Understanding the role of particle size on photophysical properties of CdS:Eu nanocrystals

Here, we report the role of particle size on the photoluminescence (PL) properties of CdS:Eu³⁺ nanocrystals by steady-state and time-resolved PL spectroscopy. It is found that the average decay time 〈τ〉 of undoped CdS nanocrystals increases with increasing the size. The fast component (nanosecond) is assigned due to trapping and slow component (above 10 ns) is due to defect-related emission. The decrease of fast component from 6.6 to 1.32 ns and the slow component from 20 to 14.6 ns of CdS (host) is observed in presence of Eu ions, indicating that the energy transfer occurs from CdS nanoparticles to Eu³⁺ ions. The decay time of Eu³⁺ in CdS shows two decay components (microsecond scale) and we believe that the fast component is attributed to surface-bound Eu³⁺ ions and slow component is due to lattice-bound Eu³⁺ ions. Analysis suggests that PL efficiency of Eu³⁺ ions depends on size of nanoparticles.     

Observation of green emission from Ce-doped gadolinium oxide nanoparticles

Green emission at around 500 nm is observed in Gd₂O₃:Ce³⁺ nanoparticles and the intensity is highly dependent on the concentration of Ce³⁺ in the nanoparticles. The luminescence of this emission displays both picosecond (ps) and millisecond (ms) lifetimes. The ms lifetime is over four orders of magnitude longer than typical luminescence lifetimes (10-40 ns) of Ce³⁺ in traditional Ce³⁺ doped phosphors and therefore likely originates from defect states. The picosecond lifetime is shorter than the typical Ce³⁺ value and is also likely due to defect or surface states. When the samples are annealed at 700 °C, this emission disappears possibly due to changes in the defect moieties or concentration. In addition, a blue emission at around 430 nm is observed in freshly prepared Gd₂O₃ undoped nanoparticles, which is attributed to the stabilizer, polyethylene glycol biscarboxymethyl ether. On aging, the undoped particles show similar emission to the doped particles with similar luminescence lifetimes. When Eu³⁺ ions are co-doped in Gd₂O₃:Ce nanoparticles, both the green emission and the emission at 612 nm from Eu³⁺ are observed.     

Sensitized luminescence through nanoscopic effects of ZnO encapsulated in SiO2:Tb sol gel derived phosphor

Terbium (1 mol%) doped ZnO-SiO₂ binary system was prepared by a sol-gel process. Nanoscopic effects of ZnO on the photoluminescence (PL) and the cathodoluminescence (CL) properties were studied. Defects emission from ZnO nanoparticles was measured at 560 nm and the line emission from Tb³⁺ ions in SiO₂:Tb³⁺ and ZnO-SiO₂:Tb³⁺ with a major peak at 542 nm was measured. The PL excitation wavelength for 542 nm Tb³⁺ emission was measured at ∼320 nm in both SiO₂:Tb³⁺ and ZnO-SiO₂:Tb³⁺. The CL data showed quenched luminescence of the ZnO nanoparticles at 560 nm from a composite of ZnO-SiO₂:Tb³⁺ and a subsequent increase in 542 nm emission from the Tb³⁺ ions. This suggests that energy was transferred from the ZnO nanoparticles to enhance the green emission of the Tb³⁺ ions. The PL and CL properties of ZnO-SiO₂:Tb³⁺ binary system and possible mechanism for energy transfer from the ZnO nanoparticles to Tb³⁺ ions are discussed.     

Relocalization of Ce 5d electrons from host conduction band

Single crystal fibers of Ce³⁺ doped SrAl₂O₄ and CaAl₄O₇ were prepared through the laser heated pedestal growth method. Sites dependent Ce³⁺ emissions were found at 385 nm (427 nm) and 420 nm (325 nm) in SrAl₂O₄ and CaAl₄O₇ hosts, respectively. The Ce³⁺ emissions at 385 nm and 420 nm in the two hosts exhibited strong afterglows. They could persist for more than 10 h. The long persistence and sites dependence of Ce³⁺ emissions were originated from charge compensation of doping Ce³⁺ into divalent cation sites. The lifetimes of Ce³⁺ emissions in both hosts were found to depend on the laser excitation wavelengths. With 266 nm laser excitation, Ce³⁺ 5d electrons were delocalized into the host's conduction band, resulting in a prolonged decay time. The 355 nm laser excitation did not delocalize the 5d electrons and hence the measured lifetimes were the intrinsic Ce³⁺ emission lifetimes that were 17 and 35.5 ns in SrAl₂O₄ and CaAl₄O₇ hosts, respectively. The prolonged Ce³⁺ emission lifetime on 266 nm laser excitation was because of the relocalization of the 5d electrons from the host conduction band. The lifetimes of Ce³⁺ 5d electrons within the conduction band were found to be 34 and 44 ns in SrAl₂O₄ and CaAl₄O₇ hosts, respectively.     

Luminescence studies on lanthanide ions (Eu, Dy and Tb) doped YAG:Ce nano-phosphors

Yttrium aluminum garnet nanoparticles both undoped and doped with lanthanide ions (Ce³⁺, Eu³⁺, Dy³⁺ and Tb³⁺) having average size around 30 (±3 nm) nm were prepared by glycine nitrate combustion method followed by annealing at a relatively low temperature of 800 °C. Increase in the annealing temperature has been found to improve the luminescence intensity and for 1200 °C heated samples there exists strong energy transfer from Tb³⁺ to Ce³⁺ ions in YAG:Ce(2%),Tb(2%) nanoparticles as revealed by luminescence studies. Co-doping the YAG:Ce nanoparticles with Eu³⁺ results in significant decrease in the emission intensity of both Ce³⁺ and Eu³⁺ ions and this has been attributed to the oxidation of Ce³⁺ to Ce⁴⁺ and reduction of Eu³⁺ to Eu²⁺ ions. Dy³⁺ co-doping did not have any effect on the Ce³⁺ emission as there is no energy transfer between Dy³⁺ and Ce³⁺ ions.     

Dyand Mn emission in KMgSO4Cl phosphor

In the present paper, KMgSO₄Cl:Ce³⁺, KMgSO₄Cl:Ce³⁺,Dy³⁺, and KMgSO₄Cl:Ce³⁺,Mn²⁺, new halosulphate phosphors were synthesized by wet chemical method. X-ray powder diffraction (XRD) and photoluminescence (PL) characterization of phosphors have been reported in this paper. The effects of Dy³⁺ co-doping on the PL characteristics of KMgSO₄Cl:Ce phosphor were studied. Energy transfer from Ce³⁺→Dy³⁺and Ce³⁺→Mn²⁺ results in increase in PL peak intensity suggesting that Ce³⁺ plays an important role in PL emission in the present matrix. The PL emission spectra have two peaks (482 and 571 nm) and a single peak (564 nm), which could be attributed to the Ce³⁺→Dy³⁺and Ce³⁺→Mn²⁺ emissions, respectively.     

Synthesis and luminescence investigation of RE (Eu, Tb and Ce)-doped lithium silicate (Li2SiO3)

Synthesis and photoluminescence (PL) investigations of lithium metasilicate doped with Eu³⁺, Tb³⁺ and Ce³⁺ were carried out. PL spectra of Eu-doped sample showed peaks corresponding to the ⁵D₀→⁷F_j (j=1, 2, 3 and 4) transitions under ultraviolet excitation. Strong red emission coming from the hypersensitive ⁵D₀→⁷F₂ transition of Eu³⁺ ion suggested the presence of the dopant ion in structurally disordered environment. Tb³⁺-doped silicate sample showed blue-green emission corresponding to the ⁵D₄→⁷F_j (j=6, 5 and 4) transitions. Ce-doped sample under excitation from UV, showed a broad emission band in the region 350-370 nm with shoulders around 410 nm. The fluorescence lifetimes of Eu³⁺ and Tb³⁺ ions were found out to be 790 and 600 μs, respectively. For Ce³⁺, the lifetime was of the order of 45 ns. PL spectra of the europium- and terbium-doped samples were compared with commercial red (Y₂O₃:Eu³⁺) and green (LaPO₄:Tb³⁺) phosphors, respectively. It was found that the emission from the doped silicate sample was 37% of the commercial phosphor in case of the Tb-doped sample and 8% of the commercial phosphor in case of the Eu-doped sample.     

Solvothermal synthesis and luminescent properties of YAG:Tb nano-sized phosphors

Nano-sized Tb-doped YAG phosphor particles were synthesized by a mixed solvo-thermal method using stoichiometric amounts of inorganic aluminum and yttrium salts. The formation of YAG:Tb was investigated by means of XRD and IR spectra. The pure crystalline-phase YAG was prepared under moderate synthesis conditions (300 °C and 10 MPa), indicating that ethanol partly replaces water as the solvent, thus favoring the formation of YAG. TEM images showed that YAG:Tb phosphor particles sintered at 300 °C were basically of spherical shape, with good dispersion about a particle size of around 80 nm. The crystalline YAG:Tb showed green emission with ⁵D₄−⁷F₆ (544 nm) as the most prominent group. The PL intensity and crystallinity of YAG:Tb phosphors increases with increasing synthesis temperature, and reaches maximum brightness at 300 °C, which is lower than that exhibited by a commercial product.     

Synthesis and photoluminescence of CeO2:Eu phosphor powders

The crystalline structure and photoluminescence (PL) properties of europium-doped cerium dioxide synthesized by the solid-state reaction method were analyzed. CeO₂:Eu³⁺ phosphor powders exhibit the pure cubic fluorite phase up to 10 mol% doping concentration of Eu³⁺. With indirect excitation of CeO₂ host at 373 nm, the PL intensity quickly increases with increasing Eu³⁺ concentration, up to about 1 mol%, and then decreases indicating the concentration quenching. While with direct excitation (467 nm), much more stronger PL emissions, especially the electric dipole emission ⁵D₀-⁷F₂ at 612 nm, are observed and no concentration quenching occurs up to 10 mol% doping concentration of Eu³⁺. The nature of this behavior and the cause of the concentration quenching were discussed.     

Structural,morphological and photoluminescence characteristics of sol-gel derived nano phase CeO<Subscript>2</Subscript> films deposited using citric acid

Homogenous nano structured CeO₂ films have been prepared by a sol-gel process using different mole ratios of citric acid as additive. XPS studies clearly illustrate an increase in Ce³⁺ proportion upon the use of higher citric acid content for the deposition of films. The crystallite sizes in the films lie in the nanorange. Photoluminescence emission in the films is attributed to various defects resulting from crystallization. Lowest transparency, high Ce³⁺ content and optimum sized crystallites in CeO₂ (1:1.5) films have led to its highest PL characteristics. Ce³⁺ chemical state is the major contributor to the PL activity of these films. The SEM micrographs show a reduced level of CeO₂ agglomeration in the films deposited using higher citric acid contents. A comparison of different properties of CeO₂ films deposited using citric acid and CeO₂–TiO₂ films has also been made.      

Energy transfer in Y3Al5O12:Ce, Pr and CaMoO4:Sm, Eu phosphors

Non-radiative energy transfers (ET) from Ce³⁺ to Pr³⁺ in Y₃Al₅O₁₂:Ce³⁺, Pr³⁺ and from Sm³⁺ to Eu³⁺ in CaMoO₄:Sm³⁺, Eu³⁺ are studied based on photoluminescence spectroscopy and fluorescence decay patterns. The result indicates an electric dipole-dipole interaction that governs ET in the LED phosphors. For Ce³⁺ concentration of 0.01 in YAG:Ce³⁺, Pr³⁺, the rate constant and critical distance are evaluated to be 4.5×10⁻³⁶ cm⁶ s⁻¹ and 0.81 nm, respectively. An increase in the red emission line of Pr³⁺ relative to the yellow emission band of Ce³⁺, on increasing Ce³⁺ concentration is observed. This behavior is attributed to the increase of spectral overlap integrals between Ce³⁺ emission and Pr³⁺ excitation due to the fact that the yellow band shifts to the red spectral side with increasing Ce³⁺ concentration. In CaMoO₄:Sm³⁺, Eu³⁺, Sm³⁺-Eu³⁺ transfer occurs from ⁴G_5/2 of Sm³⁺ to ⁵D₀ of Eu³⁺. The rate constant of 8.5×10⁻⁴⁰ cm⁶ s⁻¹ and the critical transfer distance of 0.89 nm are evaluated.     

Enhanced luminescent properties of Y3Al5O12:Tb,Ce phosphor prepared by spray pyrolysis

Yttrium aluminum garnet (YAG) particles doped with Tb³⁺ or double doped with Tb³⁺ and Ce³⁺ were prepared by spray pyrolysis and characterized by photo- and cathode-luminescence. It was tried to incorporate a broad band of Ce³⁺ activator into the line peaks of Tb³⁺ in YAG host without the reduction of emission intensity. Ce-codoped YAG:Tb particles showed a broad band emission due to the d-f transition of Ce³⁺ and a reduction in the intensity of emission peaks due to ⁵D₃-⁷F_j (j=3, 4, 5, 6) transition of Tb³⁺ when they were excited by the ultraviolet light of 270 nm. These results supported that an effective energy transfer occurs from Tb³⁺ to Ce³⁺ in YAG host. Codoping Ce³⁺ ions greatly intensified the excitation peak at 270 nm for the emission at 540 nm of Tb³⁺, which means that more lattice defects, involving in the energy absorption and transfer to Tb³⁺, are formed by the Ce³⁺ codoping. The finding gives a promising approach for enhancing the luminescence efficiency.     

Enhanced emission of Er from alternately Er doped Si-rich Al2O3 multilayer film with Si nanocrystals as broadband sensitizers

Alternately Er doped Si-rich Al₂O₃ (Er:SRA) multilayer film, consisting of alternate Er-Si-codoped Al₂O₃ (Er:Si:Al₂O₃) and Si-doped Al₂O₃ (Si:Al₂O₃) sublayers, has been synthesized by co-sputtering from separated Er, Si, and Al₂O₃ targets. The dependence of Er³⁺ related photoluminescence (PL) properties on annealing temperatures over 700-1100 °C was studied. The maximum intensity of Er³⁺ PL, about 10 times higher than that of the monolayer film, was obtained from the multilayer film annealed at 950 °C. The enhancement of Er³⁺ PL intensity is attributed to the energy transfer from the silicon nanocrystals in the Si:Al₂O₃ sublayers to the neighboring Er³⁺ ions in the Er:Si:Al₂O₃ sublayers. The PL intensity exhibits a nonmonotonic temperature dependence: with increasing temperature, the integrated intensity almost remains constant from 14 to 50 K, then reaches maximum at 225 K, and slightly increases again at higher temperatures. Meanwhile, the PL integrated intensity at room temperature is about 30% higher than that at 14 K.     

Efficient fluorescence of dissolved CaF2:Tb and CaF2:Ce, Tb nanoparticles through surface coating sensitization

Oleic acid (OA)-modified CaF₂:Tb³⁺ nanoparticles with various Tb³⁺ concentrations and CaF₂:Ce³⁺, Tb³⁺ nanoparticles were synthesized. The as-prepared nanoparticles were shown to be well dissolved in some common organic solvents, such as chloroform and toluene. The nanoparticles were characterized by Fourier transform infrared spectroscopy (FT-IR), X-Ray diffraction (XRD) and transmission electron microscopy (TEM). The investigation of fluorescence properties of CaF₂:Tb³⁺ nanoparticles showed that the Tb³⁺ ions could be sensitized efficiently by the surface coating of OA and CaF₂:Tb³⁺ nanoparticles with 10 mol% Tb³⁺ concentrations possess the highest emission intensity. The comparison of emission for CaF₂:Ce³⁺, Tb³⁺ and CaF₂:Tb³⁺ (10 mol%) nanoparticles revealed that the emission intensity of the former is about 4.5 times as strong as that of the latter.     

Energy transfer from benzoic acid to lanthanide ions in benzoic acid-functionalized lanthanide-doped CaF2 nanoparticles

The preparation of benzoic acid-functionalized CaF₂:Ln³⁺ (Ln = Eu or Tb) nanoparticles and their sensitized luminescence are described in this report. First, to achieve sufficient proof for energy transfer from benzoic acid (BA) to lanthanide ions doped in nanoparticles, we employ Eu³⁺ as the microscopic probe and investigate the luminescent spectra of benzoic acid-functionalized CaF₂:Eu³⁺ (BA-CaF₂:Eu³⁺) nanoparticles. Next, to further reveal the difference between sensitized luminescence and common luminescence for Eu³⁺ doped in CaF₂ nanoparticles, we study the emission spectra of BA-CaF₂:Eu³⁺ nanoparticles excited at 286 nm and 397 nm, respectively. Finally, we analyze and compare the luminescent spectra of BA-CaF₂:Tb³⁺ and CaF₂:Ce³⁺, Tb³⁺ nanoparticles in detail. Our results indicate that both Eu³⁺ and Tb³⁺ doped in CaF₂ nanoparticles can be efficiently sensitized through benzoic acid.     

Comparative investigation on spectroscopic properties of Er between Ce-doped and B2O3-added bismuth glasses

The comparative investigation on the spectroscopic properties of Er³⁺ in low phonon energy Bi₂O₃-GeO₂-Ga₂O₃-Na₂O glasses codoped with Ce³⁺ ion and added with B₂O₃ component, respectively, is presented. With increasing Ce₂O₃ content from 0 to 0.8 mol% or B₂O₃ content from 0 to 15 mol%, the lifetime of Er³⁺:⁴I_11/2 level decreases dramatically from 607 to 283 μs or to 197 μs, and the upconversion fluorescence is quenched in both glass samples. The nonradiative energy transfer from Er³⁺:⁴I_11/2→Ce³⁺:²F_5/2 or the enhanced multiphonon relaxation process together with the energy transfer between Er³⁺ and OH⁻ groups are, respectively, responsible for the results. Meanwhile, the lifetime of ⁴I_13/2 level remains almost unchanged in Er³⁺/Ce³⁺-codoped glasses whereas it decreases rapidly in B₂O₃-added cases. As a result, Er³⁺/Ce³⁺ codoping improves the 1.5 μm fluorescence emission intensity, however, B₂O₃ addition has a negative effect on it. The research results indicate that the Er³⁺/Ce³⁺-codoped bismuth glasses will be preferable for obtaining efficient 980 nm pumped EDFA.     

Temperature-dependent photoluminescence properties of (Y, Lu)3Al5O12:Ce phosphors for white LEDs applications

The effects of the excitation wavelength, Ce³⁺ concentration and chemical substitution on the thermal quenching of Y₃Al₅O₁₂:Ce³⁺ (YAG:Ce³⁺) phosphors were investigated over a temperature range from 30 to 250 °C. The quenching behavior exhibits a complex dependence on the excitation wavelength and Ce³⁺ concentration, which can be attributed to temperature-dependent absorption strength of the different f-d absorption bands and thermally activated concentration quenching with or without energy migrations between Ce³⁺ ions, respectively. With increasing Lu³⁺content the luminescence of (Y, Lu)₃Al₅O₁₂:Ce³⁺ phosphors shows a pronounced blueshift, and simultaneously the temperature quenching is obviously improved due to a decrease in Stokes shift.     

Scintillation and anomalous emission in elpasolite Cs2LiLuCl6:Ce

The luminescence and scintillation properties of Cs₂LiLuCl₆:0.5%Ce³⁺ are presented. Special attention is devoted to a 9.4 ns fast emission at 275 nm that can only be excited via the highest cubic field 5d_e state of Ce. Contrary to Cs₃LuCl₆ and Cs₂LiYCl₆, where the same type of fast emission was observed, the emission in Cs₂LiLuCl₆ is still observed at room temperature. Assuming that the 5d_e state is located inside the host conduction band (CB), we propose that the emission originates from a mixed state at or just below the bottom of the CB and ends at the 4f ground state of Ce³⁺. To proof this model we studied the thermal quenching of the anomalous luminescence and performed X-ray photoelectron spectroscopy. A model for a temperature-activated energy transfer from the anomalous state to the lowest 5d_t excited state of Ce³⁺ explains most of the results. Besides the 275 nm emission, the material shows 5d_t-4f Ce³⁺ emission at 370 and 406 nm and 2 ns fast core-valence luminescence when excited with 16-22 eV photons. The scintillation properties of Cs₂LiLuCl₆:Ce are briefly discussed.     

Passively Q-switched diode-pumped Cr:YAG/Nd:GdVO4 monolithic microchip laser

The realization of high repetition rate passively Q-switched monolithic microlaser is a challenge since a decade. To achieve this goal, we report here on the first passively Q-switched diode-pumped microchip laser based on the association of a Nd:GdVO₄ crystal and a Cr⁴⁺:YAG saturable absorber. The monolithic design consists of 1 mm long 1% doped Nd:GdVO₄ optically contacted on a 0.4 mm long Cr⁴⁺:YAG leading to a plano-plano cavity. A repetition rate as high as 85 kHz is achieved. The average output power is approximately 400 mW for 2.2 W of absorbed pump power and the pulse length is 1.1 ns.     

Temperature-dependent photoluminescence spectra of Er-Tm-codoped Al2O3 thin film

Er-Tm-codoped Al₂O₃ thin films with different Tm to Er concentration ratios were synthesized by cosputtering from separated Er, Tm, Si, and Al₂O₃ targets. The temperature dependence of photoluminescence (PL) spectra was studied. A flat and broad emission band was achieved in the 1.4-1.7 μm and the observed 1470, 1533 and 1800 nm emission bands were attributed to the transitions of Tm³⁺: ³H₄ → ³F₄, Er³⁺: ⁴I_13/2 → ⁴I_15/2 and Tm³⁺: ³F₄ → ³H₆, respectively. The temperature dependence is rather complicated. With increasing measuring temperature, the peak intensity related to Er³⁺ ions increases by a factor of five, while the Tm³⁺ PL intensity at 1800 nm decreases by one order of magnitude. This phenomenon is attributed to a complicated energy transfer (ET) processes involving both Er³⁺ and Tm³⁺ and increase of phonon-assisted ET rate with temperature as well. It should be helpful to fully understand ET processes between Er and Tm and achieve flat and broad emission band at different operating temperatures.