分形烟尘簇团粒子的消光特性研究

根据物质的电结构,将烟尘簇团粒子离散为一系列的偶极子,利用离散偶极子近似方法,获得了不同波长电磁波入射情况下分形烟尘簇团粒子不对称因子、吸收和散射效率因子的值.结合偶极子在电磁场中的力学性质,分析了烟尘簇团粒子在外加电磁场中所受的力和力矩,给出三种分形结构烟尘簇团粒子的电磁辐射压力及电磁辐射力矩效率因子随入射波波长变化的数值结果,分析了烟尘粒子对电磁能量吸收的宏观表现和微观机理.结果显示:入射波长、烟尘簇团粒子的分形维数及所含原始微粒数目都将影响烟尘粒子的消光特性.     

UV laser irradiation of IR laser generated particles ablated from nitrobenzyl alcohol

Particles generated by 2.94 μm pulsed IR laser ablation of liquid 3-nitrobenzyl alcohol were irradiated with a 351 nm UV laser 3.5 mm above and parallel to the sample target. The size and concentration of the ablated particles were measured with a light scattering particle sizer. The application of the UV laser resulted in a reduction in the average particle size by one-half and an increase in the total particle concentration by a factor of nine. The optimum delay between the IR and UV lasers was between 16 and 26 μs and was dependent on the fluence of the IR laser: higher fluence led to a more rapid appearance of particulate. The ejection velocity of the particle plume, as determined by the delay time corresponding to the maximum two-laser particle concentration signal, was 130 m/s at 1600 J/m² IR laser fluence and increased to 220 m/s at 2700 J/m². The emission of particles extended for several ms. The observations are consistent with a rapid phase change and emission of particulate, followed by an extended emission of particles ablated from the target surface.     

Evaluation and optimisation of phenomenological multi-step soot model for spray combustion under diesel engine-like operating conditions

In this work, a two-dimensional computational fluid dynamics study is reported of an n-heptane combustion event and the associated soot formation process in a constant volume combustion chamber. The key interest here is to evaluate the sensitivity of the chemical kinetics and submodels of a semi-empirical soot model in predicting the associated events. Numerical computation is performed using an open-source code and a chemistry coordinate mapping approach is used to expedite the calculation. A library consisting of various phenomenological multi-step soot models is constructed and integrated with the spray combustion solver. Prior to the soot modelling, combustion simulations are carried out. Numerical results show that the ignition delay times and lift-off lengths exhibit good agreement with the experimental measurements across a wide range of operating conditions, apart from those in the cases with ambient temperature lower than 850 K. The variation of the soot precursor production with respect to the change of ambient oxygen levels qualitatively agrees with that of the conceptual models when the skeletal n-heptane mechanism is integrated with a reduced pyrene chemistry. Subsequently, a comprehensive sensitivity analysis is carried out to appraise the existing soot formation and oxidation submodels. It is revealed that the soot formation is captured when the surface growth rate is calculated using a square root function of the soot specific surface area and when a pressure-dependent model constant is considered. An optimised soot model is then proposed based on the knowledge gained through this exercise. With the implementation of optimised model, the simulated soot onset and transport phenomena before reaching quasi-steady state agree reasonably well with the experimental observation. Also, variation of spatial soot distribution and soot mass produced at oxygen molar fractions ranging from 10.0 to 21.0% for both low and high density conditions are reproduced.     

烟尘中电磁波传输特性的Monte Carlo模拟

根据等效颗粒模型和分形理论,运用Mie理论和离散偶极子近似方法分别计算了烟尘簇团粒子在波长为06328?μm的电磁波入射情况下的单次散射特性.根据辐射输运理论,利用Monte Carlo方法对电磁波在烟尘中的传输特性进行数值计算,给出烟尘中反射率和透射率随入射角和烟尘厚度变化的数值结果,并分析了入射角、烟尘粒子的密度和厚度对反射率和透射率的影响.这为研究电磁波在密集分布介质中的传输特性提供了一种方法. 关键词： 烟尘粒子 离散偶极子近似 传输特性 Monte Carlo模拟     

Nanoparticle Formation by Laser Ablation

The properties of nanoparticle aerosols of size ranging from 4.9nm to 13nm, generated by laser ablation of solid surfaces are described. The experimental system consisted of a pulsed excimer laser, which irradiated a rotating target mounted in a cylindrical chamber 4cm in diameter and 18-cm long. Aerosols of oxides of aluminum, titanium, iron, niobium, tungsten and silicon were generated in an oxygen carrier gas as a result of a reactive laser ablation process. Gold and carbon aerosols were generated in nitrogen by non-reactive laser ablation. The aerosols were produced in the form of aggregates of primary particles in the nanometer size range. The aggregates were characterized using a differential mobility analyzer and electron microscopy. Aggregate mass and number concentration, electrical mobility size distribution, primary particle size distribution and fractal dimension were measured. System operating parameters including laser power (100mJ/pulse) and frequency (2Hz), and carrier gas flow rate (1l/min) were held constant.A striking result was the similarity in the properties of the aerosols. Primary particle size ranged between 4.9 and 13nm for the eight substances studied. The previous studies with flame reactors produced a wider spread in primary particle size, but the order of increasing primary particle size follows the same trend. While the solid-state diffusion coefficient probably influences the size of the aerosol in flame reactors, its effect is reduced for aerosols generated by laser ablation. It is hypothesized that the reduced effect can be explained by the collision-coalescence mechanism and the very fast quenching of the laser generated aerosol.     

Formation of noble metal particles by ultrasonic irradiation

It was found that sonochemically prepared metal particles such as Ag, Pd, Au, Pt and Rh are of nanometer size with a fairly narrow distribution (e.g., about 5 nm for Pd particles obtained from a 1.0 mM Pd(II) in polyethylene glycol monostearate solution). We have suggested three different reduction pathways under sonication: (i) reduction by H atoms, (ii) reduction by secondary reducing radicals formed by hydrogen abstraction from organic additives with OH radicals and H atoms, (iii) reduction by radicals formed from pyrolysis of the additives at the interfacial region between cavitation bubbles and the bulk solution. The reduction of Ag(I) and Pt(II) mainly proceeds through reaction pathway (ii). In the cases of Pd(II) and Au(III), the reductions mainly proceed through reaction pathway (iii). The reduction of Rh(III) was not achieved under the same conditions; however, by the addition of sodium formate, reduction occurred and the preparation of Rh particles succeeded.     

Deriving the mean primary-particle diameter and related quantities from the size distribution and the gravimetric mass of spark generated nanoparticles

Spark generated carbon and iridium nanoparticles were characterised by their electrical-mobility diameter D and by the mass of particulate matter collected in parallel on filter. The particles exhibited slightly skewed lognormal size distributions with mean mobility diameters between 18 and 74 nm. The masses calculated from the measured distributions under the assumption that the particles were spherical (diameter D) and of bulk mass density turned out to be much higher than the gravimetric mass, by factors between 8 and as high as 340. This very pronounced difference initiated a search for an improved relation between particle size and mass. Data analysis suggested that the mass increases linearly with increasing D. Hence the measured distributions were evaluated under the assumption that the spark generated matter was composed of spherical primary nanoparticles of mean diameter d, aggregated in the form of chains of joint length βD, with β>1. Using reasonable values of β between 2 and 4, the mean diameter of carbon primary particles turned out to be 10±1.8 nm, in excellent agreement with size data recently obtained by transmission electron microscopy (TEM). The primary iridium particles were found to be distinctly smaller, with diameters between 3.5±0.6 nm and 5.4±0.9 nm. The comparatively small uncertainty is due to the fact that the primary-particle diameter is proportional to the square root of β. The calculated volume specific surface areas range between 500 and 1700 m²/cm³. These numbers are close to the ‘active’ surface areas previously measured by the BET method. The good agreement with TEM and BET data suggests that the novel approach of nanoparticle characterisation is meaningful. Accordingly, the number concentrations of all individual primary particles rather than the concentrations measured by the mobility analyser should be␣considered the correct dose metric in studies on animal exposure to spark generated nanoparticles. The␣evaluated data imply that the numbers quoted in the literature must be enlarged by factors ranging between about 10 and a maximum as high as 80. An erratum to this article can be found at     

Measurement of stress waves in polymers generated by UV laser ablation

Propagation of stress waves into polymer substrates undergoing UV laser ablation has been studied by means of laser Doppler vibrometry technique. The measurements acquired far from the ablation point demonstrate oscillations of high amplitude and low decay. For all the studied samples, realized in polystyrene and polymethylmethacrylate of two different molecular weights, ablation generates mechanical excitation of the structure, which propagates all over the bulk as vibrational modes and stress waves.     

Micro-lens arrays generated by UV laser irradiation of doped PMMA

Micro-lenses with well-defined optical parameters are generated on polymethylmethacrylate (PMMA) substrates doped with diphenyltriazene (DPT) by controlled use of a swelling effect generated under conditions of subablative excimer laser illumination. The surface profiles depend on the laser spot size and energy density. A sensitively balanced combination of matrix softening, substrate volume expansion due to photochemical nitrogen release, and surface tension is responsible for the final shape of the lenses. Complete arrays of identical lenses with 15 μm diameters and a focal length of 30 μm are produced by irradiation of (0.25 wt. %) DPT-PMMA with a single laser pulse at a wavelength of 308 nm and a fluence of 3 J/cm². It is shown experimentally and theoretically that appropriate volume expansion is possible without introducing internal light scattering due to the formation of small bubbles. Received: 7 April 1999 / Accepted: 8 April 1999 / Published online: 5 May 1999     

Investigation of mass and energy coupling between soot particles and gas species in modelling ethylene counterflow diffusion flames

A numerical model is developed aiming at investigating soot formation in ethylene counterflow diffusion flames. The mass and energy coupling between soot solid particles and gas-phase species is investigated in detail. A semi-empirical two-equation model is chosen for predicting soot mass fraction and number density. The model describes particle nucleation, surface growth, and oxidation. A detailed kinetic mechanism is considered for the gas phase and the effect of considering radiation heat losses is also evaluated. Simulations were done for a range of conditions that produce low-to-significant amounts of soot using three strategies: first by changing the strain rate imposed on the flow field, second, by changing the oxygen content in the oxidant stream, and third, by changing the pressure. Additionally, the effect of the transport model chosen was analysed. The results showed that, for the flames studied and within the limits of the present work, the soot and gas radiation terms are of primary importance for numerical simulations. Additionally, it was shown that the soot mass and thermodynamic properties coupling terms are, in general, a second-order effect, with an importance that increases as soot amount increases. As a general recommendation, the radiation terms have always to be considered, whereas full coupling has to be employed only when the soot mass fraction, Y_S, is equal to or larger than 0.008. If a higher precision is required, with errors less than 1%, full coupling should be taken into account for Y_S ≥ 0.002. For lower soot amounts, the coupling through soot mass and thermodynamic properties may be neglected as a first approximation, but an error on the total mass conservation will be present. Additionally, discrepancies from considering different transport models (detailed or simplified) are larger than those found from not fully coupling the phases.     

Dynamics of radiation scattering by particles of condensed phase in quasicontinuous laser irradiation of metals

Radiation scattering by particles of condensed phase in an ablation plasma plume has been experimentally studied during quasicontinuous laser irradiation (λ = 1.06 μm, q = 0.1–9 MW/cm², τ ∼ 1.5 msec) of duraluminum D16T, aluminum A99, and bismuth. The particle size distribution and the nature of their dispersal during irradiation was studied in scattered light (λ = 0.69 μm) from individual particles that could be visually observed on photographs. It was found that under the pressure developed in the plume, large particles ejected from the irradiated zone can move backward and return to the target (D16T). The plume (Bi) becomes brighter due to ablation of particles in the path of the laser beam. The directional scattering coefficients for scattering from the local zone on the axis of the plume, measured during the laser pulse, were used to study the relationship between the dynamics of entry of condensed phase into the plume, shielding of the target by the particles, and brightening of the plume under the action of the incident laser radiation. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 73, No. 2, pp. 210–219, March–April, 2006.     

Catalytic soot oxidation in microscale experiments: Simulation of interactions between co-deposited graphitic nanoparticle agglomerates and platinum nanoparticles

Continuously regenerating catalytic soot traps are under development to reduce particulate emissions from diesel exhaust. A good understanding of the processes that take place during soot oxidation is needed to optimize diesel soot trap performance. To gain insight into these processes from the perspective of nanoparticle technology, the effects of catalyst particle size and the interparticle distance between soot and catalyst particles were measured. A model catalyst was prepared by depositing Pt nanoparticles on a SiO/SiO₂-coated transmission electron microscope (TEM) grid. A soot surrogate composed of graphitic nanoparticle agglomerates generated by laser ablation was deposited on the same surface. This system simulates, morphologically, catalytic soot traps used in practice. The reaction was carried out in a tubular flow reactor in which the gas phase simulated diesel exhaust gas, composed of a mixture of 10% O₂ and 1000 ppm NO with the remainder N₂. The progress of the carbon nanoparticle oxidation was monitored off-line by analysis of electron microscopy images of the agglomerates before and after reaction. This experimental method permitted the correlation of reaction rate with particle sizes and separation distances as well as catalyst surface area in the direct environs of the soot particles. The experimental results revealed no effect of Pt catalyst particle size in the range 7–31 nm on the rate of reaction. Also observed were a decrease in the rate of reaction with increasing distance between carbon agglomerates and catalyst particles and a linear dependence of the reaction rate on the fractional catalyst surface area coverage.     

Raman spectroscopy of carbonaceous particles of environmental interest

Carbonaceous particles of environmental origin are practically insoluble, which constitutes an obstacle to many chemical physical characterization techniques. Micro‐Raman spectroscopy overcomes the sample preparation step and can be applied on the as‐received sample and even in situ, with nowadays commercially available portable Raman equipment. Multivariate statistical analysis of Raman data recorded on a variety of carbonaceous particles of different origin, through a molecular interpretation of the signal, shows that the use of Raman spectroscopy with several excitation sources can provide a useful tool for assisting the characterization of various forms of environmental carbon matter. Copyright © 2015 John Wiley & Sons, Ltd.     

Enhancement of ablation rate and production of colloidal nanoparticles by irradiation of metals with nanosecond pulsed laser in presence of external electric field

This paper presents the results of experimental study on the effect of electric field on the ablation rate during the nanosecond pulsed laser ablation of aluminum and copper in deionized water. The effect of electric field strength on the material removal rate and its mechanisms were investigated both in the electric field parallel and perpendicular to the laser beam path schemes. The ablation rate was estimated by measuring the dimensions of craters on the target induced by laser. The crater dimensions and optical properties of the produced colloidal nanoparticles were characterized by means of optical microscopy and UV–Vis absorption spectroscopy, respectively. The results indicate that pulsed laser ablation in the presence of an electric field significantly leads to higher material removal rate. The experimental results also confirm that the crater geometry extremely depends on the direction of the electric field with respect to the laser beam direction. The UV–Vis spectra show that the nanoparticles production efficiency increases with increasing the electric field strength.     

斜入射激光支持燃烧波时纵波声场的指向性

利用理论推导及实验验证的方法研究了激光倾斜入射支持燃烧波时纵波声场的指向性。根据激光超声的产生机理, 在喷溅物质垂直作用于工件表面的前提条件下, 推导了椭圆形声源作用时远场质点的法向位移。获得了纵波声场的指向性函数, 分析了影响纵波声场指向性的因素, 并进行了实验验证。利用功率密度低于爆轰波点燃阈值的激光烧蚀工件, 使用峰值频率为5 MHz压电探头接收纵波, 进而获得纵波声场的指向性实验数据, 结果表明, 实验数据与理论数据能够较好地进行吻合。在光斑短轴长度恒定时, 与激光垂直入射相比, 各倾斜入射角度下纵波声场的声束轴线指向均保持不变, 并且指向性图形随倾斜角度的增加而变得细窄, 纵波声场的能量也更加集中。     

Synthesis of PMA stabilized silver nanoparticles by chemical reduction process under a two-step UV irradiation

Poly(methacrylic acid) (PMA) stabilized silver nanoparticles (Ag NPs), also used in the surface modification of clothing fibers, were fabricated via chemical reduction processes under UV irradiation. To obtain an uniform size distribution it has been designed a new “two-step” process which employs two different UV radiation densities in order to control the kinetics of NPs nucleation. The as produced nanoparticles were characterized by UV-vis absorption spectroscopy and TEM microscopy. The results show the reduction of the Ag ions and the nanoparticles nucleation in the first step. In the second step, the final Ag NPs size distribution is controlled through a quick cross-linking of the PMA that freezes out any further modification. A narrow size distribution with more than 80% NPs smaller than 10 nm and none larger than 25 nm was obtained and the long-term stability (one month) of the colloidal solution was verified.     

Silver nanoparticles generated by pulsed laser ablation in supercritical CO2 medium

Pulsed laser ablation (PLA) has been widely employed in industrial and biological applications and in other fields. The environmental conditions in which PLA is conducted are important parameters that affect both the solid particle cloud and the deposition produced by the plume. In this work, the generation of nanoparticles (NPs) has been developed by performing PLA of silver (Ag) plates in a supercritical CO₂ medium. Ag NPs were successfully generated by allowing the selective generation of clusters. Laser ablation was performed with an excitation wavelength of 532 nm under various pressures and temperatures of CO₂ medium. On the basis of the experimental result, both surface of the irradiated Ag plate and structure of Ag NPs were significantly affected by the changes in supercritical CO₂ pressure and temperature. With increasing irradiation pressure, plume deposited in the surrounding crater created by the ablation was clearly observed. In Field Emission Scanning Electron Microscopy (FE-SEM) the image of the generated Ag NPs on the silicon wafer and the morphology of Ag particles were basically a sphere-like structure. Ag particles contain NPs with large-varied diameter ranging from 5 nm to 1.2 μm. The bigger Ag NPs melted during the ablation process and then ejected smaller spherical Ag NPs, which formed nanoclusters attached on the molten Ag NPs. The smaller Ag NPs were also formed around the bigger Ag NPs. Based on the results, this new method can also be used to obtain advanced nano-structured materials.     

Ar环境下脉冲激光烧蚀粒子阻尼系数的空间分布

在10 Pa的Ar环境气体中,采用脉冲激光烧蚀技术,分别在半径为2.0,2.5,3.0,3.5和4.0 cm的半圆环不同角度处的衬底上制备了一系列含有纳米晶粒的Si晶薄膜。使用扫描电子显微镜、X射线衍射仪和拉曼光谱仪对其表面形貌和微观结构进行分析表征。结果表明,纳米Si晶粒的平均尺寸和烧蚀粒子的阻尼系数均相对于羽辉轴向呈对称分布,并随着与羽辉轴向夹角的增大而减小;同时,随着衬底半径的增加,晶粒平均尺寸和阻尼系数均逐渐减小。     

Selfassembly of Metallic Nanoparticle Arrays by DNA Scaffolding

We report the self-assembly of metallic nanoparticle arrays using DNA crystals as a programmable molecular scaffolding. Gold nanoparticles, 1.4nm in diameter, are assembled in two-dimensional arrays with interparticle spacings of 4 and 64nm. The nanoparticles form precisely integrated components, which are covalently bonded to the DNA scaffolding. These results show that heterologous chemical systems can be assembled into precise, programmable geometrical arrangements by DNA scaffolding, thereby representing a critical step toward the realization of DNA nanotechnology.