Method development for fingerprinting of biodiesel blends by solid-phase extraction and gas chromatography-mass spectrometry

A method based on the combination of solid-phase extraction (SPE) with gas chromatography-mass spectrometry (GC/MS) for detailed chemical fingerprinting of biodiesel/petrodiesel blends was developed in the present study. Forensic identification, commonly referred to as chemical fingerprinting, is based on the relative distributions of individual aliphatic hydrocarbons, aromatic hydrocarbons, fatty acid alkyl esters, and free sterols. Fractionation of fuel samples is optimized for the separation of fatty acid esters and free sterols from petroleum hydrocarbons into four fractions: aliphatic, aromatic, fatty acid ester, and polar components. The final recoveries of aliphatic and aromatic hydrocarbons were determined to be in the range of 65-103%, 73-105% for FAMEs, and 78-103% for free sterols in the polar fraction. Excellent separation with negligible crossover of components with different polarities between fractions was observed. Quantitative analysis of blend levels and individual chemical distribution were achieved. The method has great potential for the identification of biodiesel in diesel fuel blends and could form the basis of a method for characterization of biodiesel-contaminated environmental samples.     

Determination of total biodiesel fatty acid methyl, ethyl esters, and hydrocarbon types in diesel fuels by supercritical fluid chromatography-flame ionization detection

A method for determining total biodiesel methyl and ethyl ester content in diesel fuels by supercritical fluid chromatography-flame ionization detection (SFC-FID) is developed. A silica column typically used for determining aromatics in conventional diesel fuels by ASTM D5186 is back-flushed after separation of the hydrocarbons to allow elution of the various esters as a single "total biodiesel" distinct peak. The modification concurrently allows the determination of total aromatic hydrocarbons and their distribution as mono- and polynuclear compounds, as described in the current version of D5186. The instrument response is linear from 1.0% to 50% biodiesel esters with a signal-to-noise ratio of 25 at the 0.1% level. The short-term relative standard is 0.8%. Normalized percent quantitation using a hydrocarbon response factor of 1.00 and an ester response factor of 1.19 provide an average percentage error of 1.8% when measuring actual biodiesel/hydrocarbon fuel blends. The ester response factor is the average of the response factors of 10 pure ester compounds. These responses are calculated from respective solutions of each ester and the four compounds, hexadecane, toluene, tetralin, and naphthalene, as used for the D5186 response factor mixture.     

Quantification of trace fatty acid methyl esters in diesel fuel by using multidimensional gas chromatography with electron and chemical ionization mass spectrometry

Measurement of contamination of marine and naval diesel fuels (arising from product mixing or adulteration) with biodiesel or fatty acid methyl esters can be problematic, especially at very low levels. A suitable solution for this task for trace amounts of individual fatty acid methyl esters with resolution and quantification can be achieved by using a multidimensional gas chromatographic approach with electron and chemical ionization mass spectrometric detection. A unique column set comprising a 100 m methyl‐siloxane nonpolar first dimension column and high‐temperature ionic liquid column in the second dimension enabled identification of individual fatty acid methyl esters at below the lowest concentrations required to be reported in a diesel fuel matrix. Detection limits for individual fatty acid methyl esters compounds ranged from 0.5 to 5.0 mg/L, with excellent linearity up to 5000 mg/L and repeatability of the method from 1.3 to 3.2%. The method was applied to the analysis of diesel fuel samples with suspected biodiesel contamination. Contamination at 568 mg/L was calculated for an unknown sample and interpretation of the results permitted the determination of a likely source of the contamination.     

Forensic identification of spilled biodiesel and its blends with petroleum oil based on fingerprinting information

A case study is presented for the forensic identification of several spilled biodiesels and its blends with petroleum oil using integrated forensic oil fingerprinting techniques. The integrated fingerprinting techniques combined SPE with GC/MS for obtaining individual petroleum hydrocarbons (aliphatic hydrocarbons, polyaromatic hydrocarbons and their alkylated derivatives and biomarkers), and biodiesel hydrocarbons (fatty acid methyl esters, free fatty acids, glycerol, monoacylglycerides, and free sterols). HPLC equipped with evaporative scattering laser detector was also used for identifying the compounds that conventional GC/MS could not finish. The three environmental samples (E1, E2, and E3) and one suspected source sample (S2) were dominant with vegetable oil with high acid values and low concentration of fatty acid methyl ester. The suspected source sample S2 was responsible for the three spilled samples although E1 was slightly contaminated by petroleum oil with light hydrocarbons. The suspected source sample S1 exhibited with the high content of glycerol, low content of glycerides, and high polarity, indicating its difference from the other samples. These samples may be the separated byproducts in producing biodiesel. Canola oil source is the most possible feedstock for the three environmental samples and the suspected source sample S2.     

Procedure for and results of simultaneous determination of aromatic hydrocarbons and fatty acid methyl esters in diesel fuels by high performance liquid chromatography

The content of aromatic hydrocarbons in diesel fuels is regulated by appropriate standards, and a further reduction in the allowed concentration of these hazardous substances in these fuels is expected. The content of aromatic hydrocarbons in diesel fuels is most often determined using standard methods EN-12916 or ASTM D-6591. The content of polycyclic aromatic hydrocarbons (PAHs) is determined from a single peak obtained using normal phase high-performance liquid chromatography (NP-HPLC), a column of the NH2 type, n-heptane as the eluent, refractive index detector (RID) and backflushing of the eluent. However, the methods mentioned above cannot be applied when the fuel contains fatty acid methyl esters (FAME), which lately has become more common. The content of FAME in diesel oils is determined using mid-IR spectrophotometry based on the absorption of carbonyl group. However, no standard procedure for the determination of classes of aromatic hydrocarbons in diesel fuels containing FAME is yet available. The present work describes such a modification of methods EN-12916/ASTM D-6591 that provides a simultaneous determination of individual groups of aromatic hydrocarbons, total content of polycyclic aromatic hydrocarbons and the FAME content in diesel fuels. The refractive index detector (RID) and n-heptane as the mobile phase are still used, but backflushing of the eluent is applied after the elution of all polycyclic aromatic hydrocarbons. Additionally, ultraviolet diode array detection is used for the exact determination of low contents of polycyclic aromatic hydrocarbons and to confirm the presence of FAME in the analyzed fuel.     

Characterization of biodiesel and biodiesel blends using comprehensive two-dimensional gas chromatography

In this work the development of a comprehensive 2-D GC flame ionization detection (GC x GC FID) method for biodiesel fuels is reported. This method is used for the analysis of fatty acid methyl esters (FAMEs) in both biodiesel (B100) and biodiesel blend (B5) samples. The separation of FAME was based on component boiling point in the first dimension and polarity in the second dimension by using a BPX5/BP20 column set to provide a measure of 'orthogonality' in the 2-D space. Here the columns are coupled with a cryogenic modulator operating in a novel temperature programmed mode (T(M)) whereby the cryotrap is progressively incremented in temperature as the oven temperature is increased. The final method employs eight cryotrap temperature settings. The developed GC x GC method is able to successfully characterize and identify both B100 and B5 FAME components, which are produced from a variety of vegetable oils, animal fats and waste cooking oils, with high precision. The method is capable of analysing FAME with carbon numbers C4-C24, and is particularly suitable to characterize various types of biodiesel, making it possible to differentiate the origin and type of FAME used in the biodiesel samples.     

Rapeseed oil methyl ester pyrolysis: on-line product analysis using comprehensive two-dimensional gas chromatography

Thermochemical conversion processes play a crucial role in all routes from fossil and renewable resources to base chemicals, fuels and energy. Hence, a fundamental understanding of these chemical processes can help to resolve the upcoming challenges of our society. A bench scale pyrolysis set-up has been used to study the thermochemical conversion of rapeseed oil methyl ester (RME), i.e. a mixture of fatty acid methyl esters. A GC×GC, equipped with both a flame ionization detector (FID) and a time-of-flight mass spectrometer (TOF-MS), allows quantitative and qualitative characterization of the reactor feed and product. Analysis of the latter is accomplished using a dedicated high temperature on-line sampling system. Temperature programmed analysis, starting at -40°C, permits effluent characterization from methane up to lignoceric acid methyl ester (C(25)H(50)O(2)), in a single run of the GC×GC. The latter combines a 100% dimethylpolysiloxane primary column with a 50% phenyl polysilphenylene-siloxane secondary column. Modulation is started when the oven temperature reaches 40°C, thus dividing the chromatogram in a conventional 1D and a comprehensive 2D part. The proposed quantification approach allows to combine the quantitative GC×GC analysis with 2 other on-line 1D GC analyses, resulting in a complete and detailed product composition including the measurement of CO, CO(2), formaldehyde and water. The GC×GC reveals that the product stream contains a huge variety of valuable products, such as linear alpha olefins, unsaturated esters and aromatics, that could not have been identified and quantified accurately with conventional 1D GC because of peak overlap.     

Soybean biodiesel methyl esters,free glycerin and acid number quantification by 1H nuclear magnetic resonance spectroscopy

Production of alternative fuels, such as biodiesel, from transesterification of vegetable oil driven by heterogeneous catalysts is a promising alternative to fossil diesel. However, achieving a successful substitution for a new renewable fuel depends on several quality parameters. ¹H NMR spectroscopy was used to determine the amount of methyl esters, free glycerin and acid number in the transesterification of soybean oil with methanol in the presence of hydrotalcite‐type catalyst to produce biodiesel. Reaction parameters, such as temperature and time, were used to evaluate soybean oil methyl esters rate conversion. Temperatures of 100 to 180 °C and times of 20 to 240 min were tested on a 1 : 12 molar ratio soybean oil/methanol reaction. At 180 °C/240 min conditions, a rate of 94.5 wt% of methyl esters was obtained, where free glycerin and free fatty acids were not detected. Copyright © 2012 John Wiley & Sons, Ltd.     

Emission profile of rapeseed methyl ester and its blend in a diesel engine

Fatty acid methyl esters, also known as biodiesel, have been shown to have a great deal of potential as petro-diesel substitutes. Biodiesel comprise a renewable alternative energy source, the development of which would clearly reduce global dependence on petroleum and would also help to reduce air pollution. This paper analyzes the fuel properties of rapeseed biodiesel and its blend with petro-diesel, as well as the emission profiles of a diesel engine on these fuels. Fuels performance studies were conducted in order to acquire comparative data regarding specific fuel consumption and exhaust emissions, including levels of carbon monoxide (CO), carbon dioxide (CO₂), smoke density, and NO_x, in an effort to assess the performance of these biodiesel and blend. The fuel consumption amount of oil operations at high loads was similar or greater than that observed during petro-diesel operation. The use of biodiesel is associated with lower smoke density than would be seen with petro-diesel. However, biodiesel and its blend increased the emission of CO, CO₂, and nitrogen oxides, to a greater degree than was seen with petro-diesel. The above results indicate that rapeseed biodiesel can be partially substituted for petro-diesel under most operating conditions, regarding both performance parameters and exhaust, without any modifications having to be made to the engine.     

Critical review on analytical methods for biodiesel characterization

Biodiesel is an alternative fuel composed of mono-alkyl esters and obtained mainly from the base-catalyzed transesterification reaction of oils or fats. Its use (pure or blended) does not demand any modification in the diesel engine and in the existing fuel distribution and storage infrastructure. Moreover, biodiesel has a high energetic yield, fixes the solar energy and contains insignificant amounts of sulphur. Therefore, biodiesel is currently the best substitute for fossil diesel fuel.Besides mono-alkyl esters, glycerol (main co-product), alcohol, catalyst, free fatty acids, tri-, di- and monoglycerides compose the final mixture of biodiesel production process. These and other kinds of contaminants can lead to severe operational and environmental problems. Therefore, the quality control of biodiesel is greatly significant to the success of its commercialization and market acceptance. Some important issues on the biodiesel quality control involve the monitoring of transesterification reaction, the quantification of mono-alkyl esters and free- and bonded glycerol as well as determination of residual catalysts and alcohol. Moreover, the determination of blend levels is another key aspect of biodiesel analyses. Chromatography and spectroscopy are the analytical methods most used for the biodiesel characterization, but procedures based on physical properties are also available.Previously, a review on analytical methods used to evaluate biodiesel quality was written by Knothe. Due to the importance of this field, we made an update of Knothes’ review. Therefore, in this paper, we will describe new developments in biodiesel analyses and some references showed in Knothes’ paper. Specially, we will describe analytical methods used for quantification of glycerol, mono-, di-, triglycerides, methanol, water, Na, K, P, and steroids in biodiesel or along the transesterification reaction. Also, the determination of biodiesel content in blends and some physicochemical parameters are discussed. At the end, we will assess the available techniques and point out some improvements on analytical methods for biodiesel characterization.     

Electrochemical Determination of Organic Compounds in Automotive Fuels

This article critically reviews the electroanalytical methods devoted for the determination of organic compounds in automotive fuels that can range from contaminants to additives typically introduced into liquid biofuels and liquid fossil fuels. Contaminants such as aldehydes and ketones in bioethanol, free fatty acids and glycerol in biodiesel, and sulfur and nitrogen organic compounds in gasoline and diesel fuel, and additives such as colour markers and antioxidants added to fuels were determined by electroanalytical methods. Special focus is given to electrodes, electrochemical techniques, and sample preparation strategies. Future directions of research on electroanalysis of liquid fuels are presented.     

Multivariate near infrared spectroscopy models for predicting the methyl esters content in biodiesel

Biodiesel is the main alternative to fossil diesel. The key advantages of its use are the fact that it is a non-toxic renewable resource, which leads to lower emissions of polluting gases. European governments are targeting the incorporation of 20% of biofuels in the general fuels until 2020.Chemically, biodiesel is a mixture of fatty acid methyl esters, derived from vegetable oils or animal fats, which is usually produced by a transesterification reaction, where the oils/fats react with an alcohol, in the presence of a catalyst. The European Standard (EN 14214) establishes 25 parameters that have to be analysed to certify biodiesel quality and the analytical methods that should be used to determine those properties.This work reports the use of near infrared (NIR) spectroscopy to determine the esters content in biodiesel as well as the content in linolenic acid methyl esters (C18:3) in industrial and laboratory-scale biodiesel samples. Furthermore, calibration models for myristic (C14:0), palmitic (C16:0), stearic (C18:0), oleic (C18:1), linoleic (C18:2) acid methyl esters were also obtained. Principal component analysis was used for the qualitative analysis of the spectra, while partial least squares regression was used to develop the calibration models between analytical and spectral data. The results confirm that NIR spectroscopy, in combination with multivariate calibration, is a promising technique to assess the biodiesel quality control in both laboratory-scale and industrial scale samples.     

Multivariate near infrared spectroscopy models for predicting the iodine value, CFPP, kinematic viscosity at 40 degrees C and density at 15 degrees C of biodiesel

Biodiesel is one of the main alternatives to fossil diesel. It is a non-toxic renewable resource, which leads to lower emissions of polluting gases. In fact, European governments are targeting the incorporation of 20% of biofuels in the fossil fuels until 2020.Chemically, biodiesel is a mixture of fatty acid methyl esters, derived from vegetable oils or animal fats, which is usually produced by a transesterification reaction, where the oils or fats react with an alcohol, in the presence of a catalyst. The European Standard (EN 14214) establishes 25 parameters that have to be analysed to certify biodiesel quality and the analytical methods that should be used to determine those properties.This work reports the use of near infrared (NIR) spectroscopy to determine some important biodiesel properties: the iodine value, the cold filter plugging point, the kinematic viscosity at 40 °C and the density at 15 °C. Principal component analysis was used to perform a qualitative analysis of the spectra and partial least squares regression to develop the calibration models between analytical and spectral data. The results support that NIR spectroscopy, in combination with multivariate calibration, is a promising technique applied to biodiesel quality control, in both laboratory and industrial-scale samples.     

Decomposition and hydrocarbon growth processes for esters in non-premixed flames

Biomass fuels are a promising renewable energy source, and so, the mechanisms that may produce toxic oxygenated byproducts and aromatic hydrocarbons from oxygenated hydrocarbons are of interest. Esters have the form R-(C=O)-O-R' and are components of biodiesel fuels. The five specific esters studied here are isomers of C5H10O2. The experiments were performed in atmospheric pressure coflowing methane/air non-premixed flames. A series of flames were generated by separately doping the fuel mixture with 5,000 ppm of each ester. This concentration is sufficiently large to produce measurable changes in intermediate hydrocarbon concentrations, yet small enough to not disturb the overall flame structure. Since the overall structure is not perturbed, the measured changes in the intermediate hydrocarbons can be directly attributed to the reactions of the esters. Analysis of these changes reveals that unimolecular six-centered dissociation is the primary decomposition pathway for the three esters with molecular arrangements capable of undergoing that mechanism. The remaining two esters exhibited decomposition rates and products that are consistent with simple fission as the dominant decomposition mechanism, though we do not exclude other pathways from playing a significant role in their decomposition. All of the esters produce aromatic hydrocarbons at higher rates than the undoped fuel, and the molecular arrangement of the ester isomers plays a role in the degree of aromatic formation. Isomer variations also influence the type and quantity of toxic oxygenates that are produced in the flames.     

Determination of acylglycerols in vegetable oil methyl esters by on-line normal phase LC-GC

An on-line LC-GC method for the analysis of mono-, di-, and triacylglycerols in vegetable oil methyl esters has been developed. The concentrations of these components have turned out to be key parameters for the quality of diesel fuel substitutes. Separation of all classes of acylglycerols from the fatty acid methyl ester matrix is achieved by LC after acetylation of the hydroxyl groups. The acylglycerol fraction is transferred on-line to GC, using the loop-type interface and concurrent eluent evaporation. Quantification of mono-, di-, and triacylglycerols is performed by combining external calibration with internal standardization. Both recovery of the procedure and reproducibility of the quantitative results are evaluated.     

气相色谱法测定生物柴油中脂肪酸甲酯含量

生物柴油是利用动植物油脂等可再生资源通过酯交换技术制造的可以替代石化柴油的新型清洁安全燃料[1-3]它的主要成分是脂肪酸甲酯。由于不同油脂原料所生产的生物柴油的脂肪酸甲脂组成不同因而测定时所需的气相色谱条件与方法也不尽相同[4-6]。本文采用HP-innowax毛细管色谱柱,     

Experimental comparison of performance and emission characteristics of 4-stroke CI engine operated with Roselle and Jatropha biodiesel blends

The environmental degradation, combined with the continuous depletion of the world's fossil fuel reserves, has forced the search for alternative fuels. This study was performed to investigate the performance of novel biodiesels in the CI engine. The experiments were performed at three different compressions ratios (16:1, 17:1, 18:1) and four loading conditions (25%, 50%, 75%, 100%). Different types of fuels such as jatropha biodiesel (JB), roselle biodiesel (RB), and ternary biodiesel (TB) were prepared and analyzed. The thermal performance of different fuels was analyzed in terms of brake thermal efficiency (BTE), brake specific fuel consumption (BSFC), and exhaust gas temperature (EGT). The emission characteristics such as CO₂ emission, NO_x emission, and smoke emission were analyzed for all types of fuels. The results of these fuels in the engine were compared with mineral diesel (MD). The BTE was increased with increasing compression ratios and loads for all types of fuels. The BSFC was increased with increasing compression ratios but decreased with increasing loads. The increase in emission of NO_x was observed at higher compression ratios and loads. However, the CO₂ emission was decreased at higher loads and lower compression ratio. The performance curves achieved with a 20% jatropha biodiesel blend showed results that were approximate to those obtained with pure MD. The comparative analysis between different fuels showed that JB exhibit higher thermal performance as compared to other biodiesels. Therefore, JB can be a better alternative to conventional fuel.     

Biodiesel Production from Vegetable Oils and Animal Fat over Solid Acid Double-Metal Cyanide Catalysts

Biodiesel comprises of fatty acid alkyl esters prepared from vegetable oils or animal fat by esterification/transesterification with short-chain alcohols (methanol or ethanol, for example). It is a biodegradable renewable fuel. Its production is growing exponentially due to greater concerns about environmental protection and depletion of fossil fuel resources. Further, its production from non-edible oils and animal fat is more desirable than from edible oils due to lower cost of non-edible feedstocks and elimination of food verses fuel issues. Solid acid catalysts are ideal for conversion of such low-grade oils to biodiesel. Biodiesel from non-edible oils can be produced by two methods: (1) simultaneous esterification of fatty acids and transesterification of fatty acid glycerides and (2) hydrolysis of glycerides followed by esterification. This account reports the catalytic performance of solid, Fe–Zn double-metal cyanide (DMC) complexes and other acid catalysts in these transformations for biodiesel production. The factors influencing the catalytic performance of the solid acid catalysts in biodiesel production are discussed.     

Development and application of an analytical method for the determination of storage lipids, fatty acids and fatty alcohols in Calanus finmarchicus

A method was developed for the determination of the major storage lipids, wax ester and triglycerides, in the copepod Calanus finmarchicus. A variation of the Folch method was used to extract the lipid. The method was scaled down to enable the extraction of either pooled (-1 mg) or individual (approximately 200 microg) copepods. The major lipid classes were identified using TLC and quantified using HPLC coupled with evaporative light scattering detection. Analysis of laboratory reference materials indicated that this method underestimated the minor triglyceride component, but gave a good estimate of the major wax ester component. The fatty acid and fatty alcohol composition of the C. finmarchicus were determined following trans-esterification of the lipid extract in methanol. Fatty acids and fatty alcohols were initially identified by comparison with authentic standard and by mass spectroscopy. Using GC with flame ionisation detection the normalised area percentage of the fatty alcohols and fatty acid methyl esters was determined simultaneously in one run for either pooled or individual copepod samples. These methods were applied to C. finmarchicus collected from the Irminger Sea, North Atlantic in 2001 and 2002.     

Analysis of biodiesel/petroleum diesel blends with comprehensive two-dimensional gas chromatography

Comprehensive two-dimensional gas chromatography (GCxGC) is used to analyze petroleum diesel, biodiesel, and biodiesel/petroleum diesel blends. The GCxGC instrument is assembled from a conventional gas chromatograph fitted with a simple, in-line fluidic modulator. A 5% phenyl polydimethylsiloxane primary column is coupled to a polyethylene glycol secondary column. This column combination generates chromatograms where the fatty acid methyl esters (FAMEs) found in biodiesel occupy a region that is also populated by numerous cyclic alkanes and monoaromatics found in petroleum. Fortunately, the intensities of the petroleum hydrocarbon peaks are far lower than the intensities of the FAME peaks, even for blends with low biodiesel content. This allows the FAMEs to be accurately quantitated by direct integration. The method is calibrated by analyzing standard mixtures of soybean biodiesel in petroleum diesel with concentrations ranging from 1 to 20% v/v. The resulting calibration curve displays excellent linearity. This curve is used to determine the concentration of a B20 biodiesel/petroleum diesel blend obtained from a local retailer. Excellent precision and accuracy are obtained.