Spectral broadening of femtosecond pulses in an nonlinear optical fiber amplifier

A promising method for the generation of a supercontinuum with a high spectral power density based on the spectral broadening of ultrashort pulses in a fiber amplifier is considered. The advantage of the method, as compared to the conventional way of the supercontinuum generation in a microstructure fiber, is a lower pulse spectral broadening rate, which allows one to achieve higher SC spectral power densities. The initial stage of the supercontinuum generation in an ytterbium fiber amplifier (a fiber core diameter of 7 μm) with side pumping from an array of laser diodes with a total power of 8 W at a wavelength of 976 nm is experimentally studied. Yb:KYW laser pulses with a duration of 250 fs, a central wavelength of 1046 nm, and an average power of 150 mW have been supplied to the input of the amplifier. In this case spectrally broadened radiation with an average spectral power density of higher than 65 mW/nm and a spectrum width of 50 nm has been obtained.     

Solid-state Er:Yb:glass laser mode-locked by using single-wall carbon nanotube thin film

We design single-wall carbon nanotube (SWNT) thin-film saturable absorbers (SAs) integrated onto semiconductor distributed Bragg reflectors for mode-locking solid-state Er:Yb:glass lasers. We characterize the low nonsaturable loss, high-damage-threshold SWNT SAs and verify their operation up to a pulse fluence of 2 mJ/cm(2). We demonstrate passive fundamental continuous-wave mode locking with and without group-delay dispersion compensation. Without compensation the laser produces chirped 1.8 ps pulses with a spectral width of 3.8 nm. With compensation, we obtain 261 fs Fourier-transform-limited pulses with a spectral width of 9.6 nm.     

滤波对8字腔掺铒光纤激光器锁模运转的影响

构建了基于损耗非对称非线性光学环镜的8字腔掺铒光纤锁模激光器,并讨论了腔内滤波带宽对腔内脉冲演化和激光器输出特性的影响.在非线性光学环镜中引入双向输出耦合器,耦合器和传输光纤位置的不对称产生非互易性,实现锁模运转.利用自制的可调谐滤波器实验研究了滤波带宽对激光器的影响.当滤波带宽为2.1 nm时,腔内脉冲的演化过程受滤波和孤子效应的共同作用,激光器顺时针和逆时针输出脉冲半高全宽分别为583.7fs和2.94 ps.随着滤波带宽增大,滤波的作用逐渐减弱,激光器两路输出脉冲参数逐渐接近,并接近傅里叶变换极限脉冲.当滤波带宽较大时,腔内脉冲的演化过程受增益谱和孤子效应的共同作用,激光器顺时针和逆时针输出脉冲均为变换极限脉冲,半高全宽约为440 fs.通过调节滤波器中心波长实现了对激光器输出脉冲光谱的连续调谐,调节范围大于30 nm.     

Picosecond pulses with 50 W peak power and reduced ASE background from an all-semiconductor MOPA system

Using a single-stage all-semiconductor master oscillator-power amplifier system, consisting of a Q-switched distributed Bragg reflector laser as master oscillator and a tapered power amplifier, we generate laser pulses with a length of 80 ps and a peak power of 50 W. The spectral width is less than 1 nm around a center wavelength of 1066 nm. The background of the amplified spontaneous emission is significantly reduced due to a pulsed, instead of continuous-wave operation of the amplifier. The current pulses have a width of approximately 10 ns and a repetition frequency of 1.25 MHz.     

Widely tunable sub-30-fs pulses from a compact erbium-doped fiber source

Coupling femtosecond light pulses from an all-fiber Er:laser system into a dispersion-shifted and highly non-linear fiber, we generate output spectra exhibiting two broadband and mutually coherent maxima. Depending on the chirp of the input pulse, the spectral separation is easily tunable over a wide range up to values exceeding 100 THz. In this way, the source provides access to an ultrabroadband wavelength interval from 1130 to 1950 nm. Because of soliton effects, the long-wave component exhibits a transform-limited pulse width of 40 fs directly after the nonlinear element. The high-frequency part propagating in the dispersive regime is recompressed to pulse durations as short as 24 fs with an optimized prism sequence.     

Stimulated Raman hyperspectral imaging based on spectral filtering of broadband fiber laser pulses

We demonstrate a technique of hyperspectral imaging in stimulated Raman scattering (SRS) microscopy using a tunable optical filter, whose transmission wavelength can be varied quickly by a galvanometer mirror. Experimentally, broadband Yb fiber laser pulses are synchronized with picosecond Ti:sapphire pulses, and then spectrally filtered out by the filter. After amplification by fiber amplifiers, we obtain narrowband pulses with a spectral width of <3.3 cm(-1) and a wavelength tunability of >225 cm(-1). By using these pulses, we accomplish SRS imaging of polymer beads with spectral information.     

Widely tunable mode-locked all-fiberized Yb-doped fiber laser with near-transform-limited spectrum linewidth

A widely tunable mode-locked all-fiberized Yb-doped fiber laser with near-transform-limited spectrum linewidth is used. It consists of a tunable fiber Bragg grating (TFBG) and a fiber-coupled LiNbO₃ phase modulator (PM) in a linear cavity. The TFBG is used to achieve tunable emission wavelength, and the intracavity PM is used to achieve actively mode-locking operation. We have experimentally demonstrated that the laser-emitting wavelength can be tuned between 1,041 and 1,091 nm with power fluctuation less than 3 dB. The temporal width of the laser pulse is about 1 ns, and the pulses are near transform-limited with a spectral linewidth of 1.3 GHz. The results may find useful application in optical communication and optical measurement system.     

Stable mode-locked fiber laser using 49 cm long bismuth oxide based erbium doped fiber and slow saturable absorber

A stable mode-locked fiber laser employing a 49 cm long bismuth oxide based erbium doped fiber (Bi-EDF) by using a slow saturable absorber is demonstrated. Near transform limited short pulses with a repetition rate of 8.27 MHz are obtained at a wavelength of 1560 nm with a maximum spectral width of 15 nm. Results indicate that pulse characteristics are strongly dependent on pump power rather than spectral width. Moreover the Time-Bandwidth products (TBWP), pulse duration, the energy fluctuation and timing jitter decrease with increasing pump power. The pulse width is continuously varied from 1.2 ps to less than 300 fs. It produces stable mode locking with a maximum spectral width of 15 nm, minimum timing jitter of 4 ps and energy fluctuations of 2.5%. The pulse train was amplified using a two-stage amplifier up to 447 mW average power corresponding to peak powers of 177.3 kW.     

Spectrally scanned,repetitively pulsed erbium-doped fiber laser for spectral and temporal multiplexing of fiber Bragg grating sensors

An erbium-doped fiber laser that emits a series of spectrally scanned pulses is used to monitor an array of fiber Bragg grating (FBG) sensors. The cavity for this Fabry-Perot laser is formed by two spectrally selective reflectors: a rotating mirror-grating combination for scanning the reflectance peak wavelength and a fiber Fabry-Perot interferometer (FFPI) with a periodic reflectance spectrum. During a scan of the rotating mirror, the laser produces a set of Q-switched pulses over the 1522-1568-nm spectral range at each of the FFPI reflectance peak wavelengths. This laser is used to simultaneously demonstrate wavelength-division multiplexing of FBGs with reflectance peaks in different spectral regimes and time-division multiplexing of FBGs with overlapping spectra. The spectral location of the FBG peaks was determined to an accuracy of 1.4 pm.     

Hollow-fiber compression of 6 mJ pulses from a continuous-wave diode-pumped single-stage Yb,Na:CaF2 chirped pulse amplifier

Here, 200 fs 6 mJ pulses from a cw diode-pumped Yb,Na:CaF(2) amplifier are spectrally broadened in an Ar- or Ne-filled hollow-core fiber and recompressed to 20 fs (Ar) and 35 fs (Ne) using a prism pair. The results of spectral broadening and phase measurement are in excellent agreement with numerical modeling based on the generalized nonlinear Schr?dinger equation. The longer laser wavelength of 1030 nm permits favorable energy scaling for the hollow-fiber technique compared to ultrafast amplifiers operating at 800 nm.     

Multi-millijoule, nonlinear preamplifier for high intensity femtosecond Yb:YAG chirped-pulse amplification lasers at 1030 nm

We report the highest energy broadband laser pulses at a center wavelength of 1030 nm based on optical parametric chirped-pulse amplification (OPCPA). We have demonstrated amplification of 1030 nm femtosecond laser pulses from a broadband Yb oscillator to over 6.5 mJ with a total gain of greater than 10⁷ achieved in a single pass through only 56 mm of gain material at a 10 Hz repetition rate. The amplified spectral bandwidth of 10.8 nm affords recompression to a 230 fs pulse duration following amplification. As an alternative to the regenerative amplifier (RA) this system is one of the more promising candidates for realizing compact, high intensity, direct diode-pumped, high repetition rate femtosecond Yb:YAG chirped-pulse amplification (CPA) in laser systems.     

Diode-pumped sub-100 fs Kerr-lens mode-locked Yb3+:Sc2O3 ceramic laser

Diode-pumped Kerr-lens mode-locked laser operations of Yb3+:Sc2O3 ceramics have been achieved. 92 fs pulses with the average power of 850 mW under 3.89 W incident pump power were obtained at a center wavelength of 1042 nm. The optical-to-optical efficiency was 21.9%. 90 fs pulses with the average power of 160 mW were also obtained at a center wavelength of 1092 nm. To our knowledge, this is the first demonstration of a Kerr-lens mode-locked Yb3+:Sc2O3 laser.     

Compact laser source for high-power white-light and widely tunable sub 65 fs laser pulses

We demonstrate an Yb:KGW femtosecond solitary mode-locked laser oscillator, which is used as a pump source for tapered fibers to generate white-light laser pulses with an average output power of up to 2.5 W and a spectral bandwidth of over 1000 nm. By spectrally filtering these pulses and subsequent compression of the filtered pulses with a prism sequence, we are able to generate ultrashort laser pulses with durations between 26 and 65 fs that are tunable from 600 to 1450 nm and with tens to several hundreds of milliwatts of average power.     

宽带可调谐掺Yb3+双包层光纤激光器的研究

利用闪耀光栅构成可调谐Littrow外腔,对掺Yb³⁺双包层光纤激光器的波长调谐输出进行了实验研究.激光调谐输出波长范围70nm.针对光纤内的双折射效应对激光的输出功率的影响,实验中使用了在线光纤偏振控制器,从而有效地减小了调谐曲线的起伏及其与荧光谱的差别,并得到了窄线宽、线偏振、宽带调谐的激光输出.     

Tunable sub-100 femtosecond dye-laser pulses generated with a nanosecond pulsed pumping

Subpicosecond pulses at a fixed wavelength produced with a low-Q cavity dye laser pumped by a single, nanosecond laser (Q-switched Nd:YAG) are converted into tunable high-power sub-100 femtosecond pulses by generation, spectral selection, amplification and compression of a supercontinuum. The tunable, chirped, high-energy pulses obtained are compressed with a prism pair. Energies up to 50 J in sub-100 fs pulses were obtained in the 540 to 650 nm range using 40 mJ of the Nd: YAG-laser pumping pulses at 532 nm. The whole sub-100 fs system including the low-Q dye laser uses only one Nd:YAG laser as a pump source.     

Volume Bragg grating stabilized spectrally narrow Tm fiber laser

A Tm-doped large mode area (LMA) silica fiber laser has been locked to a stable wavelength of 2,053.9 nm using a volume Bragg grating (VBG). The measured spectral width of the laser output was <300 pm, limited by the spectrometer resolution. Although this laser had modest output (approximately 5W) and slope efficiency (41%), this new approach to spectrally limiting the output of LMA fiber lasers is inherently extendable to kilowatt powers, opening up several applications including high-power pulsed fiber lasers and spectral beam combining. Performance characteristics of the laser compared to one using a dielectric mirror as a high reflector are described, and the results imply low VBG losses.     

Narrow-wavelength-spread spectral combining laser with a reflector for a double pass with a single grating

We proposed a novel wavelength-spread compression technique for spectral beam combining of a diode laser array. A reflector, which is parallel to the grating, is introduced to achieve a double pass with a single grating.This facilitated the reduction of the wavelength spread by half and doubled the number of combined elements in the gain range of the diode laser. We achieved a power of 26.1 W under continuous wave operation using a19 element single bar with a wavelength spread of 6.3 nm, which is nearly half of the original wavelength spread of 14.2 nm, demonstrating the double-compressed spectrum capability of this structure. The spectral beam combining efficiency was 63.7%. The grating efficiency and reflector reflectance were both over 95%; hence, the efficiency loss of the double-pass grating with a reflector is acceptable. In contrast to double-grating methods,the proposed method introduces a reflector that efficiently uses the single grating and shows significant potential for a more efficient spectral beam combining of diode laser arrays.     

Sub-60-fs ytterbium-doped fiber laser with a fiber-based dispersion compensation

We present a mode-locked ytterbium fiber laser with a higher-order mode fiber compensating the group-velocity dispersion and partially the third-order dispersion of the single-mode fiber at a wavelength of 1 microm. The generated pulses had an energy of 0.5 nJ and could be dechirped externally to a pulse duration of less than 60 fs. The power spectrum shows a spectral full width at half-maximum of 57 nm.     

Passive Q switching and self-frequency Raman conversion in a diode-pumped Yb:KGd(WO(4))(2) laser

We report on the laser performance of a diode-pumped Yb:KGd(WO(4))(2) laser that is passively Q switched with a Cr(4+):YAG saturable absorber. Raman conversion of fundamental laser emission in the laser crystal was demonstrated. Q-switched 3.4-mu;J pulses with a pulse width of 85 ns were obtained at the 1033-nm fundamental wavelength and 0.4-mu;J pulses with a pulse width of 20 ns were produced in a first Stokes at 1139 nm.     

Femtosecond oscillator on Yb:KYW crystal pumped by laser diode with fiber output

A femtosecond laser based on an Yb:KYW crystal with direct longitudinal pumping by a high-power semiconductor injection laser with a fiber output is described. Femtosecond pulses were generated in the self-longitudinal-mode-locking operating condition due to the use of a semiconductor saturable absorber. The average power of the oscillator was as high as 3.5 W at a central wavelength of 1035 nm, the pulse length and pulse repetition rate being 200 fs and 85.5 MHz, respectively. The product of the pulse length and the radiation spectrum width was 1.3 times higher than the theoretical limit for the pulse shape described by the function sech². The designed master oscillator can be also used as a stand-alone source of femtosecond radiation pulses for material microprocessing and primary source for femtosecond laser amplification systems.