紫外分光光度法测定富马酸二甲酯的含量

本文研究了用紫外分光光度法测定富马酸二甲酯含量的方法 ,探讨了测定过程中有关条件的变化对测定的影响 ,获得了测定的适宜条件 :波长 2 1 0± 2nm ;温度 1 9～ 2 5℃ ;无水乙醇为溶剂 ;测定体系的pH为7.2 5～ 8.2 5。DMF的含量与溶液的吸光度的关系为P =0 .0 933A +0 .0 4 1 6,经与色 -质谱分析结果对比表明本法具有较高的准确性     

2-(2-喹啉偶氮)-5-二乙氨基苯胺光度法测定钴

合成了新试剂 2 (2 喹啉偶氮 ) 5 二乙氨基苯胺 (QADEAA) ,并研究了其与钴的显色反应 ,在pH为5 .5的磷酸盐缓冲介质中 ,在CTMAB存在下 ,QADEAA与钴反应生成 2∶1稳定络合物 ;用磷酸酸化后 ,在酸介质中 ,体系λmax=6 2 5nm ,ε =1 .4 6× 1 0 5L·mol-1 ·cm-1 。钴含量在 0 .0 1～ 0 .30mg/L内符合比尔定律。方法用于大米、猪肝及水样中钴含量的测定 ,结果令人满意     

5-Br-PADAP-NO_2~--SCN~-三元离子缔合物分光光度法测定微量NO_2~-的研究

研究了在硫酸介质中 5 Br PADAP与NO-2 和SCN- 形成三元离子缔合物的最佳条件 ,其表观摩尔吸光系数ε550 =2 .4× 1 0 4 L/(mol·cm) ,缔合物组成比为n( 5 Br PADAP)∶n(NO-2 )∶n(SCN- ) =1∶1∶1 .提供了测定微量NO-2 离子的新方法 ,应用于环境水体中微量NO-2 离子的测定 ,结果较为满意。     

化学发光-化学需氧量测定新方法

根据重铬酸钾消解废水后其最终还原产物Cr3+ 浓度与COD值成正比关系 ,以及在碱性条件下 ,Luminol H2 O2 Cr3+ 体系产生很强的化学发光的原理 ,提出了一种用光电二极管做检测器测定水体的化学需氧量的新方法。本方法线性范围为 2 .1～ 60 0mg L,r2 =0 .9974;检出限为 2 .1mg L ;回收率为 1 0 0 %± 1 0 % ;RSD≤ 5 % (n =6)。用于实际样品测定 ,结果满意。     

芸香苷吸光光度法测定烟草中铁

在盐酸介质中 ,CTMAB存在下 ,芸香苷和Fe(Ⅲ )反应生成 2∶1蓝紫色络合物 ,λmax=6 2 0nm ,ε =4 .4 0× 10 4 L·mol- 1·cm- 1。铁含量在 0～ 2 0 μg/ 2 5ml范围内符合比耳定律 ,据此建立了一种测定烟草中铁含量的方法。     

阻抑褪色光度法测定微量硫代硫酸根

基于加热和pH =5 .0～ 6 .0条件下 ,硫代硫酸根抑制H2 O2 氧化结晶紫 (CV)的褪色反应 ,建立了测定硫代硫酸根的方法。硫代硫酸根在 4 .5× 1 0 -5～ 4 .5× 1 0 -4g/L范围内服从比耳定律 ,检出限为 3.2× 1 0 -6g/L。本法用于定影废液中硫代硫酸钠含量的测定 ,结果满意     

马来酸麦角新碱化学发光传感器的研究

基于发光试剂通过电价键将铁氰化钾固定在阴离子交换树脂上 ,可直接对待测物马来酸麦角新碱进行传感 ,从而建立测定药物马来酸麦角新碱的传感器新方法。其线性范围为 5× 10 -3 ～ 1mg/L ,线性方程为ΔI =10 6 .4 5C +17.10 (R2 =0 .998) ,检出限达到 2 .6 μg/L。对 0 .0 1和 0 .1mg/L的马来酸麦角新碱进行10次测定 ,它们的相对标准偏差 (RSD)分别为 2 .1%、2 .4 %。此传感器的稳定性良好 ,可连续使用 2 0 0次以上。此法已成功地用于马来酸麦角新碱注射液含量的测定以及尿样中马来酸麦角新碱含量的检测     

火焰原子吸收光谱法间接测定青霉素V钾

基于青霉素V钾在酸性条件下的水解产物可与Pb2 + 形成沉淀 ,用火焰原子吸收光谱法测定沉淀中铅的含量 ,可间接测定药片中青霉素V钾的含量。在优化条件下 ,测定青霉素V钾的线性范围为 5 .15× 10 -5～ 4 .12× 10 -4mol/L ,线性回归方程为A =2 .4 2× 10 3 c - 0 .0 6 3 1,相关系数为 0 .999 1,检出限为 7.392× 10 -7mol/L ,测定结果的相对标准偏差为 0 .0 6 %～ 0 .6 9% ,回收率为 97.8%～ 10 2 .0 %。     

阻抑褪色光度法测定微量硫代硫酸根

基于加热和pH =5 .0～ 6.0条件下 ,硫代硫酸根抑制H2 O2 氧化结晶紫 (CV)的褪色反应 ,建立了一种测定硫代硫酸根的方法。硫代硫酸根在 4.5× 1 0 -5～ 4.5× 1 0 -4g/L范围内服从比耳定律 ;检出限为 3 .2×1 0 -6g/L。本法用于定影废液中硫代硫酸钠含量的测定 ,结果满意。     

海水中二甲基硫亨利常数的测定

 推导了多次相平衡顶空气相色谱法测定海水中二甲基硫 (DMS)亨利常数 (K)的理论关系式 ,根据两次或多次气、液相平衡的关系式 ,只测定DMS在气相中的浓度就可测定亨利常数。实测 2 2℃时DMS在胶州湾海水中的亨利常数是 0 0 89,相对标准偏差为 5 5 0 %。亨利常数的对数与环境水体中NaCl的质量分数 [w(NaCl) ]之间的关系为 :logK =0 0 688·w(NaCl) - 1 3 5 68,相关系数为 0 997。亨利常数的对数与环境水体的绝对温度 (T)的倒数之间的相关方程为 :logK =- 15 4 4 8/T + 4 2 112 ,相关系数为 0 996。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Copper catalyzed/mediated synthetic methodology for ebselen and related isoselenazolones

Scope of the copper catalyzed/mediated selenium-nitrogen coupling reaction has been studied for the synthesis of isoselenazolones. It is noticed that the 2-chloro, 2-bromo-, and 2-iodo-aryl amides substrates can be exploited in the selenium-nitrogen coupling reaction by employing 25-100 mol % of CuI/1,10-phenanthroline (L) and potassium carbonate as a base in DMF. Furthermore, electron rich 2-chloro-arylamides also underwent selenium-nitrogen coupling reaction to give biologically important selenium-nitrogen heterocycles. Also, copper-catalyzed selenium-nitrogen coupling reaction has been meticulously applied for the synthesis of diaryl diselenides having methoxy, amine, and amide functionality from respective aryl iodides in the presence of stoichiometric amount of succinimide as an external Se-N coupling partner.     

Knoevenagel condensation catalyzed by novel Nmm-based ionic liquids in water

A series of novel N-methyl morpholine (Nmm) based ionic liquids with 1,2-propanediol group were synthesized and used as catalysts for Knoevenagel condensation at room temperature in water. Under the effect of the catalyst, various aldehydes or aliphatic ketones could react with a wide range of activated methylene compounds well, including malononitrile, alkyl cyanoacetate, cyanoacetamide, β-diketone, barbituric acid, 2-arylacetonitrile and thiazolidinedione. Furthermore, most of the products could be separated just by filtrating and washing with water. Additionally, the catalyst is recyclable and applicable for the large-scale synthesis.     

Construction of polyheterocyclic spirotetrahydrothiophene derivatives via sulfa-Michael/aldol cascade reaction

A series of polyheterocyclic spirotetrahydrothiophene derivatives were obtained in moderate to excellent yields via a catalyst-free sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 under mild conditions. We also present the first asymmetric sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 with moderate to good enantioselectivities catalyzed by readily available chiral phase-transfer catalysts (PTCs).     

Suzuki-Miyaura reactions of the soluble guanylate cyclase inhibitor NS2028: a non-product specific route to C-8 substituted analogues

Both soluble guanylate cyclase (sGC) inhibitors ODQ 1 and NS2028 2 are synthesized via improved protocols. In the former case treating 3,4-dihydroquinoxalin-2(1H)-one oxime 8, which can be prepared in two steps from 1,2-benzenediamine, with 1,1′-carbonyldiimidazole (CDI) gives the dihydro-ODQ 10 that in the presence of KMnO₄ oxidises to give ODQ 1 in an overall yield of 46% starting from 1,2-benzenediamine. In the latter case, the synthesis affords NS2028 2 from 2-amino-4-bromophenol 3 in three steps with an overall yield of 85% and avoids the need for chromatography. Furthermore, Suzuki-Miyaura reaction conditions are described that enable the preparation of 8-aryl and 8-heteroaryl derivatives of NS2028 directly from NS2028 2. Finally, demethylation of the 8-(methoxyphenyl) substituted analogues afforded the 8-(hydroxyphenyl) derivatives 40-42. All new products are fully characterised.