Analysis and optimization of an InGaAsP/InP waveguide variable optical attenuator

An InGaAsP/InP waveguide variable optical attenuator (VOA) is proposed in this paper. The device consists of straight input and output waveguides and an S-bend waveguide. An electrode is deposited on a portion of the waveguide to form an active region so that its refractive index can be modified by a current injection, resulting in the variation of the transmitted optical power. The beam propagation method is employed in the numerical simulation and the device structure is optimized using a genetic algorithm. The optimized VOA has a low excess loss (<1 dB) and a large dynamic range of about 40 dB.     

Polymer waveguide thermo-optic switches with −70 dB optical crosstalk

To reduce the crosstalk of the polymer waveguide optical switches, waveguide attenuators are integrated with the switch on the same substrate. The switch and attenuator shares a single connected electrode which is controlled by a single current source. Due to the simple structure of the integrated attenuator, the device length is reduced to 10 mm so as to provide low insertion loss of 0.8 and 1.1 dB for 1300 and 1550 nm, respectively. Further radiation of the remained optical signal on the switch-off branch is induced by the integrated attenuator so that the switching crosstalk is reduced to −70 dB with an applied electrical power of 200 mW. The low crosstalk is maintained for the environmental temperature range of −10 to 55 °C.     

Modeling of electrically actuated elastomer structures for electro-optical modulation

A transparent elastomer layer sandwiched between two metal electrodes deforms upon voltage application due to electrostatic forces. This structure can be used as tunable waveguide. We investigate structures of a polydimethylsiloxane (PDMS) layer with 1–30 μm thickness and 40 nm gold electrodes. For extended electrodes the effect size may be calculated analytically as a function of the Poisson ratio. A fully coupled finite-element method (FEM) is used for calculation of the position-dependent deformation in case of structured electrodes. Different geometries are compared concerning actuation effect size and homogeneity. Structuring of the top electrode results in high effect magnitude, but non-uniform deformation concentrated at the electrode edges. Structured bottom electrodes provide good compromise between effect size and homogeneity for electrode widths of 2.75 times the elastomer thickness.     

Polymeric PLC-type thermo-optic optical attenuator fabricated by UV imprint technique

A planar lightwave circuit-type polymer thermo-optic optical attenuator was fabricated via a UV imprint technique. In order to reduce the step for filling of cores and minimize the detrimental residual slab waveguide, convex ridge-type micro cores for guidance of light were defined with an accuracy of ±0.5 μm on the under-clad by a single step of imprinting. The voltage-controlled polymer optical attenuator showed 30-dB attenuation with 80-mW electrical input power at a wavelength of 1.55 μm. The rise and fall times are less than 5 ms. It displays about 0.2- and 1-dB polarization dependence at 0- and 10-dB attenuations, respectively.     

New design for a variable optical attenuator based on a bent channel waveguide

We present a new method for bend loss control in a curved channel optical waveguide and employ it in a novel design of a thermo-optic variable optical attenuator. We show that the introduced asymmetric refractive index profile of the waveguide structure, combined with the optimal placement of the heating electrodes, leads to a significant increase of the dynamic range of the attenuator. PACS 42.82.Et; 42.70.Jk; 42.79.Ta     

The thermo-optical variable optical attenuator based on SOI

A thermo-optical variable optical attenuator was studied based on silicon on insulator (SOI) substrate waveguide. It is composed by the single-mode waveguide, taper waveguide, multi-mode waveguide, and inclined electrode. By adjusting the applied voltage on the inclined electrode it can achieve continuously variable attenuation of the output light. The results we studied show that when the applied voltage is about 4.7 V (the corresponding power is 233 mW), the variation of the waveguide's core temperature is about 33 °C, the refractive index changes more than 5.0 × 10⁻³ and the attenuation will reach 35 dB, and the response time is only 35 μs.     

High-speed electrooptical VOA integrated in silicon-on-insulator

In this paper, we present simulation results of an electrooptical variable optical attenuator (VOA) integrated in silicon-on-insulator waveguide. The device is functionally based on free carriers absorption to achieve attenuation. Beam propagation method (BPM) and two-dimensional semiconductor device simulation tool PISCES-II were used to analyze the dc and transient characteristics of the device. The device has a response time (including rise time and fall time) less than 200 ns, much faster than the thermooptic and micro-electromechanical systems (MEMSs) based VOAs.     

S弯曲聚合物热光型可变衰减器的特性

提出一种热光聚合物可变光衰减器(VOA)的设计分析,利用S弯曲的波导提高衰减效率,BPM法模拟中验证其衰减动态范围可达60 dB,实现60 dB的衰减计算功耗为60 mW,附加弯曲损耗小于0.3 dB.并且具有很好的极化独立性,串扰低,尺寸小,易于集成.     

Polymeric arrayed waveguide grating using imprint method incorporating a flexible PDMS stamp

A polymeric arrayed waveguide grating (AWG) has been proposed and demonstrated by employing the nanoimprint method. A flexible PDMS (polydimethylsiloxane) stamp with the device patterns engraved was developed from a rigid master mold made of quartz glass, featuring uniform precision contact with and easy separation from polymer films. The device was fabricated by replicating the pattern on the stamp in a core polymer layer, with no etching process involved. For our device, the number of the output channels is eight and the center wavelength of each output channel is positioned from 1543.7 nm to 1548.3 nm with the spacing of 0.8 nm. The achieved channel crosstalk was about 10 dB and the 3 dB bandwidth approximately 0.8 nm.     

Lossy double negative guiding layer optical sensors

We proposed a three-layer waveguide as an optical sensor for homogeneous sensing applications. A guiding layer of the proposed structure is considered as lossy left-handed material (LHM) with simultaneously the complex negative electric permittivity ɛ and the complex negative magnetic permeability μ. We also assume a cladding layer to have an intensity-dependent refractive index. Sensitivity of the proposed optical waveguide sensor is derived and its dependence on different parameters of a waveguide is studied.     

Theoretical model of a planar waveguide refractive index sensor assisted by a corrugated long period metal grating

A theoretical model of a novel planar integrated refractive index sensor based on surface plasmon-polariton (SPP) excitation with a corrugated metal long period grating (LPG) is presented and comprehensively investigated. The main principle of the operation this device is based on co-directional energy transfer by means of a corrugated metal LPG between a p-polarized guided mode propagating in a waveguide layer and the SPP propagating a metal layer separated from the waveguide layer by a buffer. The corrugated LPG is engraved in the metal layer in contact with the sensed medium. The power transmitted through the LPG in the guided mode serves as an input signal for an interrogation unit. This device is free from any moving parts and can be simply integrated into any planar waveguide system. Our sensor simulations are based on the local-normal-mode transfer matrix method and performed in telecom wavelength range.     

Microwave System for BEPCⅡ-Linac

Specifications of microwave system for BEPCⅡ-Linac were enhanced by a wide margin in comparison with those of the microwave system for BEPC-Linac. For this reason many RF components must be developed and improved. This paper introduces the developments of SLED detuning system, accelerating section, high power waveguide valve, high power dummy-load, and medium & high power waveguide attenuator/phase shifters. High power operation of the microwave system has been carried out.     

Experimental analysis of metal coated dielectric waveguides

This paper concerns the experimental characteristics of metal coated dielectric waveguides with a rectangular surface corrugation. Waveguide are designed to operate at a second Bragg frequency of 90 GHz. The period, height and the duty cycle of a rectangular grating were calculated using the chosen frequency. A metallic layer of aluminum is sputtered on one side of the slab waveguide. The purpose of the metallic layer is to simulate a layer of high density plasma on the surface of the waveguide similar to that obtained by optical excitation of semiconductor structures. Experiments were performed to examine the far field radiation pattern, attenuation constant and the dispersion relation. Due to the presence of the plasma layer there will be an angular shift in the far field radiation pattern. We have observed angular shifts of about 20 in the radiation pattern of the waveguide before and after coating. Measurements are made in the frequency range of 88–95 GHz. This waveguide structure can be used to design an electronically steerable antenna and an electronic phase shifter operating in the millimeter-wave frequency band.Supported in part by the Army Research Office.     

A compact plasmonic tunable filter using elasto-optic effects

We report on the theoretical concept of the design of a compact plasmonic tunable filter made of a metal–dielectric–metal waveguide and using elasto-optic effects. The proposed device is designed in a nanoring resonator structure and numerically studied by means of 3D-FEM simulations. We obtained an optimized nanoring resonator that has a radius R=390 nm and resonances at the telecommunication wavelength of 1.58 μm. Simulations using elasto-optic material as the dielectric layer and top and bottom Ag layers as electrodes indicate that the output can be tuned in the telecommunication wavelength range with an applied field. Further, using the proposed device, optical switching phenomenon is also found to be possible. This tunable ring resonator filter with ultra-small radii is considered valuable for photonic integrated systems.     

InP阵列波导光栅的误差分析

在InP阵列波导光栅的制作过程中会引入不同的误差,从而影响器件的性能.为了最大限度地控制误差,提高半导体器件性能,本文采用传输函数法对InP基阵列波导光栅的系统误差和随机误差分别进行了分析.从系统误差的模拟结果中可以得到如下结论:深脊型波导的有效折射率n_c平均每偏移+0.000 1,中心波长偏移+0.05nm.相邻阵列波导长度差ΔL每偏移+0.01 μm,中心波长将偏移+0.44 nm.n_c和ΔL仅仅会影响到传输谱中心通道及其他各通道对应的波长,使得传输谱发生整体漂移,而信道间隔及串扰不会改变.罗兰圆半径R偏移不会影响器件的中心通道对应的波长,但会使其它通道对应的波长发生变化,最终使得信道间隔改变,R增加50 μm,信道间隔减小0.03 nm.从随机误差模拟结果中,得出:波导芯区折射率、上包层折射率、衬底折射率、波导宽度和波导芯层厚度的随机波动会对阵列波导光栅的串扰产生较大的影响.根据以上分析,可以通过控制不同参量来调节器件的中心波长以及信道间隔等来优化阵列波导光栅的光学性能.     

An optically pumped nanophotonic InP/InGaAlAs optical amplifier integrated on a SOI waveguide circuit

A small footprint integrated optical amplifier on Silicon-on-insulator is proposed in this article. By choosing to use optical pumping to drive the device, electrical contacting is avoided and the active waveguide can be made as thin as 100?nm, maximizing the optical confinement in the quantum well layers. Furthermore, the optical pumping is done through the silicon waveguide layer to optimally use the pump light. This leads to a compact device with high gain. We show 8?dB gain in pulsed regime in a 100?μm long device using a peak pump power of only 4.5?mW, while a comparable gain using an electrically pumped device would require an order of magnitude higher power consumption. This is an important step towards a CMOS-compatible optical amplifier for intra-chip optical interconnects.     

乐甫波结冰状态监测的响应机理分析

提出了将冰层进行多孔介质等效方法,对冰层、液体/波导层/压电基底多层乐甫(Love)波导结构建立分层介质模型,利用部分波理论和边界条件精确推导,分析不同状态下的传感响应,求解结冰过程Love波速度及声波衰减的变化,获得结冰过程中的声学传感机制。为了验证理论分析,实验制作了200 MHz的36°LiTaO₃/SiO₂波导结构的Love波器件,并构建模拟环境的试验系统对研制器件进行了实验测试。实验结果表明,利用Love波的工作频率以及插入损耗瞬变这一特征可以实现对结冰状态的准确监测。      

非线性一维光子晶体波导光双稳

利用非线性折射率系数较大且非线性时间响应较快的CdS_xSe_1-x玻璃为材料,设计并制备了非线性一维光子晶体波导光双稳器件,该器件的折射率空间分布呈正弦形式。实验测得双稳开关的阈值功率密度为1.60×10⁵W/cm²,开关时间为63ps。采用时域有限差分方法讨论了光子晶体带隙随入射光强变化而移动的情况,随着入射光功率密度的增加,光子晶体的带隙中心向短波方向移动。同时计算了该器件的双稳特性,理论计算得到双稳开关的阈值功率密度为1.40×10⁵W/cm²,开关时间约为50ps。获得了理论与实验基本一致的结果。     

A novel wavelength dispersive device with a dispersive element based on staircase-like straight and parallel arrayed waveguides

We propose a new type of arrayed waveguide grating (AWG) multiplexer/demultiplexer based on modified group refractive index. This device is composed by an array of straight and parallel waveguides of equal length and each waveguide consist of two sections with different width. The length of the two sections are changed from a waveguide to the adjacent one following a linear dependence resulting in a wavelength dispersive waveguide array. An example of the device design for silicon-on-insulator (SOI) platform is provided and numerical simulations have been carried out for various arrayed waveguide parameters. We demonstrate that the group index modification can be used for tailoring device dispersion properties, and that it can also result in new dispersion characteristics predicted numerically not observed in conventional AWGs. Additional advantages are that the demultiplexer does not necessarily require bending waveguide sections as in a conventional AWG (de)multiplexers, and thus yields highly compact devices with potentially very low insertion loss. Channel spacing of 1 nm have been predicted for sub-micron waveguides sizes. In this paper it is also proposed a novel wavefront converter based on waveguide array lens-like element with waveguides broadened sections. Numerical results for different input/output geometries are analized.     

毫米波大功率脉冲衰减器渐变结构的匹配研究

首先提出一种适合于毫米波大功率脉冲衰减器的结构形式，然后，用里兹－瑞利法分析了它的截面阻抗值，根据阻抗值，提出渐变线的一种优化方法。经实验验证，这种渐变结构的衰减器具有很低的驻波，同时也可有很高的功率容量。