pH, column flow rate, and ligand concentration were optimized. The complex was found to obey Beers law from 2.3 to 73.7µgmL^–1 within the optimum range when the preconcentration factor was two. The effective molar absorption coefficient at 523nm was 1.17×10³Lmol^–1cm^–1 at 523nm. The concentration limits in Beers law dropped from 0.09 to 2.95µgmL^–1 within the optimum range when the preconcentration factor was 50. The relative standard deviation at a concentration level of 5µgmL^–1 Hg²⁺ (9 repetitive determinations) was 1.6%. The detection limits are 0.34µgmL^–1 and 0.015µgmL^–1 when the preconcentration factors are 2 and 50, respectively. The method has been used for routine determination of trace levels of Hg²⁺ in natural waters. The potential application of this method for the removal of Hg²⁺ from natural samples (sea water and lake water) spiked with 100ngmL^–1 of Hg²⁺ was studied. In order to validate the proposed method, LGC 6156 (harbour sediment – extractable metals) was analysed by this method. The results proved that excellent extraction of Hg²⁺ from both natural water samples was obtained by solid phase extraction using N,N-bis(2-mercaptophenyl) ethanediamide.     

Determination of Arsenic in Food Samples by Hydride Generation – Atomic Absorption Spectrometry

A method for the determination of trace amounts of arsenic in food samples using flow injection analysis and atomic absorption spectrometry with hydride generation (FI-HG AAS) was developed. The parameters of the flow injection system and the hydride generation were optimized with respect to reagent concentrations, atomization temperature, injection volume, reaction coil length and carrier flow rate. The limits of detection and quantification were 0.34µgL^–1 and 1.2µgL^–:1, respectively, and the analytical curve is linear up to 30.0µgL^–1 arsenic. The relative standard deviation for 12 replicates varies between 5% for 4.0µgL^–1 As and 1.8% for 30.0µgL^–1 As, with an injection frequency of up to 135h^–1. Interferences from Ni(II), Cu(II), Fe(III), Cr(III), Mo(II), Bi(III), Se(IV), Se(VI), Sb(III) and Sb(V) could be masked with a mixture of ascorbic acid-KI in a 5.0molL^–1 HCl solution. The accuracy of the proposed method was evaluated by using certified reference materials of biological samples, and the method was used to determine the content of arsenic in fish and coffee beans.     

A Simple Sensitive Spectrophotometric Method for the Determination of Ce4+ Using Variamine Blue as a Chromogenic Reagent

A rapid and sensitive spectrophotometric method is described for the determination of trace amounts of cerium using Variamine Blue (VB) as a chromogenic reagent. The proposed method is based on the reaction of cerium with potassium iodide in acidic medium to liberate iodine, which oxidizes Variamine Blue to give a violet colored species with an absorption maximum at 560nm. Beers law was obeyed in the range 2–10µg mL^–1 of cerium. The molar absorptivity and Sandells sensitivity are found to be 1.65×10⁴L mol^–1cm^–1 and 8.48×10^–3µgcm^–2, respectively. The proposed method has been successfully applied to the determination of cerium in alloy and synthetic mixtures.     

Novel tetrahedral and heteronuclear transition metal clusters prepared via single and double isolobal displacements

Ten transition metal cluster complexes with parent and substituted cyclopentadienyl ligands, [(⁵-C₅H⁴ CH₂CH₂)₂O][MFeCoS(CO)₈]₂ (2 M=Mo; 3 M=W), (⁵-C₅H₅)(⁵-RC₅H₄)MFeNiS(CO)₅ (5 M=Mo, R=Me; 6M= W, R=H), (⁵-C₅H₅)[⁵-C₅H₄C(O)CH₂]₂[WFeNiS(CO)₅][WFeCoS(CO)₈] (8), (⁵-C₅H₅)₂[⁵-C₅H₄ C(O)CH₂]₂[WFeNiS(CO)₅]₂ (9), (⁵-RC₅H₄)[(⁵-C₅H₄CH₂CH₂)₂O][Mo2FeS(CO)₇][MoFeCoS (CO)₈] (10R=MeCO; 12 R=MeO2C), (⁵-RC₅H₄)₂[(⁵-C₅H₄CH₂CH₂)₂O][Mo₂FeS(CO)₇]₂ (11 R=MeCO; 13 R=MeO2C), were synthesized through single and double isolobal displacements and characterized by elemental analyses, i.r., 1H-n.m.r. and MS techniques.     

Structural studies and diffusion measurements of water-swollen cellophane by NMR imaging

NMR imaging and spatially resolved diffusometry have been used to study the distribution of water within swollen cellophane and measure its diffusion coefficient. Water concentration and diffusion coefficient were found to be essentially constant across most of the film thickness. However, significantly slower diffusion was indicated for water near the film surface (D=0.5×10^–9m²s^–1) compared with water in the centre of the film (D=0.88×10^–9m²s^–1). This was also reflected in lower T ₂ values at the edge of the film indicating water with more restricted motion. These observations were interpreted in terms of dense surface regions of cellulose (skin) over a more porous interior (core).     

Rapid and Simple Determination of a Cationic Surfactant by Adsorption Induced by Vigorous Shaking

A rapid and simple method for the determination of a cationic surfactant is described. The method is based on the formation of an ion associate with tetraphenylporphinetetrasulfonic acid (TPPS) and zephiramine as an example of a cationic surfactant. The ion associate was adsorbed on the inner wall of the vessel by vigorous shaking. After complete removal of the solution in the tube, the ion associate was dissolved with 50% ethanol and measured spectrophotometrically. The proposed method is simple and rapid. The apparent molar absorption coefficient for zephiramine using 20mL of sample and 5mL of eluent was estimated to be 9.01×10⁴Lmol^–1cm^–1 at 415nm. The coefficient of variation for 20.2µg of zephiramine was 5.9% (n=10).     

Determination of Trace Proteins by Rayleigh Light Scattering Technique with Indophenol Blue

The interaction of indophenol blue (IPB) with proteins in aqueous solution has been studied by optical absorption and Rayleigh light scattering (RLS) spectroscopy. At pH 3.8, the weak RLS of IPB is enhanced by proteins. Based on this phenomenon, a novel method for the determination of proteins at nanogram levels using the RLS technique is developed. The method is simple, practical and sensitive. The linear range is 0.25–20.9µgmL^–1 for BSA, and 0.25–17.6µgmL^–1 for HSA. The detection limits (S/N=3) are 23ngmL^–1 for BSA and 22ngmL^–1 for HAS. The results for the determination of proteins in human serum samples are very close to those obtained by an established clinical method. There is very little interference from amino acids, metal ions or other coexisting compounds.     

Determination of Iron in Tap and Waste Water Using Liquid–Liquid Extraction in a Flow-Injection System

A flow-injection procedure for the determination of iron(III) in water is described. The procedure is based on the formation of an ion pair between the tetraphenylarsonium (Ph₄As⁺) (TPA) or tetrabutylammonium (But₄N⁺) (TBA) cations and the tetrathiocyanatoferrate(III) complex (TTF). This ion pair is extracted with chloroform, and the absorbance of the organic phase is measured at 503nm (for Ph₄As⁺) or 475nm (for But₄N⁺). Iron concentrations higher than 0.9×10^–6molL^–1 (50µgL^–1) can be detected in the first case, with a relative standard deviation of 1.9% (n=12), a linear application rangeof between 1.34 and 54.0×10^–6molL^–1 (75–3015µgL^–1), and a sampling frequency of 30h^–1. For the ion pair with But₄N⁺, the detection limit is 0.52×10^–6molL^–1 (29µgL^–1), with a relative standard deviation of 1.6% and a linear application range between 0.73 and 54.0×10^–6molL^–1. Under the proposed working conditions, only Pd(IV), Cu(II) and Bi(III) interfere. With the application of the merging zones technique, considerable amounts of organic reagent can be saved. The TBA method was applied to the analysis of iron(III) in tap and industrial waste waters.