Grain boundary segregation of P and micro-structural changes in 12% Cr-steels

Phosphorus occurs as impurity in 12% CrMoV-steels and tends to enrich at grain boundaries. The phosphorus grain boundary segregation in a laboratory cast of the steel X 20 CrMoV 12 1 with a relatively high phosphorus content (0.057% P) was studied by Auger electron spectroscopy and the segregation kinetics and equilibria were described. Using the results phosphorus segregation could be predicted and compared to measured phosphorus concentrations in long-term annealed steels. Investigations by transmission electron microscopy showed recrystallisation and an agglomeration of carbides with aging time and the occurrence of new phases (Laves-phase Fe₂ Mo). All these processes lead first to an increase in toughness as established in notch-impact fracture tests for the laboratory cast, however, after long-term use a reduction in toughness is expected.     

AES study of underclad cracking

The present work deals with the occurrence of underclad cracks in three types of steels differing in the contents of the alloying elements (Cr, Ni, Mn) and in the impurities level (As, Sb, Sn). The presence of the intercrystalline fracture typical for the underclad cracks was proved to be dependent on the temperature and on the ageing time. It follows from the results of Auger electron spectroscopy, that the sulphur and phosphorus segregations accompanied by a higher number of carbide (possibly sulphide) particles cause a decrease of grain boundary strength. Segregations of other impurity elements were not detected at grain boundaries.     

An experimental and theoretical study of surface segregation in a Fe-6at.%Si bicrystal

The analysis of segregation phenomena in bicrystals is an important step for the understanding of combined effects of the elementary diffusion processes involved in the segregation in polycristalline systems. The segregation of Si and P in a Fe-6at.%Si bicrystal with a (100) and (110) surface has been investigated by means of AES (Auger electron spectroscopy). For these experiments the technique of a linearly increased temperature has been applied. Significant differences between the segregation kinetics at the two surfaces of the sample have been found on the one hand for the maximum coverage of P and on the other hand for the high temperature behaviour of Si. Additionally, model calculations based on the KTBIM (kinetic tight binding Ising model) have been performed to qualitatively describe the experimental results. It is shown, that the striking differences between the segregation behaviour at the two differently oriented surfaces can be explained by different segregation energies of P, whereas Si plays a minor role due to its relatively small segregation energy.Dedicated to Professor Dr. rer. nat. Dr. h.c. Hubertus Nickel on the occasion of his 65th birthday     

Ga‐focused ion beam time‐of‐flight secondary ion mass spectrometer analysis of the grain boundary segregation/precipitation of boron in steel

Ga‐focused ion beam time‐of‐flight secondary ion mass spectrometry (FIB‐TOF‐SIMS) analysis was performed to investigate the grain boundary segregation/precipitation of boron in steel. To overcome the low secondary ion yield from the primary Ga⁺ source and the sensitivity using a high‐resolution Ga‐FIB source, a low energy oxygen ion beam was used prior to the Ga‐FIB‐TOF‐SIMS analysis. As a result, it was found that Ga‐FIB‐TOF‐SIMS is a very powerful tool for mapping boron segregation and/or precipitation in steel with a spatial resolution of ~200 nm. In addition, the results were strongly dependent on the surface composition. Copyright © 2014 John Wiley & Sons, Ltd.     

Investigations of the distribution of elements in phases present in G-AlMg5Si cast alloy with EDX/WDX spectrometers and AES

The mechanical properties of most aluminium alloys depend heavily on chemical composition, casting methods and heat treatment. Alloys of type G-AlMg₅Si are known for good corrosion resistance and mechanical properties at elevated temperatures. Under the designation Hydronalium (Hy 511) they are used for the production of heads for air cooled Diesel engines. To obtain better mechanical characteristics, titanium is added to the alloy. This paper deals with the results obtained during investigations of the distribution of elements in binary eutectic Mg₂Si and ternary eutectic as well as the distribution of titanium in samples of Hy 511, obtained during casting of cylinder heads. Studies of the distribution of the elements were performed using EDX/ WDX spectrometry, and the distribution of titanium was studied also with Auger electron spectroscopy.Dedicated to Professor Günther Tölg on the occasion of his 60th birthday     

砷锑铋对阴极铜沉积过程的影响

用线性电位扫描、ＸＰＳ、ＸＲＤ等方法，研究了砷锑铋离子对酸性硫酸铜系统中铜沉积反应动力学及铜沉积层成份与结构的影响．研究表明：Ａｓ（Ⅴ）离子能增大铜沉积反应的交换电流密度，对铜沉积过程起去极化作用；Ｓｂ（Ⅲ）、Ｂｉ（Ⅲ）离子均使铜沉积反应交换电流密度减小，对铜沉积过程起极化作用；但砷锑铋离子不改变铜沉积反应的机理．测试表明：用２００Ａ／ｍ２电流密度电解，砷锑铋不会在阴极沉积，也不影响铜沉积层的晶面择优取向（２２０）；用１５００Ａ／ｍ２电流密度电解，发现砷与铋在阴极与铜共沉积，铜沉积层的晶面择优取向变为（１１１），沉积层中铜主要以金属Ｃｕ和少量Ｃｕ２Ｏ形式存在，铋主要以Ｂｉ２Ｏ３形式存在．     

氢化物发生-原子荧光光谱法测定海洋沉积物中砷、锑、铋、汞、硒

提出了用盐酸-硝酸-水(3+1+4)混合酸消解样品,氢化物发生-原子荧光光谱法测定海洋沉积物样品中砷、锑、铋、汞、硒的方法。考察了原子荧光光谱仪的最佳工作条件。在最佳条件下砷、锑、铋、硒的检出限(3s/k)分别为0.018,0.004,0.001,0.003μg.g-1,汞的检出限(3s/k)为0.604ng.g-1。应用于3种海洋沉积物标准物质的测定,测定值与标准值吻合。     

Determination of As,Sb and Bi in high-purity copper by electrothermal atomic absorption spectrometry

As, Sb and Bi were determined in copper electric cables by atomic absorption spectrometry with electrothermal atomization in a graphite furnace. The interferences in the determination of As, Sb and Bi caused by eleven cationic species and six types of acid were studied. The different volatilization of the copper matrix in comparison to the analyte was studied, as a means of increasing the analyte signal/non-specific absorption signal ratio.     

氢化物发生电感耦合等离子体发射光谱测定土壤样品中痕量砷锑铋

研究了氢化物发生ICP AES法测定土壤样品中痕量As、Sb和Bi的各种条件 ,拟定了分析方法。用本法对 4个土壤标样进行分析 ,结果与推荐值一致。方法的检出限为 (× 1 0 - 6) :As0 .0 7,Sb0 .0 3,Bi0 .0 2。     

X‐ray photoelectron spectroscopy and the pattern recognition method—their application to surface studies in CoPd alloys

In the present work, polycrystalline CoPd alloys in varying range of bulk atomic percent composition (Co30Pd70, Co50Pd50 and Co70Pd30) are investigated by means of X‐ray photoelectron spectroscopy (XPS). The results of conventional XPS quantitative multiline (ML) approach are compared to the results obtained on the basis of XPS lines shape analysis, where the selected XPS or X‐ray induced Auger electron (XAES) transitions, are processed using the pattern recognition method known as the fuzzy k‐nearest neighbour (fkNN) rule. The fkNN rule is applied to the following spectra line shapes: Pd MNV, Co 2p, Co LMM, Pd 3d and valence band, analysing electrons in a varying range of selected kinetic energies. Both methods showed the surface segregation of Pd in Co30Pd70 and Co50Pd50 alloys. The results of the ML, the binding energy shift (ΔBE) analysis and the fkNN rule remained in agreement. Discrepancies in quantitative results obtained using different approaches are discussed within the accuracy of the applied methods, differences due to mean escape depth (MED) of electrons in considered transitions, their depth distribution function, the sensitivity of electron transition line shape on the environmental change (weaker effect for the inner shell transitions, and stronger effect for the outer shell transitions and Auger electron spectroscopy (AES) electrons transitions) and the non‐uniform depth profile concentrations. Copyright © 2005 John Wiley & Sons, Ltd.     

XPS and XAES analysis of copper,arsenic and sulfur chemical state in enargites

Enargite, a copper arsenic sulfide with the formula Cu₃AsS₄ is of environmental concern due to its potential to release toxic arsenic species. The oxidation and dissolution of enargite are governed by the composition and chemical state of the outermost surface layer. Qualitative and quantitative analysis of the enargite surface can be initially obtained on the basis of X‐ray photoelectron spectroscopy (XPS) binding energy and intensity data. However, a more precise determination of the chemical state of the principal elements of enargite (copper, arsenic and sulfur) in the altered surface layer and in the bulk of the mineral requires a combined analysis based on XPS photoelectron lines and the corresponding X‐ray excited Auger lines. On the basis of results obtained on natural and synthetic enargite samples and on standards of sulfides and oxides, the Auger parameter α′ of different compounds was calculated and the Wagner chemical state plots were drawn for arsenic, copper and sulfur. Arsenic in enargite is found to be in a chemical environment similar to that of arsenides or elemental arsenic, whereas copper in enargite is in a chemical state that corresponds to copper sulfide, Cu₂S, for all samples irrespective of surface treatment (natural or freshly cleaved). Only sulfur changed from a chemical state similar to that of copper or iron sulfide in freshly cleaved samples to another state in natural enargite in the as‐received state. Thus, it is the sulfur atom at the surface of enargite that is most susceptible to changes in the enargite surface state and composition. A more detailed interpretation of this behavior, based on differences in the initial and final state effects, is proposed here. The concept of Auger parameter and chemical state plot, used here for the first time for investigating enargite, has proved to be a method to unambiguously assign the chemical state of the principal elements copper, arsenic and sulfur in these minerals. Copyright © 2006 John Wiley & Sons, Ltd.     

Triple Bonds Between Iron and Heavier Group 15 Elements in AFe(CO)3− (A=As,Sb, Bi) Complexes

Heteronuclear transition‐metal–main‐group‐element carbonyl complexes of AsFe(CO)₃^?, SbFe(CO)₃^?, and BiFe(CO)₃^? were produced by a laser vaporization supersonic ion source in the gas phase, and were studied by mass‐selected IR photodissociation spectroscopy and advanced quantum chemistry methods. These complexes have C_3v structures with all of the carbonyl ligands bonded on the iron center, and feature covalent triple bonds between bare Group 15 elements and Fe(CO)₃^?. Chemical bonding analyses on the whole series of AFe(CO)₃^? (A=N, P, As, Sb, Bi, Mc) complexes indicate that the valence orbitals involved in the triple bonds are hybridized 3d and 4p atomic orbitals of iron, leading to an unusual (dp–p) type of transition‐metal–main‐group‐element multiple bonding. The σ‐type three‐orbital interaction between Fe 3d/4p and Group 15 np valence orbitals plays an important role in the bonding and stability of the heavier AFe(CO)₃^? (A=As, Sb, Bi) complexes.     

氢化物-原子荧光光谱法连续测定锌精矿中砷、锑、铋、锡

用氢化物-原子荧光光谱法,一次性分解样品,在L-半胱氨酸存在下,实现了锌精矿中As、Sb、Bi、Sn的连续测定。其回收率分别为92．8％～105．0％、96．0％～109．3％、96．0％～111．6％和96．7％～103．7％;检出限分别为0．35、0．31、0．19和0．35μg／L。用该方法分析锌精矿样品,结果满意。     

Determination of As, Sb, Se, Te and Bi in milk by slurry sampling hydride generation atomic fluorescence spectrometry

A simple and fast analytical procedure has been developed for the determination of As, Sb, Se, Te and Bi in milk samples by hydride generation atomic fluorescence spectrometry (HG-AFS). Samples were treated with aqua regia for 10 min in an ultrasound water bath and pre-reduced with KBr for total Se and Te determination or with KI and ascorbic acid for total As and Sb, the determination of Bi being possible in all with or without pre-reduction. Slurries of samples, in the presence of antifoam A, were treated with NaBH₄ in HCl medium to obtain the corresponding hydrides, and AFS measurements were processed in front of external calibrations prepared and measured in the same way as samples. Results obtained by the developed procedure compare well with those found after microwave-assisted complete digestion of samples. The proposed method is simple and fast, and only 1 ml of milk is needed. The values obtained for detection limit are 2.5, 1.6, 3, 6 and 7 ng l⁻¹ for As, Sb, Se, Te and Bi respectively in the diluted samples, with average relative standard deviation values of 3.8, 3.1, 1.9, 6.4 and 1.2% for three independent analysis of a series of commercially available samples of different origin. Data found in Spanish market samples varied from 3.2±0.3 to 11.3±0.2 ng g⁻¹ As, from 3.1±0.2 to 11.6±0.4 ng g⁻¹ Sb, from 10.7±0.5 to 25.5±0.4 ng g⁻¹ Se, from 0.9±0.2 to 9.4±0.6 ng g⁻¹ Te and from 11.5±0.1 to 27.7±0.4 ng g⁻¹ Bi.     

Theoretical characterizations of HAsXH (X = N, P, As, Sb, and Bi) isomers in the singlet and triplet states

The lowest singlet and triplet potential energy surfaces for all group 15 HAsXH (X = N, P, As, Sb, and Bi) systems have been explored through ab initio calculations. The geometries of the various isomers were determined at the QCISD/LANL2DZdp level and confirmed to be minima by vibrational analysis. In the case of nitrogen, the global minimum is found to be a triplet H(2)NAs structure. For the phosphorus case, singlet trans-HAs==PH is found to be global minima surrounded by large activation barriers, so that it should be observable. For arsenic, theoretical investigations demonstrate that the stability of HAsAsH isomers decreases in the order singlet trans-HAs==AsH > triplet H(2)AsAs > singlet cis-HAs==AsH > triplet HAsAsH > singlet H(2)AsAs. For antimony and bismuth, the theoretical findings suggest that the stability of HAsXH (X = Sb and Bi) systems decreases in the order triplet H(2)AsX approximately singlet trans-HAs==XH > singlet cis-HAs==XH > triplet HAsXH > triplet H(2)XAs > singlet H(2)AsX > singlet H(2)XAs. Our model calculations indicate that the relativistic effect on heavier group 15 elements should play an important role in determining the geometries as well as the stability of HAsXH molecules. The results obtained are in good agreement with the available experimental data and allow a number of predictions to be made.     

Determination of As, Sb, Bi and Hg in water samples by flow-injection inductively coupled plasma mass spectrometry with an in-situ nebulizer/hydride generator

A simple and very inexpensive in-situ nebulizer/hydride generator was used with inductively coupled plasma mass spectrometry (ICP-MS) for the determination of As, Sb, Bi and Hg in water samples. The application of hydride generation ICP-MS alleviated the sensitivity problem of As, Sb, Bi and Hg determinations encountered when the conventional pneumatic nebulizer was used for sample introduction. The sample was introduced by flow injection to minimize the deposition of solids on the sampling orifice. The elements in the sample were reduced to the lower oxidation states with L-cysteine before being injected into the hydride generation system. This method has a detection limit of 0.003, 0.003, 0.017 and 0.17 ng ml⁻¹ for As, Bi, Sb and Hg, respectively. This method was applied to determine As, Sb, Bi and Hg in a CASS-3 nearshore seawater reference sample, a SLRS-2 riverine water reference sample and a tap water collected from National Sun Yat-Sen University. The concentrations of the elements were determined by standard addition method. The precision was better than 20% for most of the determinations.     

Investigation of the automated determination of As,Sb and Bi by flow-injection hydride generation using in-situ trapping on stable coatings in graphite furnace atomic absorption spectrometry

Flow-injection hydride generation and in situ concentration of As, Sb and Bi hydrides in graphite furnace atomic absorption spectrometry can be automated by means of a long-term stable trapping reagent replacing the Pd modifier. In a systematic study, carbide-forming elements (Zr, Nb, Ta, W) and noble metals (Ir, Ir/Mg, Pd/Ir) were investigated as stable adsorbers which require only a single application. Trapping temperature curves indicate high signals for trapping of As at 750–800°C, Sb at 450–8000°C and Bi at 100–500°C on Zr-coated tubes. Ir- and Ir/Mg-coated tubes showed a high response for Sb and Bi at lower temperatures, but based on signal stability and reproducibility (over 400 trapping and atomization cycles tested) the better performance was found with the Zr-coated tubes. The radiotracers Sb-125 and Bi-207 were used to measure the hydride generation (>95% for both elements) and trapping efficiency (91% for Sb and 56% for Bi) on the Zr-coated tube. An adsorptive carry-over effect was observed with Sb and Bi but not with As, and trapping temperatures above 450°C with Sb and 350°C with Bi (the critical temperatures) can lead to errors in absorbance values. On a Zr-coated tube the characteristic mass was about 16 pg for As, 15 pg for Sb and 9 pg for Bi (peak height) and the detection limits (3 sigma) were about 0.015, 0.010 and 0.027 ng, respectively, with a 1 ml sample loop. The method was tested by the determination of the elements in NIST low-alloy steel certified reference materials.     

ChemInform Abstract: Probing the Electronic Structure and Aromaticity of Pentapnictogen Cluster Anions Pn5‐ (Pn: P,As, Sb,and Bi) Using Photoelectron Spectroscopy and ab initio Calculations.

ChemInform is a weekly Abstracting Service, delivering concise information at a glance that was extracted from about 100 leading journals. To access a ChemInform Abstract of an article which was published elsewhere, please select a “Full Text” option. The original article is trackable via the “References” option.     

Corroles with group 15 metal ions. Synthesis and characterization of octaethylcorroles containing As, Sb, and Bi ions in +3, +4, and oxidation states

The synthesis, spectroscopic characterization, and electrochemistry of As, Sb, and Bi corroles are reported. The investigated complexes are represented by [(OEC)AsV(CH3)]+ClO4- and (OEC)M where M = As(III), Sb(III), or Bi(III) and OEC is the trianion of octaethylcorrole. The products of each redox reaction are characterized by UV-vis and ESR spectroscopy. The first one-electron oxidations of (OEC)As and (OEC)Sb are metal-centered and result in the formation of [(OEC)AsIV]+ and [(OEC)SbIV]+. A second one-electron oxidations generates [(OEC)AsV]2+ and [(OEC.)SbIV]2+, the latter of which is slowly converted to a Sb(V) corrole, [(OEC)SbV]2+. The first one-electron oxidation of (OEC)Bi leads only to the Bi(III) pi-cation radical, but a second one-electron oxidation is proposed to give a Bi(IV) complex, [(OEC)Bi]2+. The first reduction of [(OEC)AsV(CH3)]+ClO4- is accompanied by loss of the sigma-bonded methyl ligand and formation of an As(III) complex.     

The analytical and descriptive inorganic chemistry of the hydrolysis of hexafluoropnictate ions, PnF6 (Pn = P, As, Sb, Bi)

The rates of aqueous hydrolysis of the hexafluoropnictate ions, PnF₆⁻ (Pn=P, As, Sb, Bi) were determined using a fluoride ion selective electrode and understood qualitatively in terms of ionic size and polarizability of the central atom. Both S_N2 and S_N1 (i.e. associative and dissociative) hydrolysis are discussed as are the competing roles of acid and base in the reaction. (Valence) isoelectronic analogies are also given. Regardless of the interpretation or reaction conditions, it is unequivocal that the hydrolysis rate is measurably rapid for the hexafluoroantimonate. By contrast, it is negligible for both hexafluorophosphate and hexafluoroarsenate.