P3HT∶PCBM薄膜成膜过程对聚合物太阳能电池性能的影响

P3HT∶PCBM薄膜的快速和缓慢成膜过程能显著的改变异质结聚合物太阳能电池性能。通过调节旋转时间以及薄膜退火前的间隔时间,研究了P3HT∶PCBM混合薄膜缓慢生长所需最佳时间。结果表明,在转速800 r.min-1下旋涂薄膜,经过50~80 s的旋涂,接着放置样品薄膜30 min以上,然后再对薄膜进行退火处理,电池效率可以达到3%以上,而快速成膜的电池效率只有1.8%左右。合理的P3HT和PCBM相分离促进了相应载流子的跳跃和传输,是提高电池效率的根本原因。研究结果为准确掌控缓慢生长的混合薄膜提供了时间窗口。     

不同环境压强下溶剂退火对聚合物太阳能电池性能的影响

通过改变溶剂退火时的环境压强控制溶剂的蒸发速率,在不同压强下进行加压溶剂退火制备了基于聚-3己基噻吩:富勒烯衍生物(P3HT:PCBM)的体异质结聚合物太阳能电池。X射线衍射(XRD)、紫外-可见吸收光谱(UV-Vis)以及原子力显微镜(AFM)的测试结果表明,增大溶剂退火的环境气压改善了薄膜的结晶度,增强了有源层的光吸收,提高了P3HT和PCBM的相分离程度,更有利于激子的解离和载流子传输。与在常压下溶剂退火相比,在2.0 MPa压强下对有源层进行溶剂退火的器件的光电转换效率提高了29%,达到了3.69%。     

二甲基亚砜添加剂对聚合物太阳能电池性能的影响

研究了二甲基亚砜(DMSO)掺杂浓度对基于聚(3-己基噻吩)(P3HT)和(6,6)-苯基碳60丁酸甲酯(PCBM)为有源层的聚合物太阳能电池性能影响。结果表明,掺杂DMSO可以提高聚合物太阳能电池短路电流密度和填充因子。DMSO掺杂质量比为3%时,电池短路电流密度提高到7.88 mA·cm-2,填充因子为55.5%。能量转换效率达到2.54％,相比没有掺杂DMSO的电池,能量转换效率提高了17%。傅里叶变换红外光谱被用于鉴定和分析掺杂DMSO对材料P3HT∶PCBM化学性质的影响。傅里叶变换红外光谱表明,掺杂后P3HT和PCBM的化学性质都没有改变。为分析掺杂DMSO改善器件能量转换效率的原因,通过紫外-可见光谱和电流密度-电压特性曲线分别表征器件的光吸收能力以及电致发光器件的载流子迁移率。与P3HT∶PCBM薄膜相比,P3HT∶PCBM∶DMSO薄膜在可见光范围内的吸收峰有明显红移且吸收强度增强。可见光吸收的改善是实现短路电流密度提高的有力保障。太阳能电池性能的增强是因为DMSO的掺杂提高了P3HT∶PCBM的载流子迁移率和吸收光谱宽度。     

二甲基亚砜添加剂对聚合物太阳能电池性能的影响（英文）

研究了二甲基亚砜(DMSO)掺杂浓度对基于聚(3-己基噻吩)(P3HT)和(6,6)-苯基碳60丁酸甲酯(PCBM)为有源层的聚合物太阳能电池性能影响。结果表明,掺杂DMSO可以提高聚合物太阳能电池短路电流密度和填充因子。DMSO掺杂质量比为3%时,电池短路电流密度提高到7.88mA·cm-2,填充因子为55.5%。能量转换效率达到2.54%,相比没有掺杂DMSO的电池,能量转换效率提高了17%。傅里叶变换红外光谱被用于鉴定和分析掺杂DMSO对材料P3HT∶PCBM化学性质的影响。傅里叶变换红外光谱表明,掺杂后P3HT和PCBM的化学性质都没有改变。为分析掺杂DMSO改善器件能量转换效率的原因,通过紫外-可见光谱和电流密度-电压特性曲线分别表征器件的光吸收能力以及电致发光器件的载流子迁移率。与P3HT∶PCBM薄膜相比,P3HT∶PCBM∶DMSO薄膜在可见光范围内的吸收峰有明显红移且吸收强度增强。可见光吸收的改善是实现短路电流密度提高的有力保障。太阳能电池性能的增强是因为DMSO的掺杂提高了P3HT∶PCBM的载流子迁移率和吸收光谱宽度。     

溶剂预处理结合热退火提升聚噻吩结晶度及其光伏性能

活性层的微观形貌在很大程度上决定了聚合物光伏器件的性能表现并依赖于制备工艺条件。为了改善薄膜内部分子排布结构并追求较高的器件光电转化效率,采用溶液法制备了基于P3HT∶PCBM的聚合物太阳能电池(器件结构:ITO/PEDOT∶PSS/P3HT∶PCBM/Al),通过改变器件制备流程中活性层退火处理工艺,研究了热退火、溶剂退火以及溶剂预处理结合热处理的双重退火对聚合物太阳电池性能的影响。研究发现:双重退火的光伏器件的各项性能参数均优于单一退火处理器件,获得了3.25%的光电转化效率。原子力显微镜及X射线衍射仪的表征结果进一步证明:双重退火处理能够在促进聚合物给体良好有序结晶的同时保证共混组分适度地相分离,从而有利于光生激子的解离以及载流子的传输。     

溶剂预处理结合热退火提升聚噻吩结晶度及其光伏性能

活性层的微观形貌在很大程度上决定了聚合物光伏器件的性能表现并依赖于制备工艺条件。为了改善薄膜内部分子排布结构并追求较高的器件光电转化效率,采用溶液法制备了基于P3HT：PCBM的聚合物太阳能电池（器件结构:ITO/PEDOT：PSS/P3HT：PCBM/Al）,通过改变器件制备流程中活性层退火处理工艺,研究了热退火、溶剂退火以及溶剂预处理结合热处理的双重退火对聚合物太阳电池性能的影响。研究发现:双重退火的光伏器件的各项性能参数均优于单一退火处理器件,获得了3.25%的光电转化效率。原子力显微镜及X射线衍射仪的表征结果进一步证明:双重退火处理能够在促进聚合物给体良好有序结晶的同时保证共混组分适度地相分离,从而有利于光生激子的解离以及载流子的传输。     

基于透射率曲线确定聚合物太阳能电池功能层的光学常数和厚度

本文介绍了一种确定聚合物太阳能电池功能层光学常数和厚度的方法. 该方法借助于特定的色散模型拟合透射率测试曲线以获得功能层光学常数和厚度值. 文中比较了Forouhi-Bloomer和Lorentz-Oscillator模型在体异质结薄膜的透射率拟合计算中的适用性, 计算了poly(3-hexylthiophene)(P3HT)/[6,6]-phenylC₆₁-butyric acid methyl ester (PCBM)和 poly[2-methoxy-5-5(2'-ethyl-hexyloxy)-1,4-phenylenevinylene](MEH-PPV)/PCBM体异质结薄膜的光学常数和厚度. 拟合得到的曲线与实验曲线符合良好, 厚度计算的结果与台阶仪测量结果保持一致, 误差小于4%. 进一步分析得到的热退火和加入高沸点溶剂添加剂后P3HT/PCBM薄膜的光学常数和光学禁带值与相应器件伏安特性相符. 该方法适用于所有体异质结的功能层, 可用于聚合物太阳能电池的膜系优化和在线检测.     

缓冲层提高有机聚合物光伏电池性能研究

在分析有机聚合物复合体光伏电池机理及等效电路模型基础上,研究了界面旋涂缓冲层对聚合物给体/受体复合体结构光伏器件性能的影响.制备了基于P3HT/PCBM的给体 受体复合体薄膜有机光伏电池,并分别在有机活性层和ITO基底之间以及有机活性层和电极之间插入TFB和F8BT缓冲层.实验证明：在ITO和活性层之间旋涂TFB作为阳极缓冲层,可增加有机聚合物光伏器件的短路电流,在活性层和电极之间插入F8BT作为阴极缓冲层,可增大光伏器件的开路电压,提高器件的转换效率.     

热处理对不同溶剂制备的共混体系太阳电池性能影响

本文以poly(3-hexylthiophene) (P3HT)为电子给体材料, -phenyl C₆₁-butyric acid methyl ester (PCBM)为电子受体材料, 制备出不同溶剂形成的共混体系太阳电池.从薄膜的紫外—可见吸收光谱(UV-vis)、光致发光谱(PL)、原子力表面图形(AFM)等方面,分析了热处理对不同溶剂制备的共混体系太阳电池性能的影响.结果表明较高沸点的溶剂有利于P3HT:PCBM共混体系中P3HT的有序化排列,薄膜的紫外—可见吸收和光致发光增 关键词： 热处理 不同溶剂 太阳电池 性能     

退火处理ZnPc(OC_8H_(17)OPyCH_3I)_8阴极缓冲层的倒置有机太阳能电池

制备了以Zn Pc(OC8H17OPy CH3I)8为阴极缓冲层、P3HT∶PCBM为有源层的有机太阳能电池。对阴极缓冲层Zn Pc(OC8H17OPy CH3I)8薄膜分别进行了溶剂蒸汽退火和过渡舱惰性气体流退火处理,并利用原子力显微镜(AFM)对缓冲层表面形貌进行了表征。结果表明:这两种退火方法都使缓冲层形貌得以改善。电池效率从2.14%提高到3.76%,电流密度从8.12 m A/cm2提高到10.71 m A/cm2,填充因子从0.45提高到0.61。与传统器件相比,退火处理的阴极缓冲层器件的稳定性也得到了改善,器件寿命延长了1.4倍。这种简单阴极界面处理方法为改善聚合物太阳能电池性能提供了有效途径。     

Inverted organic solar cells comprising low-temperature-processed ZnO films

Inverted organic solar cells are fabricated using low-temperature-annealed ZnO film as an electron transport layer. Uniform ZnO films were prepared by spin coating a diethylzinc (DEZ) precursor solution in air, followed by annealing at 100 °C. Organic solar cells prepared on these ZnO films with a 1:1 P3HT:PCBM blend as the active layer show a high power conversion efficiency of 4.03 %, which is more than 10 % higher than the PCE of solar cells comprising ZnO prepared via a high-temperature sol–gel route.     

Fe3O4纳米粒子对P3HT:PCBM电池的影响

为了提高太阳能电池的性能,研究磁性纳米粒子在外加磁场的作用下对聚合物太阳能电池有源层P3HT:PCBM成膜及太阳能电池性能的影响。本文采用热分解法制备了磁性Fe₃O₄纳米粒子,将不同质量分数的Fe₃O₄纳米粒子掺入到P3HT:PCBM溶液中,旋涂后在外加磁场的作用下自组成膜。通过TEM、XRD对制备的Fe₃O₄纳米粒子进行表征,并利用偏光显微镜、原子力显微镜对成膜质量进行探究。结果表明,采用热分解法制备的Fe₃O₄纳米粒子直径在10 nm左右,在外加磁场作用下,Fe₃O₄纳米粒子对成膜有一定的调控作用。当Fe₃O₄纳米粒子掺杂质量分数为1%时,太阳能电池器件的开路电压增加3.77%,短路电流增加24.93%,光电转换效率提高7.82%。     

Performance and stability studies of inverted polymer solar cells with TiO2 film as a buffer layer

TiO₂ based inverted polymer solar cells (PSCs) with a structure of fluorine-doped tin oxide (FTO)/TiO₂/P3HT:PCBM/PEDOT:PSS/Ag presented excellent air stabilities,; the power conversion efficiency (PCE) of devices exhibited only 15 % decay as compared to the highest value while being exposed in air-condition for more than 20 days. Interestingly, an overall enhancement of PCE from 3.5 % to 3.9 % was observed while the PSCs were exposed in air-condition up to 3 days; the improvement of performance was attributed to the TiO₂ films’ oxygen and water protection effect and the oxidation of Ag, which will benefit to form an effective work function match with the HOMO of P3HT leading to improved ohmic contact. However, the performance slowly decreased when the exposure time remains longer due to the physical adsorbed oxygen. UV–ozone treatment on the TiO₂ films’ leads to the formation of a metal-deficient oxide that results in a decreased PCE for the devices. Finally, X-ray photo-emission spectroscopy (XPS) was used to analyze the compositional changes of the TiO₂ films while they were exposed in air-condition or treated by UV–ozone.     

Preheated solvent exposure on P3HT:PCBM thin film: A facile strategy to enhance performance in bulk heterojunction photovoltaic cells

In this study, we explored the ability of a preheated solvent (methanol) to induce characteristic changes at the organic active layer/metal interface, thereby improving the performance of fabricated organic photovoltaic (OPV) cells composed of poly(3-hexylthiopene) (P3HT) and a [6,6]-phenyl-C₇₁-butyric acid methyl ester (PCBM) photoactive blend. Our results demonstrate that exposure to methanol (at room temperature, or preheated at 45 °C or 65 °C) improves the performance of the fabricated OPV cells. After preheated methanol exposure, the P3HT:PCBM thin films were tested for crystallinity, morphology, mobility, and photovoltaic characteristics. Our results revealed that use of the preheated solvent on the organic active layer significantly influences the micro/nano scale morphology and phase segregation of the P3HT:PCBM thin films, as well as the charge carrier mobility. It is hypothesized that the side chain ordering of P3HT and redistribution of PCBM could be results of the modified active layer. Consequently, OPV cells modified with the methanol preheated at 65 °C exhibited a power conversion efficiency (PCE) of 3.36%, with open-circuit voltage of 0.59 V, short-circuit current density of 13.83 mA/cm², and fill-factor of 0.41. In contrast, the unmodified P3HT:PCBM thin film (without methanol exposure) showed a PCE of only 2.13%.     

退火气压对于P3HT∶PCBM微观形貌及光伏性能的影响

通过精确设定不同的退火环境气压,实现对P3HT(Poly(3-hexylthiophene -2,5-diyl)与PCBM([6,6]-Phenyl C₆₁ butyric acid methyl ester)体系中聚噻吩结晶度以及共混相分离程度的控制,并在此基础上制备了结构为ITO/PEDOT∶PSS/P3HT∶PCBM/Al的正型光伏器件。在允许的压强设定范围内,器件各项性能参数均随退火环境压强的增大表现出先升高后下降的变化规律,并统一于气压设定为1 500 mTorr时获得最大值。从活性层的紫外-可见(UV-Vis)吸收光谱中发现P3HT在510 nm吸收峰以及550和600 nm肩峰附近的吸收强度随退火气压升高而增大,在气压为1 500 mTorr时达到最高,吸收强度的提升源于聚合物分子π—π堆叠的增加。原子力显微镜(AFM)进一步分析结果表明,高气压环境(>1 000 mTorr)能够促进P3HT∶PCBM共混组分在退火过程中形成较大程度的相分离,而当环境压强合适时(1 500 mTorr)适度的相分离利于聚合物形成良好有序结晶,从而能够提升活性层内部载流子传输能力,保证较高的短路电流与填充因子,制备的器件也因此表现出良好的光伏性能,光电转化效率达到3.56%。     

Metal-electrode-free inverted organic photovoltaics using electrospray-deposited PEDOT:PSS and spin-coated HAT-CN exciton blocking layer

Poly(3,4-ethylenedioxythiophene)-poly(styrene sulfonate) (PEDOT:PSS) films were fabricated using an electrospray deposition (ESD) method. The ESD PEDOT:PSS films exhibited higher PSS content on the surface than spin-coated PEDOT:PSS films, which results in a higher work function. Based on this result, metal-electrode-free inverted organic photovoltaics (OPVs) were fabricated. The ESD PEDOT:PSS was used as the top electrode on the poly(3-hexythiophene-2,5-diyl) (P3HT):[6,6]-phenyl C₆₁ butyric acid methyl ester (PCBM) light-absorbing layer. The power conversion efficiency (PCE) of OPVs was significantly increased with the 1,4,5,8,9,11-hexaazatriphenylene hexacarbonitrile layer. The improved PCE would be attributed to the suppression of exciton quenching at the P3HT:PCBM and PEDOT:PSS interface.     

Hybrid polymer/inorganic nanoparticle blended ternary solar cells

Hybrid polymer/inorganic nanoparticle blended ternary solar cells are reported. These solar cells have an active layer consisting of PbS colloidal quantum dots (CQDs), poly (3‐hexylthiophene) (P3HT), and [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM). Power conversion efficiency (PCE) was improved by incorporating PbS CQDs in the active layer of P3HT:PCBM‐based organic solar cells. As the concentration of PbS CQDs in the hybrid solar cells was increased, PCE was also increased. This improvement resulted from improved charge transfer and also extended light absorption into the near‐infrared. The PCE of the hybrid solar cells was 47% higher than that for reference organic solar cells on average under air mass 1.5 global illumination. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Solution processable reduced graphene oxide decorated ATO electrode for organic solar cells

A novel concept based on the use of solutions containing already qualified crystalline antimony-doped tin oxide SnO₂:Sb (ATO) nanoparticles has been developed. ATO nanoparticles are decorated by reduced graphene oxide (rGO) through a hydrothermal synthesis method. The electrical and optical properties of the graphene oxide films are investigated systematically. The sheet resistance (R _□) of the ATO–rGO films decreases with the increase in the rGO content in the precursor solution. The R _□ can be decreased after the ATO–rGO films annealing in the air for 1 h and can be further decreased by depositing Au on the surface of the films. The optimum property of the ATO–rGO film shows that the R _□ is 80 Ω/□ and the transmittance is about 70 %. The ATO–rGO films are used as the anode of the organic solar cells. The anode film impact on the performance of the devices is studied. Finally, the power conversion efficiency (PCE) of the device based on the poly-(3-hexylthiophene): [6, 6]-phenyl C61-butyric acid methyl ester (PCBM) blended is 1.85 %, and the PCE of the device based on the poly-benzo[1,2-b:4,5-b′] dithio-phene thieno[3,4-b] thiophene:PCBM blended is 3.4 %.     

退火温度对电子束蒸发沉积Cu_2O薄膜性能的影响

近年来,钙钛矿太阳电池(PSCs)得到了迅猛发展,而无机空穴传输材料(IHTMs)的使用可进一步降低电池的成本,提高电池的稳定性.本文通过电子束蒸发制备了Cu_2O薄膜,研究了空气中退火温度及时间对薄膜组成、结构及光电性能的影响,并构筑了p-i-n反型平面异质结钙钛矿太阳电池.研究发现:由于热解作用,直接通过电子束蒸发制备的薄膜为Cu_2O和Cu的混合物;而在空气中经过退火后,由于氧化作用,随着退火温度的升高,薄膜的组分由混合物转变为纯的Cu_2O,再转变成纯的CuO.通过控制退火温度制备的Cu_2O薄膜的光学带隙约为2.5 eV,载流子迁移率约为30 cm~2·V~(-1)·s~(-1).应用于PSCs,薄膜的最佳厚度为40 nm,但电池性能低于PEDOT:PSS基的PSCs.这主要是由于钙钛矿前驱液在Cu_2O薄膜的润湿性较差,吸收层中有大量微孔洞存在,致使漏电流增强,电池的性能降低.然而,当采用Cu_2O/PEDOT:PSS双HTMs设计时,由于PEDOT:PSS对Cu_2O具有较强的腐蚀作用,使电池性能恶化.