基于DFB腔注入锁定效应的可调谐光电振荡器

提出一种基于分布反馈光注入锁定效应的可调谐光电振荡器,其环路主要由马赫曾德尔调制器、光电探测器、环形器、分布反馈激光器和射频放大器顺接而成,分布反馈激光器是系统关键器件,通过分布反馈激光器光注入锁定效应,分布反馈腔在光域实现了微波光子滤波器功能,无需传统光电振荡器必须的射频带通滤波器.同时,由于分布反馈激光器注入锁定提高了环路Q值,因此系统可采用短环路结构,从而降低了光纤因温度敏感对微波信号稳定性的影响并减小了整个系统的尺寸.另外,通过调节注入光波长和功率可改变该微波光子滤波器的中心频率,从而可实现系统的可调谐性.理论分析了该光电振荡器的原理和微波光子滤波器的调谐性,在此基础上开展了实验验证.结果表明该光电振荡器能够产生18.7～21.6 GHz的可调微波信号,在1 kHz频偏处的相位噪声为-90 dBc/Hz.     

基于DFB腔注入锁定效应的可调谐光电振荡器（英文）

提出一种基于分布反馈光注入锁定效应的可调谐光电振荡器,其环路主要由马赫曾德尔调制器、光电探测器、环形器、分布反馈激光器和射频放大器顺接而成.分布反馈激光器是系统关键器件,通过分布反馈激光器光注入锁定效应,分布反馈腔在光域实现了微波光子滤波器功能,无需传统光电振荡器必须的射频带通滤波器.同时,由于分布反馈激光器注入锁定提高了环路Q值,因此系统可采用短环路结构,从而降低了光纤因温度敏感对微波信号稳定性的影响并减小了整个系统的尺寸.另外,通过调节注入光波长和功率可改变该微波光子滤波器的中心频率,从而可实现系统的可调谐性.理论分析了该光电振荡器的原理和微波光子滤波器的调谐性,在此基础上开展了实验验证.结果表明该光电振荡器能够产生18.7~21.6GHz的可调微波信号,在1kHz频偏处的相位噪声为-90dBc/Hz.     

结合光注入半导体激光器与光电环路产生频率大范围可调、窄线宽微波信号

结合光注入半导体激光器的单周期动力学态与光电环路,提出了一种可获得频率大范围可调、窄线宽的光子微波信号的方案并进行了实验研究.结果表明,光注入半导体激光器在一定条件下能够实现单周期振荡,且光子微波信号的频率在8~67GHz范围内连续可调;在合适的注入参数下,获得了频率为24.3GHz且光谱具有单边带结构的光子微波信号;通过引入光电环路结构,能够有效地将该光子微波的线宽由8.6 MHz压缩至30kHz,并获得了40dB以上的信噪比.     

基于双路光电反馈下光注入半导体激光器的高性能线性调频信号产生

提出了一种基于双路光电反馈下,光注入半导体激光器的高性能微波线性调频信号产生方案,并进行了实验验证.在合适的注入参数下,光注入半导体激光器可工作于单周期振荡态,生成频率由注入强度和失谐频率决定的可调谐微波信号.通过加载波形为类三角波的电压信号控制注入强度,光注入半导体激光器可生成宽带微波线性调频信号.进一步通过引入延时匹配的双路光电反馈环路,来提升光注入半导体激光器生成线性调频信号的质量:分别基于傅里叶域模式锁定原理和自注入锁定技术,引入短环光电反馈和长环光电反馈,以同时实现线性调频信号的梳齿信噪比提升和线宽窄化.在验证实验中,本方案产生了带宽为8 GHz(18—26 GHz)的线性调频信号,其梳齿信噪比达到40 dB,梳齿线宽为1 kHz.实验结果证明了本方案能够生成同时具有大带宽、高梳齿信噪比、窄线宽且相位关系稳定的高性能微波线性调频信号.     

强光注入提高光反馈VCSELs混沌载波基频

研究了外部光注入对光反馈垂直腔表面发射半导体激光器(VCSEL)混沌载波基频的影响.研究结果表明：当外部注入光频率与VCSEL自由运行的振荡频率失谐一定时,随着外部光注入强度的增加,混沌载波基频总体呈现上升的趋势;通过调整失谐频率和注入强度大小,外部光注入可以使混沌载波基频得到大幅度的提高;当归一化的注入系数K=330, 失谐频率为42 GHz,可得到基频位于47.3 GHz的混沌信号输出. 关键词： VCSEL 光注入 光反馈 混沌载波基频     

光注入半导体激光器产生可调谐高频微波

利用光注入半导体激光器产生的单周期振荡,实验获得了61—129 GHz范围内频率连续可调的微波光信号.同时利用半导体激光器速率方程,对光注入半导体激光器产生高频微波进行了数值模拟.模拟和实验结果均表明微波信号产生于注入光和激光器腔模之间的拍频现象,其频率随着注入光强度和波长失谐的增大而增大,模拟结果预测该方法可以产生频率大于40 GHz的高频微波. 关键词： 光通信 光生微波 拍频 半导体激光器     

基于FP-LD注入的无本振光载波全光混频技术

提出了一种基于低速信号注入法布里-珀罗型激光二极管(FP-LD)的无本振全光混频技术,利用FP-LD的一个纵模和外部注入信号光的四波混频作用生成的边带锁定纵模产生光载射频信号。通过改变FP-LD的注入光信号强度和偏振态实现副载波频率可变,并根据FP-LD注入锁定特性分析实验结果得到的不同边模抑制比。实验中采用2.7,2.5,1.25 Gb/s非归零(NRZ)码注入FP-LD实现副载波频率分别为16.2,10.0,18.2和20.0 GHz的全光混频,测量16.2 GHz的副载波得到了10 kHz偏移处单边带相位噪声为-81.2,-87.7 dBc/Hz。     

基于平行偏振光注入的1550nm波段垂直腔表面发射激光器获取窄线宽光子微波的理论和实验研究

提出一种基于1550 nm垂直腔表面发射激光器(1550 nm-VCSEL)获取高质量微波信号的全光方案.在该方案中,采用波长位于VCSEL中被抑制模式的中心波长附近、振动方向与VCSEL中主导模式相同的偏振光注入(即平行注入)1550 nm-VCSEL获取高频微波,并借助双光反馈对该高频微波的线宽进行窄化.一方面,基于VCSEL的自旋反转模型,从理论上分析了采用该方案产生微波信号的可行性;另一方面,通过构建相应的实验系统,对该方案产生的微波的特性进行初步实验研究.实验结果表明:在合适的注入条件下,1550 nm-VCSEL能够产生30 GHz左右的微波信号,但该信号的线宽较宽(百兆水平);引入双光反馈后,微波线宽可被压窄两个数量级以上,得到了线宽低于1 MHz、信噪比大于40 d B的微波信号.     

光载毫米波上变频系统的设计与研究

对光载毫米波(ROF)系统中毫米波副载波的上变频方案进行了理论分析及仿真研究。在中心站端通过30GHz的本地振荡源,采用载波抑制技术得到了差频为60GHz的光载射频信号,即在中心站实现了上变频的处理。该系统不需要在基站设置高频震荡源,大大降低了ROF系统的成本,满足了未来光无线通信系统中不断增长的载波频率的要求。同时,理论分析了中心站上变频的信号产生方法,搭建了仿真系统,结合理论分析结果,验证了该方案产生的ROF信号在光线中的传输性能及传输距离。     

基于光电负反馈的光注入1550nm垂直腔面发射激光器产生窄线宽微波信号

基于1 550nm垂直腔面发射激光器在平行偏振光注入下呈现的单周期非线性动力学状态,进一步引入光电负反馈,得到了高质量的微波信号.实验研究结果表明:平行偏振光注入下,通过调节注入光的注入强度及频率,1 550nm垂直腔面发射激光器可呈现注入锁定、单周期、倍周期、混沌等多种非线性动力学状态;在合适的注入参量下,平行偏振光注入1 550nm垂直腔面发射激光器可产生光谱具有单边带结构、频率超过10GHz的光子微波信号,但该微波信号的线宽较宽(达MHz量级);进一步引入光电负反馈后,通过选取合适的光电反馈强度,可将该微波信号的线宽减小至一百多kHz(减小两个量级以上);在选择优化的反馈强度条件下,仅通过简单调节注入光强度,可实现窄线宽光子微波信号的频率在一定范围内连续可调谐.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.