基于近场均匀照明的LED阵列的优化设计

基于几何光学与辐射照度理论,对菱形、环形和蜂窝状等3种典型LED阵列光源在近场上的照度分布进行研究,推导了不同阵列光源照射到目标面上的总辐射照度表达式,并依据斯派罗法则确定了LED间的最优化距离。进而根据照度公式,对LED阵列进行了仿真和对比分析,得出了不同阵列的光照度分布特点。菱形阵列可以得到较大范围的平坦度,环形阵列的平坦范围较小,能量集中分布在一个圆形范围内,有良好的集光效果,蜂窝状阵列的照度比较集中且占用的面板空间较小,可在一定程度上降低设计成本。     

微型曲面发光二极管阵列照度一致性研究

为提高微型曲面发光二极管(LED)阵列在显示及照明使用方面的舒适度,针对微型曲面LED阵列照度分布的均匀性问题进行研究.采用TracePro光线追迹法分别计算了柱面显示阵列及球面照明阵列的照度分布.计算结果表明,曲面弯曲半径R和光源辐射参数m是影响柱面阵列照度分布的主要因素.通过合理排布阵列像素单元位置,可以增强器件显示均匀度,提高能量利用效率.10×10柱面LED阵列最大平坦化照度均匀度为90.5%.对球面环形阵列照度分布计算结果表明,单环形LED阵列照度均匀性与像素数量无关.影响球面多环LED阵列照度分布的参数主要包括环线分布系数K、环法线与第一环阵列光源法线夹角(?)_0及各环线像素光通量之比φ.以双环LED阵列为模型进行计算,获得最大平坦化照度均匀度为94.8%.调整球面多环阵列位置参数可实现不同照度分布模式.实验对比了微型LED像素单元夹角θ分别为13°,15°和17°时的照度分布,实验结果与理论计算较为一致.本文取得的理论与实验结果可以为微型曲面LED显示及多模式智能照明设计提供参考.     

基于MATLAB的LED阵列的研究与仿真

由于单颗LED的功率很小,作为照明光源使用时需要采用LED阵列形式。首先推导LED阵列的照度叠加公式,根据叠加公式对阵列进行仿真,以圆形为例分析LED在平面上的均匀分布以及以球表面为例分析LED在曲面上的均匀分布。给出两种LED阵列分布的仿真结果,得出不同阵列的分布特点。指出圆面阵列的照射范围比较集中,此类阵列分布的灯具适用于照射面较小且比较集中的照射领域;球表面上的阵列的照射分布范围比较广,呈圆面,此类阵列分布的灯具适用于照射面较大但照度要求不是很高的照射区域。该结果为LED灯具设计提供了依据。     

基于多目标人工鱼群算法的光疗LED照度优化研究

提高发光二极管（light emitting diode,LED）组成的光疗光源在照射平面上的照度均匀分布水平,对于光疗设备发展具有重要的价值。提出了一种基于多目标人工鱼群算法的光疗LED光源的照度优化方法。设计了2种不同组合模式的光疗LED光源阵列。结合多目标人工鱼群算法对光疗LED光源阵列组合数据进行优化,使光疗LED光源阵列的照度分布更加均匀。将优化设计后的光疗LED 光源芯片组合数据,导入光学仿真软件TracePro实现仿真验证,得到经优化的圆形光源排列的照度均匀程度较未优化圆形光源排列提升0.104,矩形光源排列的照度均匀程度较未优化矩形光源排列提升0.148。对比分析最终数据,验证了该优化方法是可行的,可以提高光疗LED光源的照度分布水平。     

积分球辐射光源照度均匀性研究

针对CCD等焦面阵列光电器件常被置于积分球辐射光源出口平面进行测试的误区,研究了积分球辐射光源照度分布的均匀性,得到了合理使用积分球光源测试光电器件的依据。基于数值解析方法和蒙特卡罗方法,建立了理想积分球辐射光源照度均匀性数学模型和非理想积分球辐射光源照度均匀性仿真模型,分析了与积分球光源出口不同距离处光电器件受光面上照度分布情况,并实验测试了两套积分球辐射光源照度分布情况,得到了与积分球辐射光源不同距离处光电器件受光面上照度均匀性分布规律。研究表明:当光电器件受光面直径小于积分球光源出口直径一半、光电器件和积分球出口之间的距离与积分球出口直径的比值在3至5之间时,可在光电器件受光面上获得均匀性优于99%的照度场。     

用于动物细胞和组织培养的新型LED生物光源系列

采用透镜组扩大光束、透镜阵列聚焦和点阵光曲面聚集光能三种光路设计,通过选择各光源中的四个工作参数调节光源输出的辐射照度,本文研制出可用于动物细胞和组织培养使用的、不同强度的三种新型LED生物光源,并使用统计分析软件SPSS拟合得出它们的辐射照度经验计算公式.     

基于菌落挑选仪的暗视场照明的优化设计

针对高通量菌落挑选仪研发的照明设计,采用暗视场照明方式,在保证照度均匀的同时大幅提升了所采集菌落图像的对比度,以提高仪器整体性能。分析了影响照度均匀度的三个重要因素,LED环形光源中灯珠的投射角度、LED环形光源的阵列层数以及LED环形光源距目标面距离。模拟结果表明,当灯珠投射角度为75°、LED环形光源阵列为三层以及LED环形光源距目标面距离为61cm时,照度均匀度最优为93.16%。采用所设计的暗视场照明方式搭建实验系统,实验结果达到项目要求,并与软件模拟结果相匹配。     

紫外LED圆环阵列均匀照明的实现方法

为构造指纹荧光检测中所需的均匀照明紫外光源,选择紫外LED阵列照明。采用光电探测器检测单颗LED的辐射角分布,拟合单个LED角分布函数;用8颗LED均匀置于半径为10 mm的圆环上,在圆环上方5 mm处的中心轴上放置一个LED;在给定的观察屏上照度不均匀误差下,根据斯派罗法则,确定观测屏与圆环阵列之间的距离,从而实现LED圆环阵列的照度分布均匀化。也可以给定观测屏到圆环的距离,确定轴上LED放置点到圆环的距离。实验结果表明,观测屏到圆环距离为11.0 cm时,在半径为10.0 mm的圆域内,照度不均匀相对误差小于1.27%。     

CCD摄像机照度检测装置的研制

为了研制一种照度检测范围宽、结构简单、操作简便,并能产生均匀光辐射分布、自动调光的照度测量装置,通过对传统照度测试方法所使用的结构形式和光源进行分析,提出了一种采用曲面反光灯杯加内置灯的光源以及单片机自动控制的新型CCD摄像机照度检测装置的设计方法。并在文中详细介绍了光源设计、照度探测器设计、控制电路设计以及试验等研制过程,最终研制成功的新型CCD摄像机照度检测装置实现了光源的均匀辐射、自动调光等功能,适用于各类CCD摄像机1.0×10-1lx~1.0×105lx照度范围的检测。     

近场照度均匀的LED阵列设计

通过分析多颗LED组成的各种阵列在近场平面上的照度分布,来设计可实现近场照度均匀的LED排列方式和距离。基于LED的光强分布,构建单颗LED的光强分布模型（并非朗伯分布）,给出了方程和等式用于计算不同排列方式下的LED分布距离和封装密度,以实现近场平面上的照度均匀。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.