Improved Kinetic Rate Constants for Nylon 6, Nylon 6,6, and Nylon 6/6,6 Copolymer

Nylon 6 and 6,6 literature data are collected over a wide range of water concentrations and temperatures (0 ≤ [W]₀ ≤ 40.8 wt%, 200 ≤ T ≤300 °C) and used to fit parameters in an updated batch reactor model. The resulting copolymerization model uses side reactions to account for the complex influence of water on kinetics and reaction equilibria. The proposed parameter estimates result in a significant improvement in the fit to the data, corresponding to a 73% reduction in the weighted‐least‐squares objective function compared to when the parameters of Arai et al. are used. Copolymerization simulations are conducted at industrially relevant conditions, shedding light on the complex influence of water and on the potential to include waste nylon 6 cyclic dimer in the feedstock. The model and parameter estimates will be helpful in future models of nylon 6/6,6 copolymerization in continuous reactor systems.     

A Comparison of Simple Rheological Parameters and Simulation Data for Zymomonas mobilis Fermentation Broths with High Substrate Loading in a 3-L Bioreactor

Traditionally, as much as 80% or more of an ethanol fermentation broth is water that must be removed. This mixture is not only costly to separate but also produces a large aqueous stream that must then be disposed of or recycled. Integrative approaches to water reduction include increasing the biomass concentration during fermentation. In this paper, experimental results are presented for the rheological behavior of high-solids enzymatic cellulose hydrolysis and ethanol fermentation for biomass conversion using Solka Floc as the model feedstock. The experimental determination of the viscosity, shear stress, and shear rate relationships of the 10 to 20% slurry concentrations with constant enzyme concentrations are performed with a variable speed rotational viscometer (2.0 to 200 rpm) at 40 °C. The viscosities of enzymatic suspension observed were in range of 0.0418 to 0.0144, 0.233 to 0.0348, and 0.292 to 0.0447 Pa s for shear rates up to 100 reciprocal seconds at 10, 15, and 20% initial solids (w/v), respectively. Computational fluid dynamics analysis of bioreactor mixing demonstrates the change in bioreactor mixing with increasing biomass concentration. The portion-loading method is shown to be effective for processing high-solids slurries.     

Production of fuel alcohol from wheat by VHG technology

Very high gravity (VHG) wheat mashes containing more than 300 g of dissolved solids per liter were prepared and fermented with active dry yeast at 20, 25, 30, and 35°C with and without yeast extract as nutrient supplement. At 20°C, mashes with 38% (w/v) dissolved solids end-fermented without any nutrient supplementation and maximum ethanol yields of 23.8% (v/v) were obtained. With increasing temperatures, the sugar consumption decreased. Addition of yeast extract stimulated the rate of fermentation at all temperatures, but did not increase the total amount of sugar consumed. The stimulatory effect of yeast extract on cell multiplication decreased with increasing sugar concentration, and virtually no difference in cell number was observed between yeast extract-supplemented and unsupplemented mashes at sugar concentrations above 33% (w/v). The fermentative capacity of the yeast (expressed as maximum specific rate of sugar consumption) remained the same at all sugar concentrations in unsupplemented mashes, but decreased in yeast extract-supplemented mashes at sugar concentrations below 33% (w/v). When the sugar concentration was above 33% sugar (w/v), the fermentative capacity in yeast extract-supplemented mashes was greater than that observed in unsupplemented samples.     

Determination of submicrogram-per-liter concentrations of caffeine in surface water and groundwater samples by solid-phase extraction and liquid chromatography

A method for determining submicrogram-per-liter concentrations of caffeine in surface water and groundwater samples has been developed. Caffeine is extracted from a 1 L water sample with a 0.5 g graphitized carbon-based solid-phase cartridge, eluted with methylene chloride-methanol (80 + 20, v/v), and analyzed by liquid chromatography with photodiode-array detection. The single-operator method detection limit for organic-free water samples was 0.02 microgram/L. Mean recoveries and relative standard deviations were 93 +/- 13% for organic-free water samples fortified at 0.04 microgram/L and 84 +/- 4% for laboratory reagent spikes fortified at 0.5 microgram/L. Environmental concentrations of caffeine ranged from 0.003 to 1.44 micrograms/L in surface water samples and from 0.01 to 0.08 microgram/L in groundwater samples.     

Effect of ionic strength on the self-assembly, morphology and gelation of pH responsive β-sheet tape-forming peptides

Molecular self-assembly is an intrinsic property of proteins central to their biological functionality. One important industrially interesting property is the ability to control and switch on and off self-assembly using a variety of external chemical and physical triggers. Model peptides have been developed with significantly reduced chemical and structural complexity compared to biological proteins. These are ideal systems for exposing the fundamental principles that drive protein-like self-assembly, as well as for establishing in a quantitative manner their structure-function relationship. We investigate simple, short model peptides that adopt a purely β-strand conformation, align in an antiparallel manner and self-assemble in one dimension in solution into long β-sheet nanotapes and higher order aggregates with no other conformation (i.e., helices, turns or random coils) present in the aggregates. These micrometre-long nanostructures gel in solutions at concentrations as low as 0.2% v/v. Their gel-fluid transition has been previously shown to be controlled by pH, temperature, or by mixing with complementary peptides. Here we show the dramatic effect of another chemical trigger, that of physiological-like salt concentration, on the self-assembly, morphology and gelation of a series of systematically designed charged self-assembling tape-forming peptides, each 11 amino acid residues in length, in the pH range of 2-14. This study provides a detailed understanding of the self-assembly of this class of peptides in aqueous solutions of biologically relevant pH and ionic strength. This insight has led to the development of injectable self-assembling peptide lubricants as potential therapeutics for the treatment of early stage knee joint osteoarthritis.     

Linker Vacancy Engineering of a Robust ftw-type Zr-MOF for Hexane Isomers Separation

Discrimination of physically similar molecules by porous solids represents an important yet challenging task in industrially relevant chemical separations. Precisely controlled pore dimension and/or tailored pore surface functionality are crucial to achieve high-efficiency separation. Metal-organic frameworks (MOFs) are promising candidates for these challenging separations in light of their structural diversity as well as highly adjustable pore dimension/functionality. We report here a microporous, ftw -type Zr-based MOF structure, HIAM-410 (HIAM=Hoffmann Institute of Advanced Materials), built on hexanuclear Zr₆ cluster and pyrene-1,3,6,8-tetracarboxylate (ptc⁴⁻). Its crystallographic structure has been determined using continuous rotation electron diffraction (cRED) technique combined with Rietveld refinement against powder X-ray diffraction data, aided by low-dose high-resolution transmission electron microscopy (HRTEM) imaging. The compound features exceptional framework stability that is comparable to the prototype MOF UiO-66. Interestingly, the linker vacancies in the pristine MOF structure could be partially restored by post-synthetic linker insertion. Its separation capability of hexane isomers is enhanced substantially upon the linker vacancy engineering. The restored structure exhibits efficient splitting of monobranched and dibranched hexane isomers at both room temperature and industrially relevant temperature.     

Olive mill wastewater treatment by a pilot-scale subsurface horizontal flow (SSF-h) constructed wetland

Performances of a pilot-scale reed bed for the olive mill wastewater (OMW) treatment were investigated, by monitoring influent and effluent pH, total suspended solids (TSS), chemical oxygen demand (COD), total Kjeldahl nitrogen (TKN), total phosphorus and polyphenols. In order to reduce the suspended matter concentration and to avoid clogging, OMW was pre-treated by adding lime putty, calcium hydroxide and hydraulic lime. The best results were obtained with 2 g/L of hydraulic lime. Pre-treated OMW was dosed in the reed bed at dilution ratios of 1/3 and 1/10 (v/v), pointing up that the latter only did not give rise to reed suffering and allowed to obtain good and durable removal efficiencies, above all for COD (74.1+/-17.6%) and polyphenols (83.4+/-17.8%). Recycling of the effluent was quite effective for the improvement of the wastewater quality, allowing a further removal of 26-70%, depending on the parameter taken into account. A post-dosage study, carried out by feeding the reed bed with the effluent of an activated sludge plant, pointed up a rapid decreasing of the outlet concentrations of the investigated parameters to values compatible with Italian regulations concerning wastewater discharge in surface water. Polyphenols were the exception, being their outlet concentration at the end of post-dosage study around 2 mg/L.     

Speciation analysis of mercury and lead in fish samples using liquid chromatography-inductively coupled plasma mass spectrometry

A liquid chromatography-inductively coupled plasma mass spectrometric (LC-ICP-MS) method for lead and mercury speciation analysis was described. Sample containing ionic lead and mercury compounds was subjected to liquid chromatographic separation before injection into the direct injection high efficiency nebulizer (DIHEN, 170-AA). The species studied include inorganic lead (Pb(II)), trimethyl lead (trimethyl-Pb), triethyl lead (triethyl-Pb), inorganic mercury (Hg(II)), methyl mercury (methyl-Hg) and ethyl mercury (ethyl-Hg), which were well separated by reversed-phase liquid chromatography with a C18 column as the stationary phase and a pH 2.8 solution of 0.2% (v/v) 2-mercaptoethanol, 1 mg L(-1) ETDA, 174.2 mg L(-1) sodium 1-pentanesulfonate and 12% (v/v) methanol as the mobile phase. The lead and mercury species in biological tissues were quantitatively extracted, into 10 g L(-1) EDTA and 0.2% (v/v) 2-mercaptoethanol solution taken in a closed centrifuge tube and kept on water bath, using microwaves at 65 degrees C for 2 min. The spike recovery of individual lead and mercury species determined by spiking the samples with suitable concentration of lead and mercury mixture standard were between 93% and 99%. The detection limits of the species studied were in the range 0.1-0.3 microg Pb L(-1) and 0.2-0.3 microg Hg L(-1). The procedure has been applied for the speciation analysis of two reference samples namely NRCC DOLT-3 Dogfish Liver and DORM-2 Dogfish Muscle and a swordfish sample obtained locally. The sum of the concentrations of individual species has been compared with the certified values for total lead and mercury to verify the accuracy of the method. The precision between sample replicates was better than 10% with LC-DIHEN-ICP-MS method.     

Evidence of complete hydrophobic coating of bombesin by trifluoroethanol in aqueous solution: an NMR spectroscopic and molecular dynamics study

Bombesin is a tetradecapeptide that possesses a random coil structure in pure water. In the presence of 30 % (v/v) 2,2,2-trifluoroethanol (TFE), it adopts a partial helical conformation involving the C-terminal amino acids 6-14. This conformational change, known as the TFE effect, is studied here in terms of the solvation state of the peptide at different TFE concentrations by means of intermolecular homo- and heteronuclear NOE measurements. When an aqueous solution of bombesin is titrated with TFE, a continual decrease in the water/peptide interactions and a concomitant increase in the TFE/peptide interactions is observed, and at 30 % (v/v) TFE no homonuclear NOEs between water and the peptide can be detected. The conformational transition of the bombesin molecule is thus accompanied by a complete surface covering with TFE. A parallel molecular dynamics (MD) study of the peptide in aqueous solution with the single-point charge (SPC) water model and in a 30 % (v/v) TFE/water mixture with a recently developed TFE model has also been performed. The 10 ns simulations were in agreement with the experimental data. The calculations indicate stabilisation of the alpha-helix in the H(2)O/TFE mixture, in contrast to the situation in pure water, and clustering of the TFE molecules around the peptide.     

Spectrophotometric study of the solubility and the protolytic properties of 1-(2-pyridylazo)-2-naphthol in different ethanol–water solutions

The solubility and the protolytic constants of 1-(2-pyridylazo)-2-naphthol (PAN) have been accurately determined at temperatures between 20.0 and 30.0°C in ethanol–water solutions with ethanol concentrations ranging from 10.0% to 95.0% (v/v). The measurement of the protolytic constants is based on the spectrophotometric determination of the concentrations of the corresponding conjugate acid–base pairs in ethanol–water solutions containing PAN and hydrochloric acid or sodium hydroxide. The traditionally used pH measurements in such studies in non-aqueous solutions are thus avoided. The solubility and the protolytic constants of PAN in pure water have been calculated by extrapolating the ethanol–water results to pure water where PAN is practically insoluble. The determination of the thermodynamic data mentioned above is necessary for elucidating the interactions of PAN with various metal ions in solutions and in cation-exchange membranes (e.g., Nafion^®) used as PAN-based optodes.     

Oilfield solids and water-in-oil emulsion stability

Model water-in-hydrocarbon emulsions consisting of toluene, heptane, water, asphaltenes, and native solids were used to investigate the role of native solids in the stability of oilfield emulsions. The solids were recovered from an oil-sands bitumen, a wellhead emulsion, and a refinery slop oil. The solids were clay platelets and fell into two size categories: (1) fine solids 50 to 500 nm in diameter and (2) coarse solids 1 to 10 microm in diameter. Emulsions stabilized by fine solids and asphaltenes were most stable at a 2:1 fractional area ratio of asphaltenes to solids. It appears that when the asphaltene surface coverage is high, insufficient solids remain to make an effective barrier. When the solids coverage is high, insufficient asphaltenes remain on the interface to immobilize the solids. Treatments that weaken the interface, such as toluene dilution, are recommended for emulsions stabilized by fine solids. Emulsions stabilized by coarse solids were unstable at low solids concentrations but became very stable at solids concentrations greater than 10 kg/m(3). At low concentrations, these solids may act as bridges between water droplets and promote coalescence. At high concentrations, layers of coarse solids may become trapped between water droplets and prevent coalescence. Treatments that flocculate the solids, such as heptane dilution, are recommended for emulsions stabilized by high concentrations of coarse solids. It is possible that emulsions containing both types of solids may require more than one treatment, or even process step, for effective water resolution.     

Determining Yields in High Solids Enzymatic Hydrolysis of Biomass

As technologies for utilizing biomass for fuel and chemical production continue to improve, enzymatic hydrolysis can be run at still higher solids concentrations. For hydrolyses that initially contain little or no free water (10-40% total solids, w/w), the saccharification of insoluble polymers into soluble sugars involves changes of volume, density, and proportion of insoluble solids. This poses a new challenge when determining the degree of hydrolysis (conversion yield). Experiments have shown that calculating the yield from the resulting sugar concentration in the supernatant of the slurry and using the assumed initial volume leads to significant overestimations of the yield. By measuring the proportion of insoluble solids in the slurry as well as the sugar concentration and specific gravity of the aqueous phase, it is possible to precisely calculate the degree of conversion. The discrepancies between the different ways of calculating yields are demonstrated along with a nonlaborious method for approximating yields in high solids hydrolysis.     

超高效液相色谱-串联质谱法检测麦汁和啤酒中的麦香风味物质

应用超高效液相色谱-串联质谱(UPLC-MS/MS)技术定量检测了啤酒和麦汁中的2,5-二甲基-4-羟基-3(2H)-呋喃酮(DMHF)、2(或5)-乙基-5(或2)-甲基-4-羟基-3(2H)-呋喃酮(EMHF)和2-乙酰吡咯(2-AP)3种麦香风味物质。使用C₁₈固相萃取柱净化样品。采用ACQUITY UPLC HSS T3色谱柱(50 mm×2.1 mm, 1.8 μm)分离,以0.1%(v/v)甲酸水溶液和0.01%(v/v)甲酸乙腈溶液为流动相进行梯度洗脱。结合这3种化合物的保留时间,在正离子模式下,采用多反应监测(MRM)技术进行定量检测。当质量浓度低于1000 μ g/L时,校准曲线的线性良好(R²>0.999)。方法的加标回收率在74.3%~86.7%之间,相对标准偏差(RSD,n=6)在4.8%~7.3%之间。由于酵母发酵时会生成DMHF和EMHF,导致啤酒中这两种物质的含量明显高于麦汁。某些品类啤酒如印度淡色爱尔啤酒(IPA),通常含有较高的麦香风味物质。该法样品处理简单,选择性好,且灵敏、准确、重现性好,可用于啤酒生产的过程控制。     

Chemical stability of haloperidol injection by high performance thin-layer chromatography

The chemical stability of haloperidol lactate injection was studied under different storage conditions by high performance thin-layer chromatography (HPTLC). The study was performed at 25 +/- 2 degrees C and at refrigeration temperature (8 +/- 1 degrees C) in original glass ampoules over 15 days after being opened. The samples tested at 25 +/- 2 degrees C were stored with exposure to and protection from light. Chromatographic separation was achieved on precoated silica gel F 254 HPTLC plates using a mixture of acetone/chloroform/n-butanol/glacial acetic acid/water (5:10:10:2.5:2.5, v/v/v/v/v) as a mobile phase. Quantitative analyses were carried out at a wavelength of 254 nm. The method exhibited adequate linearity (r = 0.999), selectivity, precision (RSD = 1.92%), and accuracy (recoveries from 98.59 to 101.90%). The concentrations of all samples remained greater than or 90% of the original concentration. Haloperidol lactate injection was chemically stable under all conditions studied over 15 days.     

Determination of monophosphate nucleotides by capillary electrophoresis inductively coupled plasma mass spectrometry

A preliminary study of a modified microconcentric nebulizer (CEI-100, CETAC) as the sample introduction device of capillary electrophoresis inductively coupled plasma mass spectrometry (CE-ICP-MS) for the determination of monophosphate nucleotides is described. The monophosphate nucleotides studied include adenosine 5'-monophosphate (AMP), guanosine 5'-monophosphate (GMP), uridine 5'-monophosphate (UMP) and inosine 5'-monophosphate (IMP). The species studied were well separated using a 70 cm length x 75 microm id fused silica capillary while the applied voltage was set at -22 kV and a 20 mmol l(-1) ammonium citrate/citric acid buffer (pH 4.0) containing 0.1% m/v cationic polymer (hexadimethrine bromide, Polybrene) was used as the electrophoretic buffer. The electroosmotic flow was reversed by flushing the fused silica capillary with 0.2% m/v Polybrene to accelerate separation. The detection limit of various species studied was in the range of 0.036-0.054 microg P ml(-1), which corresponded to the absolute detection limit of 1.1-1.6 pg P based on the injection volume of 30 nl. We determined the concentrations of nucleotides in two IG-enriched monosodium glutamates purchased from the local market. The recovery was in the range of 100-112% for various species, and the concentrations of IMP and GMP in these samples were in the range of 0.15-0.18% m/m.     

Liquid chromatography–tandem mass spectrometric assay for the multikinase inhibitor regorafenib in plasma

Regorafenib has recently been approved for the treatment of colorectal cancer. A bioanalytical liquid chromatography–tandem mass spectrometric assay for this multikinase inhibitor was developed and validated in plasma. The concentration range of the assay was 25–25,000 ng/mL. Protein precipitation with acetonitrile was used as sample pre‐treatment with sorafenib as internal standard. The extract was diluted with methanol (25%, v/v) and then injected onto the sub‐2 µm particle, bridged ethylsilicia hybrid trifunctional bonded C₁₈ column. Isocratic elution using 0.02% (v/v) formic acid in a methanol–water mixture was used. Compounds were monitored by a triple quadrupole mass spectrometer in the selected reaction monitoring mode after positive electrospray ionization. Double logarithmic calibration was used; within‐day precisions, between‐day precisions, and accuracies were 3.2–9.2, 4.1–12.3 and 94.8–103.0%, respectively. High drug stability was observed under all relevant storage conditions. The assay was used to measure drug concentrations in a pharmacokinetic study in wild‐type FVB mice. Copyright © 2014 John Wiley & Sons, Ltd.     

Simultaneous determination of seven pesticides in waters using multi-walled carbon nanotube SPE and NACE

In this work, NACE with UV detection is combined with SPE using multi-walled carbon nanotubes (MWCNT) as stationary phase to determine a group of seven pesticides (pirimicarb, pyrifenox, penconazol, carbendazim, cyromazine, pyrimethanil and cyprodinil) in mineral water samples using ametryn as internal standard. The optimized BGE, consisting of a mixture of MeOH and ACN (1:2 v/v) with 90 mM SDS and 20.5 mM HClO(4), was satisfactory to get a good resolution of the seven compounds in less than 13 min. On-line preconcentration was carried out by electrokinetic injection of the sample dissolved in 78:22 v/v MeOH/ACN, 1.11 mM HClO(4). Repeatability was studied for the same day (n=4), for nine different days (n=36) and for four different capillaries. RSD values were appropriate in all cases, i.e. in the range 4.3-9.4% between different capillaries. MWCNT of 10-15 nm od, 2-6 nm id and 0.1-10 mum length were used as SPE materials for the preconcentration of these pesticides from water samples. SPE parameters influencing the enrichment were optimized and the most favorable conditions were as follows: the amount of stationary phase, eluent, sample pH and sample volume were 40 mg MWCNT, 10 mL ACN and 10 mL dichloromethane containing 5% v/v formic acid, pH 8.0, and 750 mL, respectively. Mean recovery values ranged between 53 and 94% for Milli-Q water and between 47 and 93% for mineral waters (RSD values were in the range 2-16%). The method allowed the determination of these pesticides at concentrations below the maximum residue limits established by the European Union legislation (LOD in the range 27-58 ng/L). When the cost, amount and type of the carbon nanotubes used in this work are compared with those carbon nanotubes previously used in the literature it is clear that the proposed materials can be used as economical stationary phases, even cheaper than conventional SPE cartridges.     

Enhanced conversion of starch to cyclodextrins in ethanolic solutions by bacillus circulans var alkalophilus cyclomaltodextrin glucanotransferase

Improved formation of cyclodextrins (CDs) from starch in ethanolic solutions byBacillus circulans var alkalophilus cyclomaltodextrin glucanotransferase was studied. The β- and γ-CD yields increased and α-CD yield gradually decreased as the ethanol concentration was raised. The ethanol concentration required for maximal CD yield depended essentially on starch concentration. The ethanol's effect was pronounced at high starch concentrations. For example, with 30% (w/v) starch, the CD yield was 2.4-fold (146.5 g/L) in the presence of 15% (v/v) ethanol. The effect of dimethylsulfoxide on the formation of CDs was similar to that of ethanol. The disintegration of β- and γ-CDs were narrowly interdependent on the formation of a α-CD and malto-sugars. The amount of reducing sugars decreased from a dextrose equivalent value of roughly 7.5 to 4.5 in the presence of ethanol at starch concentrations 1-30% (w/v). The effect of ethanol on starchy materials from various sources was similar. It was concluded that ethanol retards the decomposition of β-CD by a general mechanism involving a decreased activity of water.     

Enzymatic hydrolysis of starch in water-immiscible organic solvent,two-phase systems

Enzyme-catalyzed hydrolyzations of starch by α-amylase have been studied in various two-phase systems, consisting of water and a water-immiscible organic solvent. The hydrolytic conversion of soluble starch to malto-oligosaccharides by α-amylase was greatly accelerated in 10% (v/v) water content of water-dodecane two-phase systems. However, a rapid inactivation of the enzyme has been observed in these systems. Addition of surfactant to these systems, such as polyoxyethylene (20) sorbitan monopalmitate (Tween 60) or bis(2-ethylhexyl) sodium sulfosuccinate (AOT), was effective for the enzyme stability. Effects of enzyme immobilization on the stability of α-amylase, using Ca-alginate and chitosan beads, also have been studied. The stability of immobilized enzyme was clearly enhanced in a 5–10% (v/v) water content two-phase system, whereas the free enzyme was inactivated within 41 h, remaining at a relative activity of 47–76% after 41 h of treatment. Furthermore, scanning electron micrographs (SEM) were taken to observe the effect of the two-phase system on the hydrolysis of starch. Potato starch granules have been extremely swelled and burst out in the stirred 10% (v/v) water content system, which did not contain enzymes.