Effects of additives and post‐treatment on the thermoelectric performance of vapor‐phase polymerized PEDOT films

Vapor‐phase polymerization (VPP) is an important method for the fabrication of high‐quality conducting polymers, especially poly(3,4‐ethylenedioxythiophene) (PEDOT). In this work, the effects of additives and post‐treatment solvents on the thermoelectric (TE) performance of VPP‐PEDOT films were systematically investigated. The use of 1‐butyl‐3‐menthylinidazolium tetrafluoroborate ([BMIm][BF₄], an ionic liquid) was shown to significantly enhance the electrical conductivity of VPP‐PEDOT films compared with other additives. The VPP‐PEDOT film post‐treated with mixed ethylene glycol (EG)/[BMIm][BF₄] solvent displayed the high power factor of 45.3 μW m^?1 K^?2 which is 122% higher than that prepared without any additive or post‐treatment solvent, along with enhanced electrical conductivity and Seebeck coefficient. This work highlighted the superior effect of the [BMIm][BF₄] additive and the EG/[BMIm][BF₄] solvent post‐treatment on the TE performance of the VPP‐PEDOT film. These results should help with developing the VPP method to fabricate high‐performance PEDOT films. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 1738–1744     

Why does the electrical conductivity in PEDOT:PSS decrease with PSS content? A study combining thermoelectric measurements with impedance spectroscopy

We have investigated the electrical transport properties of poly(3,4‐ethylenedioxythiophen)/poly(4‐styrene‐sulfonate) (PEDOT:PSS) with PEDOT‐to‐PSS ratios from 1:1 to 1:30. By combining impedance spectroscopy with thermoelectric measurements, we are able to independently determine the variation of electrical conductivity and charge carrier density with PSS content. We find the charge carrier density to be independent of the PSS content. Using a generalized effective media theory, we show that the electrical conductivity in PEDOT:PSS can be understood as percolation between sites of highly conducting PEDOT:PSS complexes with a conductivity of 2.3 (Ωcm)^?1 in a matrix of excess PSS with a low conductivity of 10^?3 (Ω cm)^?1. In addition to the transport properties, the thermoelectric power factors and Seebeck coefficients have been determined. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Paper: An effective substrate for the enhancement of thermoelectric properties in PEDOT:PSS

A novel strategy via paper as an effective substrate has been introduced as a thermoelectric material in this work. Free‐standing poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS)/paper composite films are conveniently prepared by a one‐step method of directly writing PEDOT:PSS solution on paper, making the process simple, rapid, and facile. The free‐standing composite films display excellent flexibility, light weight, soaking stability in water, and great potential in large‐scale production. Improved thermoelectric properties are obtained in PEDOT:PSS/paper composite films, owing to the simultaneously enhanced Seebeck coefficient (30.6 μV K^?1) and electrical conductivity, and a low thermal conductivity (0.16 W m^?1 K^?1) compared with pristine PEDOT:PSS films. The results indicate that paper as an effective substrate is suitable for the preparation of high‐performance and flexible thermoelectric materials. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 737–742     

An effective approach to enhanced thermoelectric properties of PEDOT:PSS films by a DES post‐treatment

As conventional organic solvents present inherent toxicity, deep eutectic solvents (DES) have been considered as excellent candidates due to their green characteristics. In this work, thermoelectric properties enhancement of PEDOT:PSS films is achieved by introducing DES as an additive and post‐treatment reagent. Direct addition and post‐treatment approaches lead to a maximum Seebeck coefficient of 29.1 μV K^?1 and electrical conductivity of 620.6 S cm^?1, respectively. In addition, an optimal power factor is obtained by DES post‐treatment, reaching up to 24.08 μW m^?1 K^?2, which is approximately four orders of magnitude higher than the pure PEDOT:PSS. Assuming a thermal conductivity of 0.17 W m^?1 K^?1, the maximum ZT value is estimated to be 0.042 at 300 K. Further, atomic force microscopy and X‐ray photoelectron spectroscopy are performed and suggest that the remarkably enhanced electrical conductivity originates from the removal of the excess insulating PSS and the phase separation between the PEDOT and PSS chains. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 885–892     

Thermoelectric behavior of organic thin film nanocomposites

Organic thin film nanocomposites, prepared by liquid‐phase exfoliation, were investigated for their superior electrical properties and thermoelectric behavior. Single‐walled carbon nanotubes (SWNT) were stabilized by intrinsically conductive poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) in an aqueous solution. The electrical conductivity (σ) was found to increase linearly as 20 to 95 wt % SWNT. At 95 wt % SWNT, these thin films exhibit metallic electrical conductivity (～4.0 × 10⁵ S m^?1) that is among the highest values ever reported for a free‐standing, fully organic material. The thermopower (S) remains relatively unaltered as the electrical conductivity increases, leading to a maximum power factor (S²σ) of 140 μW m^?1 K^?2. This power factor is within an order of magnitude of bismuth telluride, so it is believed that these flexible films could be used for some unique thermoelectric applications requiring mechanical flexibility and printability. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Thermoelectric properties of PEDOT films prepared by electrochemical polymerization

Thermoelectric (TE) properties of flexible and free‐standing poly(3,4‐ethylenedioxythiophene) (PEDOT) films synthesized via galvanostatic polymerization of 3,4‐ethylenedioxythiophene in propylene carbonate containing sulfated poly(β‐hydroxyethers) (S‐PHE) as polymer electrolyte were elaborately studied. Both electrical conductivities (σ ) and Seebeck coefficients (S ) of the PEDOT:S‐PHE films were increased by decreasing the temperature (T ) or by increasing the current density (J ) during electrosynthesis. Possible reasons for the lack of a trade‐off relation commonly observed between σ and S are discussed on the basis of SEM and oxidation‐level measurements. Preparation of the PEDOT:S‐PHE films was optimized with respect to T and J . In addition, the oxidation level of the PEDOT:S‐PHE films was controlled by potential and the change of their TE performances was discussed in conjunction with the change of chemical species involved. The power factor (PF = σS ²) of the PEDOT:S‐PHE films reached 7.9 μW m^?1 K^?2, leading to a dimensionless TE figure‐of‐merit (ZT ) of 0.013. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 524–531     

Efficient enhancement of the thermoelectric performance of vapor phase polymerized poly(3,4‐ethylenedioxythiophene) films with poly(ethyleneimine)

Tuning the molecular rearrangement and oxidation level has been proven to be effective strategies for optimizing the thermoelectric (TE) performance of PEDOT. It is difficult to achieve these effects simultaneously via a one‐step process, however. In this work, we combined vapor phase polymerization (VPP) and H₂SO₄ post‐treatment to obtain a highly conductive PEDOT film. A novel strategy using polyethylenemine (PEI) as an effective reducing agent was employed to enhance the thermopower of the PEDOT film. Grazing‐Incidence Wide‐Angle X‐ray Scattering analysis and the changes in the oxidation level allow us to elucidate the role of PEI and its transport mechanism. It is demonstrated that the thermopower of well‐ordered crystallites in the PEDOT film significantly increases more than five times (from 11 to 59 μV K^?1) by the PEI‐DMF solution immersion process, while the electrical conductivity is maintained at 100 S cm^?1. The promising method connecting VPP, H₂SO₄, and PEI shows great potential for effectively tuning the thermopower of organic TE materials. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 257–265     

Influence of imidazole‐based acidity control of PEDOT:PSS on its electrical properties and environmental stability

Poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) has been studied for a wide range of applications due to its potential as a transparent electrode. Herein, the use of imidazole and its derivatives as a neutralizing additive for PEDOT:PSS dispersion and in‐depth studies of their effects in terms of electrical properties and stability is reported. Although the neutralization in general reduces the electrical conductivity of PEDOT:PSS, the conductivity after imidazole treatment (685.2 S cm^?1) is higher than that after treatment of other derivatives. Spectroscopic and thermoelectric studies show that the de‐doping effect resulted in the conductivity reduction. As a trade‐off of the conductivity reduction, greatly enhanced long‐term stability and noncorrosive characteristics are obtained after neutralization. The change in sheet resistance of imidazole‐treated PEDOT:PSS after 500 h under harsh conditions (85 °C and 85% humidity) is half that of the untreated samples, demonstrating the great enhancement of the stability. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1530–1536     

Effect of (3‐glycidyloxypropyl)trimethoxysilane (GOPS) on the electrical properties of PEDOT:PSS films

Poly(3,4‐ethylenedioxythiophene) doped with poly(styrenesulfonate) (PEDOT:PSS) has been reported as a successful functional material in a broad variety of applications. One of the most important advantages of PEDOT:PSS is its water‐solubility, which enables simple and environmental friendly manufacturing processes. Unfortunately, this also implies that pristine PEDOT:PSS films are unsuitable for applications in aqueous environments. To reach stability in polar solvents, (3‐glycidyloxypropyl)trimethoxysilane (GOPS) is typically used to cross‐link PEDOT:PSS. Although this strategy is widely used, its mechanism and effect on PEDOT:PSS performance have not been articulated yet. Here, we present a broad study that provides a better understanding of the effect of GOPS on the electrical and electronic properties of PEDOT:PSS. We show that the GOPS reacts with the sulfonic acid group of the excess PSS, causing a change in the PEDOT:PSS film morphology, while the oxidation level of PEDOT remains unaffected. This is at the origin of the observed conductivity changes. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 814–820     

Conductivity enhancement of PEDOT:PSS film via sulfonic acid modification: application as transparent electrode for ITO-free polymer solar cells

3-Hydroxy-1-propanesulfonic acid(HPSA)was applied as a modification layer on poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate)(PEDOT:PSS)film via spin-coating,resulting in a massive boost of the conductivity of PEDOT:PSS film,and thus the as-formed PEDOT:PSS/HPSA bilayer film was successfully used as a transparent electrode for ITO-free polymer solar cells(PSCs).Under the optimized concentration of HPSA(0.2 mol L~(-1)),the PEDOT:PSS/HPSA bilayer film has a conductivity of 1020 S cm~(-1),which is improved by about 1400 times of the pristine PEDOT:PSS film(0.7 S cm~(-1)).The sheet resistance of the PEDOT:PSS/HPSA bilayer film was 98Ωsq~(-1),and its transparency in the visible range was over 80%.Both parameters are comparable to those of ITO,enabling its suitability as the transparent electrode.According to atomic force microscopy(AFM),UV-Vis and Raman spectroscopic measurements,the conductivity enhancement was resulted from the removal of PSS moiety by methanol solvent and HPSA-induced segregation of insulating PSS chains along with the conformation transition of the conductive PEDOT chains within PEDOT:PSS.Upon applying PEDOT:PSS/HPSA bilayer film as the transparent electrode substituting ITO,the ITO-free polymer solar cells(PSCs)based on poly[N-9″-hepta-decanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)]:[6,6]-phenyl C71-butyric acid methyl ester(PC_(71)BM)(PCDTBT:PC_(71)BM)active layer exhibited a power conversion efficiency(PCE)of 5.52%,which is comparable to that of the traditional ITO-based devices.     

Secondary doping in poly(3,4‐ethylenedioxythiophene):Poly(4‐styrenesulfonate) thin films

The electrical and structural properties of poly(3,4‐ethylenedioxythiophene):poly(4‐styrenesulfonate) (PEDOT:PSS) thin films deposited from aqueous dispersion using different concentrations of selected secondary dopants are studied in detail. An improvement of the electrical conductivity by three orders of magnitude is achieved for dimethyl sulfoxide, sorbitol, ethylene glycol, and N,N‐dimethylformamide, and the secondary dopant concentration dependence of the conductivity exhibits almost identical behavior for all investigated secondary dopants. Detailed analysis of the surface morphology and Raman spectra reveals no presence of the secondary dopant in fabricated films, and thus the dopants are truly causing the secondary doping effect. Although the ratio of benzenoid and quinoid vibrations in Raman spectra is unaffected by doping, the phase transition in PEDOT:PSS films owing to doping is confirmed. Further analysis of temperature‐dependent conductivity reveals 1D variable range hopping (VRH) charge transport for undoped PEDOT:PSS, whereas highly conductive doped PEDOT:PSS films exhibit 3D VRH charge transport. We demonstrate that the charge ‐ hopping dimensionality change should be a fundamental reason for the conductivity enhancement. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1139–1146     

Poly(thieno[3,4‐b]‐1,4‐oxathiane) and poly(3,4‐ethylenedioxythiophene‐co‐thieno[3,4‐b]‐1,4‐oxathiane)/poly(styrene sulfonic sodium): Preparation,characterization, and optoelectronic performance

In this work, the asymmetrical analog of 3,4‐ethylenedioxythiophene (EDOT), thieno[3,4‐b]‐1,4‐oxathiane (EOTT), was synthesized and chemically polymerized first in aqueous solution using poly(styrene sulfonic sodium) (PSS) as the polyelectrolyte to yield poly(thieno[3,4‐b]‐1,4‐oxathiane) (PEOTT)/PSS. As‐formed film exhibited low electrical conductivity (～10^?4 S/cm). Alternatively, EOTT together with EDOT (in different molar ratio of 1:1 and 1:5) was copolymerized and the polymer poly(EOTT‐co‐EDOT)/PSS had electrical conductivity of 10^?1 S/cm. After dimethyl sulfoxide (DMSO) treatment, the electrical conductivity was enhanced to 10⁰ S/cm; however, the conductivity of the above homopolymer was reduced (～10^?5 S/cm). Raman spectroscopy was used to interpret conductivity enhancement or reduction after DMSO treatment. The conductivity decrease of PEOTT/PSS compared to poly(EOTT‐co‐EDOT)/PSS may arise from the conformational change of PEOTT backbone from the quasi‐planar to the distorted planar mode induced by PSS^–/PSSH through ionic interaction. Kinetic studies revealed that the copolymer had high coloration efficiencies (375 cm²/C), low switching voltages (?0.8 to +0.6 V), decent contrast ratios (45%), moderate response time (1.0 s), excellent stability, and color persistence. An electrochromic device employing poly(3‐methylthiophene) and poly(EOTT‐co‐EDOT)/PSS as the anode and cathode materials was also studied. From these results, poly(EOTT‐co‐EDOT)/PSS would be a promising candidate material for organic electronics. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2285–2297     

Free‐Standing Conducting Polymer Films for High‐Performance Energy Devices

Thick, uniform, easily processed, highly conductive polymer films are desirable as electrodes for solar cells as well as polymer capacitors. Here, a novel scalable strategy is developed to prepare highly conductive thick poly(3,4‐ethylenedioxythiophene):polystyrene sulfonate (HCT‐PEDOT:PSS) films with layered structure that display a conductivity of 1400 S cm^?1 and a low sheet resistance of 0.59 ohm sq^?1. Organic solar cells with laminated HCT‐PEDOT:PSS exhibit a performance comparable to the reference devices with vacuum‐deposited Ag top electrodes. More importantly, the HCT‐PEDOT:PSS film delivers a specific capacitance of 120 F g^?1 at a current density of 0.4 A g^?1. All‐solid‐state flexible symmetric supercapacitors with the HCT‐PEDOT:PSS films display a high volumetric energy density of 6.80 mWh cm^?3 at a power density of 100 mW cm^?3 and 3.15 mWh cm^?3 at a very high power density of 16160 mW cm^?3 that outperforms previous reported solid‐state supercapacitors based on PEDOT materials.     

Growth of poly(3,4‐ethylenedioxythiophene) films prepared by base‐inhibited vapor phase polymerization

Transparent [90% transmittance at 550 nm at a sheet resistance (R_s) of 279 Ω sq^?1] poly(3,4‐ethylenedioxythiophene) (PEDOT) films with electrical conductivities up to 1354 S cm^?1 are prepared using base‐inhibited vapor phase polymerization at atmospheric pressure. The influence of reaction conditions, such as temperature and growth time, on the film formation is investigated. A simple and convenient two‐electrode method is used for the in situ measurement of resistance, enabling to investigate the growth mechanism of polymer films and the influence of different parameters (relative humidity and the amount of oxidant) on the film growth. Low humidity exerts a detrimental effect on film growth and conductivity. In situ R_s measurements suggest that a large structural change occurs upon washing the PEDOT‐oxidant film. © 2014 Wiley Periodicals, Inc. J Polym Sci Part B: Polym. Phys. 2014 , 52, 561–571     

Emulsion synthesis of nanoparticles containing PEDOT using conducting polymeric surfactant: Synergy for colloid stability and intercalation doping

Poly(3,4‐ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) is a widely used conductive aqueous dispersion synthesized by using emulsion polymerization method. To further enhance its solution processability and conductivity of PEDOT derivatives, we proposed to replace the nonconductive PSS with conductive poly[2‐(3thienyl)‐ethoxy‐4‐butylsulfonate] (PTEB) as surfactant for the emulsion polymerization of PEDOT. The reaction involved colloid stabilization and doping in one step, and yielded PEDOT:PTEB composite nanoparticles with high electrical conductivity. Contrary to its counterpart containing nonconductive surfactant, PEDOT: PTEB showed increasing film conductivity with increasing PTEB concentration. The result demonstrates the formation of efficient electrical conduction network formed by the fully conductive latex nanoparticles. The addition of PTEB for EDOT polymerization significantly reduced the size of composite particles, formed stable spherical particles, enhanced thermal stability, crystallinity, and conductivity of PEDOT:PTEB composite. Evidence from UV–VIS and FTIR measurement showed that strong molecular interaction between PTEB and PEDOT resulted in the doping of PEDOT chains. X‐ray analysis further demonstrated that PTEB chains were intercalated in the layered crystal structure of PEDOT. The emulsion polymerization of EDOT using conducting surfactant, PTEB demonstrated the synergistic effect of PTEB on colloid stability and intercalation doping of PEDOT during polymerization resulting in significant conductivity improvement of PEDOT composite nanoparticles. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2536–2548, 2008     

Blue‐light‐emitting polyfluorene functionalized with triphenylamine and cyanophenylfluorene bipolar side chains

A new bipolar conjugated polyfluorene copolymer with triphenylamine and cyanophenylfluorene as side chains, poly{[9,9‐di(triphenylamine)fluorene]‐[9,9‐dihexyl‐fluorene]‐[2,7‐bis(4′‐cyanophenyl)‐9,9′‐spirobifluorene]} ( PTHCF ), was synthesized for studying the polymer backbone emission. Its absolute weight‐average molecular weight was determined as 4.85 × 10⁴ by using gel permeation chromatography with a multiangle light scattering detector. In contrast to the electronic absorption spectrum in dilute solution, the absorbance of PTHCF in thin film was slightly blue shifted. By comparison of the solution and thin‐film photoluminescence (PL) spectra, a red shift of Δλ = 8–9 nm was observed in the thin‐film PL spectrum. The HOMO and LUMO energy levels of the resulting polymer were electrochemically estimated as ?5.68 and ?2.80 eV, respectively. Under the electric‐field intensity of 4.8 × 10⁵ V cm^?1, the obtained hole and electron mobilities were 2.41 × 10^?4 and 1.40 × 10^?4 cm² V^?1 s^?1, respectively. An electroluminescence device with configuration of ITO/PEDOT:PSS/ PTHCF _70%+PBD_30%/CsF/Ca/Al exhibited a deep‐blue emission as a result of excitons formed by the charges migrating along the full‐fluorene main chain. The incorporation of the bipolar side chains into the polymer structure prevented the intermolecular interaction of the fluorene moieties, balance charge injection/transport, and thereby improve the polymer backbone emission. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Structural modulation induced by cobalt-based ionic liquids for enhanced thermoelectric transport in PEDOT:PSS

Poly(3,4ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) has been intensively studied for its thermoelectric applications. Structural modulation to improve crystalline ordering, chain conformation and film morphology is a promising way to decouple the trade-off between conductivity and Seebeck coefficient and thus improve the thermoelectric power factor. Post treatment with ionic liquid ([CoCl₂ ⋅ 6H₂O]:[ChCl]) bearing cobalt-containing anions resulted in a remarkable enhancement of the power factor to 76.8 μW m⁻¹ K⁻². This IL combines the influence of a high-boiling polar organic solvent and diffusing ions. A high σ mainly resulted from the efficient removal of PSS chains, ordering of the structure and delocalization of bipoloran-dominant transport after conformational change. The increase in S was not due to dedoping of PEDOT chains, but rather the sharp feature of the density of states at the Fermi level induced by ion-exchange with unconventional anions.     

Transparent conductive films based on polymer composites containing the mixed‐valence tetrathiafulvalene nanofibers

We report the facile preparation of the conductive polymer composites containing the mixed‐valence tetrathiafulvalene (TTF) nanofibers and their applications as all‐organic transparent conductive materials. TTF can be used as a nanofiller for transforming conventional polymers to conductive materials. Self‐assemble nanofibers of the neutral and radical cation of TTF can be formed in the polymer solutions during the film deposition, and the resulting composite films with several micron thickness can serve as the conductive material with high transparency. Several kinds of conventional polymers, such as polystyrene, poly(methyl methacrylate) (PMMA), and poly(vinylpyrrolidone), can be used as a polymer matrix of the composites. The conductivities of the PMMA film containing 35 mol % of the mixed‐valence TTF and the PEDOT–PSS film showed similar values (2.8 × 10^–2 and 5.4 × 10^–1 S/cm, respectively). In contrast, the normalized transmittance of the PMMA film by 1‐μm thickness greatly increased (96%/μm) when compared with that of the PEDOT–PSS film (10%/μm). In addition, the degradation of the conductivity of the nanofibers by heating and aging was effectively suppressed in the composite samples. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6441–6450, 2009     

Tuning of PEDOT:PSS Properties Through Covalent Surface Modification

Conductive polymer (poly(3,4‐ethylenedioxythiophene)‐poly(styrenesulfonate) (PEDOT:PSS) is an attractive platform for the design of flexible electronic, optoelectronic, and (bio)sensor devices. Practical application of PEDOT:PSS often requires an incorporation of specific molecules or moieties for tailoring of its physical–chemical properties. In this article, a method for covalent modification of PEDOT:PSS using arenediazonium tosylates was proposed. The procedure includes two steps: chemisorption of diazo‐cations on the PEDOT:PSS surface followed by thermal decomposition of the diazonium salt and the covalent bond formation. Structural and surface properties of the samples were evaluated by XPS, SEM‐EDX, AFM, goniometry, and a range of electric and optical measurements. The developed modification procedure enables tuning of the PEDOT:PSS surface properties such as conductivity and optical absorption. The possibility to introduce various organic functional groups (from hydrophilic to hydrophobic) and to create new groups for further functionalization makes the developed procedure multipurpose. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 378–387     

Bismuth Interfacial Doping of Organic Small Molecules for High Performance n‐type Thermoelectric Materials

Development of chemically doped high performance n‐type organic thermoelectric (TE) materials is of vital importance for flexible power generating applications. For the first time, bismuth (Bi) n‐type chemical doping of organic semiconductors is described, enabling high performance TE materials. The Bi interfacial doping of thiophene‐diketopyrrolopyrrole‐based quinoidal (TDPPQ) molecules endows the film with a balanced electrical conductivity of 3.3 S cm^?1 and a Seebeck coefficient of 585 μV K^?1. The newly developed TE material possesses a maximum power factor of 113 μW m^?1 K^?2, which is at the forefront for organic small molecule‐based n‐type TE materials. These studies reveal that fine‐tuning of the heavy metal doping of organic semiconductors opens up a new strategy for exploring high performance organic TE materials.