Studies of thermally stimulated current in polypropylene/calcium carbonate/surfactant systems

Thermally stimulated polarization (TSP) and depolarization (TSD) experiments have been performed with two grades of polypropylene and some respective CaCO₃-filled composites containing small amounts of nonionic surfactant (0–2 wt%). The effects of electrode blocking, electrode materials on the thermally stimulated currents, and reproducibility of the measurements have been studied. The effect of water vapor adsorbed from the ambient air on the AC dielectric properties and on the thermally stimulated polarization behavior has been determined.The addition of either CaCO₃ or surfactant to PP decreases the intensity of the _c depolarization current peak in the pre-melting region, while the presence of both components increases the current. Partial discharges are present in poly propylene/CaCO₃ composites under high voltages if neither water vapor nor a coherent surfactant layer is present at the matrix/filler interface.A short literature survey is presented on the TSC studies of polyolefins and their composites, and various mechanisms responsible for the observed changes are discussed, including interfacial polarization, trap redistribution through nucleation, and oriented adsorption.     

Swelling of poly(methacrylic acid) gels and adsorption of L-lysine and its polymer on the gels

Poly (methacrylic acid) gels (PMAA gels) of various degrees of crosslinking were prepared and the dissociation behavior of these gels was examined; the swelling behavior was investigated as a function of the solution pH values. A reentrant phenomenon of swelling was observed and interpreted based on the Flory-Huggins equation and the Donnan equilibrium formula. Moreover, adsorption of L-lysine, oligo(L-lysine)s (Lys-n,n=3, 9, and 19) and poly(L-lysine) onto PMAA gels from aqueous solutions was investigated under different conditions of pH and concentration of adsorbate. The adsorption ratio of L-lysine onto PMAA gel is dependent on both the pH of solution and the degree of crosslinking. In a pH range between 8 and 9, the protonated form of L-lysine is strongly adsorbed on the PMAA gel by electrostatic interactions. Oligomers and polymer of L-lysine are adsorbed in a somewhat different way from the monomeric L-lysine. In addition, the desorption behavior of L-lysine from PMAA gels by a change in pH was also investigated.     

Adsorption of fish oil and poly(vinylbutyral) onto aluminum oxide particles studied by light scattering

The effects of added poly(vinylbutyral) (PVB) and oxidized Menhaden fish oil (O-FO) on dilute suspensions of Al₂O₃ in the azeotropic solvent mixture 73/27 Wt.-% trichloroethylene/ethanol were studied by static (SLS) and dynamic light-scattering (DLS). The DLS correlation function consisted of four terms from: 1) interdiffusion of the two solvents, 2) diffusion of Al₂O₃, 3) diffusion of added O-FO and/or PVB, and 4) an induced velocity of particles through the scattering volume due to laser pressure. The amplitude and relaxation time of all terms could be determined. Addition of PVB to the Al₂O₃ suspension resulted in an increase in particle size corresponding to the adsorption of a monolayer of coils. Addition of O-FO to the Al₂O₃ suspension did not produce a significant increase in particle size, indicating either no adsorption or a compact conformation of O-FO molecules on the Al₂O₃ surface.     

Two-dimensional condensation in camphor-10-sulphonic acid films at the mercury/electrolyte interface

The electrosorption properties of camphor-10-sulphonic acid (CS) in different electrolytes (Na₂SO₄, LiClO₄, KNO₃, KCl, KBr, KJ) were investigated experimentally by ac polarographic measurements at different temperatures. Depending on the type of electrolyte and on the temperature, film condensation was observed.The Frumkin interaction coefficient, determined from the critical degree of coverage, does not depend linearly on the reciprocal temperature as would be the case in correspondence to the temperature dependence of the pit width. This contradiction does not occur if the interaction coefficient is determined from the critical degree of coverage using the lattice gas model. The temperature dependence of the pit width of the differential capacity-potential curves, found in the experiment, can be theoretically described by both these models. The interaction coefficient in the models is inversely proportional to the temperature. Furthermore, the parameters of the standard free energy of adsorption, the interaction energy, the interaction coefficient of the Frumkin isotherm, the adsorption coefficient, and the maximal surface concentration of CS in the film were estimated and compared.     

Characterization of wood fibers modified by phenol-formaldehyde

Wood-fiber phenol-formaldehyde-resin (PFR) modified surfaces, obtained from the adsorption of a PFR/water solution, are investigated as a function of the nature and the amount of PFR adsorbed. Surface are measurements are performed by using krypton adsorption at 77 K. Chemical modification is monitored by the electron spectroscopy for chemical analysis (ESCA) technique and the surface energy by the inverse phase gas chromatography (IPGC) method at infinite dilution. The London dispersive componentγ _S ^L of the surface energy shows a relationship to the concentration of carbon and oxgen at the fiber surface.γ _S ^L increases from 27.5 mN·m⁻¹ for the untreated fiber to 42.5 mN·m⁻¹ for the fibers treated with 20% high molecular-weight-grade phenol-formaldehyde. The surface atomic ratio O/C determined using the ESCA technique exhibits a decrease from 44% for untreated to 31% for treated samples. Surface area also decreases from 2.09 m²/g to 1.50 m²/g. The PFR adsorbed by wood fibers is observed as the dispersive component of surface energy starts to increase, as the surface oxygen concentration decreases, and on the surface area of the wood fiber.     

Effect of inorganic electrolyte concentration on anionic-cationic adsorption films Part 1. Decylpyridinium chloride + sodium octylsulphonate + sodium chloride

The effect of NaCl on simultaneous adsorption of decylpyridinium chloride (R₁₀PyCl) and sodium octylsulphonate (R₈SO₃Na) on the free surface of their aqueous solutions has been examined. The surface excess of each component was determined on the basis of a suitable form of the Gibbs adsorption equation. The ionic strength effect on the adsorption of particular components of mixtures, as well as on the composition of anionic-cationic films adsorbed from equimolar solutions, is small. This is due to little difference in surface activity of surfactants investigated.     

纳米CaCO3的改性、表面结构与流变行为研究

采用铝锆偶联剂和棕榈酸改性纳米CaCO₃ 粉体. 借助 XRD, FTIR, 接触角及流变学等测试方法对纳米CaCO₃ 的表面结构进行表征. XRD 分析表明: 改性纳米 CaCO₃保持原样品完整的体相结构, 为方解石型纳米微晶. FTIR 分析证明: 表面改性剂与纳米 CaCO₃ 表面是以化学键合和物理吸附方式相结合, 粒子表面存在羧基等有机官能团的红外吸收特征. 通过测定苯和水在改性纳米CaCO₃粉末压片上的接触角, 计算了改性纳米 CaCO₃的表面能和极性分量, 并与未改性纳米CaCO₃ 进行比较. 结果表明, 经表面改性, 纳米 CaCO₃ 的表面能和极性分量明显降低, 其在有机溶液中的吸附功增大, 界面张力大大降低; 经棕榈酸改性的纳米 CaCO₃ 表现出较好的亲油疏水性, 而铝锆偶联剂改性的纳米 CaCO₃ 同时具有亲水性和亲油性. 以液体石蜡为溶剂, 研究了表面改性对纳米CaCO₃悬浮液流变行为的影响. 实验发现: 经过表面处理, 纳米 CaCO₃ 粉体悬浮液流变行为发生较大的变化, 稳态剪切黏度大大降低, 表现出较小的动态弹性储能模量和黏性损耗模量, 而损耗因子较大.     

Thermodynamics of adsorption of acetone on active carbon supported metal adsorbents

Adsorption of acetone on active carbon and active carbon supported metals (Ni, Cu, Zn and Cd) have been studied as a function of temperature. Thermodynamic parameters such as G ⁰, H ⁰, and S ⁰ are calculated from virial and Langmuir isotherm expressions. It is observed that active carbon supported metals have more adsorption affinity for acetone as compared to active carbon. Results show that the increase in adsorption affinity for active carbon supported metals is not due to configurational factors affecting the entropy of adsorption, but because of enhanced enthalpy of adsorption. XRD spectra show that active carbon supported metals adsorbents are amorphous and metal residues are present on the surface of active carbon in its reduced form. From adsorption data, isosteric heats and molar entropies of adsorption were calculated as a function of coverages and temperature. The values of isosteric heats of adsorption were found to be higher for active carbon supported metals, which may be due to the chemisorption of adsorbate molecules with metal sites present on the surface of active carbon. The extent of coordination of adsorbate molecules with metal sites is discussed on the basis of the acidic character of metal.     

Conformational changes of polyglutamic acid adsorbed on cationic polystyrene as characterized by microelectrophoresis technique

Polypeptides (polyglutamic acid in sodium form) of three different polymerization degrees have been adsorbed on cationic polystyrene latex. The electrokinetic behavior of the complex PG/PS has been studied by microelectrophoretic mobility. The effect of ionic strength and pH on electrokinetic properties of the complex PG/PS have also been studied. It has been found that the appearance of maximum inu _e -logc curves is related to coverage degree of polystyrene surface and the polymerization degree of polypeptides chains. Likewise, the form of such curves depends markedly on pH. An attempt has been made to explain the data in terms of conformational changes of the adsorbed polypeptides chains.Presented at the NATO Advanced Study Institut on Polymer Colloid, Strasbourg (France), July 1988.     

Gas adsorption by a crystalline silicic acid

Crystalline silicic acids are prepared from alkali layer silicates by exchanging protons for the alkali ions. The acid H₂Si₂₀O₄₁ · xH₂O (parent material K₂Si₂₀O₄₁ · xH₂O) exhibits some outstanding gas adsorption properties which are related to the layer structure and the interlamellar microporosity. The external surface, about 20 m² g^–1, is estimated from nitrogen adsorption data after blocking the micropores. Slit-shaped ultramicropores (with diameters similiar to that of the nitrogen molecule) between the layers are widened to supermicropores near the crystal edges. During an adsorption run the nitrogen molecules penetrate more deeply into the ultramicropores. Nitrogen molecules strongly adsorbed in the ultramicropores are not desorbed at 77 K. Additional amounts of nitrogen are adsorbed by widening of the slit-shaped micropores at the crystal edges when pressure increases. This process proceeds slowly and is reversible.     

Behavior of pure and mixed DPPC liposomes spread or adsorbed at the air-water interface

Liposomes from pure dipalmitoylphosphatidylcholine (DPPC) and mixed DPPC: distearoylphosphatidylcholine (DSPC): soybean lecithin (SL) prepared by the Bangham method with sonication were dispersed into solution or spread at the interface and the kinetics of the surface film formation was studied by measuring and recording the evolution of superficial tension, surface potential, and superficial (¹⁴C labeled) DPPC density.A simple theoretical approach can describe these kinetics by two processes: irreversible diffusion of closed vesicles into or from the bulk phase, and irrevers ible transformation of closed spherical vesicles into destroyed ones which form the surface film. Diffusion controls the phenomenon for small initial amounts of liposomes.Transformation controls the phenomenon for important initial amounts of liposomes. The kinetic constant of the transformation,K, does not depend on the technique used to form the surface film (spreading or adsorption).The equilibrium and rheological properties of surface films formed after liposome spreading are compared to those of monolayers     

Reinforcement effect of MAA on nano‐CaCo3‐filled EPDM vulcanizates and possible mechanism

Methacrylic acid (MAA) was used as in situ surface modifier to improve the interface interaction between nano‐CaCO₃ particle and ethylene–propylene–diene monomer (EPDM) matrix, and hence the mechanical properties of nano‐CaCO₃‐filled EPDM vulcanizates. The results showed that the incorporation of MAA improved the filler–matrix interaction, which was proved by Fourier transformation infrared spectrometer (FTIR), Kraus equation, crosslink density determination, and scanning electron microscope (SEM). The formation of carboxylate and the participation of MAA in the crosslinking of EPDM indicated the strong filler–matrix interaction from the aspect of chemical reaction. The results of Kraus equation showed that the presence of MAA enhanced the reinforcement extent of nano‐CaCO₃ on EPDM vulcanizates. Crosslink density determination proved the formation of the ionic crosslinks in EPDM vulcanizates with the existence of MAA. The filler particles on tensile fracture were embedded in the matrix and could not be observed obviously, indicating that a strong interfacial interaction between the filler and the matrix had been achieved with the incorporation of MAA. Meanwhile, the presence of MAA remarkably increased the modulus and tensile strength of the vulcanizates, without negative effect on the high elongation at break. Furthermore, the ionic bond was thought to be formed only on filler surface because of the absolute deficiency of MAA, which resulted in the possible structure where filler particles were considered as crosslink points. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1226–1236, 2006     

The adsorption process of some acetic acid derivatives at the water/air interface

The adsorption of trifluoro-, trichloro-, tribromo-, and trimethylacetic acid at the water/air interface is discussed on the basis of surface tension measurements. The process of adsorption is described by Henry's and Langmuir's isotherm equations. The obtained results allow calculation of the standard free energy of adsorption of investigated molecules and the contribution to this energy of hydrophobic groups of these molecules.     

Evaluation of hydrophilic-hydrophobic character of zeolites by measurements of their immersional heats in water

Na-type faujasite was modified by SiCl₄ treatment under dealumination-silicon-exchange reaction. Their crystallinities and lattice constants were analyzed by x-ray diffraction, and their surface areas and pore structures were measured by nitrogen adsorption at 77 K. Their hydrophobic characteristics were evaluated by measurements of water adsorption and heats of immersion into weter, and compared with those of ZSM-5 zeolites which were highly silicious at the synthesis process.Adsorption amount ofn-hexane on modified faujasite did not change compared to that on original faujasite, however, the adsorbed amount of water greatly decreased. Heats of immersion in water decreased by the modification and were closely related with the Si/Al ratio of zeolites. Hydrophilic-hydrophobic character is discussed from the viewpoint of water contact angle.     

The influence of nicotinamide on the adsorption equilibrium of aspirin at the aqueous solution-air interface

The coadsorption of aspirin and nicotinamide at the free water surface was investigated. The adsorption properties of investigated compounds are discussed on the basis of Gibb's equation and Temkin's isotherm.The effective dipole moment of aspirin and nicotinamide has been determined by the Helmholtz equation on the basis of surface excess values obtained from surface tension measurements, and surface potential changes. From the effective dipole moments the surface orientation of molecules in the adsorbed film was determined.     

Polyacrylamide Na-kaolinite interactions: Effect of electrolyte concentration on polymer adsorption

The variation in polyacrylamide adsorption on Na-kaolinite as a function of the electrolyte concentration of the clay suspension, was determined under three pH conditions, where the clays display varying charge characteristics. Interpretation of the results is based on two arguments: non-charged polyacrylamide adsorption is restricted to the edge faces of the colloidal platelets and hydrogen bonding between the amide groups of the polymer and the isolated hydroxyl sites of these faces is the mode of surface attachment. At constant pH, when Na-kaolinite bears charged surface groups, the polymer adsorption, which is related to the density of the anchoring sites, parallels the state of ionization of the edge surface. The mechanism by which the salt modifies the adsorption properties of the kaolinite in neutral medium is not established with certainty. Nevertheless, no polymer-clay association occurs if the surface is entirely uncharged. This result is in line with the fact that while hydroxyl groups are engaged in internal hydrogen bonds, they cannot hydrogen-bond to the polyacrylamide. Variations in the clay-polymer affinity are attributed to a modification of the interfacial structure of the adsorbed polymer, associated with changes in the surface density of the anchoring groups.     

The pH dependence of dispersion of TiO2 particles in aqueous surfactant solutions

The pH dependence of dispersion of titanium dioxide (TiO₂) particles has been examined in the presence of surfactant molecules in water. Whereas particles were dispersed in water at acid and alkaline regions rather than at neutral region, the dispersion was enhanced at neutral region in an aqueous sodium dodecyl sulfate (SDS) solution and at acid and alkaline regions in an aqueous dodecyldimethylamine oxide (C₁₂DAO) solution. Considering the pH dependence of zeta potential, the adsorption models of surfactant molecules on a particle were estimated on the basis of the modes of hemimicelle and double-layer compression. While the particles that adsorbed Al³⁺ were remarkably dispersed around pH 6, their dispersion does not largely depend on pH in the addition of SDS, indicating the adsorption of SDS molecules to form double-layer compression in the whole pH region. Dynamic light-scattering measurement and electron microscopic observation suggested that the particles were dispersed in water as small flocs.     

Solutions of alkali soaps and water in fatty acids XIII. Circumstances that regulate the extension of theL 2-phase and the role of the acid-soaps rich in fatty acid for the occurrence of the phase

A basic requirement for that type ofL ₂-phase which exists in the system sodium octanoate-octanoic acid-water is the formation of acid-soaps. In order for the phase to be formed at all, the temperature must lie above the melting point of the fatty acid so that a reaction in non-aqueous milieu between neutral soap and fatty acid is possible. In order to obtain the characteristic shape and complete extension of the phase in direction of high water content the temperature must be so high that also the hydrated acid-soaps occur in fluid state. On the other hand the temperature cannot be so high that the acid-soaps become unstable.At temperatures at which the phase has obtained its full extension those circumstances differs which in different regions regulate the location of the phase borders; they depend on the composition of the acid soaps and on their amounts. In that part of the phase where the molar ratio between octanoic acid and sodium octanoate lies between 2 and 3 and where one has a continuous transition from reversed to normal structure only the two acid octanoates 1 NaC₈ 2 HC₈ x H₂O and 1 NaC₈ 3 HC₈ x H₂O occur and both are at 20 °C in fluid state.At water contents from about 22 % to 40 % the hydrate-water molecules belonging to the first mentioned soap are capable of contributing actively to the formation of large aggregates of acid-soap, a process which however is counteracted by the inmixing of the latter acid-soap. This mixture of the two acid-soaps decides in this region where the border of the phase will lie in direction towards an increased content of sodium octanoate; the result is that in spite of the fact that the hydration is increased, the border is only slowly displaced towards a higher content of fatty acid. As soon as the hydration of the acid octanoates has been completed and the additional water occurs as unbound bulkwater, the location of the phase boundary will no longer be influenced by the water content — now it will be the amphiphilic composition of the acid-soaps that determines the location of the border and it remains at the molar ratio 2.5 between octanoic acid and sodium octanoate at water contents from about 40% and up to 82%.In the direction of decreasing content of neutral sodium octanoate and increased content of water theL ₂-phase both at the highest content of fatty acid and the highest contents of water will be in equilibrium with the water-richL ₁-phase; in the first mentioned region with theL ₁-phase below the lac where at the border it is saturated with octanoic acid and in the latter region with theL ₁-phase just above the lac, where the dilute sodium octanoate solution contains dissolved 1 NaC₈ 1HC₈ x H₂O. In the large central part of theL ₂-phase, from about 20 % to about 86 % of water, the location of the border is dominated by the acid octanoate 1 NaC₈ 3 HC₈ x H₂O and that makes an equilibrium with theL ₁-phase impossible; instead one has an equilibrium via a two-phase zone between the amphiphile-rich region of theL ₂-phase and its water-rich region. In the first region the location of the border is regulated by the decreasing capability of the hydrated acid octanoate 1 NaC₈ 3 HC₈ x H₂O to dissolve octanoic acid; in the latter it is regulated by the fact that 1 NaC₈ 3 HC₈ x H₂O is the most fatty acid-rich acid-soap that is formed and that the octanoic acid is very little soluble in water and in the aqueous solution of this acidsoap.The middle part of theL ₂-phase, especially the region between about 55 % and 82 % of water, constitutes a direct continuation of the liquid crystalline lamellarD-phase. The liquid crystalline character of theD-phase is lost at the transition, but the lamellar organization is retained. That the molecules at least up to a water content of about 40 % are of the original reversed type and have an elongated shape with a central part of hydrated polar groups, from which core the hydrocarbon chains extend in two opposite directions, is the reason to that they, at crowding, form transient layer-like agglomerates of tightly packed more or less parallel molecules; this facilitates the transformation to coherent double amphiphilic layers, in which all molecules lie with the hydrated polar groups outwards toward coherent domains of bulk-water, without another liquid phase occurs.     

Adsorption of quaternary ammonium chlorides with various hydrocarbon chain lengths to glass

Contact angles, measured with various liquids, have been employed to calculate the surface free energies of glass after adsorption of quaternary ammonium chlorides with a variable hydrocarbon chain length 8n16. The thickness of the adsorbed layers has been determined ellipsometrically. A clear relation is observed between the measured parameters and the hydrocarbon chain lengthn, if only the extremesn=8 andn=16 are considered. Surface free energies decrease from 138 erg.cm^–2 for clean glass to 101 and 64 erg.cm^–2 forn=8 andn=16, respectively, at the highest concentration tested (7.5 mM). The adsorbed layer thickness of C₈ amounts to approximately 50 % of the thickness observed for C₁₆. No clear relation between the measured parameters is observed for the intermediate hydrocarbon chain lengths, which presumably reflects the many configurations possible in these adsorbed layers. It is envisaged that adsorption of C₈ as well as C₁₆ is restricted to a monolayer, which is completed at approximately 2 mM. In the case of C₈ electrostatic repulsion between the polar headgroups will inhibit further adsorption, whereas in the case of C₁₆ the van der Waals attraction from the adsorbed layer and the glass will probably not be sufficient to stimulate further adsorption.     

Polymer adsorption on fine particles; the effects of particle size and its stability

The effects of particle size on polyacrylamide (PAAm,M _w =59×10⁴, 500×10⁴) adsorption were investigated using a series of well-characterized hematite (-Fe₂O₃) dispersions. The -Fe₂O₃ particles with highly monodisperse and nearly spherical shape ranged in radius from 23 nm to 300 nm. the maximum amount of PAAm adsorption (M _m ) in each system, showed a steady increase with decreasing particle radius and was influenced strongly by particle concentrations in the medium. Furthermore, it was realized that the diameter of -Fe₂O₃ particles after treatment with PAAm under different particle concentrations decreased with increasing particle concentration. The relation between particle concentration in the medium and particle size after treatment was also influenced by the medium pH, i.e., at the medium pH close to the isoelectric point of -Fe₂O₃ particles (pH^o=9.2), the particle size after treatment increased with increasing particle concentration. All these results suggest that in the system of ultra-fine particles, the mixing process between particle-particle and polymerparticle will play an important role on the conformation of adsorbed polymer layer.