Diketopyrrolopyrrole‐based conjugated polymers and small molecules for organic ambipolar transistors and solar cells

The present highlight discusses major work in the synthesis of low bandgap diketopyrrolopyrrole ( DPP )‐based polymers with donor–acceptor–donor ( D–A–D ) approach and their application in organic electronics. It examines the past and recent significant advances which have led to development of low bandgap DPP ‐based materials with phenyl and thiophene as donors. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 4241–4260     

Synthesis and characterization of thiazolothiazole‐based polymers and their applications in polymer solar cells

A novel series of thiazolothiazole (Tz)‐based copolymers, poly[9,9‐didecylfluorene‐2,7‐diyl‐alt‐2,5‐bis‐(3‐hexylthiophene‐2‐yl)thiazolo[5,4‐d]thiazole] (P1), poly[9,9‐dioctyldibenzosilole‐2,7‐diyl‐alt‐2,5‐bis‐(3‐hexylthiophene‐2‐yl)thiazolo[5,4‐d]thiazole] (P2), and poly[4,4′‐bis(2‐ethylhexyl)‐dithieno[3,2‐b:2′,3′‐d]silole‐alt‐2,5‐bis‐(3‐hexylthiophene‐2‐yl)thiazolo[5,4‐d]thiazole] (P3), were synthesized for the use as donor materials in polymer solar cells (PSCs). The field‐effect carrier mobilities and the optical, electrochemical, and photovoltaic properties of the copolymers were investigated. The results suggest that the donor units in the copolymers significantly influenced the band gap, electronic energy levels, carrier mobilities, and photovoltaic properties of the copolymers. The band gaps of the copolymers were in the range of 1.80–2.14 eV. Under optimized conditions, the Tz‐based polymers showed power conversion efficiencies (PCEs) for the PSCs in the range of 2.23–2.75% under AM 1.5 illumination (100 mW/cm²). Among the three copolymers, P1, which contained a fluorene donor unit, showed a PCE of 2.75% with a short‐circuit current of 8.12 mA/cm², open circuit voltage of 0.86 V, and a fill factor (FF) of 0.39, under AM 1.5 illumination (100 mW/cm²). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Photodegradation of C‐PCPDTBT and Si‐PCPDTBT: Influence of the Bridging Atom on the Stability of a Low‐Band‐Gap Polymer for Solar Cell Application

The kinetics of photodegradation and the reactivity of different sites of the low‐band‐gap polymers poly[2,6‐(4,4‐bis‐(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b:3,4‐b′]dithiophene)‐alt‐4,7‐(2,1,3‐benzothiadiazole)] (C‐PCPDTBT) and poly[2,6‐(4,4‐bis‐(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]silole)‐alt‐4,7‐(2,1,3‐benzothiadiazole)] (Si‐PCPDTBT) are investigated as thin films and are compared to those of poly(3‐hexylthiophene) (P3HT). The decay kinetics are monitored with UV/Vis spectroscopy and the reactivity and product evolution are investigated with X‐ray photoelectron spectroscopy (XPS). Both polymers exhibit higher stability than P3HT. The bridging atom in the cyclopentadithiophene (CPDT) subunit has a significant influence on the stability. Varying oxidation rates for the different elements were observed. In the case of Si‐PCPDTBT, the silicon atom is oxidized primarily, whereas the photooxidation rates of the other elements are reduced relative to C‐PCPDTBT. Additionally, XPS experiments with varying excitation energies reveal a significant reaction gradient within a few nanometers of the surface of degraded thin films of C‐PCPDTBT.     

Synthesis and properties of fluorene‐based polyheteroarylenes for photovoltaic devices

Novel copolymers consisting of the alternating push–pull comonomers fluorene and thieno[3,4‐b]pyrazine/quinoxaline were synthesized by a palladium‐catalyzed Suzuki cross‐coupling reaction in 60–80% yields. The structure of the deeply colored copolymers was confirmed with ¹H and ¹³C NMR. All the new materials were characterized with spectroscopic and electrochemical methods. Bulk heterojunction organic solar cells based on some of the novel polymers in combination with the well‐known fullerene acceptor [6,6]‐phenyl C₆₁–butyric acid methyl ester were fabricated, and their photovoltaic parameters were measured. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6952–6961, 2006     

Low band‐gap modulation of isoindigo‐based copolymers toward high open‐circuit voltage of polymer solar cells

Designing low band‐gap‐conjugated polymers coupled with low HOMO levels attracts great attention in the field of polymer solar cells (PSCs). By using donor–acceptor (D‐A) copolymerization strategy, we designed and synthesized a series of low band‐gap copolymers with deep HOMO levels via introducing an isoindigo (IID) acceptor unit in the copolymers with the donor unit of fluorene (F) (PIID‐F), carbazole (Cz) (PIID‐Cz), thiophene (Th) (PIID‐Th), dithiophene (DTh) (PIID‐DTh), or dithienosilole (DTS) (PIID‐DTS). The HOMO level of the copolymers, measured by electrochemical cyclic voltammetry, varies from ?5.3 eV to ?5.8 eV, depending on different donor units in the copolymers. However, the LUMO levels of all the copolymers are fixed at about ?3.6 eV, which is mainly determined by IID acceptor unit due to its strong electron‐withdrawing ability. The new results will provide an effect help in designing IID based molecular structures. Among the copolymers, PIID‐DTS has a low band gap of 1.58 eV and possesses a low‐lying HOMO energy level of ?5.33 eV. The PSCs based on PIID‐DTS as donor and PC₇₀BM as acceptor exhibited a high open‐circuit voltage (V_oc) of 0.93 V and a primary power conversion efficiency of 2.45%. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3477–3485     

Side chain engineering of naphthalene diimide–bithiophene‐based polymer acceptors in all‐polymer solar cells

Two novel polymeric acceptors based on naphthalene diimide (NDI) and 2.2′‐bithiophene, named as P(NDI2THD‐T2) and P(NDI2TOD‐T2), were designed and synthesized for all polymer solar cells application. The structural and electronic properties of the two acceptors were modulated through side‐chain engineering of the NDI units. The optoelectronic properties of the polymers and the morphologies of the blend films composed of the polymer acceptors and a donor polymer PTB7‐Th were systemically investigated. With thiophene groups introduced into the side chains of the NDI units, both polymers showed wider absorption from 350 nm to 900 nm, compared with the reference polymer acceptor of N2200. No redshift of absorption spectra from solutions to films indicated reduced aggregation of the polymers due to the steric hindrance effect of thiophene rings in the side chains. The photovoltaic performance were characterized for devices in a configuration of ITO/PEDOT:PSS/PTB7‐Th:acceptors/2,9‐bis(3‐(dimethylamino)propyl)anthra[2,1,9‐def:6,5,10‐def]diisoquinoline‐1,3,8,10(2H,9H)‐tetraone (PDIN)/Al. With the addition of diphenyl ether as an additive, the power conversion efficiencies (PCEs) of 2.73% and 4.75% for P(NDI2THD‐T2) and P(NDI2TOD‐T2) based devices were achieved, respectively. The latter showed improved J_sc, Fill Factor (FF), and PCE compared with N2200 based devices. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3679–3689     

Synthesis and characterization of new selenophene‐based conjugated polymers for organic photovoltaic cells

Three new polymers poly(3,4′′′‐didodecyl) hexaselenophene) (P6S), poly(5,5′‐bis(4,4′‐didodecyl‐2,2′‐biselenophene‐5‐yl)‐2,2′‐biselenophene) (HHP6S), and poly(5,5′‐bis(3′,4‐didodecyl‐2,2′‐biselenophene‐5‐yl)‐2,2′‐biselenophene) (TTP6S) that have the same selenophene‐based polymer backbone but different side chain patterns were designed and synthesized. The weight‐averaged molecular weights (M_w) of P6S, HHP6S, and TTP6S were found to be 19,100, 24,100, and 19,700 with polydispersity indices of 2.77, 1.48, and 1.41, respectively. The UV–visible absorption maxima of P6S, HHP6S, and TTP6S are at 524, 489, and 513 nm, respectively, in solution and at 569, 517, and 606 nm, respectively, in the film state. The polymers P6S, HHP6S, and TTP6S exhibit low band gaps of 1.74, 1.95, and 1.58 eV, respectively. The field‐effect mobilities of P6S, HHP6S, and TTP6S were measured to be 1.3 × 10^?4, 3.9 × 10^?6, and 3.2 × 10^?4 cm² V^?1 s^?1, respectively. A photovoltaic device with a TTP6S/[6,6]‐phenyl C₇₁‐butyric acid methyl ester (1:3, w/w) blend film active layer was found to exhibit an open circuit voltage (V_OC) of 0.71 V, a short circuit current (J_SC) of 5.72 mA cm^?2, a fill factor of 0.41, and a power conversion efficiency (PCE) of 1.67% under AM 1.5 G (100 mW cm^?2) illumination. TTP6S has the most planar backbone of the tested polymers, which results in strong π–π interchain interactions and strong aggregation, leading to broad absorption, high mobility, a low band gap, and the highest PCE. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Imide‐functionalized naphthodithiophene based donor‐acceptor conjugated polymers for solar cells

Donor‐acceptor conjugated polymers containing a new imide‐functionalized naphthodithiophene (INDT) as the acceptor unit and a 2,2'‐bithiophene with varied substituents as the donor unit have been synthesized. The bandgaps of these polymers depend strongly on the dihedral angle of the 2,2'‐bithiophene unit. The 3,3'‐dialkoxy substitution (polymers PDOR / PBOR ) leads to near planar bithiophene conformation due to the well‐known S–O short contact, while the 3,3'‐dialkyl substitution (polymer PDR ) results in significant twisting due to the steric effect. Consequently PDOR / PBOR shows the lowest bandgap of 1.82/1.85 eV while PDR has a bandgap of 2.38 eV. Bulk‐heterojunction solar cells of the polymer/fullerene blends have been fabricated. Preliminary results show that PBOR gives the best device performance with power conversion efficiencies as high as 2.45% in air without any thermal annealing treatment, indicating the promising potential of INDT‐containing conjugated polymers for efficient solar cells. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3818–3828     

Syntheses and characterization of carbazole based new low‐band gap copolymers containing highly soluble benzimidazole derivatives for solar cell application

Newly designed 2H‐benzimidazole derivatives which have solubility groups at 2‐position have been synthesized and incorporated into two highly soluble carbazole based alternating copolymers, poly[2,7‐(9‐(1′‐octylnonyl)‐9H‐carbazole)‐alt‐5,5‐(4′,7′‐di(thien‐2‐yl)‐2H‐benzimidazole‐2′‐spirocyclohexane)] (PCDTCHBI) and poly[2,7‐(9‐(1′‐octylnonyl)‐9H‐carbazole)‐alt‐5,5‐(4′,7′‐di(thien‐2‐yl)‐2H‐benzimidazole‐2′‐spiro‐4′′‐((2′′′‐ethylhexyl)oxy)‐cyclohexane)] (PCDTEHOCHBI) for photovoltaic application. These alternating copolymers show low‐band gap properties caused by internal charge transfer from an electron‐rich unit to an electron‐deficient moiety. HOMO and LUMO levels are –5.53 and –3.86 eV for PCDTCHBI, and –5.49 and –3.84 eV for PCDTEHOCHBI, respectively. Optical band gaps of PCDTCHBI and PCDTEHOCHBI are 1.67 and 1.65 eV, respectively. The new carbazole based the 2H‐benzimidazole polymers show 0.11–0.13 eV lower values of band gaps as compared to that of carbazole based benzothiadiazole polymer, poly[N‐9′‐heptadecanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)] (PCDTBT), while keeping nearly the same deep HOMO levels. The power conversion efficiencies of PCDTCHBI and PCDTEHOCHBI blended with [6,6]phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) are 1.03 and 1.15%, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Decreased domain size and improved crystallinity by adjusting solvent–polymer interaction parameters in all‐polymer solar cells

We have investigated the effect of solvent–polymer interaction on the morphology, crystallinity, and device performance of poly‐(3‐hexylthiophene) (P3HT) and poly{2,7‐(9,9‐didodecyl‐fluorene)‐alt‐5,5‐[4′,7′‐bis(2‐thienyl)‐2′,1′,3′‐benzothia‐diaole]} (PF12TBT) blend system. 3‐Hexylthiophene (3‐HT), which had the similar structural units with both donor and acceptor materials, was chosen as the solvent additive to be added into the main solvent chlorobenzene (CB), to adjust the solvent–polymer interaction. With the 3‐HT percentage increasing from 5 to 30% in CB solution, the solvent–polymer interaction between polymer and solvent molecules decreased slightly according to the calculated solubility parameters (δ) and interaction parameters (χ₁₂). As a result, nanoscale phase‐separated and interconnected morphology with decreased domain size of both donor and acceptor was formed. Meanwhile, the order of P3HT molecule was enhanced which resulted from the extended film drying time and increased molecular planarity after incorporation of 3‐HT. The power conversion efficiency (PCE) had a gradual improvement to 1.08% as the 3‐HT percentage reached 10%, which can be attributed to the enhanced short‐circuit current (J_sc) and fill factor (FF). However, when the 3‐HT percentage exceeded 20%, the decreased J_sc and FF ultimately decreased the PCE. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 288–296     

Crystalline and active additive for optimization morphology and absorption of narrow bandgap polymer solar cells

The morphology of active layer with an interpenetrating network structure and appropriate phase separation is of great significance to improve the photovoltaic performance for polymer solar cells. A highly crystalline small molecule named DPP-TP6 was synthesized and incorporated into the narrow bandgap polymer solar cells to optimize the morphology of PTB7:PC₇₁BM active layer. The DPP-TP6 small molecule was demonstrated to enhance the light absorbance of active layer and play the role of energy cascade to increase the exciton separation and charge transfer. What's more, DPP-TP6 facilitated forming interpenetrating network structure and increasing the phase separation size of ternary blends. These phenomena lead to a higher hole mobility and a more balanced carrier mobility, so as to increase the power conversion efficiency to 7.85% at DPP-TP6 weight ratio of 8 wt %, comparing to the pristine PTB7:PC₇₁BM system of 6.50%. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 726–733     

Acceptor–acceptor conjugated copolymers based on perylenediimide and benzothiadiazole for all‐polymer solar cells

Donor–acceptor (D–A) conjugated copolymers are one of known classes of organic optoelectronic materials and have been well developed. However, less attention has been paid on acceptor–acceptor (A–A) conjugated analogs. In this work, two types of A–A conjugated copolymers, namely P1‐Cn and P2‐Cn (n is the carbon number of their alkyl side chains), were designed and synthesized based on perylenediimide ( PDI ) and 2,1,3‐benzothiadiazole ( BT ). Different from P1‐Cn , P2‐Cn polymers have additional acetylene π‐spacers between PDI and BT and thus hold a more planar backbone configuration. Property studies revealed that P2‐Cn polymers possess a much red‐extended UV–vis absorption spectrum, stronger π–π interchain interactions, and one‐order larger electron mobility in their neat film state than P1‐Cn . However, all‐polymer solar cells using P1‐Cn as acceptor component and poly(3‐hexyl thiophene) or poly(2,7‐(9,9‐didodecyl‐fluoene)‐alt?5,5′‐(4,7‐dithienyl‐2‐yl‐2,1,3‐benzothiadiazole) as donor component exhibited much better performance than those based on P2‐Cn . Apart from their backbone chemical structure, the side chains were found to have little influence on the photophysical, electrochemical, and photovoltaic properties for both P1‐Cn and P2‐Cn polymers. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1200–1215     

Stabilization of the film morphology in polymer: Fullerene heterojunction solar cells with photocrosslinkable bromine‐functionalized low‐bandgap copolymers

Novel bromine‐functionalized photocrosslinkable low‐bandgap copolymers, PBDTTT‐Br25 and PBDTTT‐Br50, are synthesized via Stille cross‐coupling polymerization for the purpose of stabilizing the film morphology in polymer solar cells (PSCs). Photocrosslinking of PBDTTT‐Br25 and PBDTTT‐Br50 copolymers dramatically improves the solvent resistance of the active layer without disrupting the molecular ordering and charge transport, which is confirmed by the insolubility of the films washed by organic solvents and by their thermal behavior. As a result, the formation of large aggregations of fullerene is suppressed in polymer:fullerene blend films even after prolonged thermal annealing, and the stability of the device is enhanced when compared with cells based on noncrosslinkable PBDTTT. The power conversion efficiency of the PSCs based on PBDTTT‐Br25 and PBDTTT‐Br50 reaches 5.17% and 4.48%, respectively, which is improved obviously in comparison with that (4.26%) of the PSCs based on the control polymer PBDTTT. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3123–3131     

Influence of 4‐fluorophenyl pendants in thieno[3,4‐b]thiophene‐benzo[1,2‐b:4,5‐b′]dithiophene‐based polymers on the performance of photovoltaics

Polymers consisting of benzo[1,2‐b:4,5‐b′]dithiophene and thieno[3,4‐b]thiophene units (PTB‐based polymers), either fully or partially containing 4‐fluorophenyl pendants, are synthesized as electron donor materials for inverted‐type polymer solar cells (PSCs). The influence of the 4‐fluorophenyl pendant content on the thermal and optical properties, the highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO), the hole mobilities, and photovoltaic performances are investigated. As the 4‐fluorophenyl pendant content increased, the HOMO and LUMO of the polymers were deepened proportionally and the open‐circuit voltages of the PSCs improved. Incorporation of 4‐fluorophenyl pendants into the polymers also affected the crystallinity, orientation, and compatibility with [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester in the active layers, leading to nonlinearities in the short‐circuit current densities, and fill factors. The incorporation of an appropriate number of 4‐fluorophenyl pendants enhanced the power conversion efficiencies of the PSC devices from 2.25 to 3.96% for identical device configurations. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1586–1593     

Naphtho[2,1‐b:3,4‐b′]dithiophene‐based Bulk Heterojunction Solar Cells: How Molecular Structure Influences Nanoscale Morphology and Photovoltaic Properties

Organic bulk heterojunction photovoltaic devices based on a series of three naphtho[2,1‐b:3,4‐b′]dithiophene (NDT) derivatives blended with phenyl‐C₇₁‐butyric acid methyl ester were studied. These three derivatives, which have NDT units with various thiophene‐chain lengths, were employed as the donor polymers. The influence of their molecular structures on the correlation between their solar‐cell performances and their degree of crystallization was assessed. The grazing‐incidence angle X‐ray diffraction and atomic force microscopy results showed that the three derivatives exhibit three distinct nanoscale morphologies. We correlated these morphologies with the device physics by determining the J–V characteristics and the hole and electron mobilities of the devices. On the basis of our results, we propose new rules for the design of future generations of NDT‐based polymers for use in bulk heterojunction solar cells.     

Pyrrolo[3,4‐c]pyrrole‐1,3‐dione‐based large band gap polymers containing benzodithiophene derivatives for highly efficient simple structured polymer solar cells

Pyrrolo[3,4‐c]pyrrole‐1,3(2H,5H)‐dione (DPPD)‐based large band gap polymers, P(BDT‐TDPPDT) and P(BDTT‐TDPPDT), are prepared by copolymerizing electron‐rich 4,8‐bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene (BDT) or 4,8‐bis(5‐(2‐ethylhexyl)thiophen‐2‐yl)benzo[1,2‐b:4,5‐b′]dithiophene (BDTT) unit with novel electron deficient 2,5‐dioctyl‐4,6‐di(thiophen‐2‐yl)pyrrolo[3,4‐c]pyrrole‐1,3(2H,5H)‐dione (TDPPDT) unit. The absorption bands of polymers P(BDT‐TDPPDT) and P(BDTT‐TDPPDT) cover the region from 300 to 600 nm with an optical band gap of 2.11 eV and 2.04 eV, respectively. The electrochemical study illustrates that the highest occupied/lowest unoccupied molecular orbital energy levels of P(BDT‐TDPPDT) and P(BDTT‐TDPPDT) are ?5.39 eV/?3.28 eV and ?5.44 eV/?3.40 eV, respectively. The single layer polymer solar cell (PSC) fabricated with a device structure of ITO/PEDOT:PSS/P(BDT‐TDPPDT) or P(BDTT‐TDPPDT):PC70BM+DIO/Al offers a maximum power conversion efficiency (PCE) of 6.74% and 6.57%, respectively. The high photovoltaic parameters such as fill factor (～72%), open circuit voltage (V_oc, ～0.90 V), incident photon to collected electron efficiency (～76%), and PCE obtained for the PSCs made from polymers P(BDT‐TDPPDT) and P(BDTT‐TDPPDT) make them as promising large band gap polymeric candidates for PSC application. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3564–3574     

Synthesis and properties of mono‐ and di‐fluoro‐substituted 2,3‐didodecylquinoxaline‐based polymers for polymer solar cells

We synthesized two new alternating polymers, namely P(Tt‐FQx) and P(Tt‐DFQx) , incorporating electron rich tri‐thiophene and electron deficient 6‐fluoroquinoxaline or 6,7‐difluoroquinoxaline derivatives. Both polymers P(Tt‐FQx) and P(Tt‐DFQx) exhibited high thermal stabilities and the estimated 5% weight loss temperatures are 425 and 460 °C, respectively. Polymers P(Tt‐FQx) and P(Tt‐DFQx) displayed intense absorption band between 450 and 700 nm with an optical band gap (E_g) of 1.78 and 1.80 eV, respectively. The determined highest occupied/lowest unoccupied molecular orbital's (HOMO/LUMO) of P(Tt‐DFQx) (?5.48 eV/?3.68 eV) are slightly deeper than those of P(Tt‐FQx) ( ?5.32 eV/?3.54 eV). The polymer solar cells fabricated with a device structure of ITO/PEDOT:PSS/ P(Tt‐FQx) or P(Tt‐DFQx) :PC₇₀BM (1:1.5 wt %) + 3 vol % DIO/Al offered a maximum power conversion efficiency (PCE) of 3.65% with an open‐circuit voltage (V_oc) of 0.59 V, a short‐circuit current (J_sc) of 10.65 mA/cm² and fill factor (FF) of 59% for P(Tt‐FQx) ‐based device and a PCE of 4.36% with an V_oc of 0.69 V, a J_sc of 9.92 mA/cm², and FF of 63% for P(Tt‐DFQx) ‐based device. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 545–552     

Synthesis,characterization, and application to polymer solar cells of polythiophene derivatives with ester‐ or ketone‐substituted phenyl side groups

Four polythiophene derivatives including regiorandom polymers P1 , P2 , and P3 and a regioregular polymer P4 , containing a phenyl side chain with electron‐withdrawing carbonyl groups such as an ester and a ketone at the 3‐position of the thiophene ring, were synthesized by Stille coupling reaction. Bulk‐heterojunction polymer solar cells (PSCs) based on these polymers as p‐type semiconductors and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) were fabricated, and their photovoltaic performances were evaluated for the first time. The PSC devices based on the regioregular polymer P4 :PCBM = 1:2 (w/w) exhibited a high‐open‐circuit voltage (V_oc) of 0.943 V because of the low‐lying highest occupied molecular orbit energy level of P4 . The short π–π stacking distance (0.355 nm) in the parallel direction to the substrate and “face‐on” rich orientation were observed by the grazing incidence wide‐angle X‐ray scattering experiment, which might reflect higher J_sc and FF values of the P4 :[6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) PSC device than others. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 875–887