Structural characterization of radiation‐grafted block copolymer films,using SANS technique

We report small‐angle neutron scattering studies of grafted copolymer films of perfluorinated poly(ethylene propylene), FEP, base polymer and polystyrene, PS, grafted blocks. The films show highly anisotropic scattering patterns, revealing nematic‐like ordering of the crystalline domain structure as a consequence of the processing conditions. Upon grafting, the styrene swells the amorphous domains in the copolymer formation. For styrene content beyond roughly 15%, the amorphous regimes increase on the cost of crystalline domains. To stabilize the rather well‐defined domain structure already given by the original FEP base material, the samples need to be cross‐linked. Without cross‐linking, the nanometer length scale domains vanish, and some large scale structure takes over, likely driven by the immiscibility between FEP and PS. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1660–1668, 2008     

Critical fluctuations and static inhomogeneities in polymer gel volume phase transitions

Thermoresponsive polymer gels exhibit pronounced swelling and deswelling upon changes in temperature, accompanied by dynamic concentration fluctuations that have been interpreted as critical opalescence. These fluctuations span lengthscales similar to that of static structures in the gels, such as the gel polymer‐network meshsize (1–10 nm) and static polymer‐network crosslinking inhomogeneities (10–1000 nm). To systematically investigate this overlay, we use droplet‐based microfluidics and fabricate submillimeter‐sized gel particles with varying static heterogeneity, as revealed on a molecular scale by proton NMR. When these microgels are probed by small‐angle neutron scattering, the detection of dynamic fluctuations during the volume phase transitions is strongly perturbed by the co‐existing static inhomogeneity. Depending of the type of data analysis employed, the temperature‐dependent evolution of the correlation length associated to the dynamic fluctuations does or does not agree with predictions by the critical scaling theory. Only the most homogeneous sample of this study, prepared by controlled polymer crosslinking in droplet microfluidics, shows a diverging correlation length in agreement to the critical scaling theory independent of the specific approach of data analysis. These findings suggest that care must be taken about polymer‐network heterogeneity when gel volume phase transitions are evaluated as critical phenomena. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1112–1122     

Correlating the Morphological Properties and Structural Organization of Monodisperse Spherical Silica Nanoparticles Grown on a Commercial Silica Surface

A variety of nanosilicas have been widely used to fabricate rough surfaces with superhydrophobic and superhydrophilic properties. In this context, we prepared mixed silica and mixed nanosilica that were generated by the growth and self‐assembly of synthesized monodisperse silica nanospheres (11–30 nm, 363 m² g^?1) on the surface of Sylopol‐948 and Dispercoll S3030 by using a base‐catalyzed sol–gel route. Using this process, the interactions and hierarchical structure between the nano‐ and microsized synthesized silica particles were studied by changing the amount of tetraethoxysilane. The resulting materials were characterized by BET analysis, small‐angle X‐ray scattering (SAXS), dynamic light scattering, FTIR spectroscopy, and SEM. The mixed silica presented a higher specific surface area (326 m² g^?1), a six‐fold higher percentage of (SiO)₆ (44–68 %), and a higher amount of silanol groups (14.0–30.7 %) than Sylopol‐948 (271 m² g^?1, 42.6 %, and 12.5 %, respectively). The morphological and hierarchical structural differences in the silica nanoparticles synthesized on the surface of commercial silica (micrometric or nanometric) were identified by SAXS. Mixed micrometric silica exhibited a higher degree of structural organization between particles than mixed nanosilica.     

Structural Characterization of Biomaterials by Means of Small Angle X-rays and Neutron Scattering (SAXS and SANS), and Light Scattering Experiments

Scattering techniques represent non-invasive experimental approaches and powerful tools for the investigation of structure and conformation of biomaterial systems in a wide range of distances, ranging from the nanometric to micrometric scale. More specifically, small-angle X-rays and neutron scattering and light scattering techniques represent well-established experimental techniques for the investigation of the structural properties of biomaterials and, through the use of suitable models, they allow to study and mimic various biological systems under physiologically relevant conditions. They provide the ensemble averaged (and then statistically relevant) information under in situ and operando conditions, and represent useful tools complementary to the various traditional imaging techniques that, on the contrary, reveal more local structural information. Together with the classical structure characterization approaches, we introduce the basic concepts that make it possible to examine inter-particles interactions, and to study the growth processes and conformational changes in nanostructures, which have become increasingly relevant for an accurate understanding and prediction of various mechanisms in the fields of biotechnology and nanotechnology. The upgrade of the various scattering techniques, such as the contrast variation or time resolved experiments, offers unique opportunities to study the nano- and mesoscopic structure and their evolution with time in a way not accessible by other techniques. For this reason, highly performant instruments are installed at most of the facility research centers worldwide. These new insights allow to largely ameliorate the control of (chemico-physical and biologic) processes of complex (bio-)materials at the molecular length scales, and open a full potential for the development and engineering of a variety of nano-scale biomaterials for advanced applications.     

Gelation mechanism and microstructure of organogels formed with various types of gelators

The small‐angle neutron scattering (SANS) and dynamic light scattering (DLS) investigation were carried out for organogels in toluene, formed by organogelators, to elucidate the relationship between the chemical structure and the gelation mechanism as well as the physical properties of the gels. Three different organogelators, that is cyclo(L ‐β‐3,7‐dimethyloctylasparaginyl‐L ‐phenylalanyl) (CPA), trans‐(1R,2R)‐bis(undecylcarbonylamino)cyclohexane (TCH), and N^ε‐lauroyl‐N^α‐stearylaminocarbonyl‐L ‐lysine ethyl ester (LEE), were chosen for comparison. The SANS intensity functions of toluene solutions of these gelators could be reduced with the concentration and were described with a scattering function for thin rods. This indicates that the gels consist of noncorrelated, rod‐like elements aggregated to each other. The characteristic features of the gelation properties, such as the critical gelation concentration, C_gel, the gelation temperature, T_gel, the gel structure, and the gelation mechanism, were different from each other. CPA had the lowest C_gel and became a gel gradually as the temperature decreased, while TCH and LEE had higher C_gels and underwent a sharp sol–gel transition. We conclude that the gelation mechanisms between the CPA and TCH solutions are different. The “CPA type” gelators form a gel by a linear extension of hydrogen‐bonded plane, while the “TCH type” gelators form a twisted wire, because of its strong helicity and crystallizability. In addition, in the latter type, a next generation of fibrils easily stacks on top of the previous ones to form larger fibrils. These models well explain the DLS results and the mechanical properties. That is, the fibrillar stems in CPA gels are rather mobile and fragile, while those in TCH and LEE are frozen and brittle. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3567–3574, 2005     

Small‐Angle Neutron Scattering Studies of Hemoglobin Confined Inside Silica Tubes of Varying Sizes

In addition to the chemical nature of the surface, the dimensions of the confining host exert a significant influence on confined protein structures; this results in immense biological implications, especially those concerning the enzymatic activities of the protein. This study probes the structure of hemoglobin (Hb), a model protein, confined inside silica tubes with pore diameters that vary by one order of magnitude (≈20–200 nm). The effect of confinement on the protein structure is probed by comparison with the structure of the protein in solution. Small‐angle neutron scattering (SANS), which provides information on protein tertiary and quaternary structures, is employed to study the influence of the tube pore diameter on the structure and configuration of the confined protein in detail. Confinement significantly influences the structural stability of Hb and the structure depends on the Si‐tube pore diameter. The high radius of gyration (R_g) and polydispersity of Hb in the 20 nm diameter Si‐tube indicates that Hb undergoes a significant amount of aggregation. However, for Si‐tube diameters greater or equal to 100 nm, the R_g of Hb is found to be in very close proximity to that obtained from the protein data bank (PDB) reported structure (R_g of native Hb=23.8 Å). This strongly indicates that the protein has a preference for the more native‐like non‐aggregated state if confined inside tubes of diameter greater or equal to 100 nm. Further insight into the Hb structure is obtained from the distance distribution function, p(r), and ab initio models calculated from the SANS patterns. These also suggest that the Si‐tube size is a key parameter for protein stability and structure.     

Counterion Association and Structural Conformation Change of Charged PAMAM Dendrimer in Aqueous Solutions Revealed by Small Angle Neutron Scattering

Our previous study of the structure change of poly(amidoamine) starburst dendrimers (PAMAM) dendrimer of generation 5 (G5) have demonstrated that although the overall molecular size is practically unaffected by increasing DCl concentration, a configurational transformation, from a diffusive density profile to a more uniform density distribution, is clearly observed. In the current paper, the focus is placed on understanding the effect of counterion identity on the inter-molecular structure and the conformational properties by studying the effect due to DBr using small angle neutron scattering (SANS) and integral equation theory. While the overall molecular size is found to be essentially unaffected by the change in the pD of solutions, it is surprising that the intra-molecular configurational transformation is not observed when DBr is used. The overall effective charge of a dendrimer is nearly the same for α < 1, independent of the type of acids. However, when α > 1, the effect of counterion identity becomes significant, the effective charge carried by a charged G5 PAPAM protonated by DBr becomes smaller than that of solutions with DCl. As a consequence, a counterion identity dependence of counterion association is revealed: Under the same level of molecular protonation, the specific counterion association, which is defined as the ratio of bound chloride anions to positively charged amines per molecule, is larger for the G5 PAMAM dendrimer charged by DBr than the one by DCl.     

Synthesis and properties of a deuterated phenolic resin

A highly deuterated novolac‐type phenolic resin was prepared by polycondensation of deuterated phenol and formaldehyde using oxalic acid as an acid catalyst. The polycondensation of deuterated monomers and the formation of the highly deuterated phenolic resin were confirmed by the gel permeation chromatography, IR, and ¹H NMR analyses. With the exception of hydroxyl groups, the degree of deuteration was estimated to be more than 98%. The polymer conformation in THF solution was evaluated by the scaling exponent of the Mark–Houwink–Sakurada equation. The exponent of the deuterated phenolic resin is 0.26 in THF at 40 °C and is close to that of a nondeuterated phenolic resin, which suggests that phenolic resins behave like a compact sphere irrespective of deuteration. The curing behavior of the deuterated phenolic resin with hexamethylenetetramine was confirmed by differential scanning calorimetry analysis. The cured highly deuterated phenolic resin exhibits a lower incoherent neutron scattering background than that of the nondeuterated phenolic resin, which suggests that the former is suitable for matrix resins with low incoherent backgrounds for small‐angle neutron scattering studies of thermosetting resins. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

A Systematic Study of Peripherally Multiple Aromatic Ester‐Functionalized Poly(benzyl ether) Dendrons for the Fabrication of Organogels: Structure–Property Relationships and Thixotropic Property

A new class of peripherally multiple aromatic ester‐functionalized poly(benzyl ether) dendrons and/or dendrimers with different focal point substituents, surface groups, interior structures, as well as different generations have been synthesized and their structure–property relationships with respect to their gelation ability have been investigated systematically. Most of these dendrons are able to gel organic solvents over a wide polarity range. Evident dendritic effects were observed not only in gelation capability but also in thermotropic, morphological, and rheological characterizations. It was disclosed that subtle changes in peripheral ester functionalities and interior dendritic structures affected the gelation behavior of the dendrons significantly. Among all the dendrons studied, the second‐ and third‐generation dendrons G₀G₂‐Me and G₀G₃‐Me with dimethyl isophthalates (DMIP) as peripheral groups exhibited the best capability in gelation, and stable gels were formed in more than 22 aromatic and polar organic solvents. The lowest critical gelation concentration (CGC) reached 2.0 mg mL^?1, indicating that approximately 1.35×10⁴ solvent molecules could be entrapped by one dendritic molecule. Further study on driving forces in gel formation was carried out by using a combination of single‐crystal/powder X‐ray diffraction (XRD) analysis and concentration‐dependent (CD)/temperature‐dependent (TD) ¹H NMR spectroscopy. The results obtained from these experiments revealed that the multiple π–π stacking of extended π‐systems due to the peripheral DMIP rings, cooperatively assisted by non‐conventional hydrogen‐bonding, is the key contributor in the formation of the highly ordered supramolecular and fibrillar network. In addition, these dendritic organogels exhibited unexpected thixotropic‐responsive properties, which make them promising candidates with potential applications in the field of intelligent soft materials.     

Apolar Bimesogens and the Incidence of the Twist–Bend Nematic Phase

The nematic twist–bend phase (N_TB) was, until recently, only observed for polar mesogenic dimers, trimers or bent‐core compounds. In this article, we report a comprehensive study on novel apolar materials that also exhibit N_TB phases. The N_TB phase was observed for materials containing phenyl, cyclohexyl or bicyclooctyl rings in their rigid‐core units. However, for materials with long (>C7) terminal chains or mesogenic core units comprising three ring units, the N_TB phase was not observed and instead the materials exhibited smectic phases. One compound was found to exhibit a transition from the N_TB phase to an anticlinic smectic C phase; this is the first example of this polymorphism. Incorporation of lateral substitution with respect to the central core unit led to reductions in transition temperatures; however, the N_TB phase was still found to occur. Conversely, utilising branched terminal groups rendered the materials non‐mesogenic. Overall, it appears that it is the gross molecular topology that drives the incidence of the N_TB phase rather than simple dipolar considerations. Furthermore, dimers lacking any polar groups, which were prepared to test this hypothesis, were found to be non mesogenic, indicating that at the extremes of polarity these effects can dominate over topology.     

Small‐angle neutron scattering analysis of bottlebrush backbone and side chain flexibility

Bottlebrush polymers have densely tethered side chains grafted to a linear polymer backbone, resulting in stretching of both the side chains and backbone. Prior studies have reported that the side chains are only weakly stretched while the backbone is highly elongated. Here, scaling laws for the bottlebrush backbone and side chains are determined through small‐angle neutron scattering analysis of a systematic series of poly(lactic acid) bottlebrush polymers synthesized via a “grafting‐through” ring‐opening polymerization. Scattering profiles are modeled with the empirical Guinier–Porod, rigid cylinder, and flexible cylinder models. Side chains are found to be only weakly stretched, with an end‐to‐end distance proportional to N^0.55, while the overall bottlebrush increases in size proportional to N^0.77. These results demonstrate that the bottlebrush backbone is not fully extended and that both side chains and backbone have significant conformational flexibility in solution. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 104–111     

Development of nanostructure in resistant starch type III during thermal treatments and cycling

The effect of recrystallization temperature on the lamellar structure of RSIII samples was studied using XRD and SAXS. The polymorph type could be manipulated in a controlled manner, independently of the plant source. In RSIII from corn starch and from high-amylose corn starch, retrogradation at a low temperature led to the formation of polymorph B with lamellas arranged in long-range periodicity, whereas retrogradation at a high temperature led to the formation of polymorphs A and V with no defined periodicity. The retrogradation temperature of wheat starch did not have a major effect on its nanostructure. For both polymorphs, the enzymatic degradation decreased as the degree of order within the crystal increased.     

Kinetics of Collapse Transition and Cluster Formation in a Thermoresponsive Micellar Solution of P(S‐b‐NIPAM‐b‐S) Induced by a Temperature Jump

Structural changes at the intra‐ as well as intermicellar level were induced by the LCST‐type collapse transition of poly(N‐isopropyl acrylamide) in ABA triblock copolymer micelles in water. The distinct process kinetics was followed in situ and in real‐time using time‐resolved small‐angle neutron scattering (SANS), while a micellar solution of a triblock copolymer, consisting of two short deuterated polystyrene endblocks and a long thermoresponsive poly(N‐isopropyl acrylamide) middle block, was heated rapidly above its cloud point. A very fast collapse together with a multistep aggregation behavior is observed. The findings of the transition occurring at several size and time levels may have implications for the design and application of such thermoresponsive self‐assembled systems.     

Morphology of side chain liquid crystalline block copolymer thin films and effects of thermal annealing

The self-assembly behavior of siloxane based side chain liquid crystalline block copolymer thin films are investigated via grazing incidence small angle X-ray scattering and atomic force microscopy. The as-spun films displayed polystyrene cylinders perpendicular to the substrate and the cylinders reoriented parallel to the surface after thermal annealing. The morphology observed in the as-spun films is resultant from the orientation of the smectic LC mesophase relative to the substrate. Annealing above both the polystyrene glass transition temperature and the smectic to isotropic transition temperature eliminates the influence of the LC phase, leading to a reorientation of the morphology that minimizes the interfacial energy of the system. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3263–3266, 2007     

Synthesis,characterization, and ion‐complexing properties of polymers displaying densely packed arrays of crown‐ethers as lateral substituents

We report the synthesis and ion‐binding properties of four poly(crown‐ethers) displaying either one or two crown‐ethers (15‐crown‐5 or 18‐crown‐6) on every third carbon alongside the backbone. The polymers were synthesized by living anionic ring‐opening polymerization of disubstituted cyclopropane‐1,1‐dicarboxylates monomers. Cation binding of the polychelating polymers and corresponding monomers to Na⁺ and K⁺ was evaluated by picrate extraction and isothermal calorimetry titration. This novel family of poly(crown‐ethers) demonstrated excellent initial binding of the alkali ions to the polymers, with a higher selectivity for potassium. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2337–2345     

Structure–Property Investigations of Substituted Triarylamines and Their Applications as Fluorescent pH Sensors

Fourteen triphenylamine derivatives functionalized with fluorophenyl, methoxyphenyl, and pyridinyl groups as respective donors and acceptors were synthesized and characterized. Their photophysical properties were systematically investigated in various solvents with different polarities. The solvent‐dependent Stokes shifts of these compounds were observed and analyzed by the Lippert–Mataga equation. The synthesized compounds, especially tris(4‐(pyridin‐4‐yl)phenyl) amine, presented pH‐dependent absorptions and emissions, indicating that these compounds might be used as pH sensors.