Sodium salts of sulfonated poly(phenylene ethers) as polysoaps

Polysoaps are of interest because, unlike most polyelectrolytes, their aqueous solutions become more viscous and often form gels upon the addition of salt. A new kind of polysoap was made by sulfonating phenylene oxide polymers that have a pendant alkyl group containing at least 14 carbon atoms on every phenylene unit. Copolymers made from a mixture of 2,6-dimethylphenol and 2-methyl-6-tetradecylphenol have the same composition as the monomer mixture. Tetradecyl substituents in the copolymer act as internal plasticizing agents and, by varying the number of substituents, a gradation in physical properties of the unsulfonated copolymer from rigid solid to heavy oil is possible.     

Aqueous solution behavior of alkali-soluble polyethylene periodic polyelectrolyte, poly(ethylene- per-ethylene-per-acrylic acid)

A sequence-ordered, periodic copolymer of ethylene, ethylene, and acrylic acid, poly (ethylene-per-ethylene-per-acrylic acid) (PEEA), with M _w=1.44×10⁵ has been synthesized by alternating copolymerization of 1,3-butadiene and methyl acrylate, followed by hydrogenation and hydrolysis. Aqueous solution and dissociation properties of the alkali-soluble PEEA were explored by potentiometric titration and intrinsic viscosity at 25 °C. The pH values of PEEA were almost constant (pH = 6.48 ∼ 6.55) with an increasing degree of dissociation (α) from 0.3 to 0.8 at C _s=50 mN NaCl. Correspondingly, the plots of negative logarithm of apparent dissociation constant (pK _a) against α showed a reversed S-shape curve over the whole α, indicating an extensive precipitation and subsequent tran-sition from compact to coiled conformation. The intrinsic viscosity steeply increased with α above 0.4 up to 9.97 dl/g at α = 1.0. Good agreement between the observed electrostatic potential and that calculated from the rod model with a smeared charge density was observed in the region of α higher than 0.9. The dissociation and dissolution processes of PEEA with neutralization in water were described. Received: 14 April 1998 Accepted: 3 June 1998     

Mixed self-assembly of poly(ethylene oxide)-b-poly(epsilon-caprolactone) copolymers and sodium dodecyl sulfate in aqueous solution

Interaction of amphiphilic poly(ethylene oxide)-b-poly(epsilon-caprolactone) copolymers with anionic sodium dodecyl sulfate (SDS) has been investigated in aqueous solution. Formation of mixed micelles has been confirmed by surface tension measurements, whereas the influence of the surfactant on the copolymer self-assembling has been studied by measurement of the 1H NMR self-diffusion coefficients and by small-angle neutron scattering. As a rule, the surfactant decreases the heterogeneity of the micellar structures formed by the copolymer in water. Moreover, increasing the content of SDS results in the increasingly more important extension of the poly(ethylene oxide) (PEO) corona chains and the copolymer micelle deaggregation. The stability of the micelles against SDS increases with the length of the hydrophobic block. Preliminary two-dimensional NMR measurements with nuclear Overhauser enhancement have confirmed the spatial vicinity between SDS and the constitutive blocks of the copolymer.     

Assembly of poly(N-isopropylacrylamide)-co-acrylic acid microgel thin films on polyelectrolyte multilayers: Effects of polyelectrolyte layer thickness, surface charge, and microgel solution pH

Temperature- and pH-sensitive poly(N-isopropylacrylamide)?Cco-acrylic acid (pNIPAm-co-AAc) microgels were deposited on glass substrates coated with polyelectrolyte multilayers composed of the polycation poly(allylamine hydrochloride) (PAH) and the polyanion poly(sodium 4-styrenesulfonate) (PSS). The microgel density and structure of the resultant films were investigated as a function of: (1) the number of PAH/PSS layers (layer thickness); (2) the charge on the outer layer of the polyelectrolyte multilayer film; and (3) the pH of microgel deposition solution. The resultant films were studied by differential interference contrast optical microscopy, atomic force microscopy, and scanning electron microscopy. It was found that the coverage of the microgels on the surface was a complex function of the pH of the deposition solution, the charge on the outer layer of the polyelectrolyte thin film and the PAH/PSS layer thickness; although it appears that microgel charge plays the biggest role in determining the resultant surface coverage.     

Solution behavior of progressively quaternized poly(dimethylaminoethyl methacrylate) as a function of charge density

Hydrodynamic behavior of progressively quaternized poly(dimethylaminoethyl methacrylate) (PDMAEM) in dilute and semi-dilute salt–free aqueous solutions as a function of molar mass and charge density, which varied from 5 up to 100 mol%, was studied. The role of long range electrostatic interactions on the viscosity and on the position and value of the reduced viscosity corresponding to the peak, η_red,p, as a function of the charge density of polycation has been evaluated. The overlap concentration of polyelectrolytes, c^∗, has been evaluated as the inverse of the intrinsic viscosity determined by fitting the viscometric results on Rao equation. The values of c^∗ have been discussed as a function of polyion molar mass and charge density. The c^∗ values calculated in the frame of Odijk model for polyelectrolytes having quaternization degree ?50 were lower but comparable with those determined by viscometry, for the same molar mass.     

聚苯醚磺酸锂与聚醋酸乙烯酯共混物的导电性能研究

为改善聚苯醚磺酸锂（SPPOLi）的导电性能，将聚酷酸乙烯酯（PVAc）与之共混，X-射线衍射分析表明，PVAc可降低SPPOLi凝聚结构的有序程度；发现共混后电导率有了较大提高，共混物的电导对温度的依赖关系不符合阿仑尼马斯方程；同时，共混物仍保持了单离子传导性．     

Swelling behavior and solubility parameter of sulfonated poly(ether ether ketone)

The solubility parameter of sulfonated poly(ether ether ketone) (SPEEK) was investigated. SPEEK exhibited two solubility parameters, 26.4 and 35.7 J^1/2 cm^?3/2, and was similar in that respect to Nafion, which has two cohesive energy densities. The theoretical solubility parameter of SPEEK, 26.1 J^1/2 cm^?3/2, was determined with van Krevelen's method and corresponded to the experimental value. The theoretical volume fraction of SPEEK in the solvent was determined with Flory's equation. The trend of the theoretical volume fraction of SPEEK fit quite well with the experimental results when the solubility parameter of the solvent was lower than 35 J^1/2 cm^?3/2. A significant deviation of the experimental volume fraction of SPEEK with the high solubility parameter resulted from the presence of sulfonic acid groups. SPEEK in the sodium form exhibited similar solvent absorption in comparison with SPEEK in the acid form. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3128–3134, 2006     

Dynamics and energetics of the self-assembly of a hydrophobically modified polyelectrolyte: Naphthalene-labeled poly(acrylic acid)

Steady-state and time-resolved fluorescence studies were performed on aqueous solutions of poly(acrylic acid) hydrophobically modified with two very different levels of naphthalene (Np). It is demonstrated that unique information on association phenomena involving hydrophobe-modifed polymers can be obtained from an extended fluorescence study by using data for a less-modified polymer as a reference. For the more highly modified polymer, the presence of excited-state (as well as ground-state) dimers in addition to monomer emission due to locally excited naphthalene gives evidence for hydrophobic association between naphthalene groups. This association becomes, as expected, much less important at higher pH due to the electrostatic repulsion between different chain segments. However, it is noted that even at high pH there is a significant self-association. The coexistence of static and dynamic quenching phenomena of the Np monomer label was also revealed in the time-resolved fluorescence data. The data are compatible with the existence of two types of monomers and one excimer and suggest that the essential contribution to the monomer emission comes from isolated chromophores, whereas excimer formation arises from both a dynamic route (excited Np chromophores able to produce a dynamic excimer) and a static route (excitation of ground-state Np dimers). At room temperature, the dissociative reaction, excimer-to-monomer, can be neglected, and thus the rate constant for excimer formation and decay could be obtained with and without considering the influence of preformed dimers. Temperature has shown to induce different behavior in the polymer photophysics. In the case of the less-labeled polymer, the decays were found to be single-exponential with the fluorescence lifetime decreasing with increasing temperature. From the temperature dependence of the steady-state fluorescence data, the activation energy for excimer formation and the binding energy of the excimer were evaluated at different pH values, through the Stevens-Ban-type plots of the excimer-to-monomer intensity ratio. With the time-resolved data, measured in the temperature range of 5-60 degrees C, it was possible to extract the intrinsic activation energies for excimer formation. The thermodynamic driving force for the intrapolymeric association was found to be dependent on a balance between hydrophobic and electrostatic interactions, which are dependent on the pH, temperature, and hydrophobic content of the polymer.     

Equilibrium behavior and dilational rheology of polyelectrolyte/insoluble surfactant adsorption films: didodecyldimethylammonium bromide and sodium poly(styrenesulfonate)

The surface pressure of monolayers of an insoluble surfactant, didodecyldimethylammonium bromide (DODAB), has been measured onto subphases with different concentrations of poly(styrenesulfonate) (PSS) and at different temperatures. The presence of PSS in the subphase shifts the surface-pressure (Pi) curves to larger areas per DODAB molecule, A, and shifts the surface phase transition to higher Pi's. The presence of PSS chains decreases the surface electric potential; the decrease is higher than expected from the formation of a double layer between the DODAB molecules and the PSS segments. Increasing the temperature shifts the surface-pressure curves to higher areas and also increases the values of Pi of the surface phase transition. The effect of the PSS chains on the Pi versus A curves is contrary to the one induced by the presence of inert electrolytes in the subphase. The behavior is consistent with the existence of a dense layer of PSS segments beneath the DODAB monolayer at low PSS concentrations, c. Two PSS layers exist at higher concentrations, a dense layer immediately below the DODAB and a less-dense layer, below the first one, that protrudes deep into the subphase. The surface-pressure relaxation curves have been found to be bimodal through the whole range of surface pressures and at all the values of polymer concentration studied. These results point out that the adsorption layers behave mainly as elastic bodies, with zero-frequency elasticity, epsilon(omega = 0), which agrees with the equilibrium compressibility modulus. The increase [epsilon(omega = 1) - epsilon(omega = 0)] has been found to be independent of both polymer concentration and molecular weight. The zero-frequency-dilational viscosity, kappa(omega = 0), strongly increases with Pi in the two-dimensional condensed-liquid region. The surface viscosity strongly decreases with increasing frequency; the decreasing rate is higher than the one found for the monolayers of nonionic insoluble polymers. kappa(omega = 0) has also been found to be independent of both polymer concentration and molecular weight. These results seem to indicate that it is the film formed by the DODAB molecules and the first dense polymer layer that determines the surface viscoelastic moduli of this system.     

Modification of poly(vinyl chloride) with sodium salts of triazoles

New copolymers containing reactive vinyltriazole units and polyvinylene blocks with conjugation system promising as materials with special electrical, physical, catalytic, and sorption properties have been prepared by the reaction of poly(vinyl chloride) with sodium salts of 1,2,4-triazole and 1,2,3-benzotriazole in a dimethylformamide medium.     

Anomalous viscosity behavior of rodlike polyelectrolytes: Partially sulfonated poly(2-benzoyl-1,4-phenylene)s in aqueous solution

Two stereoisomeric poly(2-benzoyl-1,4-phenylene)s were synthesized. Polymer I has exclusively a head-to-tail structure; however, polymer II contains both head-to-head and head-to-tail units. The sulfonation reaction of polymers I and II was found to occur mainly on the meta position of the benzoyl group on the phenylene backbone. The viscosities of polymers Ia (27% sulfonated) and Ic (51% sulfonated) in aqueous solutions at 25°C were measured with and without NaBr addition. Upon the addition of NaBr (0.05 and 0.1M), the reduced viscosities were found to increase gradually and reach a constant value in each case after standing at room temperature for 30–40 h. Without NaBr, the time effect was not found. The reduced viscosities of solutions with NaBr were also higher than those without the salt. These results are quite different from the typical “polyelectrolyte” behavior. A possible explanation of the salt effect of rigid rodlike polymers such as sulfonated poly(2-benzoyl-1,4-phenylene) is discussed. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1425–1429, 1998     

Synthesis and self-assembly behavior of thermoresponsive poly(oligo(ethylene glycol) methyl ether methacrylate)-POSS with tunable lower critical solution temperature

This article reports on the synthesis of a novel amphiphilic polyhedral oligomeric silsesquioxane (POSS) end-capped poly(2-(2-methoxyethoxy)ethyl methacrylate)-co-oligo(ethylene glycol) methacrylate) (POSS-P(MEO₂MA-co-OEGMA)). These thermoresponsive organic–inorganic hybrid polymers exhibit critical phase transition temperature in water, which can be finely tuned by changing the feed ratio of OEGMA and MEO₂MA. The lower critical solution temperature (LCST) of POSS-P(MEO₂MA-co-OEGMA) increases from 31 to 59 °C with the increasing of OEGMA content. Dynamic light scattering (DLS) and transmission electron microscopy (TEM) studies show that these polymers can self-assemble into spherical micelles with the thermosensitive block into the corona and the POSS forming the core, and larger aggregates are formed when the temperature values are above their LCSTs. These thermoresponsive polymers POSS-P(MEO₂MA-co-OEGMA) with self-assembly behavior and tunable tempetature-responsive property have the potential applications in material science and biotechnology.     

Influence of oxygen plasma treatment on poly(ether sulphone) films

Poly(ether sulphone) (PES) is one of the most widely used materials in the micro-electronics industry and a good candidate for the substrates of flexible optoelectronic devices. In this work, the influences of oxygen plasma treatment on the surface chemical composition, surface morphology and optical transparency of PES films were investigated by means of X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM) and UV-visible spectrophotometry. The possible relations between the optical transparency of the substrate and the surface roughness and chemical composition were also studied. The oxygen plasma treatment seriously changed the surface chemical composition and made the surface more rough. Considerable amounts of sulphate species were found on the plasma-treated surface and the surface roughness values (R_a) increased monotonically with the increase of the treatment time. The PES films treated by 5 min, 15 min, 30 min and 45 min oxygen plasma demonstrated transmission of approximately 98, 94, 68 and 46%, respectively, in the wavelength range of 400-780 nm. The oxygen plasma induced decline of optical transparency of PES films might be attributed to both the increase of surface roughness and the changes of chemical composition of the film surface.     

Specific features of the polyelectrolyte behavior of weakly charged cryogels of polyacrylamide and poly(N-isopropylacrylamide)

Specific features of the polyelectrolyte behavior of weakly charged common gels and cryogels of copolymers of polyacrylamide and poly(N-isopropylacrylamide) with sodium acrylamido-2-methyl-1-propyl sulfonate are investigated. The cryogels are synthesized in frozen solutions at ?15°C. It is shown that the polyelectrolyte swelling is significantly weaker in the case of cryogels than that in the case of gels synthesized in solutions. For thermosensitive gels with isopropylacrylamide groups, collapse occurs during heating. Charging of a common gel leads to a noticeable (18°C) increase in the transition temperature. For a cryogel, this growth is 3°C. During the interaction with cetylpyridinium chloride, the gel contraction is much more pronounced for common weakly charged gels. At the same time, walls of pores of a collapsed cryogel contain a smaller amount of the solvent. Isotherms of the adsorption of a cationic surfactant by anionic common gels and cryogels differ insignificantly. Model gels synthesized in concentrated acrylamide solutions exhibit very weak polyelectrolyte swelling, similar to that of cryogels. The behavior of cryogels is explained by a very high local concentration of crosslinks due to a strong entanglement of polymer chains.     

Swelling behavior of strong polyelectrolyte poly(N-t-butylacrylamide-co-acrylamide) hydrogels

Temperature-sensitive ionic hydrogels based on N-t-butylacrylamide (TBA), acrylamide (AAm), 2-acrylamido-2-methylpropane sulfonic acid sodium salt (AMPS) and N,N^′-methylenebis(acrylamide) (BAAm) monomers were prepared. The molar ratio of TBA to the monomers AAm and AMPS was fixed at 60/40, while the AMPS content of the hydrogels was varied. The elastic modulus of the hydrogels was in the range of 347-447 Pa, much lower than the modulus of PAAm or poly(N-isopropylacrylamide) hydrogels due to the reduced crosslinking efficiency of BAAm in TBA/AAm copolymerization. The hydrogels exhibited swelling-deswelling transition in water depending on the temperature. Increasing ionic group (AMPS) content resulted in shifting of the transition temperature interval in which the deswelling takes place. The higher the ionic group content, the broader the temperature interval at the phase transition. Ionic hydrogels exhibited first-order reentrant conformational transitions in ethanol-water and in dimethylsulfoxide (DMSO)-water mixtures. The higher the ionic group content of the hydrogels the narrower the ethanol (or DMSO) range in which the reentrant phenomena occur. By taking into account the difference of the solvent mixture composition inside and outside the gel, the equilibrium swelling theory provided a satisfactory agreement to the experimental swelling data of the hydrogels immersed in the solvent mixtures.     

Phase behavior of poly(ethylene oxide) and sulfonated polystyrene blends with and without solvent

The phase behavior of poly (ethylene oxide) (PEO) and poly(styrene-co-sodium sulfonated styrene) (SPS) blends has been examined as a function of copolymer composition. The mixtures show complex coacervation in dilute benzene/methanol (9/1, v/v) solution. The presence of intermolecular interactions between PEO and SPS in solution is verified by viscometry. Interaction between PEO and SPS in the solid state was supported by small-angle x-ray scattering; however, binary blends containing low PEO content show high miscibility, whereas the blends with high PEO content show phase separation.     

Thermoswitching property in TCNQ salts of ionenes containing poly(ethylene oxide) segments

Ionene polymers characterized by the alternating structure of ionene and crystalline poly(ethylene oxide) (PEO) segments were prepared as a function of PEO segment size. A microstructure of these ionenes and their 7,7,8,8-tetracyanoquinodimethane (TCNQ) salts were investigated with x-ray diffraction patterns, thermal scanning behavior, and polarizing micrographs. On the basis of this microstructure, the change in resistivity with temperature was studied. In Arrhenius' plots of the resistivity the simple salts in which the spherulites consisting of the PEO segments were observed showed a sharp decrease in resistivity with a rise in temperature [critical temperature resistor (CTR)] at about the melting point of the PEO segments, whereas the other simple salts in which the spherulites were not observed showed linear temperature dependence. The switching properties were confirmed similarly in repetitive heating/cooling cycles. This CTR characteristic was attributed to an increase in continuity in the conduction paths by melting spherulites. The apparent switching properties were not observed in the complex salts.     

Structure and thermal characterisation of poly(arylene ether sulphone)s

Structurally different poly(arylene ether sulphone) (PES) copolymers were synthesized by reacting stoichiometric amount of dichlorodiphenyl sulphone (DCDPS) with bisphenols. The molar ratio of bisphenol-A and phenolphthalein (ESP)/hydroquinone (ESH)/resorcinol (ESR) was varied to prepare nine copolymer samples. Structural characterization was done by FT-IR and ¹H-NMR studies. The initial decomposition temperature as well as temperature of maximum rate of mass loss in ESR and ESH copolymers were similar and a marginal decrease in these decomposition temperatures were observed by increasing the isopropylidine units in the backbone. High char residue at 800°C was observed in polymers having high content of phthalein units.The paper was presented at Thermans 2004 held at Baroda, January 20–22, 2004.Reliance Industries Limited is gratefully acknowledged for creating a Chair at IIT Delhi (I. K. Varma) and Council of Scientific and Industrial Research for providing scholarship to one of the authors (R. T. S. Muthu Lakshmi).     

A conductivity study and calorimetric analysis of dried poly(sodium 4-styrene sulfonate)/poly(diallyldimethylammonium chloride) polyelectrolyte complexes

Ionically cross-linked polyelectrolyte complexes (PECs) of anionic poly(sodium 4-styrene sulfonate) (PSS) and cationic poly(diallyldimethylammonium chloride) (PDADMAC), xPSS.(1-x)PDADMAC, with molar fractions x ranging from 0.30 to 0.70, were prepared and subsequently dried. The PEC samples were analyzed by differential scanning calorimetry, and the ionic conductivity sigmadc of the samples was measured as a function of temperature by means of impedance spectroscopy. The thermograms display an endothermic peak in the temperature range of 90-143 degrees C, which is attributed to a glass transition of the PEC. The glass transition temperature Tg has a symmetric x dependence with a minimum at x=0.50. The temperature dependence of sigmadcT is not affected by the glass transition. The ionic conductivity of the samples before drying is three orders of magnitude larger than sigmadc after drying; nevertheless, their activation enthalpies are identical. Arrhenius parameters obtained from the systematic study of several PEC compositions are discussed. The ionic conductivity of the PSS-rich samples is significantly higher than sigmadc of PDADMAC-rich samples. This implies a relatively high Na+ mobility as compared to Cl(-) mobility in PEC. In contrast to the symmetric x dependence of Tg, the conductivity of PEC increases and the activation enthalpy decreases with increasing x in the investigated composition range. A strong x dependence of sigmadc is observed for PSS-rich PEC, which is attributed to a significant variation in the mobility of the charge carriers.     

疏水改性聚丙烯酸溶液的流变特性研究

本文通过沉淀聚合制备了具有不同主链结构的疏水改性聚丙烯酸(HMPA),由Huggins方程确定了HMPA在溶液(水,盐/水,醇/水)中的特性粘数[η]和Huggins常数KH,采用流变学法研究了HMPA溶液的疏水缔合行为和流变特性.研究表明,HMPA溶液具有典型的剪切变稀行为,主链结构对HMPA溶液的缔合行为和流变特性有显著影响.主链含有疏水链段的HMPA在乙二醇/水溶液中形成类似弹性体的凝胶网络结构,具有较大的活化能,其表观粘度具有明显的温度敏感性.