淀粉接枝丙烯酸/醋酸乙烯酯高吸水性树脂的制备

以过硫酸铵为引发剂,N,N-亚甲基双丙烯酰胺为交联剂,淀粉与丙烯酸/醋酸乙烯酯混合单体通过接枝共聚,制备了吸水及耐盐性能均较好的淀粉接枝丙烯酸/醋酸乙烯酯高吸水性树脂(CGAV)。最佳工艺条件为:淀粉10.0 g,m(混合单体)∶m(淀粉)=4∶1,w(引发剂)=0.3%,w(交联剂)=0.05%,于45℃反应2h~3 h。在最佳工艺条件下制得的CGAV吸去离子水率760 g.g-1,吸0.9%NaC l水溶液率68 g.g-1。     

聚乙烯与丙烯酸的溶液接枝聚合

以过氧化苯甲酰为引发剂，二甲苯为溶剂，进行了丙烯酸与低密度聚乙烯的溶液接枝聚合，研究了ＢＰＯ用量、溶液浓度以及丙烯酸用量对接枝率的影响。聚乙烯接枝了丙烯酸后与铝的粘结强度显著增大，当接枝率为７．２％时，剥离强度由未接枝时的１９３Ｎ／ｍ，提高到９８４Ｎ／ｍ。     

电子束预辐照聚丙烯与丙烯酸的接枝共聚合

应用电子束预辐照的方法对丙烯酸与等规聚丙烯粉末的接枝共聚合进行了研究．讨论了辐照剂量、储藏时间、反应温度、Ｍｏｈｒ’ｓ 盐浓度及单体浓度等因素对接枝率的影响（ 所有的实验,辐照及接枝聚合等都是在有氧的条件下进行的） ．同时对接枝材料对金属离子的吸附性能作了初步的探讨．结果表明,接枝聚合可以在有氧的条件下顺利进行．接枝材料在离子吸附方面有较大的应用前景．     

微波法合成淀粉接枝丙烯酸盐类高吸水性树脂的研究

以N,N′-亚甲基双丙烯酰胺为交联剂、过硫酸铵为引发剂、在微波辐照下对淀粉接枝丙烯酸盐共聚进行了系统的研究,确定了最佳的反应条件,合成了粉末状的高吸水性树脂。并用FTIR和固体NMR等方法探讨了淀粉一丙烯酸盐接枝共聚物的结构特征。实验结果表明,利用微波技术合成淀粉一丙烯酸盐接枝共聚物可实现一次合成、干燥,简化合成工艺。淀粉与丙烯酸盐质量比为40／100左右时产物的接枝率最大,且吸水速率明显高于化学法合成的高吸水树脂。     

富含纤维素类农作物秆与丙烯酸接枝共聚制备高倍率吸水树脂

用棉花秆、麦秆和玉米秆等富含纤维素类农作物秆与丙烯酸接枝共聚制备了高倍率的吸水树脂. 研究了不同水质(去离子水、自来水及雨水)对接枝产物吸水性能的影响. 采用棉花秆、麦秆、玉米秆与丙烯酸的接枝产物对去离子水的吸水倍率分别为930, 790和630 g/g, 对自来水的吸水倍率分别为670, 350和250 g/g, 用玉米秆/地瓜淀粉混合物制备的接枝产物对雨水的吸水倍率为540 g/g. 为棉花秆、 麦秆及玉米秆等富含纤维素的农作物秆的深加工与应用开辟了一条途径.     

预辐照聚乙烯醇纤维与N,N′-亚甲基双丙烯酸酰胺的接枝、交联

接枝共聚交联;60Co辐照;预辐照聚乙烯醇纤维与N;N′-亚甲基双丙烯酸酰胺的接枝、交联     

甲基丙烯酸丁酯接枝纤维素的制备

为开发纤维素基吸油材料,以棉浆粕为基材、甲基丙烯酸丁酯(BMA)为单体、乙二醇二甲基丙烯酸酯为交联剂,采用悬浮接枝聚合法合成了BMA接枝纤维素的聚合物。采用红外光谱(FT-IR)、X射线衍射(XRD)、扫描电镜(SEM)、热重(TG)、差热(DSC)等手段对所得吸油材料结构进行了表征。考察了引发剂的种类及用量、接枝单体及交联剂用量、反应温度、反应时间等因素对BMA接枝纤维素聚合物的接枝聚合反应性能及吸油性能的影响。结果表明:当m(棉浆粕)∶m(K2S2O8)∶m(BMA)∶m(乙二醇二甲基丙烯酸酯)=1∶0.025∶1.5∶0.005,75℃下恒温反应6 h,合成的BMA接枝纤维素的接枝率最高(36.2%),均聚物含量相对较低(5.8%),且吸油性能优良。     

丙烯酸乙酯^60Co辐照下形成的过氧化物及其引发活性

丙烯酸乙酯经在空气下６０Ｃｏγ辐照后,剂量率在１５Ｇｙ／ｓ以上时可形成３种过氧化物组份,各组份的分布随剂量率的不同而异;当剂量率为１０Ｇｙ／ｓ时,只形成单一的相当于第２组份的过氧化物．用红外光谱,核磁共振谱和质谱测定了３种过氧化物组份的结构．具有交替结构的第２组份有较强的引发活性,能引发其它乙烯类单体聚合,与Ｋ２Ｓ２Ｏ８相比,它能在较低温度和较短时间内引发聚合,且聚合过程更平稳,获得的聚合物分子量更高．     

预辐照接枝丙烯酸、苯乙烯磺酸钠对聚全氟乙丙烯膜性能的影响

采用常温下γ射线预辐照引发接枝的方法,在聚全氟乙丙烯(FEP)上接枝了丙烯酸(AA)和对苯乙烯磺酸钠(SSS),制备了一种含羧酸基团和磺酸基团的接枝膜.傅立叶变换红外光谱(FT-IR)分析证明了磺酸基团和羧酸基团的成功引入.采用XRD、TGA和接触角研究了接枝率对FEP膜的结晶度、热学特性及亲水性等性能的影响.结果表明,随着制备的FEP膜接枝率的增加,膜的结晶度、热稳定性和接触角逐渐减小;与此相反,FEP膜的亲水性能随接枝率的增加而增加.接枝膜湿敏性能测定结果表明,在相对湿度从5%RH变化到98%RH时,接枝膜电阻线性变化范围接近3个数量级,具有响应速度快(吸附<1min,解吸<2min),湿滞小(<3%RH)的特点,具有应用于电阻型湿度传感器的广阔前景.     

纤维素与己内酰胺的接枝共聚反应

以过硫酸铵和过硫酸钾为引发剂,在碱性环境下进行纤维素与己内酰胺的接枝共聚反应.采用红外光谱仪(FT-IR)、扫描电子显微镜(SEM)及X射线衍射仪(XRD)对接枝共聚物的分子结构、表观形貌和结晶性进行了表征.通过单因素实验重点考察了单体用量、引发剂浓度、反应温度和反应时间等对接枝共聚物接枝率的影响.结果表明:以3 g纤...     

Chemically initiated graft copolymerization of acrylic acid onto acrylonitrile-butadiene-styrene (ABS) terpolymer and its constituent polymers

The graft copolymerization of acrylic acid onto acrylonitrile-butadiene-styrene terpolymer (ABS), has been initiated by the use of both benzoyl peroxide and azobisisobutyronitrile. Addition occurs in the butadiene region of the polymer, either by the loss of a vinylic hydrogen and subsequent radical formation and addition of monomer or by addition to the double bond. The amount of acrylic acid which may be added is dependent upon the time and temperature of the reaction and the concentration of monomer and initiator. Thermal analysis of the grafted samples show that the residue is less than that expected based upon the composition of the copolymer; similar results have been previously obtained for acrylic acid grafted by another technique. © 1996 John Wiley & Sons, Inc.     

Synthesis and characterization of SPE membrane based on sulfonated FEP‐g‐acrylic acid by radiation induced graft copolymerization for PEM fuel cell

A Novel solid polymer electrolyte (SPE) membrane containing both ? COOH and ? SO₃H group has been prepared by simultaneous method of radiation grafting of acrylic acid onto FEP followed by sulfonation. The presence of weakly acidic acrylic acid controls the swelling in water while ? SO₃H group provides conductivity due to its strongly ionic characteristic. FEP‐g‐acrylic acid and its sulfonated derivatives were characterized by their properties. While the mechanical properties decreased, other properties such as ion exchange capacity (IEC), water uptake and ionic conductivity increased with increase in graft content. These properties further changed on sulfonation. Acrylic acid being weakly acidic in nature, conductivity values of the grafted membrane were quite low. However, introduction of strong ? SO₃H group resulted in conductivity closer to Nafion 117. Few sulfonated membranes have been tested with respect to H₂/O₂ fuel cell performance. Short‐term fuel cell test for 100 hr gave a stable performance. These membranes are less expensive compared to Nafion. Copyright © 2004 John Wiley & Sons, Ltd.     

Preparation and characterization of a homobifunctional silicone rubber membrane grafted with acrylic acid via plasma-induced graft copolymerization

Polyacrylic acid (PAA) was grafted onto the surface of silicone rubber membrane (SR) by plasma-induced graft copolymerization (PIP). Ar-plasma was used to activate the surface of SR. Also, a determination was made of the influences of plasma treatment power, pressure, time, grafted copolymerization reaction time, and monomer concentration on polymerization yield. The surface properties of SR were measured by ATR-FTIR, ESCA, and SIMS. In those analyses, the elemental composition and different carbon bindings on the surface of SR were examined by ESCA with the amount of O1s/C1s being approximately 0.7 at 60 s by Ar-plasma treatment (60 W, 200 mtorr). The peroxide group introduced on SR was measured via 1,1-diphenyl-2-picryhydrazyl (DPPH). The optimum amount of peroxide groups was 6.85 × 10⁻⁸ mol/cm² at 60 s of Ar-plasma treatment. The peroxide group (33D peak) was introduced onto the surface of SR by negative spectra of SIMS analysis after SR treatment by Ar-plasma. An increase was obtained in grafted polymerization yield with a region of 5 to 50% (v/v) of acrylic acid aqueous solution. Both sites of polyacrylic acid were detected after staining by toluidine blue O. That is, a homobifunctional membrane was developed via this surface modification method. © 1996 John Wiley & Sons, Inc.     

Production of Poly(acrylic acid) Particles Dispersed in Organic Media

Summary: A process for preparation of poly(acrylic acid) particles dispersed in oil is presented. The process comprises two steps: the first step involves the preparation of a poly(acrylic acid) solution, while the second step consists in the preparation of the polymer particles by dispersing the polymer solution in an organic phase. During the second step, modification of the polymer chain structure can be performed through chemical reactions. One of the advantages of the proposed process is the possibility to produce particles loaded with drugs or other chemical compounds. Besides that, if the continuous phase is vegetable oil, purification of the reaction medium may not be necessary.     

磁性壳聚糖-聚丙烯酸微球的制备及表征

壳聚糖通过与丙烯酸接枝共聚制得壳聚糖聚丙烯酸悬浮液,在铁磁流体(Fe3O4)与聚乙二醇(分散剂)存在下通过与戊二醛交联,制备了磁性壳聚糖聚丙烯酸微球。用扫描电镜、红外光谱对合成的高分子微球进行形貌观察和结构表征,并进行了元素分析和磁性能测试,研究了磁性微球对牛血清白蛋白(BSA)的吸附效果。结果表明,合成的磁性微球外表呈球形,粒径为100～400nm;当Fe含量为2.47%时,磁性微球的饱和磁化强度约为1.30emug,磁矫顽力为280Oe,磁化率为2.16×10-4(常温下),属于顺磁性材料;其对BSA有较好的吸附效果,饱和吸附量约为400mgg。     

Controlled polymerization of acrylic acid under 60Co irradiation in the presence of dibenzyl trithiocarbonate

The polymerization of acrylic acid (AA) was performed under ⁶⁰Co irradiation in the presence of dibenzyl trithiocarbonate at room temperature, and well‐defined poly(acrylic acid) (PAA) with a low polydispersity index was successfully prepared. The gel permeation chromatographic and ¹H NMR data showed that this polymerization displays living free‐radical polymerization characteristics: a narrow molecular weight distribution (M_w/M_n = 1.07–1.22), controlled molecular weight, and constant chain‐radical concentration during the polymerization. Using PAA? S? C(?S)? S? PAA as an initiator, the extension reaction of PAA with fresh AA was carried out under ⁶⁰Co irradiation, and the results indicated that this extension polymerization displayed controlled polymerization behavior. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3934–3939, 2001     

Effect of pH on Poly(acrylic acid) Solution Polymerization

The free-radical redox-initiated aqueous solution polymerization of fully and partially neutralized acrylic acid was carried out at room temperature under full exposure to air. The effect of neutralization degree on the polymerization rate and product properties was studied. Increasing neutralization of the reaction mixture with sodium hydroxide resulted in greater conversion of acrylic acid to sodium acrylate. The rate of polymerization, determined from a gravimetric off-line water removal technique, was shown to decrease significantly with decreasing degree of neutralization. Molecular weight also decreased with decreasing degree of neutralization. The glass transition temperature and hydrophilicity of the polymer product decreased with increasing degree of neutralization. In-line infrared monitoring was also used to monitor the reaction progress and was shown to be an effective tool for this purpose.     

The synthesis and characterization of monodisperse poly(acrylic acid) and poly(methacrylic acid)

A number of polyacrylic (PAA) and polymethacrylic (PMAA) acids have been synthesized by living anionic polymerization of the monomeric tert-butyl esters followed by subsequent hydrolysis of the corresponding polyesters. The necessary precautions were taken in order to assure good molecular weight control, as well as high yields in the polymerization reactions. The intermediate and final polymers were characterized by gel permeation chromatography and NMR-H¹ spectrometry.     

Oxidation of polyethylene surface by glow discharge and subsequent graft copolymerization of acrylic acid

Plasma-induced graft copolymerization of acrylic acid, which was incorporated into PE films, was investigated here. The influence of plasma conditions such as plasma treatment gases, power, pressure, time, monomer concentration, and graft copolymerization time on polymerization yield was determined. The samples were characterized by ESCA, IR, and water contact angle. A respective chemical shift of the C1s signal of Ar or O₂ plasmatreated and untreated PE films was revealed by ESCA, in which the presence of the grafted PAAc was also verified. An increase in polymerization yield with plasma treatment duration and power was found. That the grafted copolymerization was limited to a very thin surface region was revealed by optical microscopy on the cross section of the grafted film. © 1993 John Wiley & Sons, Inc.