High-temperature electrical properties of magnesiowustite Mg1 − xFexO and spinel Fe3 − x − yMgxCryO4 ceramics

Phase relationships, thermal expansion and electrical properties of Mg_1 − xFe_xO (x = 0.1-0.45) cubic solid solutions and Fe_{3 − x − y}Mg_xCr_yO_4 ± δ (x = 0.7-0.95; y = 0 or 0.5) spinels were studied at 300-1770 K in the oxygen partial pressure range from 10 Pa to 21 kPa. Increasing iron content enlarges the spinel phase stability domain at reduced oxygen pressures and elevated temperatures. The total conductivity of the spinel ceramics is predominantly n-type electronic and is essentially p(O₂)-independent within the stability domain. The computer simulations using molecular dynamics technique confirmed that overall level of ion diffusion remains low even at high temperatures close to the melting point. Temperature dependencies of the total conductivity in air exhibit a complex behavior associated with changing the dominant defect-chemistry mechanism from prevailing formation of the interstitial cations above 1370-1470 K to the generation of cation vacancies at lower temperatures, and with kinetically frozen cation redistribution in spinel lattice below 700-800 K. The average thermal expansion coefficients of the spinel ceramics calculated from dilatometric data in air vary in the range (9.6-10.0) × 10^− 6 K^− 1 at 300-500 K and (13.2-16.1) × 10^− 6 K^− 1 at 1050-1370 K. Mg_1 − xFe_xO solid solutions undergo partial decomposition on heating under oxidizing and mildly reducing conditions, resulting in the segregation of spinel phase and conductivity decrease.     

Effect of a LaSrCoO3 buffer layer on Pb1 − xLaxTi1 − x/4O3 films studied by polarized Raman spectroscopy

A confocal Raman investigation of Pb_1 − xLa_xTi_1 − x/4O₃ (PLT) thin films grown by RF magnetron sputtering on PbO_x/Pt/Ti/SiO₂/Si substrates with an intermediate LaSrCoO₃ (LSCO) layer was performed. The influence of the LaSrCoO₃ buffer layer was analyzed taking advantage of the observed Raman spectral band variation, which varied according to different manufacturing procedures. In the presence of a LSCO layer, the A1(1TO) Raman mode, which was indicative of tetragonal distortion, was pronouncedly enhanced, and a slight deviation from the (0 0 1) plane of the film was observed from the angular dependence of the polarized Raman spectral intensity. Furthermore, the spectral band variation as well as the residual stress along the in-depth direction was measured in the film from cross-sectional spectral line scans. This latter measurement showed a relaxation of the lattice mismatch in the presence of LSCO and PbO layers.     

Thermal variation of structure and electrical conductivity in Bi14WO24

Structure and electrical conductivity of Bi₁₄WO₂₄ as a function of temperature have been examined by X-ray and neutron powder diffraction, a.c. impedance spectroscopy and differential thermal analysis. The room temperature structure was successfully refined using a monoclinic subcell model in space group I2/m. However, additional reflections in the neutron data are consistent with a large supercell of dimensions a = 17.3780(1) Å, b = 17.3891(1) Å, c = 26.1785(2) Å and β = 90.270(1)°, as previously proposed. Transitions to tetragonal and cubic phases are observed at ca. 35 °C and 780 °C, respectively. The structure of the high temperature polymorph is confirmed as a fully disordered δ-Bi₂O₃ type phase. Analysis of the defect structure is consistent with a predominantly tetrahedral environment for tungsten, as seen at low temperatures. The conductivity behaviour is correlated with the appearance of the δ-phase at high temperatures and exhibits a value of 0.97 S cm^− 1 at 800 °C.     

Conductivity and sintering property of LaNi1 − xFexO3 ceramics prepared by Pechini method

Preparation of LaNi_1 − xFe_xO₃, which is one of the candidate materials of solid oxide fuel cell cathode, current collecting layer and interconnect coating was examined with Pechini method and solid state reaction method. Single phase LaNi_1 − xFe_xO₃ with large Ni content has successfully been prepared by low temperature sintering as 750 °C with Pechini method, whereas large amount of raw materials has remained with solid state reaction method by sintering at the same temperature. It can be ascribed to more homogenous cation distribution in raw powder material prior to sintering with Pechini method. It has also been revealed that LaNi_1 − xFe_xO₃ with x lower than 0.3 is thermodynamically unstable in air above 1000 °C. LaNi_0.6Fe_0.4O₃ showed superior property as cathode material with high electrical conductivity, thermodynamic stability and appropriate sintering property.     

Magnetic characterization of Bi(Fe1 − xMnx)O3

Bi(Fe_1 − xMn_x)O₃ ceramics (x up to 0.3) were prepared by rapid sintering. Weak ferromagnetism with two magnetic anomalies at low temperatures was observed for Bi(Fe_0.95Mn_0.05)O₃ and Bi(Fe_0.9Mn_0.1)O₃. From temperature-dependent magnetic relaxation measurements, the anomalies at 20 K and 100 K are related to the freezing of cluster spin glass.     

Influence of Co doping content on its valence state in Zn1−xCoxO (0 ≤ x ≤ 0.15) thin films

Zn_1−xCo_xO (0 ≤ x ≤ 0.15) thin films grown on Si (1 0 0) substrates were prepared by a sol-gel technique. The effects of Co doped on the structural, optical properties and surface chemical valence states of the Zn_1−xCo_xO (0 ≤ x ≤ 0.15) films were investigated by X-ray diffraction (XRD), ultraviolet-visible spectrometer and X-ray photoelectron spectroscopy (XPS). XRD results show that the Zn_1−xCo_xO films retained a hexagonal crystal structure of ZnO with better c-axis preferred orientation compared to the undoped ZnO films. The optical absorption spectra suggest that the optical band-gap of the Zn_1−xCo_xO thin films varied from 3.26 to 2.79 eV with increasing Co content from x = 0 to x = 0.15. XPS studies show the possible oxidation states of Co in Zn_1−xCo_xO (0 ≤ x ≤ 0.05), Zn_0.90Co_0.10O and Zn_0.85Co_0.15O are CoO, Co₃O₄ and Co₂O₃, with an increase of Co content, respectively.     

Half-metallic antiferromagnetism in the ordered Cr1 − xCaxSb alloy from first-principles calculations

Compared to half-metallic ferromagnets, half-metallic antiferromagnets (precisely called half-metallic fully compensated ferrimagnets) are more promising candidates for spintronic applications since their zero magnetization leads to lower stray fields and thus tiny energy losses. Using the first-principles calculations, we have systematically investigated the electronic and magnetic properties of the ordered Cr_1 − xCa_xSb alloy. It is found that Cr_1 − xCa_xSb with x=0.125, 0.25, 0.5 and 0.75 all are half-metals like zinc-blende CrSb and CaSb. Interestingly, Cr_0.25Ca_0.75Sb is a half-metallic antiferromagnet with complete spin polarization, and the half-metallic antiferromagnetism is robust against the lattice compression and expansion and the choice of electronic exchange and correlation functional.     

Effect of Fe substitution on magnetocaloric effect in La0.7Sr0.3Mn1−xFexO3 (0.05≤x≤0.20)

We have studied the effect of Fe substitution on magnetic and magnetocaloric properties in La_0.7Sr_0.3Mn_1−xFe_xO₃ (x=0.05, 0.07, 0.10, 0.15, and 0.20) over a wide temperature range (T=10-400 K). It is shown that substitution by Fe gradually decreases the ferromagnetic Curie temperature (T_C) and saturation magnetization up to x=0.15 but a dramatic change occurs for x=0.2. The x=0.2 sample can be considered as a phase separated compound in which both short-range ordered ferromagnetic and antiferromagnetic phases coexist. The magnetic entropy change (−ΔS_m) was estimated from isothermal magnetization curves and it decreases with increase of Fe content from 4.4 J kg⁻¹ K⁻¹ at 343 K (x=0.05) to 1.3 J kg⁻¹ K⁻¹ at 105 K (x=0.2), under ΔH=5 T. The La_0.7Sr_0.3Mn_0.93Fe_0.07O₃ sample shows negligible hysteresis loss, operating temperature range over 60 K around room temperature with refrigerant capacity of 225 J kg⁻¹, and magnetic entropy of 4 J kg⁻¹ K⁻¹ which will be an interesting compound for application in room temperature refrigeration.     

Thermoelectric properties of the Bi2−xYxRu2O7 (x=0-2) pyrochlores

Electrical conductivity and Seebeck coefficient for the Bi_2−xY_xRu₂O₇ pyrochlores with x=0.0,0.5,1.0,1.5,2.0 were measured in the temperature range of 473-1073 K in air. With increasing Bi content, the temperature dependence of the electrical conductivity changed from semiconducting to metallic. The signs of the Seebeck coefficient were positive in the measured temperature range for all the samples, indicating that the major carriers were holes. The temperature dependence of the Seebeck coefficient for the Y₂Ru₂O₇ indicated the thermal activation-type behavior of the holes, while that for the Bi_2−xY_xRu₂O₇ with x=0.0-1.5 indicated the itinerant behavior of the holes. The change in the conduction behavior from semiconductor to metal with increasing Bi content is consistent with the increase in the overlap between the Ru4d t_2g and O2p orbitals, but the mixing of Bi6s, 6p states at E_F may not be ruled out. The thermoelectric power factors for the Bi_2−xY_xRu₂O₇ with x=1.5 and 2.0 were lower than 10⁻⁵ W m⁻¹ K⁻² and those with x=0.0,0.5,1.0 were around 1-3×10⁻⁵ W m⁻¹ K⁻².     

Synthesis and ferroelectric properties of bismuth layer-structured (Bi7−xSrx)(Fe3−xTi3+x)O21 solid solutions

Bismuth layer-structured (Bi_7−xSr_x)(Fe_3−xTi_3+x)O₂₁ (BSFT) ceramics were synthesized and the ferroelectric properties and crystal structure were investigated. X-ray powder diffraction profiles and refinement of the lattice parameters indicated single phase BSFT was obtained in the composition range 0-1.5. The lattice parameter b of BSFT remained almost constant, while a slight decrease in the lattice parameter a was observed by the Sr and Ti substitution for Bi and Fe, respectively, which indicated an increase in the orthorhombicity. The dependence of the BSFT lattice parameter on temperature implied a phase transition from the orthorhombic to the tetragonal phase, which was in good agreement with the Curie temperature. The remnant polarization P_r, of BSFT was significantly improved by the Sr and Ti substitution for Bi and Fe, and ranged from 9 to 16 μC/cm², although no remarkable variation in the coercive field E_c was observed. As a result, a well-saturated P-E hysteresis loop of BSFT ceramic was obtained at x=0.5 with a P_r of 30 μC/cm at an applied voltage of 280 kV/cm.     

AlN, GaN, AlxGa1 − xN nanotubes and GaN/AlxGa1 − xN nanotube heterojunctions

Semiconductor optoelectronic devices based on GaN and on InGaN or AlGaN alloys and superlattices can operate in a wide range of wavelengths, from far infrared to near ultraviolet region. The efficiency of these devices could be enhanced by shrinking the size and increasing the density of the semiconductor components. Nanostructured materials are natural candidates to fulfill these requirements. Here we use the density functional theory to study the electronic and structural properties of (10,0) GaN, AlN, Al_xGa_1 − xN nanotubes and GaN/Al_xGa_1 − xN heterojunctions, 0<x<1. The Al_xGa_1 − xN nanotubes exhibit direct band gaps for the whole range of Al compositions, with band gaps varying from 3.45 to 4.85 eV, and a negative band gap bowing coefficient of −0.14 eV. The GaN/Al_xGa_1 − xN nanotube heterojunctions show a type-I band alignment, with the valence band offsets showing a non-linear dependence with the Al content in the nanotube alloy. The results show the possibility of engineering the band gaps and band offsets of these III-nitrides nanotubes by alloying on the cation sites.     

Anomalous behavior of ultrasonic properties near 50 K in Rb0.30MoO3 and Rb0.30(Mo1−xVx)O3

Depending on the temperature, the charge density wave (CDW) nonlinear conductivity of the blue bronzes A_0.30MoO₃ (A=K, Rb) shows two different regimes: a strongly damped motion above ∼50 K and motion with almost no damping below ∼50 K. In a search for an elastic signature of this CDW behaviour, we performed ultrasonic measurements on Rb_0.30MoO₃ and Rb_0.30(Mo_1−xV_x)O₃ single crystals between 4 K and 300 K. In Rb_0.30MoO₃, at T∼50 K, upon cooling, a large increase of the sound velocity is observed. The ultrasonic attenuation coefficient shows an increase down to 50 K followed by a plateau. In Rb_0.30(Mo_1−xV_x)O₃ (x=0.4 at%) the anomaly broadens and is shifted towards higher temperatures. The results are discussed in terms of CDW glass.     

Structural,electronic and optical properties of CdxZn1 − xS alloys from first-principles calculations

Structural, electronic and optical properties as well as structural phase transitions of ternary alloy Cd_xZn_1 − xS have been investigated using the first-principles calculations based on the density functional theory. We found that the crystal structure of Cd_xZn_1 − xS alloys transforms from wurtzite to zinc blende as Cd content of x=0.83$x=0.83$. Effect of Cd content on electronic structures of Cd_xZn_1 − xS alloys has been studied. The bandgaps of Cd_xZn_1 − xS alloys with wurtzite and zinc blende structures decrease with the increase of Cd content. Furthermore, dielectric constant and absorption coefficient also have been discussed in detail.     

Effect of electric field on electrocaloric effect in Pb(Zr1 − xTix)O3 solid solution

A thermodynamic analysis is employed to investigate the intrinsic electrocaloric effect of Pb(Zr_1 − xTi_x)O₃ solid solution system under the different electric field. Theoretical analysis indicates that Pb(Zr_1 − xTi_x)O₃ system has the giant electrocaloric coefficient and the large adiabatic temperature change near its ferroelectric Curie temperature. The applied electric field decreases not only the electrocaloric coefficient but also its temperature dependence. Furthermore, it increases the adiabatic temperature change as well as its dependence of temperature. The temperature corresponding to the maximum of electrocaloric coefficient and adiabatic temperature change increases with the enhancement of electric field because of its first-order phase transition between ferroelectric phase and paraelectric phase.     

The effect of Mn substitution on thermoelectric properties of Ca3MnxCo4−xO9 at low temperatures

The effects of partial substitution of Mn for Co on the thermoelectric properties of Ca₃Mn_xCo_4−xO₉ (x=0, 0.03, 0.9), prepared by sol-gel process, were investigated at the temperatures from 380 K down to 5 K. The results indicate that the substitution of Mn for Co results in increase in thermopower at temperatures >∼80 K, and substantial (23-31% at 300 K) decrease in lattice thermal conductivity in the whole temperature range investigated. The temperature behavior of ZT suggests that Ca₃Mn_xCo_4−xO₉ with light Mn substitution would be a promising candidate for high-temperature thermoelectric applications.     

Electrical characteristics of hole resonant tunneling diodes with high Ge fraction (x > 0.4) Si/strained Si1−xGex/Si(1 0 0) heterostructure

Effectiveness of a Ge fraction modulated spacer in hole resonant tunneling diodes (RTDs) with Si/strained Si_1−xGe_x heterostructures epitaxially grown on Si(1 0 0) was investigated to improve the electrical characteristics at higher temperatures. Electrical characteristics measured for 30 RTDs, with the modulated spacer at higher Ge fraction (x = 0.48) on a single wafer, show that the deviation of the peak current and voltage at the resonant peak falls in ranges of ±25% and ±10%, respectively. For the RTDs, negative differential conductance (NDC) characteristics are obtained even at higher temperatures around 230 K than that for the RTDs with x = 0.42. The result indicates that the introduction of higher Ge fraction is effective for NDC in RTD at higher temperature.     

Photoluminescence investigation of ferromagnetic Ga1−xMnxN layers with GaN templates grown on sapphire (0 0 0 1) substrates

We have investigated the temperature and composition dependent photoluminescence (PL) spectra in Ga_1−xMn_xN layers (where x ≈ 0.1-0.8%) grown on sapphire (0 0 0 1) substrates using the plasma-enhanced molecular beam epitaxy technique. The efficient PL is peaked in the red (1.86 eV), yellow (2.34 eV), and blue (3.29 eV) spectral range. The band-gap energy of the Ga_1−xMn_xN layers decreased with increasing temperature and manganese composition. The band-gap energy of the Ga_1−xMn_xN layers was modeled by the Varshni equation and the parameters were determined to be α = 2.3 × 10⁻⁴, 2.7 × 10⁻⁴, 3.4 × 10⁻⁴ eV/K and β = 210, 210, and 230 K for the manganese composition x = 0.1%, 0.2%, and 0.8%, respectively. As the Mn concentration in the Ga_1−xMn_xN layers increased, the temperature dependence of the band-gap energy was clearly reduced.     

The size and strain effects on the Raman spectra of Ce1−xNdxO2−δ (0≤x≤0.25) nanopowders

Ultrafine Ce_1−xNd_xO_2−δ (x=0-0.25) powders were synthesized by self-propagating room temperature synthesis. Raman spectra were measured at room temperature in the 300-700 cm⁻¹ spectral range. The shift and asymmetric broadening of the Raman F_2g mode at about 454 cm⁻¹ in pure and doped ceria samples could be explained with combined size and inhomogenous strain effects. Increased concentration of O²⁻ vacancies with doping is followed by an appearance of new Raman feature at about 545 cm⁻¹.     

A study on magnetoelastic properties of Tb3 (Fe28−xCox) V1.0 (x=0, 3, 6) compounds

In this work, The magnetoelastic properties of polycrystalline samples of Tb₃ (Fe_28−xCo_x) V_1.0 (x=0, 3, 6) intermetallic compounds are investigated by means of linear thermal expansion and magnetostriction measurements in the temperature range of 77–515 K under applied magnetic fields up to 1.5 T. The linear thermal expansion increases with the Co content. The well-defined anomalies observed in the linear thermal expansion coefficients for Tb₃ (Fe_28−xCo_x) V_1.0 (x=0, 3, 6) compounds are associated with the magnetic ordering temperature for x=0 and spin reorientation temperatures for x=3, 6. Below transition temperatures, the value of the longitudinal magnetostriction (λ_Pa) at 1.6 T increases with Co content.     

Effect of Cr substitution on the multiferroic properties of BiFe1 − xCrxO3 compounds

Single-phase BiFe_1 − xCr_xO₃ (x=0, 0.05 and 0.1) compounds are synthesized by a sol-gel process. The lattice parameters decrease and the magnetizations increase with the Cr content. Moreover, the magnetoelectric coupling between magnetic order and ferroelectric order at room temperature was enhanced.