SnO2TiO2 复合半导体纳米薄膜的研究进展

本文概述了SnO₂TiO₂ 复合半导体纳米薄膜的发展历史和研究现状,对比分析了“混合”、“核壳”和“叠层”3 种复合薄膜的结构和性能特点,着重论述了叠层结构的SnO₂ /TiO₂复合薄膜的光电化学和光催化特性。结合作者的研究工作,探讨了SnO₂ /TiO₂双层复合薄膜上下层厚度对其光催化活性的影响,指出复合薄膜光催化活性的提高可归因于电子从TiO₂ 向SnO₂ 的迁移。最后对SnO₂ /TiO₂复合薄膜的局限性和发展潜势做一简要分析,强调了该复合薄膜本身的应用特点。     

基于SnO2为修饰层的Au-Pt / SnO2 / Au复合电极研究

用真空镀膜法在Au电极上沉积SnO₂薄膜，在HAuCl₄和H₂PtCl₄的混合溶液中利用直接还原法，将Au-Pt双金属纳米颗粒组装在SnO₂ / Au电极上，得到Au-Pt / SnO₂ / Au复合电极。采用SEM、TEM、XPS及CV曲线测定对Au-Pt / SnO₂ / Au复合电极进行了表征。结果表明:复合电极上双金属纳米颗粒分布均匀，粒子粒径约为25 nm左右。SnO₂作为修饰层以配位键与双金属纳米粒子结合。Au-Pt / SnO₂ / Au复合电极具有良好对甲醇氧化的电化学性能。     

SnO2纳米带的水辅助生长与表征

以高纯Sn粉为原料，采用水辅助生长法在850 ℃下合成了SnO₂纳米带，用SEM、TEM、XRD、EDX、 HRTEM和SAED对其形貌、结构和成份进行了表征，对SnO₂纳米带的光致发光和红外谱图进行了分析，探讨了水辅助生长SnO₂ 纳米带的化学原理和生长机制。结果表明：用水辅助生长法制备的SnO₂纳米带产量高、结构均匀，XRD衍射图与SnO₂的标准图完全一致，纳米带的宽度为70～100 nm，厚度为5～8 nm,长度可达数十微米；SnO₂纳米带光致发光在617 nm和651 nm处有2个强峰，在446 nm处有一个弱峰，这些都是由氧空位引起的；SnO₂纳米带的红外谱图中560.6 cm^-1处的峰属于表面振动模式；水辅助生长SnO₂纳米带的可能机制是VS生长机制。     

骨架结构多孔TiO2薄膜增强染料敏化太阳能电池性能

以空心球状TiO₂为基体、以片状TiO₂为骨架,采用刮刀法制备了染料敏化太阳能电池的多孔TiO₂光阳极薄膜。光电转化效率测试结果表明,当作为骨架支撑材料的片状TiO₂含量为20wt%时,光阳极薄膜组装成太阳能电池的光电转化效率达到最高值4.53%,比商业P₂₅制备的无孔无骨架TiO₂薄膜电池(4.06%)及无骨架结构的多孔TiO₂薄膜电池(4.17%)的性能均有显著提高。当片状TiO₂的最佳含量为20wt%电池薄膜厚度为33μm时,太阳能电池光电转化效率进一步提升为7.06%。光电性能增强的原因是骨架结构有利于快速传输电子并增大染料吸附量。本研究通过设计制备具有骨架结构的多孔TiO₂薄膜为提高染料敏化太阳能电池性能提供了新的思路。     

表面活性剂对染料敏化太阳能电池光电性能的提高

在硝酸/醋酸(HNO₃/HAc)的水溶液中分别加入十二烷基苯磺酸钠(DBS)、十六烷基三甲基溴化铵(CTAB)、吐温20等不同类型的表面活性剂来水解钛酸四正丁酯制得前驱体溶液,通过水热法制备纳晶TiO₂,并组装成染料敏化太阳能电池(DSSC)。通过XRD、SEM和UV-Vis对纳晶TiO₂薄膜进行表征,并对DSSC进行光电流-光电压(I-V)曲线的测试,研究了不同类型的表面活性剂和不同浓度的CTAB对DSSC光电性能的影响。结果表明：加入阳离子表面活性剂CTAB时提高了DSSC的光电性能,而加入阴离子表面活性剂DBS和非离子表面活性剂吐温20时,DSSC的光电性能反而降低。随着CTAB浓度的增加,电池的光电性能先提高后下降,当c_CTAB=0.08 mol·L^-1时,DSSC的光电转化效率最高为5.76%,比不添加表面活性剂制备的纳晶TiO₂所组装的DSSC的光电转化效率提高了约18%。     

骨架结构多孔TiO2薄膜增强染料敏化太阳能电池性能

以空心球状TiO₂为基体、以片状TiO₂为骨架,采用刮刀法制备了染料敏化太阳能电池的多孔TiO₂光阳极薄膜。光电转化效率测试结果表明,当作为骨架支撑材料的片状TiO₂含量为20wt%时,光阳极薄膜组装成太阳能电池的光电转化效率达到最高值4.53%,比商业P25制备的无孔无骨架TiO₂薄膜电池(4.06%)及无骨架结构的多孔TiO₂薄膜电池(4.17%)的性能均有显著提高。当片状TiO₂的最佳含量为20wt%电池薄膜厚度为33 μm时,太阳能电池光电转化效率进一步提升为7.06%。光电性能增强的原因是骨架结构有利于快速传输电子并增大染料吸附量。本研究通过设计制备具有骨架结构的多孔TiO₂薄膜为提高染料敏化太阳能电池性能提供了新的思路。     

双层结构CeO2光阳极在染料敏化太阳能电池中的应用

利用水热法合成核壳结构Au@SiO₂@CeO₂纳米微球,制备了一系列双层结构复合光阳极并应用于染料敏化太阳能电池(DSSC)。研究表明：当CeO₂纳米微球和核壳结构Au@SiO₂@CeO₂纳米微球应用于DSSC光阳极散射层时,电池的光电转化效率有了显著提高。相对于纯 TiO₂ (P25)光阳极,P25/CeO₂纳米球光阳极电池的 DSSC 光电性能提高了 15.3%,P25/Au@SiO₂@CeO₂纳米球光阳极电池的光电性能提高了27.9%。DSSC光电性能的提高主要归因于2个方面：一方面,Au纳米粒子的表面等离子体共振效应有效提高了光阳极薄膜的光散射效应。另一方面,CeO₂具有较高的染料负载能力,核壳球形结构具有较高的比表面积,增强了光的散射效应,提高了电子传输能力。     

Bi2S3量子点敏化TiO2纳米阵列结构的制备及光电性能

利用水热法制备一维TiO₂纳米棒阵列,并采用化学浴沉积法(CBD)结合自组装技术在TiO₂纳米棒上敏化Bi₂S₃量子点,形成TiO₂/Bi₂S₃复合纳米棒阵列。系统研究了复合结构的表面形貌、晶体结构、光学及光电性能。结果表明:在修饰有三氨丙基三乙氧基硅烷自组装单分子膜(APTS-SAMs)的TiO₂纳米棒表面形成一层致密的Bi₂S₃量子点敏化层,这一技术的关键是含-NH₂末端的APTS-SAMs可有效促进Bi₂S₃的异相成核作用;Bi₂S₃的沉积时间对复合结构的光吸收及光电响应性能有决定性的影响,薄膜的光电流随着沉积时间呈先增加后减小的趋势,在沉积时间为20min时,光电流密度最大。这是因为随着沉积时间的增加,TiO₂纳米棒表面Bi₂S₃量子点密度增大,光吸收增加;而当沉积时间进一步延长时,Bi₂S₃在TiO₂纳米棒表面的大量负载而形成堆积和团聚,导致表面缺陷增多,光生电子复合几率增大,从而使光电流密度减小。     

Dye-sensitized solar cells based on TiO2-B nanobelt/TiO2 nanoparticle sandwich-type photoelectrodes with controllable nanobelt length

The TiO(2)-B nanobelt (NB)/TiO(2) nanoparticle (NP) sandwich-type structure photoelectrode, with controllable nanobelt length, has been used to fabricate high-efficiency dye-sensitized solar cells (DSSCs), which combine the advantages of the rapid electron transport in TiO(2)-B NBs and the high surface area of TiO(2) NPs. The results indicate that the sandwich-type photoelectrode achieves higher photoelectrical conversion efficiency when compared with the TiO(2) nanoparticulate electrode. Increasing the length of TiO(2)-B NBs has been demonstrated to improve the photoelectric conversion efficiency (η). DSSCs with the longest (10 μm) TiO(2)-B NBs yield the highest η of 7.94%. The interfacial electron transport of DSSCs with different lengths of TiO(2)-B NBs has been quantitatively investigated using the photovoltage transient and the electrochemical impedance spectra, which demonstrates that the DSSCs with longest TiO(2)-B NBs display the highest electron collection efficiency and the fastest interfacial electron transfer.     

Charge transport versus recombination in dye-sensitized solar cells employing nanocrystalline TiO2 and SnO2 films

We report a comparison of charge transport and recombination dynamics in dye-sensitized solar cells (DSSCs) employing nanocrystalline TiO(2) and SnO(2) films and address the impact of these dynamics upon photovoltaic device efficiency. Transient photovoltage studies of electron transport in the metal oxide film are correlated with transient absorption studies of electron recombination with both oxidized sensitizer dyes and the redox couple. For all three processes, the dynamics are observed to be 2-3 orders of magnitude faster for the SnO(2) electrode. The origins of these faster dynamics are addressed by studies correlating the electron recombination dynamics to dye cations with chronoamperometric studies of film electron density. These studies indicate that the faster recombination dynamics for the SnO(2) electrodes result both from a 100-fold higher electron diffusion constant at matched electron densities, consistent with a lower trap density for this metal oxide relative to TiO(2), and from a 300 mV positive shift of the SnO(2) conduction band/trap states density of states relative to TiO(2). The faster recombination to the redox couple results in an increased dark current for DSSCs employing SnO(2) films, limiting the device open-circuit voltage. The faster recombination dynamics to the dye cation result in a significant reduction in the efficiency of regeneration of the dye ground state by the redox couple, as confirmed by transient absorption studies of this reaction, and in a loss of device short-circuit current and fill factor. The importance of this loss pathway was confirmed by nonideal diode equation analyses of device current-voltage data. The addition of MgO blocking layers is shown to be effective at reducing recombination losses to the redox electrolyte but is found to be unable to retard recombination dynamics to the dye cation sufficiently to allow efficient dye regeneration without resulting in concomitant losses of electron injection efficiency. We conclude that such a large acceleration of electron dynamics within the metal oxide films of DSSCs may in general be detrimental to device efficiency due to the limited rate of dye regeneration by the redox couple and discuss the implications of this conclusion for strategies to optimize device performance.     

二氧化硅纳米粒子薄膜的制备及光学性能

以二氧化硅胶体和聚二烯丙基二甲基氯化铵(PDDA)为原料,利用静电自组装技术制备了PDDA/SiO2复合薄膜. TEM图象显示,薄膜中的SiO2纳米粒子为密堆积,薄膜均匀、致密;电子衍射实验结果显示,所组装的薄膜为非晶态膜.载玻片表面组装SiO2纳米粒子薄膜后,透射率随薄膜双层数增加呈现周期变化.薄膜具有增透作用,载玻片双面组装薄膜后在一定波长范围内的透射率可提高5％以上. PDDA/SiO2复合薄膜的光学性质主要由SiO2纳米粒子决定,每一双层的平均物理厚度小于SiO2纳米粒子的粒径,薄膜中存在层间穿插现象,逐层组装的复合薄膜具有单层光学薄膜的特性.     

Sonochemical synthesis of SnO2 nanobelt/CdS nanoparticle core/shell heterostructures

SnO2 nanobelt/CdS nanoparticle core/shell heterostructures are successfully achieved via a simple sonochemical approach; their ethanol-sensing properties are discussed.     

纳米稀土-介质薄膜光电发射光谱和能带结构

用真空蒸发沉积的方法制备了纳米稀土(La、Nd、Sm)粒子 BaO介质薄膜.研究表明薄膜的光电发射光谱响应阈值受纳米稀土粒子形状和大小的影响,球形纳米稀土(Sm)粒子 BaO介质薄膜的光谱响应阈值波长为720 nm,条状纳米稀土(La和Nd)粒子 BaO介质薄膜阈值波长分别为650 nm和660 nm.研究得到纳米稀土粒子 介质薄膜等效界面位垒高度在1.7～2.0 eV之间.由于纳米稀土粒子与BaO介质各自逸出功不同,当构成薄膜后使得纳米粒子周围的空间电荷分布发生变化,纳米粒子周围的能带发生弯曲.     

基于铝离子掺杂二氧化钛薄膜的染料敏化太阳能电池的光电性能

采用水热法制备出Al3+掺杂二氧化钛薄膜,通过玻璃棒涂于导电玻璃上,在450°C的温度下烧结并将其用N3染料敏化制成染料敏化太阳能电池(DSSCs).通过X射线光电子能谱(XPS)、X射线衍射(XRD)、扫描电镜(SEM)及DSSCs测试系统对其进行了测试表征,研究了Al3+掺杂对TiO2晶型及染料敏化太阳能电池的光电性能影响.XPS数据显示Al3+成功掺杂到了TiO2晶格内,由于Al3+的存在,对半导体内电子和空穴的捕获及阻止电子/空穴对的复合发挥重要作用.莫特-肖特基曲线显示掺杂Al3+后二氧化钛平带电位发生正移,并导致电子从染料注入到TiO2的驱动力提高.DSSCs系统测试结果表明,Al3+掺杂的TiO2薄膜光电效率达到6.48%,相对于无掺杂的纯二氧化钛薄膜光电效率(5.58%),其光电效率提高了16.1%,短路光电流密度从16.5mA·cm-2提高到18.2mA·cm-2.     

Enhanced photovoltaic characterization and charge transport of TIO2 nanoparticles/nanotubes composite photoanode based on indigo carmine dye-sensitized solar cells

Dye-sensitized solar cells (DSSCs) have established themselves as an alternative to conventional solar cells owing to their remarkably high power conversion efficiency, longtime stability and low-cost production. DSSCs composed of a dyed oxide semiconductor photoanode, a redox electrolyte and a counter electrode. In these devices, conversion efficiency is achieved by ultra-fast injection of an electron from a photo excited dye into the conduction band of metal oxide followed by subsequent dye regeneration and holes transportation to the counter electrode. The energy conversion efficiency of DSSC is to be dependent on the morphology and structure of the dye adsorbed metal oxide photoanode. Worldwide considerable efforts of DSSCs have been invested in morphology control of photoanode film, synthesis of stable optical sensitizers and improved ionic conductivity electrolytes. In the present investigation, a new composite nano structured photoanodes were prepared using TiO₂ nano tubes (TNTs) with TiO₂ nano particles (TNPs). TNPs were synthesized by sol–gel method and TNTs were prepared through an alkali hydrothermal transformation. Working photoanodes were prepared using five pastes of TNTs concentrations of 0, 10, 50, 90, and 100 % with TNPs. The DSSCs were fabricated using Indigo carmine dye as photo sensitizer and PMII (1-propyl-3-methylimmidazolium iodide) ionic liquid as electrolyte. The counter electrode was prepared using Copper sulfide. The structure and morphology of TNPs and TNTs were characterized by X-ray diffraction and electron microscopes (TEM and SEM). The photocurrent efficiency is measured using a solar simulator (100 mW/cm²). The prepared composite TNTs/TNPs photoanode could significantly improve the efficiency of dye-sensitized solar cells owing to its synergic effects, i.e. effective dye adsorption mainly originated from TiO₂ nanoparticles and rapid electron transport in one-dimensional TiO₂ nanotubes. The results of the present investigation suggested that the DSSC based on 10 % TNTs/TNPs showed better photovoltaic performance than cell made pure TiO₂ nanoparticles. The highest energy-conversion efficiency of 2.80 % is achieved by composite TNTs (10 %)/TNPs film, which is 68 % higher than that pure TNPs film and far larger than that formed by bare TNTs film (94 %). The charge transport and charge recombination behaviors of DSSCs were investigated by electrochemical impedance spectra and the results showed that composite TNTs/TNPs film-based cell possessed the lowest transfer resistances and the longest electron lifetime. Hence, it could be concluded that the composite TNTs/TNPs photoanodes facilitate the charge transport and enhancing the efficiencies of DSSCs.     

Self‐Assembly and Surface Photovoltage Response of ZnS Nanoparticulate Films Sensitized by Tetrasulfonated Copper Phthalocyanine

Composite films of ZnS nanoparticle‐polyelectrolyte were fabricated by the layer‐by‐layer self‐assembly technique. The optical properties and structure of the films were characterized by UV‐vis absorption spectra and AFM. The films sensitized by tetrasulfonated copper phthalocyanine (CuTsPc) show wide photovoltaic response range. The surface photovoltages corresponding to the ZnS nanoparticle interband transition and CuTsPc Q band transition in the sensitized film are approximately three to four times stronger than those in the ZnS nanoparticle‐polyelectrolyte film and CuTsPc film, respectively, which is attributed to the electron transition from the excited state of CuTsPc to the conduction band of ZnS nanoparticles.     

Enhancing Electron Collection Efficiency and Effective Diffusion Length in Dye‐Sensitized Solar Cells

Intensity‐modulated photocurrent spectroscopy and intensity‐modulated photovoltage spectroscopy are employed to measure the dynamics of electron transport and recombination in the ZnO nanowire (NW) array‐ZnO/layered basic zinc acetate (LBZA) nanoparticle (NP) composite dye‐sensitized solar cells (DSSCs). The roles of the vertical ZnO NWs and insulating LBZA in the electron collection and transport in DSSCs are investigated by comparing the results to those in the TiO₂–NP, horizontal TiO₂–NW and vertical ZnO–NW‐array DSSCs. The electron transport rate and electron lifetime in the ZnO NW/NP composite DSSC are superior to those in the conventional TiO₂–NP cell due to the existence of the vertical ZnO NWs and insulating LBZA. It indicates that the ZnO NW/NP composite anode is able to sustain efficient electron collection over much greater thickness than the TiO₂–NP cell does. Consequently, a larger effective electron diffusion length is available in the ZnO composite DSSC.     

有机染料D-SS和D-ST用于染料敏化太阳能电池光敏剂的比较

为了揭示D-SS和D-ST分子敏化的染料敏化太阳能电池(DSSCs)的物理机制,采用密度泛函理论(DFT)、含时密度泛函理论(TDDFT)和自然键轨道(NBO)分析,模拟计算染料D-SS和D-ST分子的结构、紫外-可见吸收光谱和能级结构.D-SS的紫外-可见吸收光谱相比于D-ST的有明显的红移,而且D-SS分子的摩尔吸光系数也高于D-ST分子的.D-SS分子本应该比D-ST分子拥有更高的俘获太阳辐射光子的能力,但由于D-SS分子的最高占据分子轨道(HOMO)能级位置比氧化还原电解质(|-/|-3)的氧化还原能级高,处于光激发态的D-SS分子向TiO2电极注入电子而被氧化后,不能顺利地从电解质中得到电子而还原,使得D-SS分子俘获光子的能力不能充分发挥,从而严重地降低了由其敏化的DSSCs的光电性能和光电能量转换效率.揭示了D-SS敏化的DSSCs的光电性能,特别是光电能量转换效率比D-ST敏化的DSSCs的低的原因.染料敏化剂分子的HOMO能级的位置对于DSSCs来说也是很重要的,用于DSSCs的有机敏化剂分子的HOMO能级的位置必须低于氧化还原电解质的氧化还原能级.