Effect of Device Fabrication Conditions on Photovoltaic Performance of Polymer Solar Cells Based on Poly(3‐hexylthiophene) and Indene‐C70 Bisadduct

Effect of the device fabrication conditions on photovoltaic performance of the polymer solar cells based on poly(3‐hexylthiophene) (P3HT) as donor and indene‐C₇₀ bisadduct (IC₇₀BA) as acceptor was studied systematically. The device fabrication conditions we studied include pre‐thermal annealing temperature, active layer thickness, and the P3HT:IC₇₀BA weight ratios. For devices with a 188‐nm‐thick active layer of P3HT:IC₇₀BA (1:1, w:w) blend film and pre‐thermal annealing at 150°C for 10 min, maximum power conversion efficiency (PCE) reached 5.82% with V_oc of 0.81 V, I_sc of 11.37 mA/cm², and FF of 64.0% under the illumination of AM1.5G, 100 mW/cm².     

Annealing effect on performance and morphology of photovoltaic devices based on poly(3‐hexylthiophene)‐b‐poly(ethylene oxide)

Novel block copolymers, poly(3‐hexylthiophene)‐b‐poly(ethylene oxide) (P3HT‐b‐PEO) were synthesized via Suzuki coupling reaction of P3HT and PEO homopolymers. The copolymers were characterized by NMR, gel permeation chromatography, differential scanning calorimeter, and UV–vis measurements. A series of devices based on the block copolymers with a fullerene derivative were evaluated after thermal or solvent annealing. The device using P3HT‐b‐PEO showed higher efficiency than using P3HT blend after thermal annealing. Phase‐separated structures in the thin films of block copolymer blends were investigated by atomic force microscopy to clarify the relationship between morphologies constructed by annealing and the device performance. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Photophysics and morphology of a polyfluorene donor–acceptor triblock copolymer for solar cells

We present a study of the optical, structural and device properties of a polyfluorene (PFM)‐based (PFM‐F8BT‐PFM) donor–acceptor triblock copolymer for use in an organic solar cell. Neutron reflectivity is employed to probe the vertical composition profile before and after thermal annealing while the crystallinity was examined using grazing incidence wide‐angle X‐ray. The absorption spectra and photoluminescence emission for the triblock and analogous blend of PFM with F8BT reveal a greater degree of intermixing in the triblock. However, the triblock copolymer exhibits exciplex emission, which necessitates a geminate polar pair; long‐lived exciplex states are detrimental in organic photovoltaic devices. The triplet yield in the triblock and the blend is estimated using photoinduced absorption, with the triblock copolymer generating a triplet population 20 times that of the blend. This is far from ideal as triplets are wasted states in organic photovoltaic devices and they can also act as scavengers of polarons reducing the efficiency even more. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1705–1718     

Functionally integrated liquid crystalline photochromic triple block copolymer with locally light‐ and thermal‐controllable sub‐blocks

Photoorientation and reorientation processes induced by illumination of the samples with oppositely directed polarized light and by the thermal treatment were studied for the films of triblock copolymer pAzo₁₀‐b‐pPhM₈₀‐b‐pAzo₁₀ consisting of a nematic phenyl benzoate сentral sub‐block (PhM, DP = 80) with two terminal smectic azobenzene sub‐blocks (Azo, DP = 10). For amorphized films of triblock copolymer, illumination with polarized light (λ = 546 nm) is shown to be by orientation of only Azo‐containing groups, but upon following annealing of the film, PhM groups are adjusted to the orientation of Azo fragments. It was found, that the subsequent illumination of the block copolymer sample with oppositely directed polarized light changes the orientation of azobenzene groups, while the orientation of phenyl benzoate groups is remained unchanged. Thus, the cyclic illumination of the triblock copolymer samples by the linear polarized light and subsequent thermal treatment make it possible to control and fix orientation of azobenzene and phenyl benzoate groups located in different sub‐blocks in the desired and independent manner. The comparison of these results with the data on random p(Azo₇‐ran‐PhM₃₀) copolymer of the similar composition revealed, that in the random copolymer, both Azo and PhM mesogenic groups are involved in the orientational cooperative process regardless of films process treatment. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1602–1611     

4,9‐Dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione functionalized copolymers for organic photovoltaic devices

The synthesis of conjugated polymers 1 – 5 functionalized with 4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione in the backbone is reported and their use in the construction of organic solar cells is demonstrated. Increasing the molar ratio of 2,7‐dibromo‐3,8‐dihexyl‐4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione, relative to 4,4′‐dihexyl‐5,5′‐dibromo‐2,2′‐bithiophene, in the copolymer synthesis significantly lowers the solubility of these polymers. The incorporation of highly conjugated 3,8‐dihexyl‐4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione unit into the polymer backbone has been confirmed by UV–vis absorption. The observation of decreasing quantum yield for the emission in the order of 1 , 2 , 3 is consistent with copolymers with different comonomer content. The power conversion efficiencies of solar cells using blends of these polymers with PCBM ([6,6]‐phenyl C₆₁‐butyric acid methyl ester) were determined to be 0.11% for polymer 1 , 0.33% for 2 , and 0.26% for 3 , respectively. Under identical white light illumination, the power conversion efficiency of the device based on polymer 2 /PCBM as the active layer was three times higher compared to that of device based on polymer 1 /PCBM. Owing to the limited solubility and poor film‐forming ability of polymer 3 , the power conversion efficiency of solar cell based on 3 /PCBM blend is lower than that of 2 /PCBM blend, but is still larger than that of 1 /PCBM blend. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2680–2688, 2008     

Synthesis and characterization of indeno[1,2‐b]fluorene‐based white light‐emitting copolymer

An indenofluorene‐based copolymer containing blue‐, green‐, and red light‐emitting moieties was synthesized by Suzuki polymerization and examined for application in white organic light‐emitting diodes (WOLEDs). Tetraoctylindenofluorene (IF), 2,1,3‐benzothiadiazole (BT), and 4,7‐bis(2‐thienyl)‐2,1,3‐benzothiadiazole (DBT) derivatives were used as the blue‐, green‐, and red‐light emitting structures, respectively. The number‐average molecular weight of the polymer was determined to be 25,900 g/mol with a polydispersity index of 2.02. The polymer was thermally stable (T_d = ～398 °C) and quite soluble in common organic solvents, forming an optical‐quality film by spin casting. The EL characteristics were fine‐tuned from the single copolymer through incomplete fluorescence energy transfer by adjusting the composition of the red/green/blue units in the copolymer. The EL device using the indenofluorene‐based copolymer containing 0.01 mol % BT and 0.02 mol % DBT units ( PIF‐BT01‐DBT02 ) showed a maximum brightness of 4088 cd/m² at 8 V and a maximum current efficiency of 0.36 cd/A with Commission Internationale de L'Eclairage (CIE) coordinates of (0.34, 0.32). The EL emission of PIF‐BT01‐DBT02 was stable with respect to changes in voltage. The color emitted was dependent on the thickness of the active polymer layer; layer (～60 nm) too thin was unsuitable for realizing WOLED via energy transfer. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3467–3479, 2009     

White electroluminescent single‐polymer achieved by incorporating three polyfluorene blue arms into a star‐shaped orange core

A series of star‐like dopant/host single‐polymer systems with a D‐A type star‐shaped orange core and three blue polyfluorene arms were designed and synthesized. Through tuning the doping concentration of the orange core and thermal annealing treatment of white polymer light‐emitting diodes based on them, highly efficient white electroluminescence has been achieved. A typical single‐layer device (ITO/PEDOT:PSS/polymer/Ca/Al) realized pure white emission with a luminous efficiency of 16.62 cd A^?1, an external quantum efficiency of 6.28% and CIE coordinates of (0.33, 0.36) for S‐WP‐002TPB3 containing 0.02 mol % orange core. The high efficiency of the devices could be mainly attributed to the suppressed concentration quenching of the dopant units, more efficient energy transfer from polymer host to orange dopant and thermal annealing‐induced α‐phase polyfluorene (PF) self‐dopant in amorphous PF host. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Immobilization of AIEgens into metal‐organic frameworks: Ligand design,emission behavior,and applications

Aggregation‐induced emission (AIE), in which the luminophores are highly emissive in aggregate state, is one of the most unique photophysical phenomena and has shown interesting applications in many areas. The immobilization of AIE luminogens (AIEgens) into metal‐organic frameworks (MOFs), which are inorganic‐organic hybrid porous materials with tunable and predictable structures, has been investigated over the past few years. These well‐defined porous frameworks cannot only provide an ideal platform for studying the mechanism of AIE phenomenon in solid state, but also show potential applications from sensing to white light‐emitting diodes. In this highlight, we will summarize the recent progress of AIEgens‐based MOFs, including ligand design, emission behavior, and applications. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1809–1817     

Thermally crosslinkable hole‐transporting poly(fluorene‐co‐triphenylamine) for multilayer polymer light‐emitting diodes

This article reports the synthesis and characterization of a novel thermally crosslinkable hole‐transporting poly (fluorene‐co‐triphenylamine) (PFO‐TPA) by Suzuki coupling reaction, followed with its application in the fabrication of multilayer light‐emitting diodes by wet processes. The thermal, photophysical, and electrochemical properties of PFO‐TPA were investigated by differential scanning calorimeter, thermogravimetric analysis, optical spectroscopy, and cyclic voltammetry, respectively. Thermally crosslinked PFO‐TPA, through pendant styryl groups, demonstrates excellent thermal stability (T_d > 400 °C, T_g = 152 °C), solvent resistance, and film homogeneity. Its highest occupied molecular orbital level (?5.30 eV) lies between those of PEDOT:PSS (?5.0 ～ ?5.2 eV) and poly(9,9‐dioctylfluorene) (PFO: ?5.70 eV), forming a stepwise energy ladder to facilitate hole injection. Multilayer device with crosslinked PFO‐TPA as hole‐injection layer (HIL) (ITO/PEDOT:PSS/HIL/PFO/LiF/Ca/Al) was readily fabricated by successive spin‐coating processes, its maximum luminance efficiency (3.16 cd/A) were about six times higher than those without PFO‐TPA layer (0.50 cd/A). The result of hole‐only device also confirmed hole‐injection and hole‐transport abilities of crosslinked PFO‐TPA layer. Consequently, the device performance enhancement is attributed to more balanced charges injection in the presence of crosslinked PFO‐TPA layer. The thermally crosslinkable PFO‐TPA is a promising material for the fabrication of efficient multilayer polymer light‐emitting diodes because it is not only a hole‐transporting polymer but also thermally crosslinkable. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

White‐Light Electroluminescence with Tetraphenylethylene as Emitting Layer of Aggregation‐Induced Emissions Enhancement

Tetraphenylethylene (TPE) based molecules with easy synthesis, good thermal stability, and especially their aggregation‐induced emissions enhancement (AIEE) effect recently become attractive organic emitting materials due to their potentially practical application in OLEDs. Herein, the AIEE behaviors of tetraphenylethylene dyes (TMTPE and TBTPE) were investigated. Fabricated luminesent device using TMTPE dye as emitting layer displays two strong emitting bands: the blue emission coming from the first‐step aggregation and the yellow emission attributed to the second‐step aggregation. Thus, it can be utilized to fabricate the white‐light OLEDs (WOLEDs) of the single‐emitting‐component. A three‐layer device with the brightness of 1200 cd·m^?2 and current ef?ciency of 0.78 cd·A^?1 emits the close to white light with the CIE coordinates of x=0.333 andy=0.358, when applied voltage from 8–13 V, verifying that the TPE‐based dyes of AIEE effect can be effectively applied in single‐emitting‐component WOLEDs fabrication.     

Poly(triarylamine): Its synthesis,properties, and blend with polyfluorene for white‐light electroluminescence

A new high‐molecular‐weight poly(triarylamine), poly[di(1‐naphthyl)‐4‐anisylamine] (PDNAA), was successfully synthesized by oxidative coupling polymerization from di(1‐naphthyl)‐4‐anisylamine (DNAA) with FeCl₃ as an oxidant. PDNAA was readily soluble in common organic solvents and could be processed into freestanding films with high thermal decomposition and softening temperatures. Cyclic voltammograms of DNAA and PDNAA exhibited reversible oxidative redox couples at the potentials of 0.85 and 0.85 V, respectively, because of the oxidation of the main‐chain triarylamine unit. This suggested that PDNAA is a hole‐transporting material with an estimated HOMO level of 5.19 eV. The absorption maximum of a PDNAA film appeared at 370 nm, with an estimated band gap of 2.86 eV from the absorption edge. Unusual multiple photoluminescence maxima were observed at 546 nm, and this suggested its potential application in white‐light‐emission devices. Nearly white‐light‐emission devices could be obtained with either a bilayer‐structure approach {indium tin oxide/poly(ethylenedioxythiophene):poly(styrene sulfonate)/PDNAA/poly[2,7‐(9,9‐dihexylfluorene)] (PF)/Ca} or a polymer‐blend approach (PF/PDNAA = 95:5). The luminance yield and maximum external quantum efficiency of the light‐emitting diode with the PF/PDNAA blend as the emissive layer were 1.29 cd/A and 0.71%, respectively, and were significantly higher than those of the homopolymer. This study suggests that the PDNAA is a versatile material for electronic and optoelectronic applications. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1727–1736, 2007     

Stabilization of the film morphology in polymer: Fullerene heterojunction solar cells with photocrosslinkable bromine‐functionalized low‐bandgap copolymers

Novel bromine‐functionalized photocrosslinkable low‐bandgap copolymers, PBDTTT‐Br25 and PBDTTT‐Br50, are synthesized via Stille cross‐coupling polymerization for the purpose of stabilizing the film morphology in polymer solar cells (PSCs). Photocrosslinking of PBDTTT‐Br25 and PBDTTT‐Br50 copolymers dramatically improves the solvent resistance of the active layer without disrupting the molecular ordering and charge transport, which is confirmed by the insolubility of the films washed by organic solvents and by their thermal behavior. As a result, the formation of large aggregations of fullerene is suppressed in polymer:fullerene blend films even after prolonged thermal annealing, and the stability of the device is enhanced when compared with cells based on noncrosslinkable PBDTTT. The power conversion efficiency of the PSCs based on PBDTTT‐Br25 and PBDTTT‐Br50 reaches 5.17% and 4.48%, respectively, which is improved obviously in comparison with that (4.26%) of the PSCs based on the control polymer PBDTTT. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3123–3131     

Nanocrystalline cellulose/fluorinated polyacrylate latex via RAFT‐mediated surfactant‐free emulsion polymerization and its application as waterborne textile finishing agent

A simple method for nanocrystalline cellulose (NCC)/fluorinated polyacrylate was developed by RAFT‐mediated surfactant‐free emulsion polymerization, in which the nanocomposites formed a core‐shell spherical morphology. The influence of the content of NCC‐g‐(PAA‐b‐PHFBA) (AA was acrylic acid, HFBA was hexafluorobutyl acrylate) on the properties of latex and film were systematically studied. The monomer conversion, the tensile strength, and water–oil repellency of film increased first and then decreased, the latex particle size decreased first and then decreased, when the content of NCC‐g‐(PAA‐b‐PHFBA) increased from 1 to 6 wt %. Elongation at break and thermal stability distinctly decreased when the content of NCC‐g‐(PAA‐b‐PHFBA) gradually increased. XPS showed that the fluorine‐containing groups well concentrated at the film–air interfaces during the annealing process. SEM analysis revealed that the treated fiber had a rugged surface, and the treated fabric had an excellent water repellency. In addition, this green grafting method in water offered a new perspective for the fabrication of exceptional NCC‐based nanocomposites with NCC as the core and also helped to promote the potential applicability of NCC in a range of multipurpose applications. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1305–1314     

One‐pot synthesis of polymer/inorganic hybrids: toward readily accessible,low‐loss,and highly tunable refractive index materials and patterns

The realization that modulated light pulses can be transported in a confined fashion over long distances within a structure that comprises a controlled spatial distribution of the refractive index n—as in optical fibres and waveguides—has, without doubt, underpinned the telecommunications revolution witnessed during the 20th century. The refractive index n, quantifying how light propagates in a given medium, as a consequence, has become one of the most important materials properties in designing photonics products. The other key characteristic for most optical and photonic applications is the amount of light that is absorbed by a material, expressed as the extinction coefficient κ. Although a range of organic/inorganic hybrid materials have been advanced with tunable refractive index, only a few systems combine a high n, sufficiently low κ and straightforward sample preparation to allow simple fabrication of highly transparent, low‐loss structures. Here, we present a hybrid material that can be readily produced in water via a one‐pot synthesis directly from commercially available, low‐cost precursors. Moreover, our hybrid material can be solution‐processed, yielding systems of an extinction coefficient <0.01, and a refractive index, which can be controlled to adopt values between 1.5 to at least 2.1. Unprecedentedly, simple post‐deposition procedures such as thermal annealing or irradiation with high‐intensity UV‐light allow adjusting n also after film fabrication, offering an exceptional degree of freedom in designing and tailoring also more complex photonic architectures or planar wave‐guides, for example, through creation of in‐plane refractive index patterns. As a proof‐of‐concept, we demonstrate fabrication of waveguides based on local heating. The versatility of our materials is further illustrated by the production of lenses and dielectric filters of ～100% reflectivity in a given wavelength regime. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 000: 000–000, 2011     

Improvement of thermoplasticity for s‐BPDA/PDA by copolymerization and blend with novel asymmetric BPDA‐based polyimides

Asymmetric biphenyl type polyimides (PI) derived from 2,3,3′,4′‐biphenyltetracarboxylic dianhydride (a‐BPDA) and p‐phenylenediamine (PDA) or 4,4′‐oxydianiline (ODA) show higher T_gs, and much better thermoplasticity than the corresponding isomeric PIs from symmetric 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (s‐BPDA). In addition, a‐BPDA‐derived PIs are completely amorphous owing to their bent chain structures and highly distorted conformations, whereas the PIs from s‐BPDA are semicrystalline. a‐BPDA‐derived PIs possessing these properties or the a‐BPDA monomer were used as a flexible blend component or a comonomer to improve the insufficient thermoplasticity of semirigid s‐BPDA/PDA homo polymer. The blends composed of s‐BPDA/PDA (80%) with a‐BPDA‐derived PIs (20%), as well as the s‐BPDA/PDA‐based copolymer containing 20% a‐BPDA, showed a certain extent of thermoplasticity above the T_gs without causing a decrease in T_g. In addition, these blends and copolymer provided comparatively low thermal expansion coefficient (ca. 18 ppm). The improved film properties for the blends are related to good blend miscibility. On the other hand, when s‐BPDA/ODA was used as a flexible matrix polymer instead of a‐BPDA‐derived PIs, the 80/20 blend film annealed at 400°C exhibited no prominent softening at the T_g. This result arises from annealing‐induced crystallization of the flexible s‐BPDA/ODA component. Thus, these results revealed that a‐BPDA‐derived PIs are promising candidates as matrix polymers for semirigid s‐BPDA/PDA for the present purpose. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2499–2511, 1999     

Miscibility and phase structure of binary blends of polylactide and poly(methyl methacrylate)

Blends of amorphous poly(DL‐lactide) (DL‐PLA) and crystalline poly(L‐lactide) (PLLA) with poly(methyl methacrylate) (PMMA) were prepared by both solution/precipitation and solution‐casting film methods. The miscibility, crystallization behavior, and component interaction of these blends were examined by differential scanning calorimetry. Only one glass‐transition temperature (T_g) was found in the DL‐PLA/PMMA solution/precipitation blends, indicating miscibility in this system. Two isolated T_g's appeared in the DL‐PLA/PMMA solution‐casting film blends, suggesting two segregated phases in the blend system, but evidence showed that two components were partially miscible. In the PLLA/PMMA blend, the crystallization of PLLA was greatly restricted by amorphous PMMA. Once the thermal history of the blend was destroyed, PLLA and PMMA were miscible. The T_g composition relationship for both DL‐PLA/PMMA and PLLA/PMMA miscible systems obeyed the Gordon–Taylor equation. Experiment results indicated that there is no more favorable trend of DL‐PLA to form miscible blends with PMMA than PLLA when PLLA is in the amorphous state. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 23–30, 2003     

White light electroluminescence from graphene‐enhanced single polymer comprising two color emitters of equal molar ratios

White polymeric light‐emitting diode (WPLED) based on a single polymer, poly(3‐hexylthiophene‐alt‐9,9‐dioctylfluorene) (PTAF), has been successfully demonstrated. This conjugated alternating copolymer, PTAF, comprises 50 mol % of 3‐hexylthiophene which is an orange‐red color chromophore and 50 mol % 9,9‐dioctylfluorene which is a bluish‐green color chromophore. It was synthesized by Suzuki cross‐coupling reaction and has a molecular weight of 15,021 and polydispersity of 1.36. Nanocomposite consisting PTAF and graphene nanosheets enhances the optoelectronic properties and the device fabricated with a configuration of ITO/PEDOT:PSS/(PTAF + 1% graphene)/Ca/Al shows two‐color white electroluminescence with CIE 1931 coordinates of (0.28, 0.34). The white luminescence from a single polymer affords the WPLED device a simple structure and low fabrication cost. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Synthesis,characterization, photo‐induced alignment,and surface orientation of poly(9,9‐dioctylfluorene‐alt‐azobenzene)s

Three types of bi‐functionalized copolymers ( P1FAz , P2FAz , and P3FAz ) with different numbers of fluorene units and an azobenzene unit were synthesized and characterized using UV–vis and polarized absorption spectroanalysis. The trans‐cis photoisomerization was conformed under 400 nm light irradiation for all copolymers in chloroform. However, in the film state, only the trans‐cis photoisomerization occurred by mono‐fluorene attached copolymer poly[(9,9‐di‐n‐octylfluorenyl‐2,7‐diyl)‐alt‐4,4′‐azobenzene)] ( P1FAz ). Photo‐induced alignment was achieved using the P1FAz film after irradiation with linear polarized 400 nm light and subsequent annealing at 60 °C. Surface orientation of a spin‐coating film of poly(9,9‐didodecylfluorene) ( F12 ) was achieved using the photo‐induced alignment layer of the P1FAz film after annealing at 90 °C. The photo‐induced alignment layer of P1FAz has potential application to the surface orientation technique for appropriate polymers, which will be useful for the fabrication of optoelectronics devices. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Polymers for application in organic solar cells: Bithiophene can work better than thienothiophene when coupled to benzodithiophene

The synthesis and characterization of two low band gap copolymers ( P1 and P2 ) incorporating benzo[1,2‐b:4,5‐b']dithiophene unit substituted with octylsulfanylthienyl groups (OSBT) are here reported. These materials, designed to be employed in polymer solar cells (PSCs), were obtained from alternating OSBT and bithiophene ( P1 ) or thienothiophene ( P2 ) units. Their structural electrochemical and photophysical properties were investigated. They are thermally stable and soluble in organic solvents from which they easily form films. They also form π‐stacks in solution, in film and display a moderate solvatochromism. These polymers were tested with [70]PCBM in bulk‐heterojunction (BHJ) PSCs where they act as donor materials and [70]PCBM is the electron acceptor. The best device, obtained using a 1:3 weight ratio for the P1 :[70]PCBM blend, shows a PCE around 1.5%. A broad response from 350 to 700 nm is also observed in the external quantum efficiency (EQE) curves, wider for P1 with respect to P2 . © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1603–1614     

In situ film characterization of thermally treated microstructured conducting polymer films

Based on a low‐cost fabrication routine microstructured conducting polymer films of poly (dioctylfluorene‐co‐benzothiadiazole) (F8BT) are prepared without any heat treatment or vacuum steps. The influence of thermal annealing at temperatures below the glass transition temperature of F8BT on such microstructured channel structures is investigated. In the applied structuring routine, a F8BT film is spin coated on a channel‐type hard master structure and afterwards floated on a flat support. Thereby, the properties of the final polymeric structures, for example channel width and height, can be tuned by simply varying the polymer concentration in solution and using the same master structure. With in situ grazing incidence small angle X‐ray scattering and imaging ellipsometry the installed channel structure and the influence of thermal treatment are probed. A complex interplay between a macroscopic polymer flow (reduced channel heights) and a molecular rearrangement (formation of mesoscopic crystallites) takes place during thermal annealing. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012