壁面加热湍流相干结构的实验研究

用热线风速仪测量了风洞中壁面加热平板湍流边界层不同法向位置的流向脉动速度,用条件采样方法中的m-u-level法和VITA法研究了壁面加热对壁湍流相干结构猝发条件平均波形的影响,发现壁面另热能够提高猝发强度,缩短喷射时间,使一次猝发中出现多次喷射事件的现象明显增多,增强猝发的间歇性。     

柔性壁面湍流减阻机理与多尺度相干结构控制的实验研究

用热膜测速仪以高于对应最小湍流时间尺度的分辨率,精细测量了水槽中刚性壁面和柔性壁面平板湍流边界层不同法向位置流向速度分量的时间序列信号,利用湍流边界层近壁区域的对数律平均速度剖面与壁面摩擦速度、流体粘性系数、壁面摩擦切应力等内尺度物理量的关系,在准确测量湍流边界层近壁区域对数律平均速度剖面的基础上,通过非线性迭代求解壁面摩擦速度以及湍流边界层壁面摩擦切应力.结果表明柔性壁的湍流边界层速度分布在对数律层有所上移,缓冲层增厚,说明柔性壁面具有一定的减阻作用. 利用湍流多尺度局部平均结构函数的概念和多尺度局部平均结构函数的瞬时强度因子、平坦因子检测多尺度相干结构及其间歇性的方法,提取了湍流边界层多尺度相干结构的条件相位平均波形.对比研究了刚性壁面和柔性壁面平板湍流边界层近壁区域多尺度相干结构的条件相位平均波形及其间歇性的统计特征,分析了柔性壁面具有减阻作用的物理机理.     

湍流边界层空间特征尺度的层析TRPIV测量

利用层析TRPIV测量得到的平板湍流边界层三维三分量速度场数据库,计算得到了平板湍流边界层空间耗散尺度、剪切尺度、泰勒微分尺度、积分尺度等典型空间特征尺度分别为3～5,40～100,20～50,4000个壁面单位,发现耗散尺度随法向位置缓慢增加,剪切尺度在靠近壁面的区域随法向位置变化不明显,积分尺度已不随法向位置变化....     

壁湍流温度扩展的自相似性及其层次结构模型

用热线风速仪测量了风洞中壁面加热平板湍流边界层不同法向位置的温度信号,研究了温度结构函数扩展的自相似性及其层次结构模型与湍流平均流场的非均匀性的关系。     

壁面湍流发卡涡包空间模态的TRPIV实验研究

运用高时间分辨率粒子图像测速(Time-resolved PIV简称TRPIV),测量得到平板湍流边界层流向/法向平面内瞬时速度矢量空间分布的时间序列;采用空间局部平均速度结构函数的概念,识别和提取湍流边界层中大尺度发卡涡包结构的空间特征。发现在湍流边界层中不同法向位置多个正负发卡涡包结构同时交替存在。这些分布在不同法向高度的发卡涡包结构之间通过倾斜的涡量剪切层相联系,构成了湍流边界层中内、外区紧密相连、相互作用的一种稳态的分布方式。     

壁湍流相干结构的教学实验(八)─—用数字滤波法检测壁湍流相干结构

通过用三丝热膜探针测量湍流边界层的三个速度分量对壁湍流相干结构进行了实验研究，介绍了检测壁湍流相干结构的数字滤波法．     

基于PIV技术分析颗粒在湍流边界层中的行为

采用粒子图像测速技术(particle image velocimetry,PIV)在平板湍流边界层内开展实验研究,对比颗粒相及单相液体的平均速度剖面、湍流强度、雷诺应力等湍流统计量,分析颗粒在湍流边界层中的行为.利用空间多尺度局部平均涡量的概念提取壁湍流发卡涡展向涡头(顺向涡)并统计其数量规律,得到不同法向位置处顺向涡周围流向脉动速度及流线的空间拓扑结构,比较分析顺向涡发展程度及周围的湍流相干结构.结果发现:与清水工况相比,颗粒相湍流边界层的缓冲层变薄、对数律区下移,湍流强度得到增强,雷诺应力在对数律区有所增大;颗粒的流向脉动速度在展向涡周围的分布与清水工况不同,颗粒能够被流体展向涡周围的猝发过程有效传递;颗粒相的顺向涡涡核较大,且随着法向位置的升高逐渐发展完整,涡和条带在流向上拉伸得更长;同时发现在两种工况下,顺向涡的左下方始终存在一个逆向涡,颗粒相逆向涡的形成弱于单相流体;两种工况下的顺向涡数量均随着法向位置的升高而减少,最后逐渐趋于稳定.      

壁面加热边界条件对湍流扩展的自相似性的影响

用热线风速仪测量了风洞中壁面加热和不加热平板湍流边界层不同法向位置的瞬时流向速度的时间序列,研究了壁面加热的边界条件对流向速度增量的p阶结构函数的扩展的自相似性和层次结构模型的影响。实验结果表明,壁面加热的边界条件对流向速度增量的结构函数扩展的自相似标度律的相对标度指数δ（p,3）和层次结构模型中间歇参数β、最奇异指数γ的影响明显存在。     

低湍流度风洞中湍流度对平板边界层转捩影响的试验研究

本文报告了在西北工业大学壁低流度风洞中进行了平板边界层转捩试验研究的简况及初步结果，试验湍流度为０．０２％、０．１％及０．３３％，用恒温热线风速仪测量时均速度型，求得边界层沿流向的位移厚度分布，并用示波器观察速度脉动脉形变化，从而确定起始转捩点和完全转捩点位置。结果表明，转捩的规律性和国外经典结果极为吻合。     

输气管道壁面涂料减阻机理的实验研究

用IFA-300热线风速仪以高于对应最小湍流时间尺度的分辨率精细测量了风洞中不同壁面涂料的管道湍流边界层不同法向位置流向速度分量的时间序列信号,利用湍流边界层近壁区域对数律平均速度剖面与壁面摩擦速度、流体黏性系数等内尺度物理量的关系和壁面摩擦速度与壁面摩擦切应力的关系,在准确测量湍流边界层近壁区域对数律平均速度剖面的基础上,间接测量湍流边界层的壁面摩擦阻力．对不同壁面涂料的壁湍流脉动速度信号用子波分析进行多尺度分解,用子波系数的瞬时强度因子和平坦因子检测管道湍流边界层中的多尺度相干结构,提取不同尺度相干结构的条件相位平均波形,对比研究输气管道壁面涂料的减阻机理．     

The two-dimensional velocity shift caused by the use of a rotating mirror in PIV flow field measurements

A theoretical analysis of the two-dimensional velocity shift by the use of a rotating mirror in PIV flow field measurements has been carried out by the application of ray optics. The velocity shift has been calculated directly in the flow field co-ordinates. In dimensionless form the results are also available in the image plane. It is shown that the distribution of the velocity shift over the entire observation field may not usually be assumed to be uniform (and may vary by up to 20%). The effect of the layout and arrangement of the rotating mirror on the velocity shift and its distribution has been analysed. In addition, the sensitivity of the velocity shift to the design tolerances and imperfections of the rotating mirror is given.     

Effect of loosely bonded undulated boundary surfaces of doubly layered half-space on the propagation of torsional wave

This paper investigates the propagation of torsional wave in an initially stressed poroelastic layer with corrugated as well as loosely bonded boundary surfaces, sandwiched between a corrugated fiber-reinforced layer and a viscoelastic half-space under initial stress. The velocity equation has been obtained in closed form analytically and the substantial effect of affecting parameters on the phase velocity of torsional surface wave has been demonstrated numerically and graphically. Comparative study has been made to observe the effect of flatness parameter, reinforcement, viscoelasticity and porosity on the phase velocity, meticulously. Some particular cases have also been discussed and it is found that velocity equation is in well-agreement to the classical Love wave equation. Moreover, some remarkable observation has been made through numerical computation and graphical demonstration for fiber-reinforced layer of carbon fiber-epoxy resin, poroelastic layer of sandstone and a viscoelastic half-space.     

Study of a plane‐free jet exhausting from a channel by vortex‐in‐cell method

A two‐dimensional simulation of a plane jet exhausting from a channel has been performed using the vortex in cell algorithm in the Reynolds number range of 100–900. The vorticity is generated on the wall of the entrance channel whose length has been fixed in order to obtain a fully developed velocity profile at the entry of the jet. The transient behaviour of the velocity field starting from rest has been observed until reaching a quasi steady regime. The mean value of the velocity field is compared with the results of a finite volume computation on the same mesh. The velocity fluctuations obtained using this method are analysed. Their effect on the mean flow is estimated to be smaller than the viscous effect. Copyright © 2006 John Wiley & Sons, Ltd.     

Particle separation from a four-particle-system

The paper deals with the effects of particle separation from a plane four-particle system. First, the process of particle separation, which is done with certain velocity, has been studied. Then, the motion of the remainder three-particle system with initial conditions which correspond to the velocity and angular velocity after particle separation has been investigated. Further, the attraction and resistance forces between particles have been considered and the influence of the damping force and the friction force have been analyzed as well. Thus, the final position of the particles and the geometrical configuration directly dependent on the certain velocity of the separated particle is obtained.     

应用单色光的三维激光测速系统

本文发展了一种采用单色激光器的三维激光测速系统。四束入射光布置成等腰直角三角形,用一个前透镜聚焦。这种光学布置光能利用率高,并能适用于近壁处流速测量。当实验模型具有多层不同性质介面时,入射光仍能保持相交。为了分离三维速度分量,采用了频率分离和偏振分离技术。特别考虑了光轴分量的测量精度,提出了提高测量精度的一些方法。应用此系统测量了斜切尾钝体后部的三维平均速度和湍流度分布。     

Finite Element Solution of Mixed Convection on a Moving Vertical Cylinder with Suction in a Moving Micropolar Fluid Medium

In this paper the problem of mixed convection on a moving vertical cylinder with suction in a moving micropolar fluid medium has been investigated, using finite element method. The effect of important parameters, namely micropolar parameter, suction parameter and velocity coefficient parameter have been discussed on the velocity, microrotation and temperature functions when the velocity of the cylinder is greater than the free stream velocity. Skin friction and the Nusselt number have also been computed, which are given in the table. The temperature distribution is effected moderately by the motion of the cylinder as well with the buoyancy parameter.     

Three-dimensional flow pattern visualization and bubble size distributions in stationary and transient upward flashing flow

For the first time, an experimental three-dimensional reconstruction and visualization of stationary and transient flashing flow in a vertical pipe (47 mm diameter) is presented. The measurements have been performed by means of wire-mesh sensors. This type of sensor delivers two-dimensional void-fraction distributions in the pipe cross-section where it is mounted with a maximum sampling rate of 10,000 frames per second. A sampling rate of 1200 frames per second has been used in this work. Steam bubbles have been identified from the wire-mesh data and their complete three-dimensional reconstruction has been performed by taking into account the steam bubble velocity. For the estimation of the bubble velocity, two wire-mesh sensors positioned at a small axial distance from each other have been used. The velocity has been determined by cross-correlation of the two wire-mesh signals, by direct identification of the traveling time of the steam bubbles between the two sensors and by means of a drift-flux model. A comparison between the three methods of bubbles velocity measurement is reported. Stationary and time-dependent bubble size distributions have been derived. The stationary radial void-fraction profiles have been decomposed according to bubble size classes and compared with the results obtained with an equilibrium model.     

Bifurcation analysis of an electro-statically actuated micro-beam in the presence of centrifugal forces

In this paper, the influence of centrifugal forces on the stability of an electro-statically actuated clamped–clamped micro-beam has been investigated. The non-dimensional governing static and dynamic equations have been linearized using the step by step linearization method (SSLM), then, a Galerkin-based reduced order model has been used to solve the linearized equations. For constant value of a bias DC voltage and different values of angular velocity the equilibrium points of the corresponding autonomous system including stable center points, unstable saddle points and singular points have been obtained using the equivalent mass-spring model. Subsequently the bifurcation diagram has been depicted using the obtained fixed point. The static pull-in voltage value for different values of angular velocity and the static pull-in angular velocity for different values of bias voltage have been calculated. The obtained results are validated using results of previous studies and a good agreement has been observed. The effect of the centrifugal force on the fixed points has been studied using the phase portraits of the system for different initial conditions. Moreover, the effects of centrifugal forces on the dynamic pull-in behavior have been investigated using time histories and phase portraits for different angular velocities.     

爆炸膨胀环一维应力假定的分析与讨论

对爆炸膨胀环的运动过程和应力状态进行了理论分析,指出膨胀环在径向变形过程中其厚度减小 将引起内外壁的速度差,对膨胀环内外壁的速度差进行了分析。由于膨胀环内外壁速度差的存在必然造成复 杂应力状态,无法满足一维应力假定,由此推断出实验中利用外壁速度计算出的应力要略大于膨胀环内的平 均应力。利用LS-DYNA三维动力学有限元程序验证了理论分析结果,利用膨胀环外壁速度计算出的应力比 数值模拟给出的膨胀环内平均应力大1%左右。     

Impingement of a low Reynolds number turbulent circular jet onto a flat plate at normal incidence

The velocity field of a circular water jet impinging onto a flat plate has been measured using particle image velocimetry, or PIV. The velocity field has been recorded at several instants in time, producing thousands of simultaneous two-dimensional velocity measurements for each realization. The instantaneous velocity, vorticity and rate-of-strain fields reveal the interaction of vortices near the impinging wall within the radial wall jet downstream from the stagnation point. An ensemble average of the instantaneous fields produces a mean velocity field of the jet flow, which reveals many of the processes leading to boundary layer separation and vortex breakaway within the wall jet. The PIV system extracts the velocity measurements using a two-dimensional autocorrelation method, and can obtain thousands of highly accurate velocity measurements within a few minutes. The structure found in these experiments may be similar to the ground level structure of atmospheric microburst phenomena.A version of this paper was presented at the 11th Symposium on Turbulence, University of Missouri-Rolla, 17–19 October 1988