Conductivity and sintering property of LaNi1 − xFexO3 ceramics prepared by Pechini method

Preparation of LaNi_1 − xFe_xO₃, which is one of the candidate materials of solid oxide fuel cell cathode, current collecting layer and interconnect coating was examined with Pechini method and solid state reaction method. Single phase LaNi_1 − xFe_xO₃ with large Ni content has successfully been prepared by low temperature sintering as 750 °C with Pechini method, whereas large amount of raw materials has remained with solid state reaction method by sintering at the same temperature. It can be ascribed to more homogenous cation distribution in raw powder material prior to sintering with Pechini method. It has also been revealed that LaNi_1 − xFe_xO₃ with x lower than 0.3 is thermodynamically unstable in air above 1000 °C. LaNi_0.6Fe_0.4O₃ showed superior property as cathode material with high electrical conductivity, thermodynamic stability and appropriate sintering property.     

Synthesis and magnetic properties of La-substituted M-type Sr hexaferrites

Single-phase M-type hexagonal ferrites Sr_1−xLa_xFe₁₂O₁₉ (0≤x≤1) were prepared by a ceramic route. The stability limits of the ferrite phases were determined with a combination of various microscopy techniques, electron-probe micro-analysis, powder X-ray diffraction and thermal analysis. SrFe₁₂O₁₉ (x=0) is stable up to 1420 °C, whereas LaFe₁₂O₁₉ (x=1) exists between 1360 and 1400 °C only. The lattice parameters of Sr_1−xLa_xFe₁₂O₁₉ exhibit a linear variation with x, i.e. a₀ slightly increases and c₀ decreases with x, leading to a decrease of the unit cell volume with x. The saturation magnetization at T=5 K decreases with increasing La concentration. Room temperature Mössbauer analysis shows that the Fe³⁺/Fe²⁺ valence change occurs in the 2a sites for the whole composition range.     

Preparation and magnetic properties of the conductive Co(1−x)NixFe2O4/polyaniline microsphere composites

Core-shell Co_(1−x)Ni_xFe₂O₄/polyaniline nanoparticles, where the core was Co_(1−x)Ni_xFe₂O₄ and the shell was polyaniline, were prepared by the combination of sol-gel process and in-situ polymerization methods. Nanoparticles were investigated by Fourier transform spectrometer, X-ray diffraction diffractometer, Scanning electron microscope, Differential thermal analysis and Superconductor quantum interference device. The results showed that the saturation magnetization of pure Co_(1−x)Ni_xFe₂O₄ nanoparticles were 57.57 emu/g, but Co_(1−x)Ni_xFe₂O₄/polyaniline composites were 37.36 emu/g. It was attributed to the lower content (15 wt%), smaller size and their uneven distribution of Co_(1−x)Ni_xFe₂O₄ nanoparticles in the final microsphere composites. Both Co_(1−x)Ni_xFe₂O₄ and PANI/Co_(1−x)Ni_xFe₂O₄ showed superparamagnetism.     

Investigations on the spin Hamiltonian parameters and defect structure for the interstitial Mo centre in TiO2

The spin Hamiltonian parameters, g factors g_i (i = x, y, z) and the hyperfine structure constants A_i for the interstitial Mo⁵⁺ centre in rutile TiO₂ are quantitatively investigated from the perturbation formulas of these parameters for a 4d¹ ion in rhombically compressed octahedra. From the studies, the local compression parameter τ′ (≈0.024) and the rhombic distortion angle δ?′ (≈1.74°) around the impurity Mo⁵⁺ are smaller than the host values (≈0.091 and 3.5°). This means that the oxygen octahedron in the impurity centre has less rhombic distortion than that on the host interstitial site due to the Jahn–Teller effect and occupation of the impurity. The above local lattice distortion of the studied impurity centre is also discussed.     

Bulk and surface properties of spinel Co3O4 by density functional calculations

DFT calculations are employed to bulk and surface properties of spinel oxide Co₃O₄. The bulk magnetic structure is calculated to be antiferromagnetic, with a Co²⁺ moment of 2.631 μ_B in the antiferromagnetic state. There are three predicted electron transitions O(2p) → Co²⁺(t_2g) of 2.2 eV, O(2p) → Co³⁺(e_g) of 2.9 eV and Co³⁺(t_2g) → Co²⁺(t_2g) of 3.3 eV, and the former two transitions are close to the corresponding experimental values 2.8 and 2.4 eV. The naturally occurring Co₃O₄ (1 1 0) and (1 1 1) surfaces were considered for surface calculations. For ideal Co₃O₄ (1 1 0) surfaces, the surface relaxations are not significant, while for ideal Co₃O₄ (1 1 1) surfaces the relaxation of Co²⁺ cations in the tetrahedral sites is drastic, which agrees with the experiment observation. The stability over different oxygen environments for possible ideal and defect surface terminations were explored.     

High temperature ferromagnetism of the vacuum-annealed (In1−xFex)2O3 powders

(In_1−xFe_x)₂O₃ (x = 0.02, 0.05, 0.2) powders were prepared by a solid state reaction method and a vacuum annealing process. A systematic study was done on the structural and magnetic properties of (In_1−xFe_x)₂O₃ powders as a function of Fe concentration and annealing temperature. The X-ray diffraction and high-resolution transmission electron microscopy results confirmed that there were not any Fe or Fe oxide secondary phases in vacuum-annealed (In_1−xFe_x)₂O₃ samples and the Fe element was incorporated into the indium oxide lattice by substituting the position of indium atoms. The X-ray photoelectron spectroscopy revealed that both Fe²⁺ and Fe³⁺ ions existed in the samples. Magnetic measurements indicated that all samples were ferromagnetic with the magnetic moment of 0.49-1.73 μ_B/Fe and the Curie temperature around 783 K. The appearance of ferromagnetism was attributed to the ferromagnetic coupling of Fe²⁺ and Fe³⁺ ions via an electron trapped in a bridging oxygen vacancy.     

High-throughput characterization of BixY3−xFe5O12 combinatorial thin films by magneto-optical imaging technique

Bi_xY_3−xFe₅O₁₂ thin films have been grown on GGG (Gd₃Ga₅O₁₂) (1 1 1) substrates by the combinatorial composition-spread techniques under substrate temperature (T_sub) ranging from 410 to 700 °C and O₂ pressure of 200 mTorr. In order to study the effect of substrates on the deposition of Bi_xY_3−xFe₅O₁₂ thin films, garnet substrates annealed at 1300 °C for 3 h were also used. Magneto-optical properties were characterized by our home-designed magneto-optical imaging system. From the maps of Faraday rotation angle θ_F, it was evident that the Faraday effect appears only when T_sub = 430-630 °C. θ_F reaches to the maximum value (∼6°/μm, λ = 632 nm) at 500 °C, and is proportional to the Bi contents. XRD and EPMA analyses showed that Bi ions are easier to substitute for Y sites and better crystallinity is obtained for annealed substrates than for commercial ones.     

Epitaxial MoOx nanostructures on TiO2(1 1 0) obtained using thermal decomposition of Mo(CO)6

Stoichiometric and highly-defective TiO₂(1 1 0) surfaces (called as yellow and blue, respectively) were exposed to Mo(CO)₆ vapours in UHV and in a reactive O₂ atmosphere. In the case of yellow-TiO₂, an O₂ reactive atmosphere was necessary to obtain the Mo(CO)₆ decomposition at 450 °C with deposition of MoO_x nanostructures where, according to core level photoemission data, the Mo⁺⁴ state is predominant. In the case of blue-TiO₂ it was possible to obtain Mo deposition both in UHV and in an O₂ atmosphere. A high dose of Mo(CO)₆ in UHV on blue-TiO₂ allowed the deposition of a thick metallic Mo layer. An air treatment of this sample at 580 °C led to the elimination of Mo as MoO₃ and to the formation of a transformed layer of stoichiometry of Ti_(1−x)Mo_xO₂ (where x is close to 0.1) which, according to photoelectron diffraction data, can be described as a substitutional near-surface alloy, where Mo⁺⁴ ions are embedded into the titania lattice. This embedding procedure results in a stabilization of the Mo⁺⁴ ions, which are capable to survive to air exposure for a rather long period of time. After exposure of the blue-TiO₂(1 1 0) substrate to Mo(CO)₆ vapours at 450 °C in an O₂ atmosphere it was possible to obtain a MoO₂ epitaxial ultrathin layer, whose photoelectron diffraction data demonstrate that is pseudomorphic to the substrate.     

Low temperature adsorption of oxygen on reduced V2O3(0 0 0 1) surfaces

Well ordered V₂O₃(0 0 0 1) films were prepared on Au(1 1 1) and W(1 1 0) substrates. These films are terminated by a layer of vanadyl groups under typical UHV conditions. Reduction by electron bombardment may remove the oxygen atoms of the vanadyl layer, leading to a surface terminated by vanadium atoms. The interaction of oxygen with the reduced V₂O₃(0 0 0 1) surface has been studied in the temperature range from 80 to 610 K. Thermal desorption spectroscopy (TDS), infrared reflection absorption spectroscopy (IRAS), high resolution electron energy loss spectroscopy (HREELS), X-ray photoelectron spectroscopy (XPS), and density functional theory (DFT) were used to study the adsorbed oxygen species. Low temperature adsorption of oxygen on reduced V₂O₃(0 0 0 1) occurs both dissociatively and molecularly. At 90 K a negatively charged molecular oxygen species is observed. Upon annealing the adsorbed oxygen species dissociates, re-oxidizing the reduced surface by the formation of vanadyl species. Density functional theory was employed to calculate the structure and the vibrational frequencies of the O₂ species on the surface. Using both cluster and periodic models, the surface species could be identified as η²-peroxo () lying flat on surface, bonded to the surface vanadium atoms. Although the O-O vibrational normal mode involves motions almost parallel to the surface, it can be detected by infrared spectroscopy because it is connected with a change of the dipole moment perpendicular to the surface.     

Complex permittivity, complex permeability and microwave absorption properties of ferrite-paraffin polymer composites

We have investigated the electromagnetic (EM) characteristics of Co_xMn_1−xFe₂O₄ spinel ferrite (where x=0.0, 0.5 and 1.0) nanoparticles (NPs)/paraffin nanocomposite material at 8-20 GHz. Co_xMn_1−xFe₂O₄ NPs have been synthesized by cetyltrimethylammonium assisted hydrothermal route using NaOH. A variation in complex dielectric permittivity and magnetic permeability at room temperature with frequency in the range 8-20 GHz has been studied. Particles showed phase purity and crystallinity in powder X-ray diffraction (XRD) analysis. At the same time, Co_xMn_1−xFe₂O₄ NPs demonstrated a spinel cubic structure from XRD results. A reflection loss of −46.60 dB was found at 10.5 GHz for an absorber thickness of 2 mm. Co_xMn_1−xFe₂O₄ may be attractive candidates for EM wave absorption materials.     

The nature of antimony-enriched surface layer of Fe-Sb mixed oxides

Antimony segregation is a common feature in Fe-Sb mixed oxides, which have been widely applied as catalysts in selective oxidation and ammoxidation reactions. This paper attempts to shed a light on the cause of such a common feature and on the nature of the antimony-enriched surface layer over FeSbO₄ by means of XPS surface analysis. Single-phase FeSbO₄ samples prepared by different methods were studied, and the antimony in their surface layer is a mixture of both Sb⁵⁺ and Sb³⁺ rather than single Sb⁵⁺. Their surface composition is close to FeSb₂O₆, which could be described as (FeSbO₄)(Sb₂O₄)_δ, δ = 0.5, and it is not “Fe(II)Sb(V)₂O₆” as suggested in literature. Fe-Sb mixed oxides with Sb/Fe > 1 (mol/mol) are mixtures of FeSbO₄ and Sb₂O₄, and the surface of FeSbO₄ grains would be a layer of (FeSbO₄)(Sb₂O₄)_δ, δ ≥ 0.5. Fe-Sb mixed oxides with Sb/Fe < 1 are mixtures of FeSbO₄ and Fe₂O₃, and the surface of FeSbO₄ grains would be a layer of (FeSbO₄)(Sb₂O₄)_δ, δ ≤ 0.5, but the remaining Fe₂O₃ would be encapsulated by a layer of FeSbO₄.     

Site-blocking effects of preadsorbed H on Pt(1 1 1) probed by 1,3-butadiene adsorption and reaction

The influence of hydrogen coadsorption on hydrocarbon chemistry on transition metal surfaces is a key aspect to an improved understanding of catalytic selective hydrogenation. We have investigated the effects of H preadsorption on adsorption and reaction of 1,3-butadiene (H₂CCHCHCH₂, C₄H₆) on Pt(1 1 1) surfaces by using temperature-programmed desorption (TPD) and Auger electron spectroscopy (AES). Preadsorbed hydrogen adatoms decrease the amount of 1,3-butadiene chemisorbed on the surface and chemisorption is completely blocked by the hydrogen monolayer (saturation) coverage (θ_H = 0.92 ML). No hydrogenation products of reactions between coadsorbed H adatoms and 1,3-butadiene were observed to desorb in TPD experiments over the range of θ_H investigated (θ_H = 0.6-0.9 ML). This is in strong contrast to the copious evolution of ethane (CH₃CH₃, C₂H₆) from coadsorbed hydrogen and ethylene (CH₂CH₂, C₂H₄) on Pt(1 1 1). Hydrogen adatoms effectively (in a 1:1 stoichiometry) remove sites from interaction with chemisorbed 1,3-butadiene, but do not affect adjacent sites. The adsorption energy of coadsorbed 1,3-butadiene is not affected by the presence of hydrogen on Pt(1 1 1). The chemisorbed 1,3-butadiene on hydrogen preadsorbed Pt(1 1 1) completely dehydrogenates to H₂ and surface carbon upon heating without any molecular desorption detected, which is identical to that observed on clean Pt(1 1 1). In addition to revealing aspects of site blocking that should have broad implications for hydrogen coadsorption with hydrocarbon molecules on transition metal surfaces in general, these results also provide additional basic information on the surface science of selective catalytic hydrogenation of butadiene in butadiene-butene mixtures.     

Effect of Li2O and CoO-doping of CuO/Fe2O3 system on its surface and catalytic properties

Physicochemical, surface and catalytic properties of pure and doped CuO/Fe₂O₃ system were investigated using X-ray diffraction (XRD), energy dispersive X-ray analysis (EDX), nitrogen adsorption at −196 °C and CO-oxidation by O₂ at 80-220 °C using a static method. The dopants were Li₂O (2.5 mol%) and CoO (2.5 and 5 mol%). The results revealed that the increase in precalcination temperature from 400 to 600 °C and Li₂O-doping of CuO/Fe₂O₃ system enhanced CuFe₂O₄ formation. However, heating both pure and doped solids at 600 °C did not lead to complete conversion of reacting oxides into CuFe₂O₄. The promotion effect of Li₂O dopant was attributed to dissolution of some of dopant ions in the lattices of CuO and Fe₂O₃ with subsequent increase in the mobility of reacting cations. CoO-doping led also to the formation of mixed ferrite Co_xCu_1−xFe₂O₄. The doping process of the system investigated decreased to a large extent the crystallite size of unreacted portion of Fe₂O₃ in mixed solids calcined at 600 °C. This process led to a significant increase in the S_BET of the treated solids. Doping CuO/Fe₂O₃ system with either Li₂O or CoO, followed by calcination at 400 and 600 °C decreased its catalytic activity in CO-oxidation by O₂. However, the activation energy of the catalyzed reaction was not much affected by doping.     

Low-voltage cathodoluminescence property of Li-doped Gd2−xYxO3:Eu

Cathodoluminescent (CL) spectra of Li-doped Gd_2−xY_xO₃:Eu³⁺ solid-solution (0.0?x?0.8) were investigated at low voltages (300 V-1 kV). The CL intensity is maximum for the composition of x=0.2 and gradually reduces with increasing the amount of substituted Y content. In particular, small (∼100 nm) particles of Li-doped Gd_1.8Y_0.2O₃:Eu³⁺ are obtained by firing the citrate precursors at only 650°C for 18 h. Relative red-emission intensity at 300 V of this phosphor is close to 180% in comparison with that of commercial red phosphor Y₂O₃:Eu³⁺. An increase of firing temperature to 900°C results in 400-600 nm sized spherical particles. At low voltages (300-800 V), the CL emission of 100 nm sized particles is much stronger than that of 400-600 nm sized ones. In contrast, the larger particles exhibit the higher CL emission intensity at high voltages (1-10 kV). Taking into consideration small spherical morphology and effective CL emission, Li-doped Gd_1.8Y_0.2O₃:Eu³⁺ appears to be an efficient phosphor material for low voltage field emission display.     

Thermal stability, oxygen non-stoichiometry and transport properties of LaNi0.6Fe0.4O3

Thermal stability, oxygen non-stoichiometry and electrical conductivity of LaNi_0.6Fe_0.4O_3−δ were investigated in the temperature region of 20-1000 °C in Ar/O₂ gas flows at oxygen partial pressures between 0.5 and 21,000 Pa. Diffusion mobility was measured in Ar/O₂ gas flow at pO₂ = 18 Pa. Crystal structure of this compound was found to be stable at the mentioned experimental conditions. LaNi_0.6Fe_0.4O_3−δ is a p-type semiconductor with metallic type conductivity above 150 °C at the investigated pO₂ range. Two different (fast and slow) oxygen exchange areas on the temperature-pO₂ diagram were established, which are due to two different oxygen anion positions in the double B-site mixed perovskite structure. Oxygen non-stoichiometry in the fast oxygen exchange region reaches about 0.005 of oxygen atomic index. Chemical diffusion and oxygen surface exchange coefficients do not vary at 600-800 °C, but show visible increase above 800-850 °C.     

Ab initio studies of electronic spectra of the linear aluminum-bearing carbon chains AlC2nH (n = 1-5)

Geometries and stabilities of the linear aluminum-bearing carbon chains AlC_2nH (n = 1-5) in their ground states have been explored by the DFT-B3LYP and RCCSD(T) methods. Structures of the X¹Σ⁺ and 1¹Π electronic states have also been optimized by the CASSCF approach. The studies indicate that these species have single-triple bond alternate pattern, AlCCCC?CCH, and the electronic excitation from X¹Σ⁺ to 1¹Π leads to the shortening of the AlC bonds. The vertical excitation energies of the 1¹Π ← X¹Σ⁺ and 2¹Π ← X¹Σ⁺ transitions for AlC_2nH (n = 1-5) have been investigated by the CASPT2, EOM-CCSD, and TD-B3LYP levels of theory with the cc-pVTZ basis set, respectively. CASPT2-predicted 1¹Π ← X¹Σ⁺ transition energies are 3.57, 3.44, 3.33, 3.26, and 3.21 eV, respectively. For AlC₂H, our estimate agrees very well with the experimental value of 3.57 eV. In addition, the AlC bond dissociation energies and the exponential-decay curves for these vertical excitation energies are also discussed.     

Preparation and magnetic properties of BaFe12O19/Ni0.8Zn0.2Fe2O4 nanocomposite ferrite

Nanocomposite of hard (BaFe₁₂O₁₉)/soft ferrite (Ni_0.8Zn_0.2Fe₂O₄) have been prepared by the sol–gel process. The nanocomposite ferrite are formed when the calcining temperature is above 800 °C. It is found that the magnetic properties strongly depend on the presintering treatment and calcining temperature. The “bee waist” type hysteresis loops for samples disappear when the presintering temperature is 400 °C and the calcination temperature reaches 1100 °C owing to the exchange-coupling interaction. The remanence of BaFe₁₂O₁₉/Ni_0.8Zn_0.2Fe₂O₄ nanocomposite ferrite with the mass ratio of 5:1 is higher than a single phase ferrite. The specific saturation magnetization, remanence magnetization and coercivity are 63 emu/g, 36 emu/g and 2750 G, respectively. The exchange-coupling interaction in the BaFe₁₂O₁₉/Ni_0.8Zn_0.2Fe₂O₄ nanocomposite ferrite is discussed.     

Magnesia formed on calcination of Mg(OH)2 prepared from natural bischofite

Calcination of magnesium hydroxide, which was prepared from natural bischofite MgCl₂·6H₂O, leading to dehydration 2(MgOH) → MgOMg + H₂O, is accompanied by transition of phase not only to MgO but also to MgO_x at x < 1 (assigned to Mg₄O₃) at moderate temperatures. At higher temperatures, MgO_x is completely transformed into MgO. Magnesium hydroxide and oxide heated at different temperatures were studied using the TEM, XRD, IR, PCS, TG-DTA, nitrogen and argon adsorption methods. The electronic structure of MgO and Mg₄O₃ was studied using the ab initio quantum chemical method with periodic conditions. According to TEM images, the morphology of particles changing from Mg(OH)₂ laminae to aggregates of interpenetrated MgO cubelets and foils depend strongly on the calcination temperature. Significant changes in surface area are observed mainly at 325-470 °C on desorption of a major portion of eliminated water corresponding to 28.4 wt.% at its total amount of 30.9 wt.%. Pore size distribution (PSD) is sensitive to treatment conditions and the main PSD peaks shift towards larger pore size with elevating temperature. The characteristics of the surface hydroxyls as well as of the bulk MgO bonds depend on heating conditions, as noticeable changes are observed in the XRD patterns and the IR spectra of the samples undergoing the mentioned transformation of phase Mg(OH)₂ → MgO_x → MgO.     

Formamide reactions on rutile TiO2(0 1 1) surface

The reaction of formamide over the (0 1 1) faceted TiO₂(0 0 1) surface has been studied by Temperature Programmed Desorption (TPD) and X-ray Photoelectron Spectroscopy (XPS). Two main reactions were observed: dehydration to HCN and H₂O and decomposition to NH₃ and CO. The dehydration reaction was found to be three to four times larger than the decomposition at all coverages. Each of these reactions is found to occur in two temperature domains which are dependent upon surface coverage. The low temperature pathway (at about 400 K) is largely insensitive to surface coverage while the high temperature pathway (at about 500 K) shifts to lower temperatures with increasing surface coverage. These two temperature pathways may indicate two adsorption modes of formamide: molecular (via an η¹(O) mode of adsorption) and dissociative (via an η²(O,N) mode of adsorption). C1s and N1s XPS scans indicated the presence of multiple species after formamide absorption at 300 K. These occurred at ca. 288.5 eV (-CONH-) and 285 eV (sp³/sp² C) for the C1s and 400 eV-(NH₂), 398 eV (-NH) and 396 eV (N) for the N1s and result from further reaction of formamide with the surface.     

Effects of different sintering temperature and Nb2O5 content on structural and magnetic properties of Z-type hexaferrites

Nb-doped Z-type hexaferrites (Ba₃(Co_0.4Zn_0.6)₂Fe₂₄O₄₁) with composition of Ba₃(Co_0.4Zn_0.6)₂Fe₂₄O₄₁+x Nb₂O₅ (where x=0.0, 0.1, 0.2, 0.4, 0.6, 0.8, 1.2, 1.6 and 2.0 wt%) were prepared by a solid-state reaction method. The effects of different sintering temperature (T_s) and Nb₂O₅ content on the sintering behaviors, phase composing, microstructure, and magnetic properties of the samples were investigated. The results from X-ray diffraction and scanning electron microscopy show that as the amount of Nb₂O₅ additive increases, the major phase changes to Z-phase, Simultaneously, M-phase and a small amount of niobate phase appear. The Nb₂O₅ additive promotes the grain growth as reaction center at lower sintering temperature (1220 °C), but at higher temperature (1260 °C), niobate phase separated out in grain boundaries as secondary phase will restrain abnormal grain growth, so closed pores in grains are not formed. The Nb₂O₅ additive can enhance densification, improve initial permeability of hexaferrites by increasing the grain growth of hexaferrite and the displacement of ions in the sintering process due to the aberration and activation of crystal lattice, which is accompanied by the solubility of Nb⁵⁺ in the hexaferrites. A relative density of 96%, maximum initial permeability (32–33), minimum coercivity (454–455 A/m) and resonance frequency above 400 MHz were obtained for the sample with 0.8 wt% Nb₂O₅ sintered at 1260 °C for 6 h.