用于频域光学相干层析成像的深度分辨色散补偿方法

提出一种深度分辨的色散补偿方法,用于增强频域光学相干层析成像的纵向分辨率。将频域光学相干层析成像采集的干涉谱信号傅里叶变换到空域,获取对应不同深度的干涉谱条纹相位,通过对其进行调整实现对被测样品不同深度处的色散的精确补偿。避免传统方法中采用统一色散系数进行色散补偿所带来的过补偿与欠补偿误差,可以有效消除色散引起的频域光学相干层析成像系统点扩展函数的展宽和扭曲。模拟和实验结果表明,基于深度分辨的色散补偿方法在样品的全深度探测范围内可以达到较佳的补偿效果,可有效提高光学相干层析成像系统的纵向分辨率。     

提高光学相干层析成像纵向分辨率的方法

光学相干层析成像技术是一种新型的成像技术，能实现对活体生物组织（透明和不透明）非接触、无伤害、高分辨率的体内断面成像。光学相干层析成像利用相干门技术，其纵向分辨率取决于光源的相干长度，要进一步提高它的纵向分辨率必须从光源入手，本文对采用不同光源提高光学相干层析成像纵向分辨率的方法进行了详细的讨论。     

基于非均匀快速傅里叶变换的干涉合成孔径显微算法

在频域光学相干层析(SDOCT)系统中,样品仅在焦深范围内有高横向分辨率,在焦外分辨率降低。干涉合成孔径显微术(ISAM)是一种三维图像重构算法,可以改善离焦区的图像模糊状况,达到在所有成像深度中都可以获得焦平面处横向分辨率的效果,同时可以解决SDOCT中系统的横向分辨率和成像深度之间的矛盾。介绍了ISAM重构算法的原理和适用的范围,对比分析了传统SDOCT成像算法和经过ISAM重构算法处理的成像图像结果。将非均匀快速傅里叶变换引入ISAM算法,实验结果表明该方法极大地节省了运算时间,提升了实时成像高分辨率SDOCT系统的性能。     

光学相干层析成像随深度变化的色散补偿方法

提出一种随深度变化的色散补偿方法,用以提升频域光学相干层析成像系统的纵向分辨率。该方法利用迭代算法计算出不同成像深度处的色散补偿系数,通过数值计算,得到色散补偿系数与成像深度的关系表达式,计算出各成像深度处的色散补偿系数,利用这些色散补偿系数消除相应深度位置处信号的高阶色散相位,从而有针对性地对系统中参考臂与样品臂的色散失配进行补偿,消除色散的展宽效应。理论推导和实验结果表明,光学相干层析成像系统中,随深度变化的色散补偿方法对各成像深度位置处的信号,包括成像深度较深位置处的弱信号,均可以进行有效的色散补偿,进而得到更多的样品结构信息。     

新型成像技术的实验系统研究

光学相干层析成像是一种新型成像技术。超辐射发光二极管和超短脉冲飞秒激光是能满足成像系统要求的理想光源。在开展光学相干层析相关技术研究的基础上 ,建立了国内第一台上述两种光源的成像实验研究装置 ,对系统的横向、纵向分辨率等基本性能进行了测定 ;并对多种实际样品进行了层析成像。     

正弦相位调制的频域光学相干层析成像

提出一种基于正弦相位调制的频域光学相干层析成像,利用正弦相位调制干涉术探测复频域干涉条纹的实部和虚部,重建复频域干涉条纹。对该复频域干涉条纹作逆傅里叶变换后,消除了频域光学相干层析成像中存在的复共轭镜像以及直流背景和自相干噪声。对玻璃片样品进行了层析成像实验。实验结果表明,采用正弦相位调制的频域光学相干层析成像,将可利用的成像深度范围扩大到原来的2倍,实现了全深度探测的频域光学相干层析成像。     

光纤型光学相干层析成像系统的研制

光学相干层析(OCT)成像技术是一新近发展的高分辨力生物医学成像手段,能非侵入性地对活体内部的结构与生理功能进行可视化观察。采用宽带近红外光源,基于迈克耳孙干涉原理和外差探测方法,建立了单模光纤型光学相干层析成像系统,相干地提取从生物体内部返回的深度分辨的弹性散射光信息,并依此构筑了自然状态下活体组织的二维光学相干层析成像图像和三维光学相干层析成像图像。光纤化设计的光学相干层析成像系统紧凑、灵活,便于与光纤导管、内窥镜和其它成像装置的有机结合,以拓展其观察范围和应用领域。     

线照明并行谱域光学相干层析成像系统与缺陷检测应用研究

针对玻璃缺陷在线无损检测的迫切需求,本文报道了一种基于线照明并行谱域光学相干层析成像系统的大视场检测系统.该系统采用快速面阵CMOS相机,单次拍摄即可获取完整的横截面(B-scan)图像.基于线照明面阵探测器的并行谱域光学相干层析成像系统,可以同时获取沿线照明方向各位置处的深度分辨信息,避免了横向扫描机构的应用.研制系统的轴向分辨率为17.9μm,并行方向上的横向分辨率55.7μm,扫描方向上的横向分辨率为24.8μm,轴向扫描速率为128 000 A-scan/s,横向视场为32 mm,空气中成像深度大于6 mm,成像灵敏度达到62 dB以上.利用研制的线照明并行谱域光学相干层析成像系统,开展了不同类型玻璃表面及其内部缺陷的检测应用研究.     

一种频域光学相干层析成像深度分辨率增强技术EI北大核心CSCD

提出了一种基于光谱整形的频域光学相干层析成像分辨率增强技术。利用光源的自身谱形对探测的频域信号进行整形,以获得深度分辨率更高的空域信号。理论分析和模拟结果表明,对谱形为高斯型和非高斯型的光源,使用该技术均可提高分辨率。     

光学相干层析成像色散补偿研究

针对通过增加光源谱宽度来提高光学相干层析成像系统分辨率时样品色散特性的限制作用,分析了色散与光学相干层析成像系统纵向光程分辨率的约束关系.根据物质色散特性,采用数值变换方法对光学相干层析成像相干成像信号进行了色散补偿.实验使用了中心波长1 550 nm 自激发辐射光源和光纤迈克尓逊干涉结构,对水和光学快速扫描延迟线引入的二阶和三阶色散进行了数值补偿并通过相位修正因子来改善补偿效果.确定了一种普适的、快速的数值色散补偿方法.在对水中盖玻片和生物组织和的光学相干层析成像图像的色散补偿实验中取得了良好的效果,证明了方法的可行性.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.