W-SBA-15介孔分子筛的直接合成及其对环己烯环氧化反应的催化性能

 分别以Na2WO4和H2WO4为钨源,以正硅酸四乙酯为硅源直接合成了W-SBA-15介孔分子筛样品,并用小角XRD,N2吸附,FT-IR,UV-Vis,SEM和XRF等手段对合成的分子筛进行了表征. 结果表明,只用P123(EO20PO70EO20)为模板剂时,分子筛中钨的含量只是投料量的一半; 而以P123和十六烷基三甲基溴化铵为混合模板剂时,钨能有效地掺杂到SBA-15分子筛中. 当原料中的Si/W摩尔比为40时,W-SBA-15分子筛中的钨物种以高度分散状态存在,且以H2WO4为钨源比以Na2WO4为钨源更易将钨掺杂到SBA-15介孔分子筛中. W-SBA-15分子筛催化剂对环己烯环氧化反应具有较高的催化活性.     

氧化钨介孔材料的制备与表征

以介孔二氧化硅(KIT-6)为硬模板, 硅钨酸为钨源, 用硬模板法制备WO3-SiO2复合材料, 再利用HF除去二氧化硅, 得到了介孔三氧化钨材料. 用X射线衍射(XRD)、能量扩散X射线(EDX)、高分辨透射电镜(HRTEM)、N2吸附-脱附等表征手段, 对制备复合材料的物料比、煅烧温度以及不同分散剂等条件进行了考察. 结果表明, 硅钨酸与硅介孔的物料比(m(WO3)/m(SiO2))在3:1到4:1之间, 在600-750 ℃下煅烧, 能制备结构较好的介孔氧化钨. 乙醇和蒸馏水为分散剂时, 用乙醇为分散剂所得的介孔WO3材料具有更高的比表面积和孔体积.     

WxC/SBA-16催化剂的制备、表征及催化加氢脱硫性能

以正硅酸乙酯为硅源, 仲钨酸铵为钨源, P123和F127为混合模板剂,采用水热晶化法一步合成了不同钨含量(以n(Si):n(W)表示)的WO3/SBA-16, 然后经甲烷/氢气(V(CH4)/V(H2)=1/4)混和气体程序升温还原碳化(TPC), 制备出了WxC/SBA-16(x=1, 2)催化剂. 采用XRD、N2-吸附/脱附、TEM和FTIR等分析测试技术对样品的结构进行了表征, 并以噻吩作为模型化合物, 对WxC/SBA-16催化剂的加氢脱硫催化活性进行了评价. 结果表明, 在一定钨含量的条件下, WO3/SBA-16和WxC/SBA-16样品仍然保持立方笼状介孔结构, 当n(Si):n(W)为30-10时, 碳化钨的物相为W2C; n(Si):n(W)为7.5时, 碳化钨的物相为W2C和WC. WxC/SBA-16催化剂表现出了良好的加氢脱硫催化性能.     

二维六方p6mm有序介孔WO_3-TiO_2复合材料的制备及其可见光光催化性能

以非离子型表面活性剂为模板剂,采用蒸发诱导自组装法制备了一系列不同WO3含量的有序介孔WO3-TiO2复合材料,并表征了其孔结构、形貌、孔隙率、光谱性质及组成.结果表明,该材料呈二维六方p6mm对称和锐钛矿晶相结构;与无序WO3-TiO2复合材料相比,其比表面积(152～154m2/g)更大,孔径更均一(5.3nm),且比纯TiO2的帯隙宽度(3.0eV)更窄.将该WO3-TiO2样品用于可见光光催化降解水相中罗丹明B和2,4-二氯苯氧乙酸的反应中,发现WO3含量适当的有序介孔WO3-TiO2样品的光催化活性比无序的样品和纯TiO2的更高.     

不同载体对负载型氧化钨催化剂在己二酸合成反应中的结构及性能影响

以SBA-15、六角介孔二氧化硅(HMS)和SnO2为载体,通过浸渍法合成了含钨负载型催化剂,并考察了三种催化剂在环氧环己烷选择氧化制备己二酸反应中的催化性能.通过X射线衍射(XRD),透射电镜/场发射透射电镜(TEM/FETEM),紫外-可见漫反射光谱(UV-Vis DRS),拉曼(Raman)光谱,X射线光电子能谱(XPS)以及傅里叶变换红外(FTIR)光谱等手段对各种催化剂的结构进行表征.结果表明,载体与催化剂的性能有密切的关系.以SnO2为载体的WO3/SnO2催化剂活性最高,其次是WO3/HMS催化剂,WO3/SBA-15催化剂的活性最差.XRD分析显示WO3/SnO2催化剂中氧化钨物种的晶化程度最低,TEM和XPS结果表明氧化钨物种在WO3/SnO2催化剂表面高度分散并且粒径尺寸很小(约2 nm),UV-Vis DRS结果表明在WO3/SnO2催化剂中存在孤立[WO4]四面体和低聚态的钨物种,这些物种的存在可能是WO3/SnO2催化剂具有高活性的主要原因.此外,WO3/SnO2催化剂可以重复使用多次,6次反应后己二酸(AA)得率仍然保持在80%以上,说明氧化钨物种与SnO2载体间存在强烈的相互作用,从而提高了催化剂的稳定性.     

高效WO3掺杂MCF催化剂的合成及其在环戊烯选择氧化制戊二醛反应中的应用

以钨酸钠和正硅酸乙酯为前驱体直接合成高含量WO₃掺杂介孔氧化硅泡沫(MCF)催化剂. 在773 K焙烧后显示出更高的热稳定性. 小角X射线散射, N₂-物理吸附和透射电子显微镜结果表明钨物种嵌入后, 材料仍保持MCF特征的三维织构介孔特征. 紫外拉曼和紫外可见漫反射光谱结果表明钨物种主要以孤立的或者低聚态的氧化钨形式存在, 所以在氧化钨质量分数(w)低于20%时氧化钨物种能够高度分散在载体上. 在环戊烯选择氧化制戊二醛反应中, 反应16 h 后环戊烯的转化率达到100%, 戊二醛的产率达到83.5%. 催化剂重复利用实验表明催化剂的稳定性较好, 没有钨物种的脱落. 这种优异的催化性能归结于合适的氧化钨含量和高分散的钨物种.     

新型HPWs@MIL-101催化剂的制备、表征及其催化性能

采用直接合成法将磷钨杂多酸(HPWs)固载到金属-有机骨架材料MIL-101的介孔笼中,制得新型HPWs@MIL-101多相催化剂。利用XRD、N2吸附、扫描电镜(SEM)、XPS、UV-Vis DRS、Raman和FT-IR等手段对该催化剂进行了表征,并研究了其在环戊烯选择氧化制备戊二醛反应中的催化性能。结果表明,磷钨杂多酸高度分散在金属-有机骨架MIL-101的介孔笼中,将磷钨杂多酸固载到MIL-101上后,能够很好地保持磷钨杂多酸的Keggin结构和载体MIL-101的晶体骨架结构。HPWs@MIL-101催化剂的催化性能远高于传统浸渍法制备的催化剂的催化性能,当磷钨杂多酸的负载量为12.5%(w)时,HPWs@MIL-101表现出最优的催化性能,环戊烯转化率高达100%,戊二醛的得率达到78.7%。重复实验表明该催化剂具有较高的稳定性,使用三次后,GA的得率仍然达到74.1%。     

一步法合成具有高效傅式烷基化催化性能的铁功能化有序介孔催化剂

以阴离子表面活性剂十二烷基硫酸钠(SDS)为模板, 一步合成了金属铁离子功能化的介孔二氧化硅催化剂(FeMS). 表征结果显示, FeMS催化剂具有六方结构的一维直孔道, 孔径约为3.5 nm, 其中铁离子以四配位形式高度分散于主体二氧化硅骨架上, 并且掺杂后的样品仍保持了主体二氧化硅有序的介孔结构. 铁离子的掺杂量可以通过反应物中硝酸铁的含量进行调变. 在苯与苄基氯的傅式烷基化反应中, FeMS催化剂显示出良好的催化活性与稳定性. 随着铁掺杂量的增加, FeMS的催化活性逐渐提高. 其中FeMS(40)样品可以在2 min内完成催化反应, 二苯甲烷的选择性为100%. 这种良好的催化性能主要是由于该催化剂具有高度分散的铁离子活性位点、较大的比表面积和孔体积以及空旷的骨架结构所致.     

一步法制备含W介孔碳材料及其氧化脱硫性能研究

以钨酸钠为钨源,以乙二胺四乙酸二钠为碳源经过高温煅烧制备了含W的介孔碳材料,采用XRD、SEM、FT-IR、BET对含钨的介孔碳材料进行表征。结果表明,煅烧后介孔碳材料的表面形成了粒状含有结晶水的氧化钨(WO_3·H_2O)。相比于纯的介孔碳材料,含钨介孔碳材料的总比表面积减小。以含W介孔碳材料为催化剂,H_2O_2作为氧化剂,1-丁基-3-甲基咪唑氟硼酸盐([BMIM][BF_4])离子液体作为萃取剂,组成萃取-催化氧化脱硫体系(ECODS)并研究其对模拟油中二苯并噻吩脱除效果。考察了氧化钨负载量、反应温度、H_2O_2加入量、催化剂用量、离子液体用量以及不同类型硫化物对二苯并噻吩脱除的影响。在最佳反应条件下,催化剂对二苯并噻吩(DBT)、4,6-二甲基二苯并噻吩(4,6-DMDBT)、苯并噻吩(BT)、噻吩(TH)和真实汽油的脱除率分别达到98.6%、65.6%、61.2%、57.8%和64.3%。催化剂回收利用五次之后脱硫率略有降低,仍高达95.2%。     

空心介孔WO3球的制备及光催化性能

采用喷雾干燥法制备中空偏钨酸铵球,通过调整热处理温度制备空心介孔WO3球。结果表明:具有Keggin结构的[H2W12O40]6-金属簇的破坏温度区间为417~439℃;在热处理温度为500、550℃,仍有少量的铵根和结合水没有分解,除了WO3外,还存在(NH4)0.06WO3(H2O)0.11;当热处理温度在600℃以上时,偏钨酸铵完全分解为WO3;热处理温度为700℃,保温时间为2h,得到空心介孔WO3球。其形成机理为:空心的偏钨酸铵球,在热处理过程中由于各亚晶的位向不一致,各亚晶沿着[002]晶向择优生长,亚晶形成狭长颗粒,从而在空心球表面形成了介孔;但当热处理温度为800℃,保温时间为2 h,晶粒与晶粒之间通过合并而长大,孔道也随之消失;空心介孔WO3球具有良好的光催化效果,500 W高压汞灯照射150 min甲基蓝的降解率为65.9%。     

Platinum/mesoporous WO3 as a carbon-free electrocatalyst with enhanced electrochemical activity for methanol oxidation

A new type of carbon-free electrode catalyst, Pt/mesoporous WO3 composite, has been prepared and its electrochemical activity for methanol oxidation has been investigated. The mesoporous tungsten trioxide support was synthesized by a replicating route and the mesoporous composties with Pt loaded were characterized by using X-ray diffraction (XRD), nitrogen sorption, field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS) techniques. Cyclic voltammetry (CV), line scan voltammetry (LSV) and chronoamperometry (CA) were adopted to characterize the electrochemical activities of the composites. The mesoporous WO3 showed high surface area, ordered pore structure, and nanosized wall thickness of about 6-7 nm. When a certain amount of Pt nanoparticles were dispersed in the pore structure of mesoporous WO3, the resultant mesostructured Pt/WO3 composites exhibit high electro-catalytic activity toward methanol oxidation. The overall electro-catalytic activities of 20 wt % Pt/WO3 composites are significantly higher than that of commercial 20 wt % Pt/C catalyst and are comparable to the 20 wt % PtRu/C catalyst in the potential region of 0.5-0.7 V. The enhanced electro-catalytic activity is attributed to be resulted from the assistant catalytic effect and the mesoporous structure of WO3 supports.     

Development of a high-performance anode for lithium ion batteries using novel ordered mesoporous tungsten oxide materials with high electrical conductivity

An ordered mesoporous WO(3-X) with high electrical conductivity (m-WO(3-X)) was prepared and evaluated as an anode material for lithium ion batteries (LIBs). Ordered mesoporous tungsten trioxide (m-WO(3)) with an identical pore structure to that of m-WO(3-X) and bulk WO(3-X) (b-WO(3-X)) was prepared for the comparison purpose. An m-WO(3-X) electrode exhibited a high reversible capacity (748 mAh g(-1), 6.5 Li/W) and a high volumetric capacity (～1500 mAh cm(-3)), which is comparable to the Li metal itself (ca. 2000 mAh cm(-3)). Also, an improved rate capability and a good cyclability were observed in the m-WO(3-X) electrode when compared with m-WO(3) and b-WO(3-X) electrodes. From electrochemical impedance spectroscopy (EIS) analysis, the advanced anode performance of the m-WO(3-X) electrode was probably attributed to large ordered mesopores and a high electrical conductivity. Differential scanning calorimetry (DSC) result displayed that the safety of m-WO(3-X) was more improved than those of graphite and Si anode materials.     

Template-free synthesis and characterization of mesoporous tungsten nitride nanoplates

We report well-defined mesoporous β-W(2)N nanoplates prepared by using layered WO(3)·H(2)O without templates. The tungsten nitride nanoplates exhibit typical mesoporous structures with size-controlled monomodal pore distributions.     

Facile in situ synthesis of the bismuth oxychloride/bismuth niobate/TiO(2) composite as a high efficient and stable visible light driven photocatalyst

Fe-ions modified mesoporous Bi(2)WO(6) nanosheets (Fe-Bi(2)WO(6)) were successfully synthesized via a simple two-step method, which involved a template-free hydrothermal process and a following impregnation treatment. The resultant products were characterized by XRD, TEM, XPS, EDX, ESR, UV-Vis, PL, and visible light photocatalytic measurements. Experimental results indicated that the addition of a small amount Fe-ions (optimized content at 0.1 wt.%) could evidently improve the activity of Bi(2)WO(6). The apparent reaction rate of Fe-Bi(2)WO(6)-0.1% (k, 0.099 min(-1)) was 3.2 times higher than that of Fe-Bi(2)WO(6)-0% (k, 0.031 min(-1)). The Fe-ions mainly existed as Fe(3+) and Fe(2+) ions, which were uniformly distributed on the surface of Bi(2)WO(6) nanosheets and some Fe(3+)-ions substituted Bi(3+)-ions in Bi(2)O(2) layers. Both of the concentration and state of Fe-ions played vital factors for the improved visible light photocatalytic activities.     

Acidity of mesoporous MoO(x)/ZrO2 and WO(x)/ZrO2 materials: a combined solid-state NMR and theoretical calculation study

The acidity of mesoporous MoO(x)/ZrO2 and WO(x)/ZrO2 materials was studied in detail by multinuclear solid-state NMR techniques as well as DFT quantum chemical calculations. The 1H MAS NMR experiments clearly revealed the presence of two different types of strong Br?nsted acid sites on both MoO(x)/ZrO2 and WO(x)/ZrO2 mesoporous materials, which were able to prontonate adsorbed pyrine-d5 (resulting in 1H NMR signals at chemical shifts in the range 16-19 ppm) as well as adsorbed trimethylphosphine (giving rise to 31P NMR signal at ca. 0 ppm). The 13C NMR of adsorbed 2-(13)C-acetone indicated that the average Br?nsted acid strength of the two mesoporous materials was stronger than that of zeolite HZSM-5 but still weaker than that of 100% H2SO4, which was in good agreement with theoretical predictions. The quantum chemical calculations revealed the detailed structures of the two distinct types of Br?nsted acid sites formed on the mesoporous MoO(x)/ZrO2 and WO(x)/ZrO2. The existence of both monomer and oligomer Mo (or W) species containing a Mo-OH-Zr (or W-OH-Zr) bridging OH group was confirmed with the former having an acid strength close to zeolite HZSM-5, with the latter having an acid strength similar to sulfated zirconia. On the basis of our NMR experimental and theoretical calculation results, a possible mechanism was proposed for the formation of acid sites on these mesoporous materials.