热释电IRFPA非均匀性校正实验系统研究

采用虚拟仪器技术,设计了基于LabVIEW软件平台的热释电IRFPA（红外焦平面阵列）非均匀性校正系统。该系统可通过控制面板选择校正算法,选取3种不同的标准像元的标准校正曲线。可以对IRFPA待校正的像元输出进行采集,对非均匀性参数进行测试,还可以进行非均匀性校正。系统通过三维波形以及图像的显示来观察校正前后对比,并能计算出校正前后的NU（非均匀性）值大小。对像元数为120160的热释电IRFPA输出的视频信号进行了非均匀性校正实验,对非均匀性校正算法进行了统计对比,对仿真结果及数据进行了分析总结。经过校正实验验证了系统的可行性,结果证明基于平均值法的两点定标算法对热释电IRFPA非均匀性校正后的NU值是最小的。通过统计数据得出校正后的NU可平均下降30%。     

一种基于S曲线模型的红外焦平面阵列非均匀性自适应校正算法

针对红外焦平面阵列(IRFPA)中探测元的非线性响应以及响应特性的漂移引起的校正误差,提出了一种基于S曲线模型的场景自适应校正算法.该算法利用对数运算将IRFPA的输出信号线性化.并运用自适应滤波技术对线性信号实施非均匀性校正,并采用指数变换还原出实际的校正输出信号.基于人造黑体图像和实景红外视频的仿真实验结果表明.该算法在校正精度和大动态范围信号响应特性方面均优于传统的场景自适应校正算法.     

基于焦平面归一化响应特性的红外非均匀性校正

红外焦平面阵列的非均匀性噪音是制约红外成像质量的主要因素,非均匀性校正是红外焦平面器件应用的一个关键技术.本文提出了一种基于焦平面归一化响应特性且易于实现的非均匀性校正算法,并基于像元分布的卡方直方图提出一种新的图像非均匀性评估方法,即校正比例.该方法的校正输出考虑了每个像元的观测值与焦平面的响应信号的平均值,校正参量通过将像元的输出与其理想校正结果之间的偏差用焦平面响应的平均值建立联系而计算得到.提出的校正比例兼顾考虑了焦平面响应的时间与空间特性,比现有的图像非均匀性评估方法更能合理衡量焦平面的非均匀性程度.多种非均匀性校正的评价数据以及实验结果表明,该算法的校正效果优于两点校正法与原值拟合二阶校正法,并对于响应异常的像元具有较强的校正能力.此外其校正准确度高,所需参量少,易于实时处理,具有较强的实用价值.     

HgCdTe短波红外焦平面探测器校正技术

在短波红外成像光谱技术的应用背景下,对HgCdTe短波红外焦平面探测器的校正技术进行研究,包括坏像元校正和非均匀性校正,并提出先进行坏像元校正后进行非均匀性校正的探测器校正原则;在标准辐射源下,对正常像元的输出值进行正态分布拟合,并通过3σ准则设定正常像元输出值阈值的方法,确定探测器中坏像元的数量与位置,然后根据短波红外成像光谱技术的应用要求,对坏像元进行光谱二邻域均值替换;坏像元校正完成后,再采用运算量小、实时性强的两点法对探测器进行非均匀性校正。综合校正结果表明:探测器坏像元得到有效剔除,坏像元输出值得到良好校正,且非均匀性校正效果明显,图像细节更加丰富。     

基于自适应滤波的红外焦平面阵列非均匀性校正算法

 红外探测器响应漂移特性会降低红外焦平面阵列（IRFPA）非均匀性校正的精度。针对该问题提出了一种基于场景的IRFPA非均匀性校正算法。该算法利用所获得的序列成像场景信息,采用一种基于快速自适应滤波器的最优化递归估计方法来获得非均匀性校正参数,并利用当前的成像信息来更新校正参数,以此降低探测器响应漂移特性对非均匀性校正的影响。算法仿真实验显示,对非线性参数为26.12%的同一图像,使用该算法、两点校正算法和卡尔曼滤波校正算法校正1 h后,可分别将非线性参数降至1.856%,3.122%和1.893%,说明该算法可获得稳定而较好的非均匀性校正效果。     

基于焦平面归一化响应特性的红外非均匀性校正

红外焦平面阵列的非均匀性噪音是制约红外成像质量的主要因素,非均匀性校正是红外焦平面器件应用的一个关键技术.本文提出了一种基于焦平面归一化响应特性且易于实现的非均匀性校正算法,并基于像元分布的卡方直方图提出一种新的图像非均匀性评估方法,即校正比例.该方法的校正输出考虑了每个像元的观测值与焦平面的响应信号的平均值,校正参量...     

多通道热释电IRFPA图像拼接采集系统

为了实现分辨率高的大规模热释电IRFPA探测器,设计了多路通道并行输出的读出电路。针对多路输出的热释电IRFPA探测器,依据热释电探测的时序要求,设计了图像拼接采集系统。利用外部驱动信号控制采集卡的触发及采样时钟,由斩波器同步信号判断热释电探测器的亮场及暗场信号。构造PC-DAQ虚拟仪器系统对多通道输出的热释电型IRFPA进行多路并行图像采集,并对每路图像信号进行亮、暗场判断后进行差分处理,通过软件拼接处理成一副完整的图像,最终在软件平台上显示。对实验室研制的160列120行双通道读出及320列120行四通道读出的热释电读出电路进行了图像采集实验,对于同样阵列大小的单通道读出探测器,双通道结构读出速度提高了1倍,四通道结构读出速度提高了3倍。通过采集成像实验验证了系统的可行性。     

基于衬底温度和贝叶斯估计的红外非均匀性校正（英）

分析了红外焦平面阵列(IRFPA)基于定标的非均匀性校正法(NUC)和基于场景的NUC算法各自的优势和问题,在此基础上提出了联合非均匀性校正方法。根据上电时刻焦平面衬底的温度值,从FLASH中提取事先存储的对应温度区间的增益和偏置校正参数,初步消除探测器的非均匀性。通过分析初步校正后图像残余非均匀性噪声的特性,提出了一种自适应非均匀性校正算法NSCT,对经过NSCT分解后的子带图像,利用贝叶斯阈值逐点进行信号方差和噪声方差估计,计算出残余非均匀性噪声后并加以去除。实验结果表明,该算法能有效提高校正精度,并具有更强的环境适应性。     

基于衬底温度和贝叶斯估计的红外非均匀性校正（英文）

分析了红外焦平面阵列(IRFPA)基于定标的非均匀性校正法(NUC)和基于场景的NUC算法各自的优势和问题,在此基础上提出了联合非均匀性校正方法。根据上电时刻焦平面衬底的温度值,从FLASH中提取事先存储的对应温度区间的增益和偏置校正参数,初步消除探测器的非均匀性。通过分析初步校正后图像残余非均匀性噪声的特性,提出了一种自适应非均匀性校正算法NSCT,对经过NSCT分解后的子带图像,利用贝叶斯阈值逐点进行信号方差和噪声方差估计,计算出残余非均匀性噪声后并加以去除。实验结果表明,该算法能有效提高校正精度,并具有更强的环境适应性。     

一种基于场景的红外焦平面阵列非均匀性校正算法

针对IRFPA器件在工程使用中固定图案噪音会发生漂移及探测元响应呈现非线性的特征,提出了一种以二次方程表征的响应特性数学模型,并利用场景数据的卡尔曼滤波算法,对其实施双校正。本算法较基于线性模型的非均匀性校正算法具有更好的校正效果,仿真实验结果验明了算法的优越性.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.