The influence of Pr co-doping on the luminescent properties of Lu2O3:5 mol% Eu films

Uniform and crack free polycrystalline lutetium oxide (Lu₂O₃:(Eu,Pr)) films were fabricated by Pechini sol-gel method combined with the spin-coating technique. X-ray diffraction (XRD) and atomic force microscope (AFM) characterizations indicated that the obtained film was composed of polycrystalline cubic Lu₂O₃ phase with an average grain size around 30 nm. The photoluminescence(PL) spectra and decay performances of the Lu₂O₃:5 mol% Eu films co-doped by 0-0.5 mol% Pr³⁺ with different concentrations were characterized. It was found that the afterglow was reduced obviously due to the introduction of 0-0.5 mol% Pr³⁺ in the Lu₂O₃:5 mol% Eu films coupled by decrease in the emission intensity at 612 nm. The mechanism of afterglow diminishing was discussed based on the thermoluminescence measurements.     

Luminescence in trivalent rare earth activated Sr4Al2O7 phosphor

In this paper we report the combustion synthesis of trivalent rare-earth (RE³⁺ = Dy, Eu and Ce) activated Sr₄Al₂O₇ phosphor. The prepared phosphors were characterized by the X-ray powder diffraction (XRD) and photoluminescence (PL) techniques. Photoluminescence emission peaks of Sr₄Al₂O₇:Dy³⁺ phosphor at 474 nm and 578 nm in the blue and yellow region of the spectrum. The prepared Eu³⁺ doped phosphors were excited by 395 nm then we found that the characteristics emission of europium ions at 615 nm (⁵D₀?⁷F₂) and 592 nm (⁵D₀?⁷F₁). Photoluminescence (PL) peaks situated at wavelengths of 363 and 378 nm in the UV region under excitation at around 326 nm in the Sr₄Al₂O₇:Ce³⁺ phosphor.     

Novel green-emitting Na2CaPO4F:Eu phosphors for near-ultraviolet white light-emitting diodes

In this study, green-emitting Na₂CaPO₄F:Eu²⁺ phosphors were synthesized by solid-state reactions. The excitation spectra of the phosphors showed a broad hump between 250 and 450 nm; the spectra match well with the near-ultraviolet (NUV) emission spectra of light-emitting diodes (LEDs). The emission spectrum showed an intense broad emission band centered at 506 nm. White LEDs were fabricated by integrating a 390 nm NUV chip comprising blue-emitting BaMgAl₁₀O₁₇:Eu²⁺, green-emitting Na₂CaPO₄F:0.02 Eu²⁺, and red-emitting CaAlSiN₃:Eu²⁺ phosphors into a single package; the white LEDs exhibited white light with a correlated color temperature of 5540 K, a color-rendering index of 90.75, and color coordinates (0.332, 0.365) close to those of ideal white light.     

Synthesis of Y2Si2O7:Eu nanocrystal and its optical properties

Nanocrystalline Y₂Si₂O₇:Eu phosphor with an average size about 60 nm is easily prepared using silica aerogel as raw material under ultrasonic irradiation and annealing temperature at 300-600 °C and this nanocrystalline decomposes into Y₂O₃:Eu and silica by heat treatment at 700-900 °C. The excitation broad band centered at 283 and 254 nm results from Eu³⁺ substituting for Y³⁺ in Y₂Si₂O₇ and Y₂O₃/SiO₂, respectively. Compared with Y₂O₃:Eu/SiO₂ crystalline, the PL excitation and emission peaks of Y₂Si₂O₇:Eu nanocrystalline red-shift and lead to the enhance of its luminescence intensity due to the different chemical surroundings of Eu³⁺ in above nanocrystallines. The decrease of PL intensity may be ascribed to quenching effect resulting from more defects in Y₂O₃:Eu/SiO₂ crystalline.     

Enhanced blue emission and EPR study of LaMgAl11O19:Eu phosphors

Europium doped LaMgAl₁₁O₁₉ phosphor was prepared by the combustion method. The as-prepared and post-treated (1350 °C 10 h 5% H₂+95% N₂) phosphors were investigated by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), scanning electron microscopy (SEM), photoluminescence (PL) and electron paramagnetic resonance (EPR) techniques. XRD patterns show that LaMgAl₁₁O₁₉:Eu phosphors have hexagonal structure. FT-IR spectrum exhibits absorption bands corresponding to the stretching vibration of AlO₄ and AlO₆. Morphological studies reveal that this phosphor has faceted plates of varying sizes and shapes. The as-prepared LaMgAl₁₁O₁₉:Eu phosphor consists of both Eu³⁺ and Eu²⁺ ions. The phosphor exhibits a bright blue emission at 450 nm (4f⁶5d→4f⁷ transition of Eu²⁺). On post-treating the phosphor we are able to enhance the blue emission efficiency by 330%. The process was detected from the evolution of excitation, emission and EPR spectra and the results are discussed.     

Multiplication of electronic excitations in nanophosphors Lu2O3:Eu and Lu2O3:Tb

Luminescence properties of Lu₂O₃:Eu³⁺ and Lu₂O₃:Tb³⁺ nanocrystalline powders with the particle size varying from 46 to 6 nm were studied under excitation by synchrotron radiation in the photon energy range (up to ∼22.5 eV) covering the region where the processes of multiplication of electronic excitation occur. It was found that the excitation spectra of Tb³⁺ emission from all Lu₂O₃:Tb³⁺ nanopowders have similar behavior, whereas the shape of the excitation spectra of Eu³⁺ emission from Lu₂O₃:Eu³⁺ nanopowders strongly depends on the particle size. The difference in the behavior of Lu₂O₃:Eu³⁺ and Lu₂O₃:Tb³⁺ nanophosphor systems was explained by different mechanisms of the energy transfer from the host to Eu³⁺ or Tb³⁺ ions (either the hole or electron recombination mechanism, respectively), which are differently influenced by losses of electronic excitations near the particle surface.     

Phosphorescent and thermoluminescent properties of SrAl2O4:Eu,Dy phosphors prepared by solid state reaction method

Long persistent SrAl₂O₄:Eu²⁺ phosphors co-doped with Dy³⁺ were prepared by the solid state reaction method. The main diffraction peaks of the monoclinic structure of SrAl₂O₄ were observed in all the samples. The broad band emission spectra at 497 nm for SrAl₂O₄:Eu²⁺, Dy³⁺ were observed and the emission is attributed to the 4f⁶5d¹ to 4f⁷ transition of Eu²⁺ ions. The samples annealed at 1100–1200 °C showed similar broad TL glow curves centered at 120 °C. The similar TL glow curves suggest that the traps responsible for them are similar. The long afterglow displayed by the phosphors annealed at different temperatures, may be attributed to the Dy³⁺ ions acting as the hole trap levels, which play an important role in prolonging the duration of luminescence.     

Sol-gel growth of Gd2MoO6:Eu nanocrystalline layers on SiO2 spheres (SiO2@Gd2MoO6:Eu) and their luminescent properties

SiO₂@Gd₂MoO₆:Eu³⁺ core-shell phosphors were prepared by the sol-gel process. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectra (EDS), transmission electron microscopy (TEM), photoluminescence (PL) spectra as well as kinetic decays were used to characterize the resulting SiO₂@Gd₂MoO₆:Eu³⁺ core-shell phosphors. The XRD results demonstrate that the Gd₂MoO₆:Eu³⁺ layers on the SiO₂ spheres begin to crystallize after annealing at 600 °C and the crystallinity increases with raising the annealing temperature. The obtained core-shell phosphors have a near perfect spherical shape with narrow size distribution (average size ca. 600 nm), are not agglomerated, and have a smooth surface. The thickness of the Gd₂MoO₆:Eu³⁺ shells on the SiO₂ cores could be easily tailored by varying the number of deposition cycles (50 nm for four deposition cycles). The Eu³⁺ shows a strong PL luminescence (dominated by ⁵D₀-⁷F₂ red emission at 613 nm) under the excitation of 307 nm UV light. The PL intensity of Eu³⁺ increases with increasing the annealing temperature and the number of coating cycles.     

Effect of concentration on the luminescence of Eu ions in nanocrystalline La2O3

Nanocrystalline powders with various Eu³⁺ concentration (from 1 to 10 mol %) doped La₂O₃ were prepared via a combustion route. Their structure and morphology were characterized using X-ray diffraction (XRD) and High-resolution transmission electron microscopy. The emission spectra of the as-synthesized samples show that the strongest emission position is centered at 626 nm corresponding to ⁵D₀→⁷F₂ transition of Eu³⁺ ions and the intensity change of 626 nm emission is considered as a function of ultraviolet (240 nm) irradiation time. The excitation spectra at 626 nm monitoring indicate that the charge transfer state band is varies with different Eu³⁺ ion concentration. These results are attributed to the surface defects of the nanocrystals.     

Thermoluminescent and stuctural properties of BaAl2O4:Eu,Nd,Gdphosphors prepared by combustion method

BaAl₂O₄:Eu²⁺,Nd³⁺,Gd³⁺ phosphors were prepared by a combustion method at different initiating temperatures (400–1200 °C), using urea as a comburent. The powders were annealed at different temperatures in the range of 400–1100 °C for 3 h. X-ray diffraction data show that the crystallinity of the BaAl₂O₄ structure greatly improved with increasing annealing temperature. Blue-green photoluminescence, with persistent/long afterglow, was observed at 498 nm. This emission was attributed to the 4f⁶5d¹–4f⁷ transitions of Eu²⁺ ions. The phosphorescence decay curves were obtained by irradiating the samples with a 365 nm UV light. The glow curves of the as-prepared and the annealed samples were investigated in this study. The thermoluminescent (TL) glow peaks of the samples prepared at 600 °C and 1200 °C were both stable at ∼72 °C suggesting that the traps responsible for the bands were fixed at this position irrespective of annealing temperature. These bands are at a similar position, which suggests that the traps responsible for these bands are similar. The rate of decay of the sample annealed at 600 °C was faster than that of the sample prepared at 1200 °C.     

Synthesis of Gd2Ti2O7:Eu, V phosphors by sol-gel process and its luminescent properties

A red-emitting phosphor material, Gd₂Ti₂O₇:Eu³⁺, V⁴⁺, by added vanadium ions is synthesized using the sol-gel method. Phosphor characterization by high-resolution transmission electron microscopy shows that the phosphor possesses a good crystalline structure, while scanning electron microscopy reveals a uniform phosphor particle size in the range of 230-270 nm. X-ray photon electron spectrum analysis demonstrates that the V⁴⁺ ion promotes an electron dipole transition of Gd₂Ti₂O₇:Eu³⁺ phosphors, causing a new red-emitting phenomenon, and CIE value shifts to x=0.63, y=0.34 (a purer red region) from x=0.57, y=0.33 (CIE of Gd₂Ti₂O₇:Eu³⁺). The optimal composition of the novel red-emitting phosphor is about 26% of V⁴⁺ ions while the material is calcinated at 800  °C. The results of electroluminescent property of the material by field emission experiment by CNT-contained cathode agreed well with that of photoluminescent analysis.     

Luminescence studies on SrMgAl10O17:Eu, Dy phosphor crystals

Using urea as fuel, SrMgAl₁₀O₁₇:Eu, Dy phosphor was prepared by a combustion method. Its luminescence properties under ultraviolet (UV) excitation were investigated. Pure SrMgAl₁₀O₁₇ phase was formed by urea-nitrate solution combustion synthesis at 550 °C. The results indicated that the emission spectra of SrMgAl₁₀O₁₇:Eu, Dy has one main peak at 460 nm and one shoulder peak near 516 nm, which are ascribed to two different types of luminescent Eu²⁺ centers existing in the SrMgAl₁₀O₁₇ matrix crystal. The blue luminescence emission of SrMgAl₁₀O₁₇:Eu phosphors was improved under UV excitation by codoping Dy³⁺ ions. The SrMgAl₁₀O₁₇:Eu phosphors showed green afterglow (λ=516 nm) when Dy³⁺ ions were doped. Dy³⁺ ions not only successfully play the role of sensitizer for energy transfer in the system, but also act as trap levels and capture the free holes in the spinel blocks.     

Color improvement of white-light through Mn-enhancing yellow-green emission of SrSi2O2N2:Eu phosphor for white light emitting diodes

Photoluminescence (PL) enhancement of SrSi₂O₂N₂:Eu and the resultant color improvement of white-light were investigated via co-doping Mn with Eu. We observed that a unique absorption of host lattice of SrSi₂O₂N₂ and its visible band emission peaked at around ∼550 nm for SrSi₂O₂N₂:Mn²⁺ in the wavelength range of 450-600 nm. This highly eye-sensitive ∼550 nm-peaked band emission of SrSi₂O₂N₂ doped with Mn²⁺ happens to overlap the 535 nm-peaked band emission of SrSi₂O₂N₂ doped with Eu²⁺, resulting in an intensified photoluminescence in a maximum by 355%. By combining this as-prepared Mn intensified SrSi₂O₂N₂:Eu phosphor with blue InGaN chip, the quality of white-light was improved to 93.3% for color rendering index and 3584 K for correlated color temperature.     

Preparation and photoluminescence characteristics of Eu-doped MgAl1.8Y0.2O4 nanocrystals

A simple combustion route was employed for the preparation of Eu³⁺-doped MgAl_1.8Y_0.2−xO₄ nanocrystals using metal nitrates as precursors and urea as a fuel in a preheated furnace at 500 °C. The powders thus obtained were then fired at 1000 °C for 3 h to get better luminescent properties. The incorporation of Eu³⁺ activator in these nanocrystals was checked by luminescence characteristics. These nanocrystals displayed bright red color on excitation under 254 nm UV source. The main emission peak was assigned to the transition [⁵D₀→⁷F₂] at 615 nm. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) studies were carried out to understand surface morphological features and the particle size. Crystal structures of the nanocrystals were investigated by the X-ray diffraction (XRD) technique. The crystallite size of the as-prepared nanocrystals was around 29 nm, which was evaluated from the broad XRD peaks. The crystallite size increased to ∼45 nm on further heat treatment at 1000 °C.     

Synthesis and photoluminescence characteristics of (Sr, Ca)3B2O6:Eu for application in white light-emitting diodes

A series of yellow-green (Sr, Ca)₃B₂O₆:Eu phosphors have been synthesized using precursors prepared via a facile sol-gel route. The solid-solution phases crystallized to materials with the formula of Sr_3−x−yCa_xEu_yB₂O₆ with varied Ca²⁺ and Eu²⁺ contents. The emission peak centered at 540 nm under near-UV excitation exhibited a broad-band distribution in the range of 450-650 nm. The dependences of the luminescence intensity on the contents of Ca²⁺ substitution and Eu²⁺ dopant were also investigated. The composition in the host lattice sensitively affected the chromaticity index. Sr_1.21Ca_1.7Eu_0.09B₂O₆ (SCB:0.09Eu) was shown to possess the highest intensity and broadest emission band. Calcining temperature was shown to greatly influence the luminescent properties of SCB:0.09Eu. It is concluded that SCB:0.09Eu can be used as an efficient yellow-green phosphor for white light-emitting diodes (white LEDs) applications.     

Characterization of the VUV excitation spectrum of BaZr(BO3)2:Eu

The excitation spectra of M (M=Si⁴⁺, Ti⁴⁺) and Eu³⁺ co-doped BaZr(BO₃)₂, BaZrO₃:Eu and La₂Zr₂O₇:Eu in the vacuum ultraviolet (VUV) regions of 110-300 nm are investigated and the host-lattice absorption are characterized. The result indicated that BaZr(BO₃)₂:Eu³⁺ phosphor has a strong absorption under the VUV excitation, and in the host-lattice excitation, the strong band at 130-160 nm could be due to the BO₃ atomic groups; the band at 160-180 nm is related to the excitation of Ba-O; 180-200 nm corresponds to the charge transfer (CT) transition of Zr-O. The band at 200-235 nm due to the CT band of Eu³⁺-O²⁻ and a bond valence study explained the observed weak CT band of Eu³⁺-O²⁻ in the excitation spectra of BaZr(BO₃)₂:Eu³⁺. The emission results show that Si⁴⁺ can sensitize luminescence in the host of BaZr(BO₃)₂:Eu but Ti⁴⁺ has no improvement effect on luminescence.     

Luminescence studies on ZnO-P2O5 glasses doped with Gd2O3:Eu nanoparticles and Eu2O3

Zinc phosphate glasses doped with Gd₂O₃:Eu nanoparticles and Eu₂O₃ were prepared by conventional melt-quench method and characterized for their luminescence properties. Binary ZnO-P₂O₅ glass is characterized by an intrinsic defect centre emission around 324 nm. Strong energy transfer from these defect centres to Eu³⁺ ions has been observed when Eu₂O₃ is incorporated in ZnO-P₂O₅ glasses. Lack of energy transfer from these defect centres to Eu³⁺ in Gd₂O₃:Eu nanoparticles doped ZnO-P₂O₅ glass has been attributed to effective shielding of Eu³⁺ ions from the luminescence centre by Gd-O-P type of linkages, leading to an increased distance between the luminescent centre and Eu³⁺ ions. Both doped and undoped glasses have the same glass transition temperature, suggesting that the phosphate network is not significantly affected by the Gd₂O₃:Eu nanoparticles or Eu₂O₃ incorporation.     

Eu red long afterglow in Y2O2S:Ti, Eu phosphor through afterglow energy transfer

Eu,Ti co-doped Y₂O₂S:0.03Ti,0.03Eu phosphors and single Eu or Ti doped Y₂O₂S phosphors were prepared and their luminescent properties were investigated in detail by photoluminescence (PL) spectra, long afterglow spectra and thermoluminescence spectra measurements. The results showed that Y₂O₂S:Ti,Eu phosphors possess orange-red afterglow color with afterglow time above 5 h. The reddish afterglow color, which corresponds to a set of linear Eu³⁺ emissions at low-energy range (540-630 nm), was demonstrated to come from the energy transfer process from yellow Ti afterglow emissions, the proposed energy transfer mechanism may well explain the Eu³⁺ afterglow emission.     

Optical properties of (ZnO)0.5(P2O5)0.5 glasses doped with Gd2O3:Eu nanoparticles and Eu2O3

Binary (ZnO)_0.5(P₂O₅)_0.5 glasses doped with Eu₂O₃ and nanoparticles of Gd₂O₃:Eu were prepared by conventional melt-quench method and their luminescence properties were compared. Undoped (ZnO)_0.5(P₂O₅)_0.5 glass is characterized by a luminescent defect centre (similar to L-centre present in Na₂O-SiO₂ glasses) with emission around 324 nm and having an excited state lifetime of 18 ns. Such defect centres can transfer the energy to Eu³⁺ ions leading to improved Eu³⁺ luminescence from such glasses. Based on the decay curves corresponding to the ⁵D₀ level of Eu³⁺ ions in both Gd₂O₃:Eu nanoparticles incorporated as well as Eu₂O₃ incorporated glasses, a significant clustering of Eu³⁺ ions taking place with the latter sample is confirmed. From the lifetime studies of the excited state of L-centre emission from (ZnO)_0.5(P₂O₅)_0.5 glass doped with Gd₂O₃:Eu nanoparticles, it is established that there exists weak energy transfer from L-centres to Eu³⁺ ions. Poor energy transfer from the defect centres to Eu³⁺ ions in Gd₂O₃:Eu nanoparticles doped (ZnO)_0.5(P₂O₅)_0.5 glass has been attributed to effective shielding of Eu³⁺ ions from the luminescence centre by Gd-O-P type of linkages, leading to an increased distance between luminescent centre and Eu³⁺ ions.     

Highly luminescent red light phosphor CaTiO3:Eu under near-ultraviolet excitation

The Eu-doped CaTiO₃ particles with a good crystallinity were prepared via sol-gel method. The phosphors showed a strong red emission corresponding to ⁵D₀→⁷F₂ (618 nm) of Eu³⁺ under the near-ultraviolet excitation (400 nm). X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope (SEM), photoluminescent (PL) analysis and Brunauer-Emmett-Teller (BET) specific surface area measurement were utilized to characterize the CaTiO₃:Eu³⁺ particles. The concentration quenching and thermal quenching of the samples were discussed as well. The optimal concentration and the calcination temperature were 16 mol% of Eu³⁺ and 1400 °C for these phosphors, and the possible reason was discussed as well. CaTiO₃:Eu³⁺ is a promising red phosphor under near-ultraviolet excitation for various applications.