紫外光照射二氧化钛纳米管沉积纳米金颗粒应用于染料敏化太阳电池

通过紫外光照射成功把金粒子沉积到二氧化钛纳米管的管壁中。通过扫描电镜、能谱和X射线衍射进行表征。沉积所得的金粒子为高度分散的纳米级粒子,并且金颗粒的粒径和密度可通过沉积时间控制。应用于染料敏化太阳电池中,由于金颗粒存在表面等离子增强效应,可提高电池的光电转换效率。然而随着沉积时间增长,沉积的金颗粒粒径会增大,所得电池的效率将会下降。     

ITO/TiO2表面电沉积CdS纳米粒子及其薄膜的光电性能

采用阴极恒电位沉积方法, 在TiO2表面沉积制备出CdS纳米粒子. XRD和SEM测试结果表明, CdS粒子的结构以六方晶相为主, 粒径分布均匀, 表面形貌呈菜花状. 通过调节沉积电位和沉积时间等因素在一定程度上可以控制CdS纳米粒子的生长. 随着沉积电位变负, CdS粒子的粒径逐渐减小. 沉积时间越短, 粒子粒径越小. 紫外-可见吸收光谱测试结果表明, 不同条件下制备出来的CdS粒子表现出一定的量子尺寸效应. 此外, 沉积条件也会影响ITO/TiO2/CdS复合半导体薄膜的光电性能.     

悬浮液进样电感藕合等离子体发射光谱中颗粒的输运和蒸发行为

以碳化硼为例,研究了悬浮液雾化进样中的粒子在传输和蒸发过程中的行为,并对分析结果出现负偏离的原因进行了详细探讨.对比悬浮液颗粒的原始粒径分布和经过传输过程后的粒径分布,获得到达等离子体的颗粒粒径上限小于10 Am.样品中存在的部分超大粒径的颗粒(d>>10 μm)会严重影响可传输区域颗粒(d<10 μm)的质量运输效率...     

藤茶干粉提取液还原制备金纳米粒子

用藤茶干粉提取液生物还原氯金酸溶液实现了金纳米粒子绿色制备,通过紫外-可见分光光度计、透射电子显微镜和粒度分布等技术手段对金纳米粒子形态等物性进行了表征,运用控制变量法探究了金纳米粒子生物合成的规律。研究发现,金纳米粒子的粒径、粒径分布、形状和稳定性受反应体系pH值、温度以及氯金酸的用量影响。pH6.47或藤茶干粉提取液过量时会引起纳米金的团聚;温度升高,金纳米粒子平均粒径会减小。通过变量控制,可以实现金纳米粒子绿色合成的有效控制。     

电化学沉积法制备金（核）-铜（壳）纳米粒子阵列

以组装在有机分子自组装膜/金基底电极上的Au纳米粒子阵列为电化学沉积模板,制备了金(核)-铜 (壳)纳米粒子阵列.选用巯基十一胺（AUDT）和巯基癸烷（DT）混合自组装膜作为基底电极与Au纳米粒子的耦联层,可以在一定的电位下实现金属Cu在Au纳米粒子上的选择性沉积.将沉积电位控制在－0.03 V（vs SCE）时,沉积初期（t ≤ 15 s,沉积粒子粒径 ≤ 20 nm ）金(核)-铜 (壳)粒子具有良好的单分散性和近似球形,而且粒径实验值同计算值非常吻合.     

山竹果壳提取液中金纳米粒子的生物合成及光谱性质研究

在山竹果壳提取液中,以山竹多酚既作还原剂又作保护剂,制备了具有高度稳定性、单分散性的亲水性金纳米粒子。利用紫外可见分光光度法、透射电子显微镜和X射线衍射等手段对制备的金纳米粒子进行了表征和分析。结果表明:金纳米粒子的尺寸大小在9~23nm范围,升高温度其还原反应速率加快,所得金纳米粒子的尺寸减小、单分散性提高。山竹多酚保护金的金纳米颗粒具有pH值调控的分散可逆性。降低山竹提取液的浓度可得到包括单晶纳米片在内的多形态金纳米颗粒。     

TiO_2微球的合成及其作为散射层在量子点敏化太阳能电池中的应用（英文）

以十六烷基三甲基溴化铵(CTAB)为模板剂,通过TiCl4在乙醇水溶液中的直接水解,制备了介孔TiO2微球.X射线衍射(XRD)结果表明所制备的微球晶型为金红石,扫描电镜(SEM)结果显示微球的直径大约为700nm,由粒径约为16 nm的小颗粒堆积而成.通过刮涂法制备了在TiO2小颗粒层上涂覆有作为散射层的TiO2微球和未涂覆微球的薄膜.并通过化学浴沉积(CBD)的方法在膜上生长CdS/CdSe量子点,得到了量子点敏化太阳能电池(QDSCs).紫外吸收和漫反射结果表明,这种微球结构有利于量子点的沉积,具有较强的光散射作用,有效地增加了光线的收集,从而提高了电池的光电流,最终得到了4.5%的光电转换效率,比不加散射层的电池的效率高27.7%,也比利用传统散射层(由20 nm TiO2小颗粒和400 nm TiO2固体颗粒组成)的电池效率高10.2%.我们把电池效率的提升归因于较强的光散射作用和较长的电子寿命.     

低温静电自组装法制备贵金属修饰TiO_2纳米结构薄膜及其增强的光催化性能(英文)

以碱-水热法在金属Ti片上原位生长了TiO2纳米结构(纳米花和纳米线)薄膜,并采用低温静电自组装方法将超细贵金属(金、铂、钯)纳米颗粒均匀沉积于多孔TiO2薄膜上.负载于Ti片上的贵金属/TiO2纳米结构薄膜具有一体化结构、多孔架构和高光催化活性.超高分辨率场发射扫描电子显微镜(FESEM)直接观察表明贵金属纳米颗粒在TiO2表面分布均匀,且颗粒之间相互分离,金、铂、钯纳米颗粒的平均粒径分别约为4.0、2.0和10.0nm.俄歇电子能谱(AES)纵深成分分析表明贵金属不仅沉积于薄膜表面,且大量分布于TiO2纳米结构薄膜内部,其深度超过580 nm.X射线光电子能谱(XPS)分析表明,经300°C下在空气中热处理后,纳米金仍保持金属态,纳米铂部分被氧化成PtOabs,而钯粒子则完全被氧化成氧化钯(PdO).以低温静电自组装法沉积贵金属,贵金属负载量可通过调节组装时间与溶胶pH值来控制.光催化降解甲基橙的结果表明,沉积的纳米金和铂能显著增加TiO2纳米结构薄膜的光催化活性,说明金和铂粒子可促进光生载流子的分离;但负载的PdO对TiO2薄膜的光催化性能增强几乎无作用.     

金纳米粒子的微波法合成及在蛋白质检测中的应用

通过对微波反应器中氯金酸和柠檬酸钠混合物进行直接加热,快速、一步合成了金纳米粒子.通过调节反应初始混合物中氯金酸与柠檬酸钠的比例,可获得不同粒径窄分散的金纳米粒子.进一步将所合成的金纳米粒子功能化,考察了其在蛋白质检测中的应用.     

银包覆金纳米粒子膜的制备、表征及其SERS效应

本文研究了通过液相微波高压技术和自组装方法相结合制备的复合纳米粒子膜。首先, 将利用微波加热制备的金纳米粒子组装到石英片上,然后,再通过微波加热方法在石英片上的金颗粒表面沉积生长银包裹层, 用UV-Vis吸收光谱和原子力显微镜对该结构的复合纳米粒子膜进行表征。研究表明：通过在微波高压反应中调节银的沉积量可以有效控制包覆层的厚度和复合粒子的尺度。相对金纳米粒子膜,制备的复合粒子膜能显著的提高SERS能力,而较大的复合粒子的银壳层和粒子之间的耦合作用对复合粒子膜的SERS活性的显著增强起主要作用。     

Au/Ag核-壳结构纳米粒子的制备及其SERS效应

随着大量有关表面增强拉曼散射 (SERS)的实验和理论研究的开展 ,金属纳米粒子作为一类重要的 SERS增强介质 ,已引起了人们浓厚的研究兴趣 [1] .而 Au和 Ag作为最常用的活性基底物质 ,更是研究的热点 [2 ,3 ] .最近 ,美国印第安那大学的 Nie等 [4 ] 在单个银纳米粒子上 ,观察到高达 1 0 14 ～ 1 0 15的SERS因子 .同时 ,他们的另外一项工作表明银纳米粒子的形状和大小对 SERS活性有很大影响 [5] .但是 ,由于 Ag溶胶制备的重复性较差 ,且粒度分布不均匀 ,通过控制银颗粒大小而调控 SERS活性是相当困难的[6] .与 Ag相比 ,Au在可见光…     

Au/Al2O3催化剂的制备及其在CH4/CO2重整反应中的催化活性

采用浸渍法和沉积－沉淀法制备了四种不同的Au/Al2O3催化剂，测定了它们在氢气还原前后及催化反应后的金含量及比表面积，结果表明，制备方法明显影响催化剂的金含量，应用X－光粉末衍射技术研究了这些催化剂经还原处理及反应后的物相变化，金以Au^0物相存在，没有发现氧化态的金物相，考察了该催化剂在CH4／CO2重整反应中的催化活性，发现金催化剂的活性取决于金粒子的大小，浸渍法制备的金催化剂具有较大的金晶粒尺寸，催化活性低，沉积－沉淀法制备的金催化剂金晶粒尺寸较小，催化活性较高，以尿素为沉淀剂制备的催化剂给出1073K时的CH4和CO2转化率分别为8．1％和17．6％，高温反应不仅导致金晶粒的聚集，而且存在明显的金流失现象。     

Size and shape of Au nanoparticles formed in ionic liquids by electron beam irradiation

Au nano-particles were synthesized via a reductive reaction in ionic liquid solution containing Au(3+) ions using a low-energy electron irradiation technique. In this study, we focused on how the electron beam conditions (acceleration energy, beam current and irradiation time) and the kinds of ionic liquid affected the size and shape of the prepared Au particles. The sizes of the primary particles increased with higher acceleration energy of the electron beam, whereas they did not depend so much on the beam current. Although the amount of secondary particles increased with longer irradiation time, the sizes of the primary particles remained constant. The anion of the ionic liquid strongly affected the size and shape of the primary particles, which was due to the different local structure of the ionic liquid around the Au particles. When the thickness of the ionic liquid layer was smaller than the penetration length of the electron beam, the formation of secondary particles was suppressed. The present results gave an important knowledge for controlling the size and shape of the metal particles, which is important for application of various catalyst or devices.     

Rapid one-step synthesis, characterization and functionalization of silica coated gold nanoparticles

This paper describes a rapid, simple and one-step method for preparing silica coated gold (Au@SiO₂) nanoparticles with fine tunable silica shell thickness and surface functionalization of the prepared particles with different groups. Monodispersed Au nanoparticles with a mean particle size of 16 nm were prepared by citrate reduction method. Silica coating was carried out by mixing the as prepared Au solution, tetraethoxysilane (TEOS) and ammonia followed by microwave (MW) irradiation. Although there are several ways of coating Au nanoparticles with silica in the literature, each of these needs pre-coating step as well as long reaction duration. The present method is especially useful for giving the opportunity to cover the colloidal Au particles with uniform silica shell within very short time and forgoes the use of a silane coupling agent or pre-coating step before silica coating. Au@SiO₂ nanoparticles with wide range of silica shell thickness (5-105 nm) were prepared within 5 min of MW irradiation by changing the concentration of TEOS only. The size uniformity and monodispersity were found to be better compared to the particles prepared by conventional methods, which were confirmed by dynamic light scattering and transmission electron microscopic techniques. The prepared Au@SiO₂ nanoparticles were further functionalized with amino, carboxylate, alkyl groups to facilitate the rapid translation of the nanoparticles to a wide range of end applications. The functional groups were identified by XPS, and zeta potential measurements.     

Preparation of Au Nanoparticles on Surface of Two Supports by Adsorption Phase Synthesis

By utilizing adsorption phase synthesis (APS), Au nanoparticles were prepared on the surface of SiO₂ with or without modification by Ni(OH)₂. TEM, XRD, and UV‐vis were employed to characterize the morphology of Au particles on the surface of two kinds of supports. The results showed that the average size of Au particles on the SiO₂ surface modified by Ni(OH)₂ was less than 5 nm. Due to high surface isoelectric point, Au particles formed in the adsorption layer were prone to distribute on the surface of SiO₂ modified by Ni(OH)₂. With content of Ni(OH)₂ in samples increasing, more Au particles with small size appeared on the support surface.     

Atomic Force Microscopy Study of Ultrafine Particles Prepared in Reverse Micelles

The imaging of ultrafine Au, Pd, CdS, and ZnS particles prepared in reverse micelles has been studied by atomic force microscopy (AFM). Mica substrates, derivatized with a monolayer of amine or thiol-terminated silanes, were used to immobilize the particles. The substrates were exposed to reverse micellar solutions containing the particles and were then immersed in appropriate solvent media to remove surfactants. This resulted in a partial coating of the surfaces by the particles. The particle size was estimated as the height of protrusion, shown on the AFM images. The size values for the Pd and CdS particles, thus obtained, were found to be almost identical to those obtained by transmission electron microscopy (TEM), whereas those for the Au and ZnS particles were larger than those obtained by TEM. Scanning electron microscopy showed that the Au particles tended to aggregate on the surfaces, while Pd particles were isolated from one another. Copyright 2000 Academic Press.     

憎水性三金属纳米粒子的合成、表征及磁性

以磺基琥珀酸二辛酯钠盐(AOT)为表面活性剂,采用反胶束法合成了憎水性CoFe/Au纳米粒子, 利用配体交换、水洗等去除AOT并使纳米粒子分级.采用紫外-可见光谱(UV-Vis)、透射电镜(TEM)、X射线衍射(XRD)、X射线电子能量散射(EDX)及等离子发射光谱 (ICP)等对产物进行了表征,通过超导量子干涉仪(SQIUD)研究了纳米粒子的磁性质.结果表明,反胶束法合成的CoFe/Au三金属纳米粒子具有较好的单分散性和稳定性,平均粒径约为4 nm.当外磁场强度为1.5×10⁴ A/m时,阻塞温度T_b为65 K,温度高于T_b时纳米粒子显示出超顺磁性,低于T_b时呈铁磁性,在5 K时其矫顽力(Hc)达4.67×10⁴ A/m.     

金核银壳纳米粒子薄膜的制备及SERS活性研究

采用柠檬酸化学还原法制备金溶胶, 通过自组装技术在石英片表面制备金纳米粒子薄膜, 在银增强剂混合溶液中反应获得金核银壳纳米粒子薄膜. 用紫外-可见吸收光谱仪和原子力显微镜(AFM)研究了不同条件下制备的金核银壳纳米粒子薄膜的光谱特性和表面形貌, 并以结晶紫为探针分子测量了金核银壳纳米粒子薄膜的表面增强拉曼光谱(SERS). 结果表明, 金纳米粒子薄膜的分布、银增强剂反应时间的长短对金核银壳纳米粒子薄膜的形成均有重要影响. 制备过程中, 可以通过控制反应条件获得一定粒径的、具有良好表面增强拉曼散射活性的金核银壳纳米粒子薄膜.     

New preparation method of gold nanoparticles on SiO2

It is shown that adsorption of the [Au(en)(2)](3+) cationic complex can be successfully employed for the deposition of gold nanoparticles (1.5 to 3 nm) onto SiO(2) with high metal loading, good dispersion, and small Au particle size. When the solution pH increases (from 3.8 to 10.5), the Au loading in the Au/SiO(2) samples increases proportionally (from 0.2 to 5.5 wt %), and the average gold particle size also increases (from 1.5 to 2.4 nm). These effects are explained by the increase in the amount of negatively charged sites present on the SiO(2) surface, namely, when the solution pH increases, a higher number of [Au(en)(2)](3+) species can be adsorbed. Extending the adsorption time from 2 to 16 h gives rise to an increase in the gold loading from 3.3 to 4.0 wt % and in the average particle size from 1.8 to 2.9 nm. Different morphologies of gold nanoparticles are present as a function of the particle size. Particles with a size of 3-5 nm show defective structure, some of them having a multiple twinning particle (MTP) structure. At the same time, nanoparticles with an average size of ca. 2 nm exhibit defect-free structure with well-distinguishable {111} family planes. TEM and HAADF observations revealed that Au particles do not agglomerate on the SiO(2) support: gold is present on the surface of SiO(2) only as small particles. Density functional theory calculations were employed to study the mechanisms of [Au(en)(2)](3+) adsorption, where neutral and negatively charged silica surfaces were simulated by neutral cluster Si(4)O(10)H(4) and negatively charged cluster Si(4)O(10)H(3), respectively. The calculation results are totally consistent with the suggestion that the deposition of gold takes place according to a cationic adsorption mechanism.     

微波法合成纳米金胶体颗粒的调控研究

用微波法制备高分子聚合物稳定的纳米金胶体颗粒, 制得的金纳米颗粒的平均粒径在5～120 nm之间. 考察了醇还原剂以及碱对金颗粒形成的影响, 使用透射电子显微镜、紫外可见分光光度计进行表征. 结果表明, 微波法制备的金胶体颗粒具有粒径小、分散性好的特点. 金颗粒的尺寸和形状随醇还原剂的种类及碱(NaOH)用量的不同而有明显的变化. 紫外可见吸收光谱表明, 在反应物中加入碱的体系, 金颗粒的形成速度明显加快, 且利于圆球形金颗粒的形成.