Sr-doped LaInO3 and its possible application in a single layer SOFC

The effects of dopants on the electrical conductivity of the perovskite-type oxide LaInO₃ have been investigated. Replacement of La by Sr is the most effective way to enhance the conductivity of LaInO₃, whereas Ca substitution for In is rather difficult due to the large difference in the ion radii. The optimum composition is La_0.9Sr_0.1InO_3−δ whose maximum conductivity is 7.6×10⁻³ S cm⁻¹ at 900°C. The electrical conductivity of La_0.9Sr_0.1InO_3−δ has been measured over a wide range of oxygen partial pressure from pO₂=1 to 10⁻²⁵ atm. P-type and n-type behavior at high and low oxygen partial pressure have been observed, respectively, while at intermediate oxygen partial pressures, the electrical conductivity changes only slightly with the oxygen partial pressure. The concept of a single layer solid oxide fuel cell based on a La_0.9Sr_0.1InO_3−δ ceramic pellet has been tested. A maximum power density of 3 mW cm⁻² at 800°C was achieved when dilute H₂ and air were used as fuel and oxidizing agent, respectively.     

Tuning the magnetic and electronic properties of strontium titanate by carbon doping

The magnetic and electronic properties of strontium titanate with different carbon dopant configurations are explored using first-principles calculations with a generalized gradient approximation (GGA) and the GGA+U approach. Our results show that the structural stability, electronic properties and magnetic properties of C-doped SrTiO₃ strongly depend on the distance between carbon dopants. In both GGA and GGA+U calculations, the doping structure is mostly stable with a nonmagnetic feature when the carbon dopants are nearest neighbors, which can be ascribed to the formation of a C–C dimer pair accompanied by stronger C–C and weaker C–Ti hybridizations as the C–C distance becomes smaller. As the C–C distance increases, C-doped SrTiO₃ changes from an n-type nonmagnetic metal to ferromagnetic/antiferromagnetic half-metal and to an antiferromagnetic/ferromagnetic semiconductor in GGA calculations, while it changes from a nonmagnetic semiconductor to ferromagnetic half-metal and to an antiferromagnetic semiconductor using the GGA+U method. Our work demonstrates the possibility of tailoring the magnetic and electronic properties of C-doped SrTiO₃, which might provide some guidance to extend the applications of strontium titanate as a magnetic or optoelectronic material.     

Electrical conductivity improvement of strontium titanate doped lead vanadate glasses by nanocrystallization

The structural and electrical conductivity (σ) of annealed SrTiO₃–PbO₂–V₂O₅ glasses were studied. The annealing of initially glass samples leads to formation of nanocrystalline grains embedded in the glassy matrix. XRD patterns of the glass–ceramic samples show that nanocrystals were embedded in the glassy matrix with an average grain size of 32 nm. The glass–ceramic nanocrystals obtained by annealing at temperatures close to the crystallization temperature T_c exhibit enhancement of electrical conductivity up to four orders of magnitude than initially glasses. The enhancement of the electrical conductivity due to annealing was attributed to two interdependent factors: (i) an increase of concentration of V⁴⁺–V⁵⁺ pairs; and (ii) formation of defective, well-conducting regions along the glass–crystallites interfaces. From the conductivity temperature relation, it was found that small polaron hopping model was applicable at temperature above θ_D/2 (θ_D, the Debye temperature). The electrical conduction at T >θ_D/2 was due to non-adiabatic small polaron hopping (SPH) of electrons between vanadium ions. The parameters obtained from the fits of the experimental data to this model appear reasonable and are consistent with glass composition.     

Niobium based tetragonal tungsten bronzes as potential anodes for solid oxide fuel cells: synthesis and electrical characterisation

In this paper we report studies on a range of niobate based tungsten bronzes, with a view to analysing their potential as anode materials in SOFCs. Six systems were studied, (Sr_1−xBa_x)_0.6Ti_0.2Nb_0.8O₃, Sr_0.6−xLa_xTi_0.2+xNb_0.8−xO₃, (Sr_0.4−xBa_x)Na_0.2NbO₃, (Ba_1−xCa_x)_0.6Ti_0.2Nb_0.8O₃, Ba_0.5−xA_xNbO₃ (A=Ca, Sr), and Ba_0.3NbO_2.8, and the electrical conductivities were examined over a range of oxygen partial pressures (10⁻²⁰–1 bar). All the systems showed good conductivity in low oxygen partial pressures, with values as high as 8 S cm⁻¹ at 930°C (P(O₂)=10⁻²⁰ bar). As the oxygen partial pressure was raised the conductivity dropped showing in most cases an approximate [P(O₂)]^−1/4 dependence and good re-oxidation kinetics. Of all the samples studied the (Sr_1−xBa_x)_0.6Ti_0.2Nb_0.8O₃ and (Ba_1−xCa_x)_0.6Ti_0.2Nb_0.8O₃ systems appear most promising for potential use as anode materials in SOFCs.     

Electrochemical properties of nanostructured lanthanum strontium manganite cathode fabricated by electrostatic spray deposition

Electrostatic spray deposition was applied to prepare nanoporous lanthanum strontium manganite (LSM) films with high specific surface area (37.34 m²/g) for the cathode application in solid oxide fuel cell (SOFC). The electrochemical characteristics were investigated at a temperature range from 546 to 777 °C and oxygen partial pressure from 0.01 to 1.0 atm. The diffusion of atomic oxygen and oxygen ion transfer from three-phase boundary to the YSZ electrolyte were found to be the rate-determining steps for oxygen reduction reaction on LSM cathode. The polarization resistance of the LSM prepared using electrostatic spray deposition decreased from 15 to 1.2 Ωcm² with increasing temperature from 546 to 777 °C and the activation energy was 0.81 eV. It was demonstrated that the ESD method offers a promising approach for the preparation of electrochemically active nanoporous layers, particularly applicable for solid oxide fuel cells.     

Electrical and thermal properties of lead titanate glass ceramics

Glass samples with composition of (50−X)PbO-(25+X)TiO₂-25B₂O₃ (where X=0, 5, 10 and 12.5 mol%) were prepared using conventional quenching technique. The glass transition temperature, T_g and crystallization temperature T_c were determined from the DTA. These glass samples were converted to glass ceramics by following two stage heat treatment schedule. The glass ceramic samples were characterized by XRD, SEM and dielectric constant measurements. The XRD results revealed the formation of ferroelectric lead titanate (PT) as a major crystalline phase in the glass ceramics. The density increases and the CTE decreases for all glass ceramics with increase in X (mol%). This may be attributed to increase in PT phase. The SEM results which show rounded crystallites of lead titanate, also supports other results. Hysteresis loops observed at room temperature confirms the ferroelectric nature of glass ceramics. The optimized glass ceramic sample exhibits high dielectric constant which is of technical importance.     

Effect of cation doping on ionic and electronic properties for lanthanum silicate-based solid electrolytes

Electronic as well as ionic conducting properties for oxyapatite-type solid electrolytes based on lanthanum silicate, La_9.333 + xSi₆O_26 + 1.5x (LSO) were investigated in the oxygen-excess region (x > ca. 0.3). We have found that the oxygen excess-type LSO (OE-LSO), namely La₁₀Si₆O₂₇ on weighted basis, exhibited high conductivity, and substitution of the Si-site of LSO with some dopants (Mⁿ⁺) had a positive effect toward the conducting property. Furthermore, it was also found that addition of a very small amount of iron ions into the M-doped OE-LSO, La₁₀(Si_6-yMⁿ⁺_y)O_27-(2-0.5n)y, improved its conductivity. On the other hand, replacement of the La-site with various ions for La₁₀(Si_6-yMⁿ⁺_y)O_27-(2-0.5n)y did little to improve conductivity. The electronic transport numbers for Al-doped OE-LSO with Fe-addition, (1-α){La₁₀(Si_5.8Al_0.2)O_26.9}-α(FeO_γ), evaluated with the Hebb-Wagner polarization method were very low: i.e., 1.1 × 10^− 3 and 2.9 × 10^− 3 under P(O₂) = 1.1 × 10⁴ Pa at 1073 K for α = 0.00 and 0.005, respectively. Conductivity for each sample was unchanged under humidified atmosphere at 1073 K sustained for over 50 h, revealing that both compositions were chemically stable. It was concluded that 0.995{La₁₀(Si_5.8Al_0.2)O_26.9}-0.005(FeO_γ) is suitable for the fuel cell electrolytes because of its high and almost pure ionic conductivity, and its good chemical stability under humidified as well as reducing conditions.     

Effect of substrate temperature on the structural, optical and electrical properties of dc magnetron sputtered tantalum oxide films

dc reactive magnetron sputtering technique was employed for deposition of tantalum oxide films on quartz and silicon substrates by sputtering of pure tantalum target in the presence of oxygen and argon gases under various substrate temperatures in the range 303-973 K. The variation of cathode potential with the oxygen partial pressure was systematically studied. The influence of substrate temperature on the chemical binding configuration, crystal structure and optical properties was investigated. X-ray photoelectron spectroscopic studies indicated that the films formed at oxygen partial pressures ≥1 × 10⁻⁴ mbar were stoichiometric. The Fourier transform infrared spectroscopic studies revealed that the films formed up to substrate temperatures <673 K showed a broad absorption band at 750-1000 cm⁻¹ and a sharp band at 630 cm⁻¹ indicated the presence of amorphous phase while at higher substrate temperatures the appearance of bands at about 810 and 510 cm⁻¹ revealed the polycrystalline nature. The effect of substrate temperature on the electrical characteristics of Al/Ta₂O₅/Si structure was investigated. The dielectric constant values were in the range 17-29 in the substrate temperature range of 303-973 K. The current-voltage characteristics showed modified Poole-Frenkel conduction mechanism with a tendency for reduction of the compensation level. The optical band gap of the films decreased from 4.44 to 4.25 eV and the refractive index increased from 1.89 to 2.25 with the increase of substrate temperature from 303 to 973 K.     

Synthesis and characterization of doped apatite-type lanthanum silicates for SOFC applications

A series of iron- and/or aluminium-doped apatite-type lanthanum silicates (ATLS) La_9.83Si_{6 ‐ x ‐ y}Al_xFe_yO_26 ± δ (x = 0, 0.25, 0.75, and 1.5, y = 0, 0.25, 0.75, and 1.5) were synthesized using the mechanochemical activation (MA), solid state reaction (SSR), Pechini (Pe) and sol-gel (SG) methods. The total conductivity of the prepared materials was measured under air in the temperature range 600-850 °C using 4-probe AC impedance spectroscopy. Its dependence on composition, synthesis method, sintering conditions and powder particle size was investigated. It was found that for electrolytes of the same composition, those prepared via mechanochemical activation exhibited the highest total specific conductivity, which was improved with increasing Al- and decreasing Fe-content. The highest conductivity value at 700 °C, equal to 2.04 × 10^− 2 S cm^− 1, was observed for the La_9.83Si₅Al_0.75Fe_0.25O_26 ± δ electrolyte. La_9.83Si_4.5Fe_1.5O_26 ± δ electrolyte samples synthesized using the Pechini method exhibited higher conductivity when sintered conventionally than when spark-plasma sintering (SPS) was used.     

Electrical conductivity and dielectric constant of A-type Nd2O3

The measurements of electrical conductivity (σ) from 300 to 1200 K and dielectric constant (ε′) from 4·2 to 1200 K of A-type Nd₂O₂ pellets are reported here. Electrical conductivity (σ) data can be explained in terms of impurity. The dielectric constant (ε′) increases slowly up to 500 K as is expected for ionic solids. The increase ofε′ becomes much faster above 500 K, which is attributed to space charge polarization of thermally generated charge carriers.     

Electrochemical performance of mixed ionic–electronic conducting oxides as anodes for solid oxide fuel cell

Mixed ionic–electronic conducting (MIEC) oxides, SrFeCo_0.5O_x, SrCo_0.8Fe_0.2O_3−δ and La_0.6Sr_0.4Fe_0.8Co_0.2O_3−δ have been synthesized and prepared on yttria-stabilized zirconia as anodes for solid oxide fuel cells. Power output measurements show that the anodes composed of such kinds of oxides exhibit modest electrochemical activities to both H₂ and CH₄ fuels, giving maximum power densities of around 0.1 W/cm² at 950°C. Polarization and AC impedance measurements found that large activation overpotentials and ohmic resistance drops were the main causes for the relative inferior performance to the Ni-YSZ anode. While interlayered with an Ni-YSZ anode, a significant improvement in the electrochemical performance was observed. In particular, for the SrFeCo_0.5O_x oxide interlayered Ni-YSZ anode, the maximum power output reaches 0.25 W/cm² on CH₄, exceeding those of both SrFeCo_0.5O_x and the Ni-YSZ, as anodes alone. A synergetic effect of SrFeCo_0.5O_x and the Ni-YSZ has been observed. Future work is needed to examine the long-term stability of MIEC oxide electrodes under a very reducing environment.     

Microstructure and electrical properties of Mn-doped barium strontium titanate thin films prepared on copper foils

Ba_0.7−xSr_0.3Mn_xTiO₃ (x = 0, 0.025, 0.05) thin films have been prepared on copper foils using sol-gel method. The films were processed in an atmosphere with low oxygen pressure so that the substrate oxidation is avoided and the formation of the perovskite phase is allowed. XRD and SEM results showed that Mn doping enhanced the crystallization of the perovskite phase in the films. The Mn substitution prevents the reduction of Ti⁴⁺ to Ti³⁺, which is supported by XPS analysis. The Ba_0.7−xSr_0.3Mn_xTiO₃ film with x = 0.025 (BSMT25) exhibits preferred dielectric behavior and a lower leakage current density among the three thin films. The dielectric constant and loss of the BSMT25 film are 1213.5 and 0.065 at 1 MHz and around zero field, which are mostly desired for embedded capacitor applications. The mechanism of Mn doping on improving the electrical properties of barium strontium titanate (BST) thin films was investigated.     

Tailoring mixed proton-electronic conductivity of BaZrO3 by Y and Pr co-doping for cathode application in protonic SOFCs

BaZr_0.8 − xPr_xY_0.2O_3 − δ (BZPYx, 0.1 ≤ x ≤ 0.4) perovskite oxides were investigated for application as cathode materials for intermediate temperature solid oxide fuel cells based on proton conducting electrolytes (protonic-SOFCs). The BZPYx reactivity with CO₂ and water vapor was evaluated by thermogravimetric and X-ray diffraction analyses, and good chemical stability was observed for each BZPYx composition. Conductivity measurements of BZPYx sintered pellets were performed as a function of temperature and p_O2 in humidified atmospheres, corresponding to cathode operating condition in protonic-SOFCs. Different conductivity values and activation energies were measured depending on the Pr content, suggesting the presence of different charge carriers. For all the compositions, the partial electronic conductivity, calculated from conductivity measurements at different p_O2, increased with increasing the temperature from 500 to 700 °C. Furthermore, the larger the Pr content, the larger the electronic conductivity. BaZr_0.7Pr_0.1Y_0.2O_3 − δ and BaZr_0.4Pr_0.4Y_0.2O_3 − δ showed mostly pure proton and electron conductivity, respectively, whereas the intermediate compositions showed mixed proton/electronic conductivity. Among the two mixed proton/electronic conductors, BaZr_0.6Pr_0.3Y_0.2O_3 − δ presented the larger conductivity, which coupled with its good chemical stability, makes this perovskite oxide a candidate cathode materials for protonic-SOFCs.     

Synthesis and characterization of apatite-type La9.67Si6-xAlxO26.5-x/2 electrolyte materials and compatible cathode materials

Apatite silicates have recently been reported as promising electrolyte materials for intermediate temperature solid oxide fuel cells (IT-SOFCs). In this work, a series of apatite-type compounds La_9.67Si_6-xAl_xO_26.5-x/2 (LSAO) with x = 0-2 are synthesized by the sol-gel process at calcining temperature of 800-900 °C. Thermal expansion coefficient, relative density and electrical conductivity of these samples with different Al doped contents are investigated. A symmetrical cell, which is composed of La_9.67Si₅AlO₂₆ electrolyte and (La_0.74Bi_0.10Sr_0.16)MnO_3+δ (LBSM) cathode, is fabricated and electrochemically characterized. LBSM cathode shows a good electrochemical performance, which proves LBSM to be a promising candidate cathode for LSAO-based electrolyte.     

Structural, thermal and conductive properties of Bi4−xMxV2O11 (M = La, Gd; 0 x 0.4) compounds

Bi_4−xM_xV₂O₁₁ (M = La, Gd) was prepared by solid state reactions. The amount of La and Gd in the (Bi_4−xM_xV₂O₁₁) was varied in the range of (0 x 0.4). The addition of La and Gd to Bi₄V₂O₁₁ electrolyte was found to stabilize the β crystalline phase for x 0.3. In addition, the phase transition corresponding β- to γ-phases are evident in the ionic conductivity plots as well as in XRD, DSC profiles of x 0.3 samples. The highest ionic conductivity was observed in Bi_3.9La_0.1V₂O₁₁ and Bi_3.8Gd_0.2V₂O₁₁ samples in the range of 10⁻³–10⁻⁴ S/cm for 700–500 °C. These results were supported by impedance spectroscopy, X-ray diffraction (XRD) and differential scanning calorimetry (DSC).     

Electrical conductivity,optical properties and mechanical stability of 3, 4, 9, 10-perylenetetracarboxylic dianhidride based organic semiconductor

The 3, 4, 9, 10-perylenetetracarboxylic dianhydride (PTCDA) doped polymer films were prepared with Polypyrrole (PPy) and Polyvinyl alcohol (PVA) polymers by solution-casting. The change in structure and chemical composition of samples was identified by XRD and FTIR respectively. The UV–visible spectroscopy demonstrates the optical characteristics and band gap properties of sample. The homogeneous morphology of sample for higher wt% of PTCDA was examined by atomic force microscopy (AFM). The differential scanning calorimetry (DSC) results demonstrate the decrease in melting temperature (T_m) and degree of crystallinity (χ_c%) of polymeric organic semiconductor. The mechanical property demonstrates the high tensile strength and improved plasticity nature. Impedance spectroscopy was evaluated to determine the conductivity response of polymeric organic semiconductor. The highest DC conductivity (2.08×10⁻³ S/m) was obtained for 10 wt% of PTCDA at 140 °C. The decrease in activation energy (E_a) represents the non-Debye process and was evaluated from the slope of ln σ_dc vs. 10³/T plot.     

High temperature oxidation behavior of interconnect coated with LSCF and LSM for solid oxide fuel cell by screen printing

The current study examined the effect of La_0.6Sr_0.4Co_0.2Fe_0.8O₃ (LSCF) and La_0.7Sr_0.3MnO₃ (LSM) coatings on the electrical properties and oxidation resistance of Crofer22 APU at 800 °C hot air. LSCF and LSM were coated on Crofer22 APU by screen printing and sintered over temperatures ranging from 1000 to 1100 °C in N₂. The coated alloy was first checked for compositions, morphology and interface conditions and then treated in a simulated oxidizing environment at 800 °C for 200 h. After measuring the long-term electrical resistance, the area specific resistance (ASR) at 800 °C for the alloy coated with LSCF was less than its counterpart coated with LSM. This work used LSCF coating as a metallic interconnect to reduce working temperature for the solid oxide fuel cell.     

Electrical conduction and dielectric properties of vanadium phosphate glasses doped with lithium

AC conductivity and dielectric studies on vanadium phosphate glasses doped with lithium have been carried out in the frequency range 0.2-100 kHz and temperature range 290-493 K. The frequency dependence of the conductivity at higher frequencies in glasses obeys a power relationship, σ_ac=Aω^s. The obtained values of the power s lie in the range 0.5≤s≤1 for both undoped and doped with low lithium content which confirms the electron hopping between V⁴⁺ and V⁵⁺ ions. For doped glasses with high lithium content, the values of s≤0.5 which confirm the domination of ionic conductivity. The study of frequency dependence of both dielectric constant and dielectric loss showed a decrease with increasing frequency while they increase with increasing temperature. The results have been explained on the basis of frequency assistance of electron hopping besides the ionic polarization of the glasses. The bulk conductivity increases with increasing temperature whereas decreases with increasing lithium content which means a reduction of the V⁵⁺.     

Influence of colloidal templates on the impedance spectroscopic behaviour of Pr0.7Sr0.3Fe0.8Ni0.2O3 for solid oxide fuel cell applications

The creation of porous materials with three-dimensional periodicity has been identified as being of potential interest for increasing the overall performance of solid oxide fuel cells (SOFC). In this work, we have investigated the formation of pore systems in the nanometer scale by replicating colloidal templates. Templating methods have been used to prepare iron-nickel-based perovskite Pr_0.7Sr_0.3Fe_0.8Ni_0.2O₃ material with nanoporous microstructure. Polymethyl methacrylate (PMMA), polystyrene (PS) and polycarboxylate (PC) microspheres with different diameters were used as pore formers. These samples were synthesized and characterized by thermogravimetric analysis, inductively coupled plasma atomic emission spectroscopy (ICP-AES), X-ray diffraction, transmission electron microscopy and field emission scanning electron microscopy. The polarization resistance of the materials was studied by Electrochemical Impedance Spectroscopy. The study demonstrated that templated porosity is maintained and highly influences on the impedance spectroscopic behaviour, being the material synthesized with policarboxylate microspheres the most interesting of the three used templates for SOFC applications.