Characteristics of spherical-shaped Li4Ti5O12 anode powders prepared by spray pyrolysis

Spherical-shaped Li₄Ti₅O₁₂ anode powders with a mean size of 1.5 μm were prepared by spray pyrolysis. The precursor powders obtained by spray pyrolysis had no peaks of crystal structure of Li₄Ti₅O₁₂. The powders post-treated at temperatures of 800 and 900 °C had the single phase of spinel Li₄Ti₅O₁₂. The powders post-treated at a temperature of 1000 °C had main peaks of the Li₄Ti₅O₁₂ phase and small impurity peaks of Li₂Ti₃O₇. The spherical shape of the precursor powders was maintained after post-treatment at temperatures below 800 °C. The Brunauer-Emmett-Teller (BET) surface areas of the Li₄Ti₅O₁₂ anode powders post-treated at temperatures of 700, 800 and 900 °C were 4.9, 1.6 and 1.5 m²/g, respectively. The initial discharge capacities of Li₄Ti₅O₁₂ powders were changed from 108 to 175 mAh/g when the post-treatment temperatures were changed from 700 to 1000 °C. The maximum initial discharge capacity of the Li₄Ti₅O₁₂ powders was obtained at a post-treatment temperature of 800 °C, which had good cycle properties below current densities of 0.7 C.     

Synthesis and performance of core-shell structured ZnO/In2O3 composites in situ growth

Core-shell structured ZnO/In₂O₃ composites were successfully synthesized via situ growth method. Phase structure, morphology, microstructure and property of the products were investigated by X-ray diffraction (XRD), TG-DTA, field emission scanning electron microscopy (FESEM), energy-dispersive spectrometry (EDS), transmission electron microscope (TEM) and photoluminescence (PL). Results show that the core-shell structures consist of spindle-like ZnO with about 800 nm in length and 200 nm in diameter, and In₂O₃ particles with a diameter of 50 nm coated on the surface of ZnO uniformly. HMTA plays an important role in the formation of core-shell structures and the addition of In₂O₃ has a great effect on PL spectrum. Possible mechanism for the formation of core-shell structures is also proposed in this paper.     

Electrostatic spray deposition of spinel Li4Ti5O12 thin films for rechargeable lithium batteries

Spinel Li₄Ti₅O₁₂ thin films are important for the fabrication of rechargeable lithium microbatteries. Porous thin films of Li₄Ti₅O₁₂ were prepared by electrostatic spray deposition (ESD) technique with lithium acetate and titanium butoxide as the precursors. The structures of these films were analyzed by scanning electron microscopy and X-ray diffraction. Coin-type cells with a liquid electrolyte were made with the Li₄Ti₅O₁₂ films against metallic lithium. Their electrochemical performance was investigated by means of galvanostatic cell cycling, cyclic voltammetry and Ac impedance spectroscopy. It was found that pure spinel phase of Li₄Ti₅O₁₂ was obtained. After annealing at the optimal temperature of 700 °C, the films can deliver a reversible specific capacity of about 150 mAh/g with excellent capacity retention after 70 cycles. Their electrochemical characteristics were quite comparable with those of the Li₄Ti₅O₁₂ laminate electrodes containing carbon black additive.     

Molten salt synthesis of Li1 + x (Ni0.5Mn0.5)1 − xO2 as cathode material for Li-ion batteries

Li_1 + x(Ni_0.5Mn_0.5)_1 − xO₂ cathode material for Li-ion batteries has been prepared by a molten salt method using Li₂CO₃ salt. The influences of synthetic temperature and time have been intensively investigated. It is easy to obtain materials with a hexagonal α-NaFeO₂ structure except broad peaks between 20° and 25°. Nickel in Li_1 + x(Ni_0.5Mn_0.5)_1 − xO₂ is oxidized to a trivalent state while manganese maintained a tetravalent state. It is found that the discharge capacities of all samples increase with cycling. The sample prepared at 850 °C for 5 h has a discharge capacity of 130 mAh g^− 1 between 2.5 and 4.5 V versus V_Li+/Li at a specific current of 0.13 mA cm^− 2 after 50 cycles at 25 °C.     

Electron spin resonance of diluted solid solutions of MnO2 in Y2O3

Electron spin resonance spectra of Mn²⁺ in diluted solid solutions of MnO₂ in Y₂O₃ have been studied at room temperature for Mn concentrations between 0.20 and 2.00 mol%. Isolated Mn²⁺ ions in sites with two different symmetries were observed, as well as Mn²⁺ ions coupled by the exchange interaction. The relative concentration of isolated to coupled Mn²⁺ ions decreases with increasing manganese concentration. The results are consistent with the assumption that the manganese ions occupy preferentially the C₂ symmetry sites. A theoretical calculation based on this model yields an effective range of the exchange interaction between Mn²⁺ ions of 0.53 nm, of the same order as that of Mn²⁺ ions in CaO.     

Correlation between Li+ adsorption capacity and the preparation conditions of spinel lithium manganese precursor

Spinel lithium manganese oxides can be used as Li⁺ adsorbent with topotactical extraction of lithium. In this paper, the solid state methods were introduced to prepare spinel lithium manganese precursors with Li₂CO₃ and LiOH·H₂O as different Li sources. The Li⁺ uptake was studied to clarify the correction between Li⁺ adsorption capacity and the preparation conditions of precursors, including different Li sources, Li/Mn mole ratios and heating time. The results indicated that the Li⁺-extracted materials prepared with LiOH·H₂O and MnCO₃ usually have higher Li⁺ adsorption capacity than Li₂CO₃ and MnCO₃, and an ascending trend was found in Li⁺ uptake with increasing Li/Mn mole ratio in the preparation of the precursor, but it is not proportional. The Mn₂O₃ impurities could be the primary reason for decreasing Li⁺ adsorption capacity. Furthermore, it is concluded that the Li⁺-extracted materials obtained from spinel manganese oxides synthesized with Li/Mn = 1.0 can serve as selective Li⁺ absorbents due to its high selectivity and large adsorption capacity.     

Muon spectroscopy for studying magnetism and protons and lithium dynamics in spinel manganese oxides

Polarised positive muons can be implanted into any type of material and rapidly thermalize, then the local magnetic environment dictates the evolution of muon spin vectors and provokes the muon depolarisation. The muon spin relaxation (μSR) technique provides interesting information on magnetism and spin dynamics in spinel lithium manganates insertion compounds. In this work, we compare the behaviour of muons into a lithium-rich spinel manganese oxide and its lithium extracted product. The chemical extraction of lithium from Li_1.33Mn_1.67O₄, where all the manganese is Mn^IV, is essentially a lithium by proton ion exchange process to give a protonated manganese oxide with spinel structure, H⁺–MnO₂. Muons clearly have showed the presence of protons in H⁺–MnO₂, and the movement of lithium ions or protons at increasing temperatures in both samples. Muons are quasi-static in these compounds, and they are located both in ‘regular’ lithium and proton sites and also in interstitial sites of the spinel structure, these latter being used during diffusion of lithium ions. Below 50 K, static muons behave as in a paramagnet, where Mn magnetic spins are slowing down and ordering near 6 and 14 K in the protonated and lithiated spinels, respectively.     

Synthesis of spinel lithium titanate anodes incorporated with rutile titania nanocrystallites by spray drying followed by calcination

Lithium insertion into spinel Li₄Ti₅O₁₂ incorporated with rutile TiO₂ was investigated in order to clarify the redox mechanism responsible for the first plateau at 1.5 V vs. Li/Li⁺. Spherical Li₄Ti₅O₁₂ powders with an average diameter of 2-3 μm can be achieved by spray drying followed by sintering process. The Li/Ti molar ratio in the precursor is selected as the factor for preparing spinel Li₄Ti₅O₁₂ powders with different concentrations of rutile TiO₂. The specific capacity from the first plateau at 1.5 V contributes to the major portion in the overall capacity. The rutile TiO₂ in spinel Li₄Ti₅O₁₂ anodes tends to improve the specific capacity at the first plateau. This can be attributed to two possible reasons: (i) rutile TiO₂ provides an additional number of sites (i.e., oxygen octahedral vacancy in rutile TiO₂) for the Li insertion, and (ii) less amount of residual Li oxides results in high electronic conductivity. The Li₄Ti₅O₁₂ anodes display high rate capability with low irreversible capacity, indicating good reversibility of insertion/de-insertion of Li ions. The results presented in this work show unambiguously that the presence of rutile TiO₂ in spinel Li₄Ti₅O₁₂ has a positive effect on the performance promotion of Li₄Ti₅O₁₂ anodes.     

Preparation and characterizations of SiO2-coated nanoparticles of Mn0.4Zn0.6Fe2O4

Core/shell nanoparticles consisting of a magnetic core of zinc-substituted manganese ferrite (Mn_0.4Zn_0.6Fe₂O₄) and a shell of silica (SiO₂) are prepared by a sol-gel method using tetraethyl orthosilicate (TEOS) as a precursor material for silica and salts of iron, manganese and zinc as the precursor of the ferrite. Three weight percentages of the shell materials of SiO₂ are used to prepare the coated nanoparticles. The X-ray diffractograms (XRD) of the coated and uncoated magnetic nanoparticles confirmed that the magnetic nanoparticles are in their mixed spinel phase in an amorphous matrix of silica. Particles sizes of the samples annealed at different temperatures are estimated from the width of the (3 1 1) line of the XRD pattern using the Debye-Sherrer equation. The information regarding the crystallographic structure together with the particles sizes extracted from the high-resolution transmission electron microscopy (HRTEM) of a few selected samples are in agreement with those obtained from the XRD. HRTEM observations revealed that particles are coated with silica. The calculated thickness is in agreement with that obtained from the HRTEM pictures. Hysteresis loops observed in the temperature range 300 down to 5 K and Mössbauer spectra at room temperature indicate superparamagnetic relaxation of the nanoparticles.     

Organic acid assisted solid-state synthesis of Li1.2Ni0.16Co0.08Mn0.56O2 nanoparticles as lithium ion battery cathodes

Lithium-rich layered oxide Li_1.2Ni_0.16Co_0.08Mn_0.56O₂ can be referred as a crystalline mixture of Li₂MnO₃ and LiNi_0.4Co_0.2Mn_0.4O₂ at equal molar ratio. In the paper, the solid state reaction of M(AC)₂·4H₂O (M = Mn, Co and Ni) and LiOH·H₂O has been performed to obtain nanocrystalline Li_1.2Ni_0.16Co_0.08Mn_0.56O₂ using a small molecular organic acid (i.e., oxalic acid (OA), citric acid (CA) or tartaric acid (TA)) as additive. The introduction of organic acids can help to improve the layered structure and inhibit the particle growth of Li_1.2Ni_0.16Co_0.08Mn_0.56O₂, and the different organic acids exert distinct influences on the structural and electrochemical properties of Li_1.2Ni_0.16Co_0.08Mn_0.56O₂. In detail, the nanoparticles obtained in the presence of OA have the smallest average size of 50–150 nm, which correspondingly exhibit the highest initial discharge capacity of 267.52 mAh g⁻¹ at 0.1C and the best high-rate capability (e.g., 152.22 mAh g⁻¹, 5C) when applied as a lithium ion battery cathode. Furthermore, the active substance obtained from TA shows the best cycling stability and a discharge capacity of 202.42 mAh g⁻¹ can be retained after 50 cycles at 0.5C.     

Synthesis and electrochemical performances of Li4Ti4.95Al0.05O12/C as anode material for lithium-ion batteries

Spinel compounds Li₄Ti_5−xAl_xO₁₂/C (x=0, 0.05) were synthesized via solid state reaction in an Ar atmosphere, and the electrochemical properties were investigated by means of electronic conductivity, cyclic voltammetry, and charge-discharge tests at different discharge voltage ranges (0-2.5 V and 1-2.5 V). The results indicated that Al³⁺ doping of the compound did not affect the spinel structure but considerably improved the initial capacity and cycling performance, implying the spinel structure of Li₄Ti₅O₁₂ was more stable when Ti⁴⁺ was substituted by Al³⁺, and Al³⁺ doping was beneficial to the reversible intercalation and deintercalation of Li⁺. Al³⁺ doping improved the reversible capacity and cycling performance effectively especially when it was discharged to 0 V.     

Electrochemical behaviour of nano-sized spinel LiMn2O4 and LiAlxMn2−xO4 (x=Al: 0.00-0.40) synthesized via fumaric acid-assisted sol-gel synthesis for use in lithium rechargeable batteries

Pristine spinel LiMn₂O₄ and LiAl_xMn_2−xO₄ (x=Al: 0.00-0.40) with sub-micron sized particles have been synthesized using fumaric acid as chelating agent by sol-gel method. The synthesized samples were subjected to thermogravimetric analysis (TGA), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and cyclic voltammetry (CV) and galvanostatic cycling studies. The TGA curve of the gel shows several weight-loss regions stepwise amounting to 55% till 800 °C attributed to the decomposition of the precursors. Calcination to higher temperatures (800 °C) yields pure-phase spinel (LiAl_xMn_2−xO₄), as it is evident from the high-intensity XRD reflections matching to the standard pattern. SEM and TEM studies confirm that the synthesized grains are of uniform regular surface morphology. FT-IR studies show stretching and bending vibration bands of Li-O, Li-Al-Mn-O. LiAl_0.1Mn_1.90O₄ spinel was found to deliver discharge capacity of 139 mA h/g during the first cycle with columbic efficiency of 97%. LiAl_0.1Mn_1.90O₄ spinel exhibits the high cathodic peak current indicating better electrochemical performance. Low doping (x=0.1) of Al is found to be beneficial in stabilizing the spinel structure.     

XRD and XPS characterization of mixed valence Mn3O4 hausmannite thin films prepared by chemical spray pyrolysis technique

Spray pyrolysis technique has been employed successfully for the synthesis of single phase mixed valence spinel hausmannite (Mn₃O₄) thin films using alcoholic start solution of manganese acetate (Mn(CH₃COO)₂·4H₂O) on pyrex glass substrates at atmospheric pressure using air as a carrier gas. Thermal decomposition of the precursor in the temperature range 320-490 °C led to the formation of Mn₃O₄ phase as revealed from the thermogravimetry analysis. Prepared samples are characterized by X-ray diffraction that shows spinel structure with space group I4₁/amd. Pure and well crystallized specimen is subjected to X-ray photoelectron spectroscopy for the surface chemistry investigation of these systems at a molecular level. Surface Mn/O ratio is compared to the bulk composition of the sample. Atomic force micrographs revealed that the morphology and the surface grains of the films largely influenced by the substrate temperature.     

First principles study of the electron structures of CaCu3Mn4O12 and CaCu3Ti4O12

The electronic structures of CaCu₃Mn₄O₁₂ and CaCu₃Ti₄O₁₂ are investigated from HF SCF LCAO calculation. In CaCu₃Mn₄O_12, the band and the density of states show a spin asymmetric ferrimagnetic character with a small energy gap. The Mn spin is anti-aligned with the Cu spin, and the total spin moment is 9 μ_B. Our calculation correctly reproduces the observed antiferromagnetic insulating character of CaCu₃Ti₄O₁₂. The gap in the band structure, which is 2.15 eV, reasonably agrees with the experimental value 1.5 eV. The electron density populations at different planes show clearly that the electron density has symmetric character. A tilted Mn(Ti) orbital implies a typical tilted three-dimensional network of MnO₆ (TiO₆) octahedra due to doping of the Jahn–Teller ion Cu. There is no covalency between Ca, Cu and Mn(Ti) atoms. In contrast, there are stronger bonds and somewhat likely covalency between Cu and O atoms, and also between Mn(Ti) and O atoms.     

Synthesis and crystallographic studies of garnet-type AgCa2Mn2V3O12 and NaPb2Mn2V3O12

High-purity powder specimens of AgCa₂Mn₂V₃O₁₂ and NaPb₂Mn₂V₃O₁₂ have been successfully synthesized by solid-state chemical reaction. The Rietveld refinements from X-ray powder diffraction data verified that these compounds have the garnet-type structure (space group , No. 230) with the lattice constant of a=12.596(2) Å for AgCa₂Mn₂V₃O₁₂ and a=12.876(2) Å for NaPb₂Mn₂V₃O₁₂. Calculation of the bond valence sum supported that Mn is divalent and V is pentavalent in these garnets. Estimation of the quadratic elongation and the bond angle variance showed that the distortions of the MnO₆ octahedra and the VO₄ tetrahedra are significantly suppressed. Our new results of AgCa₂Mn₂V₃O₁₂ and NaPb₂Mn₂V₃O₁₂ are compared to those of AgCa₂M₂V₃O₁₂ and NaPb₂M₂V₃O₁₂ (M=Mg, Co, Ni, Zn).     

Nanocrystalline and long cycling LiMn2O4 cathode material derived by a solution combustion method for lithium ion batteries

A nanostructured LiMn₂O₄ spinel phase is used as a cathode for 4 V lithium batteries and is prepared by solution combustion synthesis using urea as a fuel. Lithium-manganese oxides have received more increasing attention in recent years as high-capacity intercalation cathodes for rechargeable lithium-ion batteries. Nanostructured electrodes have been shown to enhance the cell cyclability. For optimum synthesis, the spinel LiMn₂O₄ showed that the optimal heat treatment protocol was a 10 h calcination at 700 °C, which sustained 229 cycles between 3.0 and 4.3 V at a charge-discharge rate of 0.1 °C before reaching an 80% charge retention cut-off value. X-ray diffraction and electron diffraction pattern investigations demonstrate that all the LiMn₂O₄ products are a spinel phase crystal. TEM micrographs show the prepared products were highly crystalline with an average particle size of 20-50 nm. Cyclic voltammetry shows the absence of phase transitions in the samples ensures negligible strain, resulting in a longer cycle life. This work shows the feasibility of the solution combustion method for obtaining manganese oxides with nano-architecture and high cyclability, and suggests it is a promising method for providing small diffusion pathways that improve lithium-ion intercalation kinetics and minimize surface distortions during cycling.     

Structural, transport and electrochemical properties of LiNi1 − yCoyMn0.1O2 and Al, Mg and Cu-substituted LiNi0.65Co0.25Mn0.1O2 oxides

LiNi_{1 - y − z}Co_yMn_zO₂ (y = 0.25, 0.35, 0.5, 0.6; z = 0.1, 0.2), LiNi_0.63Cu_0.02Co_0.25Mn_0.1O₂, LiNi_0.65Co_0.25Mn_0.08Al_0.02O₂, LiNi_0.65Co_0.25Mn_0.08Mg_0.02O₂ and LiNi_0.65Co_0.25Mn_0.08Al_0.01Mg_0.01O₂ cathode materials were synthesized by a soft chemistry EDTA-based method. Structural and transport properties of pristine and delithiated materials (Li_xNi_0.65Co_0.25Mn_0.1O₂, Li_xNi_0.55Co_0.35Mn_0.1O₂ and LiNi_0.63Cu_0.02Co_0.25Mn_0.1O₂ oxides) are presented. In the considered group of oxides there is no correlation between electrical conductivity and the a parameter (M-M distance in the octahedra layers). The results of electrochemical performance of cathode materials are presented. The best stability during first 10 cycles was obtained for Li/Li_xNi_0.63Cu_0.02Co_0.25Mn_0.1O₂ cell due to enhanced kinetics of intercalation process.     

Synthesis and magnetic properties of antiferromagnetic Li2MnO3 nanoribbons

Single-crystalline Li₂MnO₃ nanoribbons have been synthesized via the precursor template Na_0.44MnO₂ nanoribbons in LiNO₃-LiCl eutectic molten salt. The as-prepared Li₂MnO₃ nanoribbons are characterized by a range of methods including X-ray diffractometer, scanning electron microscope, transmission electron microscope, energy dispersive X-ray spectroscopy, and selected-area electron diffraction techniques. Magnetization measurements show that the Li₂MnO₃ nanoribbons present weak ferromagnetism, spin-glass-like behavior, and exchange bias effect at low temperature. The magnetic behaviors of Li₂MnO₃ nanoribbons can be interpreted based on a core-shell model.     

Spectroscopic and magnetic studies of manganese ions in ZnO-Sb2O3-B2O3 glass system

ZnO-Sb₂O₃-B₂O₃ glasses containing different concentrations of MnO ranging from 0 to 1.0 mol% were prepared. A number of studies, viz. optical absorption, infrared and ESR spectra and magnetic susceptibility, were carried out as a function of manganese ion concentration. The analysis of the results indicate that manganese ions mostly exist in Mn²⁺ state in these glasses when the concentration of MnO≤0.6 mol% and above this concentration, these ions seem to exist in Mn³⁺ state in the glass network.