n型Bi_2Te_(3-y)Se_y温差电材料薄膜的电化学制备及表征

采用电化学控电位的方法在不锈钢基片上电沉积制备了Bi2Te3-ySey温差电材料薄膜。研究了电沉积溶液中硒含量与薄膜中硒含量的关系,考察了不同沉积电位对电沉积Bi2Te3-ySey薄膜的温差电性能的影响,并采用ESEM、EDS、XRD等方法对电沉积薄膜的形貌、成分及结构进行了分析。结果表明,在含有Bi3 、HTeO2 和Se4 的电沉积溶液中,采用电化学沉积的方法,可实现铋、碲、硒三元共沉积,生成Bi2Te3-ySey半导体化合物。改变电沉积溶液组成,可控制Bi2Te3-ySey化合物中硒的掺杂浓度。-0.04V沉积电位下制备的Bi2Te3-ySey薄膜较平整、致密,组成为Bi2Te2.7Se0.3。退火处理可提高电沉积Bi2Te3-ySey薄膜的塞贝克系数,且控制沉积电位为-0.04V下制备的Bi2Te3-ySey薄膜退火后的塞贝克系数为-123μV·K-1。     

NiOxHy薄膜的电致变色特性和机理

运用循环伏安和阶跃电位方法研究了Ni（OH）2粉末靶直流溅射沉积的NiOxHy薄膜电致变色特性．结合实时的光透射-时间变化，发现着色后的薄膜在零外电势下有一自发的消色过程，该过程可能对应着Li 的自发注入。着色没有自发过程，获取了着消色状态Ni2p3／2和O1s的XPS谱，表明在着色态镍被氧化，消色态镍被还原，相应地氧的化学环境发生改变．     

纳米Al_2O_3颗粒对镍电结晶过程的影响

借助循环伏安(CV)和计时安培(CA)研究了在不同电位下,纳米Al2O3微粒对镍由硫酸盐混合溶液在铜基底上电结晶沉积的影响.结果表明,Ni-Al2O3镀液体系电沉积的起始电位约为-740 mV.随着阶跃电位负移,Ni-Al2O3镀液体系电沉积成核时间tm逐渐缩短.与纯Ni镀液体系电沉积的tm相比,在-740~-830mV较低阶跃电位下,Ni-Al2O3镀液体系电沉积的成核时间tm明显缩短,表明Al2O3微粒有助于镍的电结晶成核.在-890 mV阶跃电位下,Ni-Al2O3镀液体系电沉积初始阶段的成核过程满足Scharifker-Hills三维瞬时成核模型.     

Bi2Mn0.1V0.9O5.35-δ薄膜的制备与性能研究

以Bi(NO3)3·5H2O、NH4VO3和Mn(CH3COO)2· 4H2O为原料,采用溶胶凝胶法在LaNiO3(LNO)/Si(100)衬底上制备了Bi2 Mn0.1 V0.9O5.35-δ (BIMNVOX.10)薄膜,并通过X射线衍射(XRD)、扫描电镜(SEM)和原子力显微镜(AFM)研究了薄膜的晶体结构和形...     

双波长催化动力学光度法间接测定痕量Bi(Ⅲ)

研究了在H2SO4介质中,利用Bi(Ⅲ)可定量置换出Cu(Ⅱ)-EDTA中的Cu(Ⅱ),而Cu(Ⅱ)可催化H2O2同时氧化甲苯胺蓝和中性红褪色反应,通过测量524nm和630nm波长下的吸光度的变化,建立了双波长催化动力学分光光度法间接测定痕量Bi(Ⅲ)的新方法。方法的线性范围为0.00200~0.110μg/25mL,检出限为4.1×10-11 g/mL。用于药物中铋的测定,结果满意。     

紫外光照下纳米TiO2电极的电化学行为

通过电沉积方法制备了纳米TiO2薄膜电极，应用循环伏安和交流阻抗技术研究了TiO2电极在253.7 nm的紫外光照射下的电化学行为.结果表明, TiO2薄膜电极的循环伏安图在＋0.15 V处出现新的氧化峰,交流阻抗谱的半圆明显减小，电极的开路电位在有光和无光的情况下呈现规律变化.实验证实在紫外光照射下电极表面有新物种Ti3＋生成，但光生Ti3＋不稳定.     

3-氨基苯硼酸-苯胺在ITO玻璃上的电聚合及对维生素C的光学响应

在硫酸介质中,以氧化铟锡(ITO)透明导电玻璃为载体,利用循环伏安法制备3-氨基苯硼酸-苯胺共聚物膜,研究了该薄膜对维生素C(AA)的光学响应.结果表明,利用电聚合方法可在ITO玻璃表面形成均匀致密的蓝色3-氨基苯硼酸-苯胺共聚物薄膜,薄膜的厚度可通过控制电位循环圈数来进行调节,薄膜使用后可用恒电位法和循环伏安法进行再生;在3%HAc介质中,在2.0～17.5mg·L-1范围内薄膜对AA浓度的变化产生灵敏的光学响应,且在480～750nm波长范围内随着波长的增加响应的灵敏度增加.     

电化学还原预处理对BiVO_4薄膜电极光电化学氧化水性能的提高

在酸性水溶液中(pH=2.0),采用电化学还原(ER)方法对BiVO4薄膜电极进行预处理,并探讨了其对薄膜电极光电化学氧化水性能的影响.结果表明,这种预处理可显著提高电极的光电化学氧化水的性能,且具有良好的光电化学稳定性.利用扫描电子显微镜、X射线衍射、拉曼光谱、光电子能谱、紫外-可见漫反射光谱、荧光光谱、电化学阻抗谱及Mott-Schottky等方法对ER处理前后的电极进行了表征.结果表明,ER预处理使电极粗糙度增大,表面积增大约1.4倍;电极材料的晶型无明显变化,但V—O对称伸缩振动略有红移;表面Bi,V和O结合能变小,Bi3+部分被还原,Bi/V原子比增大;ER处理导致电极平带电位负移,光生载流子在薄膜电极/溶液界面转移速率加快,表面复合速率降低.这些变化和表面积增加是BiVO4电极光电化学性能提高的主要原因.     

CuInSe_2薄膜的电化学沉积及其形成机理

采用电化学沉积法制备了太阳电池用CuInSe2薄膜.利用循环伏安法(CV)、X射线能谱(EDS)和X射线衍射技术(XRD)研究了电沉积过程中CuInSe2的形成机理,并研究了制备工艺对膜层成分、形貌和物相结构的影响.研究结果表明,铟进入固相是通过In3+受Cu3Se2诱导作用欠电势还原或者In3+与H2Se反应这两种途径实现;先沉积的Cu3Se2与新生成的铟或铟硒化合物反应最后生成CuInSe2.在阴极电位为-0.58~-0.9 V(vs.SCE)时出现了不随电位变化的极限还原电流,在该电位范围内进行电沉积获得了化学计量组成稳定可控且相对致密平整的CuInSe2薄膜.电沉积的CuInSe2薄膜经真空退火处理后结晶质量得到明显改善.     

原位溶解-沉积法制备高可见光活性BiOI/Bi2O3光催化剂

以Bi2O3为前驱体,通过原位溶解-沉积法在KI溶液中制备了BiOI/Bi2O3光催化剂。用X射线衍射(XRD)、扫描电子显微镜(SEM)和紫外-可见漫反射光谱(UV-Vis DRS)等对样品进行了表征。结果表明Bi2O3球形颗粒紧密地贴在BiOI片上。随着KI溶液pH值的降低,Bi2O3逐渐转变为BiOI,且样品的吸收带边逐渐红移。在可见光(λ≥420 nm)下降解甲基橙,在pH=3下制备的BiOI/Bi2O3的活性最强,其原因是BiOI/Bi2O3 p-n异质结促进了光生载流子的分离。     

聚苯胺电致变色薄膜在不同颜色区间的电化学循环稳定性研究

本文采用电位阶跃和循环伏安法结合紫外可见光光度法研究了聚苯胺薄膜的电致变色性质. 聚苯胺薄膜颜色多变,颜色在浅黄色到绿色再到蓝色之间变化,本文研究在不同的颜色变化区间内聚苯胺薄膜的电化学循环稳定性. 研究结果表明,薄膜在黄色到蓝色(0.4 V ~ 1.2 V)以及绿色到蓝色(0.8 V ~ 1.2 V)区间变化时,电致变色循环性能较差,而在黄色和绿色(0.4 V ~ 0.8 V)之间变化时循环稳定性能良好,着色时间为4.5 s,着色效率高达159.48 cm²·C^-1.     

Electrochromic multilayer films of tunable color by combination of copper or iron complex and monolacunary dawson-type polyoxometalate

Electrochromic multilayer films consisting of polyoxometalate (POM) cluster alpha-K(10)[P(2)W(17)O(61)].17H(2)O (P(2)W(17)), copper(II) complex [Cu(II)(phen)(2)](NO(3))(2) (phen = 1,10-phenithroline), and iron complex [Fe(II)(phen)(3)](ClO(4))(2) were fabricated on silicon, quartz and ITO substrates by layer-by-layer self-assembly method. The multilayer films, PSS/Cu(II)(phen)(2)/[(P(2)W(17)/Cu(II)(phen)(2))](n) and PSS/Fe(II)(phen)(3)/[(P(2)W(17)/Fe(II) (phen)(3))](n) were characterized by UV-vis spectra, X-ray photoelectron spectra, cyclic voltammetry (CV), chronoamperometric (CA) and in-situ spectral electrochemical measurements. The interesting feature of the electrochromic film is its adjustable color by reduction of both transition metal complex and polyoxometalate at different potentials. The multilayer films also exhibit high optical contrast, suitable response time and low operation potential due to the presence of mono-lacunary-substituted polyoxometalate and transition metal complex. This is the first example that the color of electrochromic film can be adjustable, which gives valuable information for exploring new electrochromic materials with tunable colors.     

盘状多酸P_5W_(30)/阳离子聚电解质/氧化石墨烯杂化多层膜的电致变色性能

为了提高薄膜[PEI/P_5W_(30)]_(30)的电致变色性能,将具有大的二维尺寸和良好导电性的氧化石墨烯引入该薄膜中。通过层层自组装(LBL)技术构筑了基于盘状多酸K12.5Nal.5[Na P_5W_(30)O_(110)]·15H_2O(P_5W_(30))、氧化石墨烯(GO)的复合薄膜[PEI/P_5W_(30)/PEI/GO]_(30)(PEI:聚乙烯亚胺),并利用UV-Vis光谱对薄膜的组成及增长进行监测;通过原子力显微镜对薄膜的表面形貌进行考察,利用循环伏安法对薄膜电化学氧化还原性质进行研究;薄膜在外加氧化还原电位下呈现出无色/蓝色的可逆变化,电致变色响应时间在10 s以内;此外,薄膜在阶跃电位0.75 V/-0.75 V下循环150次,电致变色性能没有明显减弱,体现了薄膜良好的电致变色可逆性。氧化石墨烯的引入使薄膜[PEI/P_5W_(30)/PEI/GO]_(30)呈现出响应速度快、抗电疲劳强的电致变色性能,将在电致变色器件领域有广阔的应用前景。     

离子液体中聚3-己基噻吩的制备及电致变色性质和器件的研究

以室温离子液体1-丁基-3-甲基咪唑六氟磷酸盐[BMIM]PF₆为溶剂及支持电解质,通过电化学方法制备聚(3-己基噻吩)(PHexT)膜。采用循环伏安法和扫描电子显微镜,对膜的电化学性质及形貌结构进行表征。同时通过紫外可见光谱、计时电流、计时库仑以及计时吸收曲线等方法研究聚合物膜的光谱电化学和电致变色特性,并在此基础上制备PHexT膜的电致变色器件。实验结果表明,在离子液体中制备的PHexT膜光滑致密,掺杂态时为蓝色,脱掺杂时为桔红色,并且具有高的颜色对比度 (40%),较短的响应时间 (2.5 s) 和高的电致变色着色效率 (230cm²/C),该膜制成的固态电致变色器件具有很好的电致变色性能和长的循环寿命。     

Spectroelectrochemical identity of Prussian blue films in various electrolytes: comparison of time-derivative voltabsorptometric responses with conventional cyclic voltammetry

Using Prussian blue (PB) electrodeposited on gold-covered foil as a model system, we have demonstrated the usefulness of the time-derivative measurements of absorbance versus potential (linear potential-scan voltabsorptometry) for spectroelectrochemical characterization of thin electrochromic films. The time-derivative signals were monitored for PB at 680 and 420 nm in potassium, sodium and lithium electrolytes. Information obtained from cyclic voltabsorptometry is equivalent or complementary to that from conventional cyclic voltammetry. In the case of PB films investigated in lithium electrolyte, the voltabsorptometric time-derivative peaks are better defined than the respective voltammetric peaks. The combination of voltabsorptometry with voltammetry enables molar absorptivity and/or film loading to be determined. Also, concentration changes of differently colored mixed-valence redox centers can be monitored as a function of applied potential. Received: 16 January 1997 / Accepted: 11 March 1997     

覆铜板在NaCl溶液中的腐蚀电化学行为

应用线性极化、循环伏安(CV)及电化学阻抗谱(EIS)等电化学方法对覆铜板(CCL)和纯铜的腐蚀电化学行为进行了研究和比较. 结果表明, 覆铜板的耐蚀性弱于纯铜, 其阳极溶解过程与纯铜有所不同; 在较低电位下, CCL 以铜的氯化络合物的形式溶解, CuCl-2的扩散为该过程的控制步骤; 随着电位的升高, 腐蚀产物CuCl在电极表面形成疏松多孔的膜, Cl-在膜中的传输成为溶解过程的控制步骤. 电极表面CuCl 膜的消长过程是产生感抗弧的主要原因.     

Electrode reaction of Pu3+/Pu couple in LiCl-KCl eutectic melts: comparison of the electrode reaction at the surface of liquid Bi with that at a solid Mo electrode.

The electrode reaction of Pu3+/Pu couple at the interface between LiCl-KCl eutectic melt containing PuCl3 and liquid Bi phase was investigated by cyclic voltammetry at 723, 773 and 823 K. For comparison, the system was also studied using a solid Mo electrode in place of the liquid Bi electrode. It was found that the electrode reaction of Pu3+/Pu couple at the Bi electrode was almost reversible. The redox potentials of Pu3+/Pu couple at the liquid Bi electrode in the LiCl-KCl eutectic melt containing 0.87 wt% PuCl3 (0.0014 mole fraction) at 723, 773 and 823 K were observed to be more positive by 0.575, 0.572 and 0.566 V, respectively, than those at the Mo electrode. These differences in potential were thermodynamically analyzed by assuming a lowering of the activity of Pu in Bi phase according to the alloy formation of PuBi2.     

Electrochromism of octaalkoxymethyl-substituted lutetium diphthalocyanine

The electrochromic properties of bis(octaalkoxymethylphthalocyaninato)lutetium films were studied by voltammetry and visible spectrometry. The green molecular films can be oxidized reversibly to form an orange cation and reduced to form a blue anion. The potential of the oxidation step depends on the anion of the aqueous electrolyte in contact with the film.     

Carbon paste electrodes modified with Bi(2)O(3) as sensors for the determination of Cd and Pb

Carbon paste electrodes bulk-modified with Bi(2)O(3)were used for the determination of Cd(II) and Pb(II). The best composition was 1% (wt%) Bi(2)O(3) in the paste. The measurements were made by differential pulse voltammetry in the potential range from -1.2 V to -0.3 V. The peak potential of the reoxidation of Cd is -0.85 V, and of Pb -0.60 V vs. SCE. The lowest concentration that could be determined was 5 microg L(-1) of both metals (preconcentration time 240 s), the relative standard deviation was 3.5%-5.0% (four determinations). The correlation coefficient ( r(2)) of the calibration curves was 0.9966 (for Cd) and 0.9971 (for Pb). The Bi(2)O(3)-modified electrode could be used for the analysis of drinking water, mineral water and urine.