Comparison of water isotope-ratio determinations using two cavity ring-down instruments and classical mass spectrometry in continuous ice-core analysis

We present a detailed comparison between subsequent versions of commercially available wavelength-scanned cavity ring-down water isotope analysers (L2120-i and L2130-i, Picarro Inc.). The analysers are used in parallel in a continuous mode by adaption of a low-volume flash evaporation module. Application of the analysers to ice-core analysis is assessed by comparison between continuous water isotope measurements of a glacial ice-core from Severnaya Zemlya with discrete isotope-ratio mass spectrometry measurements performed on parallel samples from the same ice-core. The great advances between instrument versions, particularly in the measurement of δ²H, allow the continuous technique to achieve the same high level of accuracy and precision obtained using traditional isotope spectrometry techniques in a fraction of the experiment time. However, when applied to continuous ice-core measurements, increased integration times result in a compromise of the achievable depth resolution of the ice-core records.     

AgF desalination procedure for the routine determination of oxygen and hydrogen isotopic composition of saline waters and brines

The routine methods for stable oxygen and hydrogen isotope analysis of water involve water–CO₂ gas equilibration and water reduction on hot metal (e.g. Zn, Cr, U) and subsequent mass spectrometric analysis of the evolved gases of CO₂ and H₂ for ¹⁸O/¹⁶O and ²H/¹H ratios, respectively. Precise determination of the isotopic composition of water in brines with application of these standard methods is still problematic and technically often impossible due to detrimental influence of dissolved salts. The new method of brine desalination presented in this study overcomes the problem of the isotope salt effects encountered during the application of the routine techniques for the determination of the isotopic composition of high saline waters. The procedure combines two technical steps: (i) the chemical precipitation of Mg and Ca ions as insoluble non-hydroscopic fluorides, and (ii) the vacuum distillation of water from solution–precipitate mixture. The application of simple vacuum distillation allows full extraction of water and dehydration of remaining salts in a temperature range from 300 to 350?°C without hydrogen and oxygen isotope fractionation. The precision and accuracy of δ¹⁸O and δ²H determination of saline waters and brines with prior application of AgF desalination procedure is comparable with that usually obtained for fresh waters.     

Isotopic composition of bottled water in Saudi Arabia

The ¹⁸O/¹⁶O and ²H/¹H ratios of 18 water brands representing the most popular bottled water brands in the Saudi market were measured using a system based on the latest advancements in tunable off-axis integrated cavity output diode laser spectroscopy (OA-ICOS) in the near-infrared spectral region. Utilizing δ¹⁸O and the δ²H values of locally produced water samples, a meteoric water line (δ²H?=?7.84 δ¹⁸O?+?2.11) was extracted and found to be consistent with the slope of the global meteoric water line (GMWL) and the geographic location of Saudi Arabia.     

Isotopic composition of atmospheric moisture from pan water evaporation measurements

A continuous and reliable time series data of the stable isotopic composition of atmospheric moisture is an important requirement for the wider applicability of isotope mass balance methods in atmospheric and water balance studies. This requires routine sampling of atmospheric moisture by an appropriate technique and analysis of moisture for its isotopic composition. We have, therefore, used a much simpler method based on an isotope mass balance approach to derive the isotopic composition of atmospheric moisture using a class-A drying evaporation pan. We have carried out the study by collecting water samples from a class-A drying evaporation pan and also by collecting atmospheric moisture using the cryogenic trap method at the National Institute of Hydrology, Roorkee, India, during a pre-monsoon period. We compared the isotopic composition of atmospheric moisture obtained by using the class-A drying evaporation pan method with the cryogenic trap method. The results obtained from the evaporation pan water compare well with the cryogenic based method. Thus, the study establishes a cost-effective means of maintaining time series data of the isotopic composition of atmospheric moisture at meteorological observatories. The conclusions drawn in the present study are based on experiments conducted at Roorkee, India, and may be examined at other regions for its general applicability.     

In situ measurement of CO2 and water vapour isotopic compositions at a forest site using mid-infrared laser absorption spectroscopy

We conducted continuous, high time-resolution measurements of CO₂ and water vapour isotopologues (¹⁶O¹²C¹⁶O, ¹⁶O¹³C¹⁶O and ¹⁸O¹²C¹⁶O for CO₂, and H₂¹⁸O for water vapour) in a red pine forest at the foot of Mt. Fuji for 9 days from the end of July 2010 using in situ absorption laser spectroscopy. The δ¹⁸O values in water vapour were estimated using the δ²H–δ¹⁸O relationship. At a scale of several days, the temporal variations in δ¹⁸O-CO₂ and δ¹⁸O-H₂O are similar. The orders of the daily Keeling plots are almost identical. A possible reason for the similar behaviour of δ¹⁸O-CO₂ and δ¹⁸O-H₂O is considered to be that the air masses with different water vapour isotopic ratios moved into the forest, and changed the atmosphere of the forest. A significant correlation was observed between δ¹⁸O-CO₂ and δ¹³C-CO₂ values at nighttime (r²≈0.9) due to mixing between soil (and/or leaf) respiration and tropospheric CO₂. The ratios of the discrimination coefficients (Δ_a/Δ) for oxygen (Δ_a) and carbon (Δ) isotopes during photosynthesis were estimated in the range of 0.7–1.2 from the daytime correlations between δ¹⁸O-CO₂ and δ¹³C-CO₂ values.     

Accuracy and precision of a laser-spectroscopy approach to the analysis of δ2H and δ18O in human urine

The isotope ratio analysis of body water often involves large sample numbers and lengthy sample processing. Here we demonstrate the ability of isotope ratio infrared spectroscopy (IRIS) to rapidly and accurately analyse the isotope ratios of water in urine. We analysed water extracted from human urine using traditional isotope ratio mass spectrometry (IRMS) and compared those values with IRIS-analysed extracted water and un-extracted urine. Regression analyses for δ²H and δ¹⁸O values between (1) extracted water analysed via IRMS and IRIS and (2) urine and extracted water analysed via IRIS were significant (R ²=0.99). These results indicate that cryogenic distillation of urine was not required for an accurate estimate of the isotopic composition of urine when using IRIS.     

Combined approach of isotope mass balance and hydrological water balance methods to constrain the sources of lake water as exemplified on the small dimictic lake Silbersee,northern Germany

Stable isotopes of hydrogen and oxygen are often used for water balance calculations of lakes. We present an approach combining the lake water balance with an isotope mass balance to constrain the sources and sinks of the water of a small dimictic lake subjected to eutrophication. Meteorological and hydraulic data in combination with measured isotope signatures of the different water compartments enabled to assess the degree of surface water/groundwater interaction and the amount of overland flow into the lake. Groundwater could be excluded as a lake water source, as its water level was always below the lake water level. In the absence of a channelled inflow, precipitation and overland flow were the remaining options, whereby the latter was only active during periods of exceptionally high rainfall. While the groundwater signatures adjacent to the lake showed an influence of lake water, the lake water balance itself indicated that the associated volumetric water loss to groundwater is rather negligible. In the present case, only a combined assessment of hydrological and isotopic data allowed for an accurate characterization of the studied lake and a quantification of its water sources and sinks, highlighting the importance of using more than one methodological approach for such a purpose.     

High-precision measurements of δ2H, δ18O and δ17O in water with the aid of cavity ring-down laser spectroscopy

A thorough evaluation of measurement uncertainty together with control of short-term and long-term precision of measurements should be a basis of any successful quality assurance/quality control (QA/QC) strategy aimed at maintaining a high quality of the analytical process. Here we present the results of a comprehensive assessment of the analytical performance of a Picarro L2140-i CRDS laser spectrometer analysing δ²H, δ¹⁸O and δ¹⁷O in water. The assessment is based on results obtained during 15 months of continuous operation of this instrument (February 2017 to May 2018). The short-term precision of measured and derived quantities was 0.11, 0.036, 0.028, 0.23 ‰ and 11 per meg, for δ²H, δ¹⁸O, δ¹⁷O, d-excess and Δ¹⁷O, respectively, and is comparable to the precision reported by the manufacturer. The long-term precision of the L2140-i, defined as standard uncertainty of the time series of 153 analyses of a laboratory standard conducted throughout 15 months, was roughly two times lower (0.24, 0.053, 0.038, 0.37 ‰ and 21 per meg, for δ²H, δ¹⁸O, δ¹⁷O, d-excess and Δ¹⁷O). In-depth assessment of the measurement uncertainty of a single analysis revealed that assigned uncertainty of the calibration standards is an important component of the uncertainty budget, especially in case of δ²H analysis.     

A continuous stream flash evaporator for the calibration of an IR cavity ring-down spectrometer for the isotopic analysis of water

A new technique for high-resolution simultaneous isotopic analysis of δ¹⁸O and δD in liquid water is presented. A continuous stream flash evaporator has been designed that is able to vapourise a stream of liquid water in a continuous mode and deliver a stable and finely controlled water vapour sample to a commercially available infrared cavity ring-down spectrometer. Injection of sub-microlitre amounts of the liquid water is achieved by pumping liquid water sample through a fused silica capillary and instantaneously vapourising it with 100% efficiency in a home-made oven at a temperature of 170?°C. The system's simplicity, low power consumption and low dead volume together with the possibility for automated unattended operation provides a solution for the calibration of laser instruments performing isotopic analysis of water vapour. Our work is mainly driven by the possibility to perform high-resolution online water isotopic analysis on continuous-flow analysis (CFA) systems typically used to analyse the chemical composition of ice cores drilled in polar regions. In the following, we describe the system's precision and stability and sensitivity to varying levels of sample size and we assess the observed memory effects. A test run with standard waters of different isotopic compositions is presented, demonstrating the ability to calibrate the spectrometer's measurements on a VSMOW scale with a relatively simple and fast procedure.     

Defining a stable water isotope framework for isotope hydrology application in a large trans-boundary watershed (Russian Federation/Ukraine)

Stable isotopes of hydrogen (²H) and oxygen (¹⁸O) of the water molecule were used to assess the relationship between precipitation, surface water and groundwater in a large Russia/Ukraine trans-boundary river basin. Precipitation was sampled from November 2013 to February 2015, and surface water and groundwater were sampled during high and low flow in 2014. A local meteoric water line was defined for the Ukrainian part of the basin. The isotopic seasonality in precipitation was evident with depletion in heavy isotopes in November–March and an enrichment in April–October, indicating continental and temperature effects. Surface water was enriched in stable water isotopes from upstream to downstream sites due to progressive evaporation. Stable water isotopes in groundwater indicated that recharge occurs mainly during winter and spring. A one-year data set is probably not sufficient to report the seasonality of groundwater recharge, but this survey can be used to identify the stable water isotopes framework in a weakly gauged basin for further hydrological and geochemical studies.     

Comparison of sample preparation methods for stable isotope analysis of dissolved sulphate in forested watersheds

Pretreatment methods for measuring stable sulphur (δ³⁴S) and oxygen (δ¹⁸O) isotope ratios of dissolved sulphate from watersheds have evolved throughout the last few decades. The current study evaluated if there are differences in the measured stable S and O isotope values of dissolved sulphate from forested watersheds when pretreated using three different methods: Method 1 (M1): adsorb sulphate on anion exchange resins and send directly to isotope facility; Method 2 (M2): adsorb sulphate on anion exchange resins, extract sulphate from anion exchange resins, and send the produced BaSO₄ to the isotope facility; and Method 3 (M3): directly precipitate BaSO₄ without anion exchange resins with the precipitates being sent to the isotope facility. We found an excellent agreement of the δ³⁴S_sulphate values among all the three methods. However, some differences were observed in the δ¹⁸O_sulphate values (M1 versus M2:?1.5 ‰; M1 versus M3:?1.2 ‰) associated with possible O contamination before isotope measurement. Several approaches are recommended to improve the pretreatment procedures for δ¹⁸O_sulphate analysis.     

Breath water-based doubly labelled water method for the noninvasive determination of CO2 production and energy expenditure in mice

ABSTRACT

We explored a novel doubly labelled water (DLW) method based on breath water (BW-DLW) in mice to determine whole body CO₂ production and energy expenditure noninvasively. The BW-DLW method was compared to the DLW based on blood plasma. Mice (n?=?11, 43.5?±?4.6?g body mass (BM)) were administered orally a single bolus of doubly labelled water (1.2?g H₂¹⁸O kg BM^?1 and 0.4?g ²H₂O kg BM^?1, 99 atom% (AP) ¹⁸O or ²H). To sample breath water, the mice were placed into a respiration vessel. The exhaled water vapour was condensed in a cold-trap. The isotope enrichments of breath water were compared with plasma samples. The ²H/¹H and ¹⁸O/¹⁶O isotope ratios were measured by means of isotope ratio mass spectrometry. The CO₂ production (RCO₂) was calculated from the ²H and ¹⁸O enrichments in breath water and plasma over 5 days. The isotope enrichments of breath water vs. plasma were correlated (R²?=?0.89 for ²H and 0.95 for ¹⁸O) linearly. The RCO₂ determined based on breath water and plasma was not different (113.2?±?12.7 vs. 111.4?±?11.0?mmol?d^–1), respectively. In conclusion, the novel BW-DLW method is appropriate to obtain reliable estimates of RCO₂ avoiding blood sampling.     

Comparison of pore water samplers and cryogenic distillation under laboratory and field conditions for soil water stable isotope analysis*

We used pore water samplers (PWS) to sample for isotope analysis (1) only water, (2) soil under laboratory conditions, and (3) soil in the field comparing the results with cryogenic extraction (CE). In (1) and (2), no significant differences between source and water extracted with PWS were detected with a mean absolute difference (MAD) always lower than 2?‰ for δ²H and 1?‰ for δ¹⁸O. In (2), CE water was more enriched than PWS-extracted water, with a MAD respect to source water of roughly 8?‰ for δ²H and 4?‰ for δ¹⁸O. In (3), PWS water was enriched relative to CE water by 3?‰ for δ²H and 0.9?‰ for δ¹⁸O. The latter result may be due to the distinct water portions sampled by the two methods. Large pores, easily sampled by PWS, likely retain recent, and enriched, summer precipitation while small pores, only sampled by CE, possibly retain isotopically depleted water from previous winter precipitation or irrigation inputs. Accuracy and precision were greater for PWS relative to CE. PWS is therefore suggested as viable tool to extract soil water for stable isotope analysis, particularly for soils used in this study (sandy and silty loams).     

A simple polymer electrolyte membrane system for enrichment of low-level tritium (3H) in environmental water samples

Tritium (³H) is an essential tracer of the Earth's water cycle; yet widespread adoption of tritium in hydrologic studies remains a challenge because of analytical barriers to quantification and detection of ³H by electrolytic pre-concentration. Here, we propose a simple tritium electrolytic enrichment system based on the use of solid polymer electrolyte membranes (PEMs) that can be used to enrich ³H in 250–3000?mL environmental water samples to a 10-mL final volume. The IAEA PEM-³H system reported here can produce high enrichment factors (>70-fold) and, importantly, removes some of the deterrents to conventional ³H enrichments methods, including the use of toxic electrolysis and neutralization chemicals, spike standards, a complex electrolysis apparatus that requires extensive cooling and temperature controls, and improves precision by eliminating the need for tracking recovery gravimetrics. Preliminary results with varying operating conditions show ³H enrichments to 70-fold and higher are feasible, spanning a wide range of tritium activities from 5 to 150 TU with a precision of ～4.5?%. Further work is needed to quantify inter-sample memory and to establish lower ³H detection limits. The IAEA PEM-³H system is open source, with 3-D CAD and design files made freely available for adoption and improvement by others.     

USGS48 Puerto Rico precipitation – a new isotopic reference material for δ2H and δ18O measurements of water

A new secondary isotopic reference material has been prepared from Puerto Rico precipitation, which was filtered, homogenised, loaded into glass ampoules, sealed with a torch, autoclaved to eliminate biological activity, and calibrated by dual-inlet isotope-ratio mass spectrometry. This isotopic reference material, designated as USGS48, is intended to be one of two isotopic reference waters for daily normalisation of stable hydrogen (δ²H) and stable oxygen (δ¹⁸O) isotopic analysis of water with a mass spectrometer or a laser absorption spectrometer. The δ²H and δ¹⁸O values of this reference water are?2.0±0.4 and?2.224±0.012 ‰, respectively, relative to Vienna Standard Mean Ocean Water on scales normalised such that the δ²H and δ¹⁸O values of Standard Light Antarctic Precipitation reference water are?428 and?55.5 ‰, respectively. Each uncertainty is an estimated expanded uncertainty (U=2u_c) about the reference value that provides an interval that has about a 95 % probability of encompassing the true value. This isotopic reference water is available by the case of 144 glass ampoules containing 5 mL of water in each ampoule.     

Role of water contamination within the GC column of a GasBench II peripheral on the reproducibility of 18O/16O ratios in water samples

The GasBench II peripheral along with MAT 253 combination provides a more sensitive platform for the determination of water isotope ratios. Here, we examined the role of adsorbed moisture within the gas chromatography (GC) column of the GasBench II on measurement uncertainties. The uncertainty in ¹⁸O/¹⁶O ratio measurements is determined by several factors, including the presence of water in the GC. The contamination of GC with water originating from samples as water vapour over a longer timeframe is a critical factor in determining the reproducibility of ¹⁸O/¹⁶O ratios in water samples. The shift in isotope ratios observed in the experiment under dry and wet conditions correlates strongly with the retention time of analyte CO₂, indicating the effect of accumulated moisture. Two possible methods to circumvent or minimise the effect of adsorbed water on isotope ratios are presented here. The proposed methodology includes either the regular baking of the GC column at a higher temperature (120 °C) after analysis of a batch of 32 sample entries or conducting the experiment at a low GC column temperature (22.5 °C). The effects of water contamination on long-term reproducibility of reference water, with and without baking protocol, have been described.     

Temporal and spatial distribution of isotopes in river water in Central Europe: 50 years experience with the Austrian network of isotopes in rivers

The Austrian network of isotopes in rivers comprises about 15 sampling locations and has been operated since 1976. The Danube isotope time series goes back to 1963. The isotopic composition of river water in Central Europe is mainly governed by the isotopic composition of precipitation in the catchment area; evaporation effects play only a minor role. Short-term and long-term isotope signals in precipitation are thus transmitted through the whole catchment. The influence of climatic changes has become observable in the long-term stable isotope time series of precipitation and surface waters. Environmental ³H values were around 8 TU in 2015, short-term ³H pulses up to about 80 TU in the rivers Danube and March were a consequence of releases from nuclear power plants. The complete isotope data series of this network will be included in the Global Network of Isotopes in Rivers database of the International Atomic Energy Agency (IAEA) in 2017. This article comprises a review of 50 years isotope monitoring on rivers and is also intended to provide base information on the (isotope-)hydrological conditions in Central Europe specifically for the end-users of these data, e.g. for modelling hydrological processes. Furthermore, this paper includes the 2006–2015 supplement adding to the Danube isotope set published earlier.     

Groundwater of the Crimean peninsula: a first systematic study using stable isotopes

ABSTRACT

Karst springs in the Main Range of the Crimean Mountains and the Crimean Piedmont show a restricted range of values (δ¹⁸O?=?–10.5 to –8.0 ‰, δ²H?=?–72 to –58 ‰), somewhat more negative than the weighted mean of meteoric precipitation. This suggests preferential recharge at higher elevations during winter months. Groundwater tapped by boreholes splits in three groups. A first group has isotopic properties similar to those of the springs. The second group shows significantly lower values (δ¹⁸O?=?–13.3 to –12.0 ‰, δ²H?=?–95 to –82 ‰), suggesting recharge during colder Pleistocene times. The third group has high isotope values (δ¹⁸O?=?–2.5 to +1.0 ‰, δ²H?=?–24 to –22 ‰); the data points are shifted to the right of the Local Meteoric Water Line, suggesting water–rock exchange processes in the aquifer. These boreholes are located in the Crimean Plains and discharge mineralized (ca. 25 g L^?1) thermal (65°C) water from a depth of 1600–1800 m. Groundwater associated with mud volcanoes on the Kerch peninsula have distinct isotope characteristics (δ¹⁸O?=?–1.6 to +9.4 ‰, δ²H?=?–30 to –18 ‰). Restricted δ²H variability along with variable and high δ¹⁸O values suggest water–rock interactions at temperatures exceeding 95 °C.     

Ultra trace determination of fluorobenzoic acids in reservoir and ground water using isotope dilution gas chromatography mass spectrometry

The accurate ultra-trace analysis of six fluorobenzoic acids (FBAs) via isotope dilution gas chromatography mass spectrometry through their deuterated analogues is described. North Sea reservoir and ground water samples were spiked with six deuterated FBAs (dFBAs), enriched using solid-phase extraction (SPE) and analysed using GC/MS after derivatisation with BF ₃· MeOH. All FBAs were enriched and determined simultaneously. SPE allowed a 250-fold enrichment of the acids if 100 mL of sample volume was used. The method enables the determination of FBAs down to the range of 8–37 ng L ^?1 with recoveries between 66 % and 85 %. It uses low amounts of chemicals and is adaptable to larger and smaller sample volumes.