染料敏化太阳能电池中染料分子共轭π桥的扩展

以染料分子D5为原型, 采用不同类型和数量的共轭桥单元来设计D-π-A 型有机分子. 采用密度泛函理论(DFT)和含时密度泛函理论(TDDFT)来模拟计算分子的形貌、分子轨道能级以及紫外-可见光谱, 为染料敏化太阳能电池(DSSCs)的敏化分子寻找适合的共轭桥. 采用“次甲基链”、“呋喃环”或“噻吩环”、“次甲基链和呋喃环”或“次甲基链和噻吩环”作为共轭桥单元, 使得分子的吸收光谱依次红移. 随着共轭桥单元的增加, 分子的吸收光谱有剧烈的红移, 但随着共轭桥单元数量的进一步增加, 分子吸收光谱的红移现象减弱. 分子的最低未占据分子轨道(LUMO)能级逐渐降低, 而最高占据分子轨道(HOMO)能级逐渐升高. 采用3个“次甲基链和呋喃环”或者“次甲基链和噻吩环”作为共轭桥时, HOMO能级已经高于氧化还原电解质的能级, 而在极性溶液中, 由2个“次甲基链和噻吩环”单元作为有机分子的共轭桥时, 分子的HOMO能级已经高于氧化还原电解质的能级了. 采用“次甲基链和呋喃环”或“次甲基链和噻吩环”单元作为有机分子的共轭桥时, 吸收光谱有明显的红移,但对于DSSCs的敏化分子, 这样的共轭桥单元只能有1-2个, 不宜过多.     

四硫富瓦烯作为染料敏化太阳能电池有机染料电子给体的理论研究(英文)

为了研究四硫富瓦烯(TTF)基团对有机染料敏化剂光电性能的影响,以咔唑染料Dye 1为原型,引入TTF基团作为电子给体,设计了咔唑染料Dye 2.采用密度泛函理论(DFT)和含时密度泛函理论(TD-DFT)分别计算模拟了纯染料分子和吸附团簇(TiO2)9后的形貌、分子轨道能级以及紫外-可见吸收光谱,采用周期性密度泛函理论计算模拟染料分子在二氧化钛(101)面吸附的表面形貌.结果发现:在有机染料中引入TTF基团有助于有机染料敏化剂在二氧化钛表面的抗团聚作用和分子内的电荷转移;最为重要的是,TTF基团的强给电子能力极大地增强了有机染料敏化剂的光捕获能力.所有的计算结果表明,TTF基团是一种非常有潜力改善染料敏化剂光电性能的给电子基团.     

二氢吲哚类染料用于染料敏化太阳能电池光敏剂的比较

采用密度泛函理论(DFT)和含时密度泛函理论(TD-DFT)对四种二氢吲哚染料进行研究, 从中筛选出相对优秀的染料敏化太阳能电池光敏剂. 对前线分子轨道的计算表明, 二氢吲哚染料的前线分子轨道结构非常有利于染料激发态向TiO2电极的电子注入. 对真空中的紫外和可见光吸收光谱的计算表明, 二氢吲哚染料的吸收光谱与太阳辐射光谱匹配较好. 对染料分子的能级计算表明, 二氢吲哚染料的能级结构比较适合于I-/I-3作电解液的TiO2纳米晶太阳能电池的光敏剂. 二氢吲哚染料最低未占据分子轨道(LUMO) 能级均比TiO2晶体导带边能级高, 能够保证激发态染料分子高效地向TiO2电极转移电子. 二氢吲哚染料最高占据分子轨道(HOMO)的能级比I-/I-3能级低, 保证了失去电子的染料分子能够顺利地从电解液中得到电子. 与实验数据比较, 得出在提高染料敏化太阳能电池转换效率方面, 对染料的关键要求是LUMO能级的位置. 染料分子的稳定性是染料敏化太阳能电池使用寿命的关键因素. 通过对化学键键长的比较表明, 二氢吲哚染料的分子稳定性基本相同. 对计算结果的分析表明, 二氢吲哚染料1(ID1)的LUMO能级最高, 分子稳定性最好, 在酒精溶液中的吸收光谱与太阳辐射光谱匹配很好, 在同类染料中是较好的染料敏化太阳能电池光敏剂.     

四硫富瓦烯作为染料敏化太阳能电池有机染料电子给体的理论研究

为了研究四硫富瓦烯(TTF)基团对有机染料敏化剂光电性能的影响,以咔唑染料Dye 1 为原型,引入TTF基团作为电子给体,设计了咔唑染料Dye 2. 采用密度泛函理论(DFT)和含时密度泛函理论(TD-DFT)分别计算模拟了纯染料分子和吸附团簇(TiO₂)₉后的形貌、分子轨道能级以及紫外-可见吸收光谱,采用周期性密度泛函理论计算模拟染料分子在二氧化钛(101)面吸附的表面形貌. 结果发现：在有机染料中引入TTF基团有助于有机染料敏化剂在二氧化钛表面的抗团聚作用和分子内的电荷转移;最为重要的是,TTF 基团的强给电子能力极大地增强了有机染料敏化剂的光捕获能力. 所有的计算结果表明,TTF基团是一种非常有潜力改善染料敏化剂光电性能的给电子基团.     

8-羟基喹啉铁配合物对锐钛矿型TiO2（101）表面的敏化机理

用密度泛函理论和DMol3程序包对锐钛矿型TiO2(101)表面复合三(8-羟基喹啉-5-羧酸)铁的敏化机理进行了研究.计算结果表明,该染料敏化剂经式结构的HOMO(最高占据分子轨道)-LUMO(最低未占据分子轨道)能隙非常小,很容易受到激发;TiO2纳米晶吸附染料后,HOMO、LUMO和费米能级都升高,导致吸附染料后开路电压VOC升高.并进一步探讨了(8-羟基喹啉-5-羧酸)铁在TiO2(101)表面复合过程及作用机理.     

8-羟基喹啉铁配合物对锐钛矿型TiO2(101)表面的敏化机理

用密度泛函理论和DMol3程序包对锐钛矿型TiO2(101)表面复合三(8-羟基喹啉-5-羧酸)铁的敏化机理进行了研究. 计算结果表明, 该染料敏化剂经式结构的HOMO(最高占据分子轨道)-LUMO(最低未占据分子轨道)能隙非常小, 很容易受到激发; TiO2纳米晶吸附染料后, HOMO、LUMO 和费米能级都升高, 导致吸附染料后开路电压VOC升高. 并进一步探讨了三(8-羟基喹啉-5-羧酸)铁在TiO2(101)表面复合过程及作用机理.     

π桥中不同吸电子基团对三苯胺-氰基丙烯酸类染料敏化太阳能电池性能影响的理论研究

采用密度泛函理论和含时密度泛函理论计算了染料的紫外-可见吸收光谱、电子注入驱动力、半导体导带能级移动量以及染料与碘的相互作用能等一系列评价电池性能的理论参数,以解释在π桥上引入不同吸电子基团导致三苯胺-氰基丙烯酸基染料敏化太阳能电池光电转换效率降低的原因.结果表明,在染料π桥上引入吸电子基团虽可以在一定程度上改善吸收光谱,但同时也引入了额外的与电解质中碘相互作用的位点,加快了与电解质之间的复合速率,影响了电子注入驱动力,最终导致电池光电转换效率降低.因此,在设计高效光敏染料时除了考虑吸收光谱外,也应考虑染料与电解质之间的复合以及电子注入驱动力这2个影响电池性能的关键因素.     

用于监控过氧化氮的近红外荧光探针的光物理性质及PET机理

含有机硒的七甲川菁染料是基于光诱导电子转移(PET)的近红外(IR)荧光探针, 能在生理条件下高灵敏、高选择性地监控过氧化氮. 本文应用含时密度泛函理论(TD-DFT)计算方法研究其光物理性质和PET机理.结果表明, 在激发态, 荧光母体发生最高占有分子轨道(HOMO)到最低非占有分子轨道(LUMO)的电子跃迁, 识别基团上的HOMO轨道能级提高到荧光母体的单电子占据的HOMO轨道能级之上, 并向其转移一个电子, 使激发态电子回落过程受阻而导致荧光部分淬灭. 硒被氧化后, 识别基团上的HOMO轨道能级降低, PET过程被阻断, 荧光发射恢复. 研究进一步证明, PET效应来自于识别基团上苯胺N原子的p电子, 它的电子转移能力受到其对位苯硒基的氧化-还原状态的影响, 产生了荧光信号的“开-关”作用.     

有机染料敏化剂JK16和JK17的几何结构、电子结构及相关性质

运用密度泛函理论中的杂化泛函B3LYP研究了高效太阳能电池新型染料敏化剂JK16和JK17的几何结构、电子结构、极化率和超极化率, 并用含时密度泛函理论(TDDFT)研究了电子吸收谱. 基于含时密度泛函理论计算结果和实验结果的定性符合, 指认了在可见和近紫外区的吸收属于π→π*跃迁. 计算结果还表明JK16和JK17激发能最低的三个跃迁都与光诱导电荷转移过程有关, 而且二-二甲基芴氨基苯并噻吩基团对光电转换过程的敏化起主要作用, 发生于染料敏化剂JK16、JK17和TiO2界面之间的电荷转移是由染料分子激发态向半导体导带的电子注入过程. 此外, 通过对JK16和JK17的比较, 分析了亚乙烯基对几何结构、电子结构和谱学特性的影响.     

香豆素型染料敏化剂的合成及光电性能研究

选择带有供电子基团的香豆素作为给体,噻吩基作为桥键,氰乙酸为受体,合成了两种新的具有"D-π-A"结构的香豆素型染料敏化剂,对其光谱性能、电化学性能以及光电转换性能进行了测试.结果表明,两者分子轨道能级与TiO2电极的导带以及电解质I2/I-的氧化还原电位相匹配,保证了电池电流循环的顺利产生.与甲氧基取代的染料敏化剂2-氰基-3-[5-(7-甲氧基-2-羰基-2H-苯并吡喃-3-基)噻吩-2-基]丙烯酸(IIIb)相比,香豆素环7位上二乙氨基取代的染料敏化剂2-氰基-3-[5-(7-二乙胺基-2-羰基-2H-苯并吡喃-3-基)噻吩-2-基]丙烯酸(IIIa)分子内电荷转移吸收较强,紫外吸收光谱红移.IIIa组装得到的染料敏化太阳能电池暗电流降低,具有较高的单色光转化效率IPCE(incident photo-to-currentconversion efficient)和短路电流Jsc,从而具有较高的光电转换效率(Jsc=8.68 mA/cm2,Voc=574 mV,η=3.52%).     

Optical and Electrical Properties of Triphenylamine Derivatives for Dye-sensitized Solar Cells and Designing of Novel Molecule

With density functional theory(DFT) method, the optimization of molecular configurations and the calculation of frontier molecular orbitals were achieved for triphenylamine(TPA)-based dye-sensitized solar cell materials at the B3LYP/6-31G(d, p) level. Time-dependent density functional theory(TD-DFT) was applied to calculating the probability of the transition from the ground state to the excited state. And UV-Vis absorption spectra were derived with Franck-Condon approximation. The conjugation length, substitution groups and spatial effects show a slight influence on the dihedral angle of the TPA group. The increase of conjugation length may cause a smaller energy gap as well as a higher highest occupied molecular orbital(HOMO) and a lower lowest unoccupied molecular orbital (LUMO). The introduction of methoxyl group and TPA group could lower the energy gap while the HOMO and LUMO were elevated in energy.     

Charge separation versus recombination in dye-sensitized nanocrystalline solar cells: the minimization of kinetic redundancy

In this paper we focus upon the electron injection dynamics in complete dye-sensitized nanocrystalline metal oxide solar cells (DSSCs). Electron injection dynamics are studied by transient absorption and emission studies of DSSCs and correlated with device photovoltaic performance and charge recombination dynamics. We find that the electron injection dynamics are dependent upon the composition of the redox electrolyte employed in the device. In a device with an electrolyte composition yielding optimum photovoltaic device efficiency, electron injection kinetics exhibit a half time of 150 ps. This half time is 20 times slower than that for control dye-sensitized films covered in inert organic liquids. This retardation is shown to result from the influence of the electrolyte upon the conduction band energetics of the TiO2 electrode. We conclude that optimum DSSC device performance is obtained when the charge separation kinetics are just fast enough to compete successfully with the dye excited-state decay. These conditions allow a high injection yield while minimizing interfacial charge recombination losses, thereby minimizing "kinetic redundancy" in the device. We show furthermore that the nonexponential nature of the injection dynamics can be simulated by a simple inhomogeneous disorder model and discuss the relevance of our findings to the optimization of both dye-sensitized and polymer based photovoltaic devices.     

Photovoltaic performance of dye-sensitized solar cells assembled by in-situ chemical cross-linking

Quasi-solid state dye-sensitized solar cells (DSSCs) were assembled by in-situ chemical cross-linking of a gel electrolyte precursor containing liquid electrolyte. The DSSCs assembled with this cross-linked gel polymer electrolyte showed higher open circuit voltage and lower short-circuit photocurrent density than those of DSSCs with liquid electrolyte. Addition of SiO₂ nanoparticles into the cross-linked gel polymer electrolyte significantly improved the photovoltaic performance and long-term stability of the DSSCs. The optimized quasi-solid state DSSC showed high conversion efficiency, 6.2% at 100 mW cm^?2 with good durability.     

Exploration on Charge Transfer and Absorption Spectra of Spiro[fluorene-9,90-xanthene]-based Polyoxometalate Hybrids Toward High Performance Dye-sensitized Solar Cell

Based on spiro[fluorene-9,90-xanthene](SFX, dye 1), the Lindqvist-type polyoxometalate(POM) functionalized with SFX and its derivatives(dyes 2-4) used in dye-sensitized solar cells(DSSCs) were designed and investigated with the density functional theory(DFT) and time-dependent DFT(TD-DFT) calculations. The results indicate that Lindqvist-type POM is the main contribution to the lowest unoccupied molecular orbital(LUMO) and affects the LUMO energies of dyes 2-4. The maximum absorptions of the designed dyes containing POM(dyes 2-4) are red shifted comparing with that of dye 1. The introduction of electron-donating group onto SFX segment is helpful to red shift the absorption spectra. The major factors affecting the performance of DSSCs, including light harvesting and electron injection were evaluated. Considering the absorption spectra and photovoltaic parameters, dyes 3 and 4 are promising high performance dye sensitizers in n-type DSSCs.     

Photovoltaic Performance of Triphenylamine Dyes-sensitized Solar Cells Employing Cobalt Redox Shuttle and Influence of π-conjugated Spacers

Developing photosensitizers suitable for the cobalt electrolyte and understanding the structure-property relationship of organic dyes is warranted for the dye-sensitized solar cells (DSSCs). The DSSCs incorporating tris(1,10-phenanthroline)cobalt(II/III)-based redox elec-trolyte and four synthesized organic dyes as photosensitizers are described. The photovoltaic performance of these dyes-sensitized solar cells employing the cobalt redox shuttle and the influences of the π-conjugated spacers of organic dyes upon the photovoltage and photocur-rent of mesoscopic titania solar cells are investigated. It is found that organic dyes with thiophene derivates as linkers are suitable for DSSCs employing cobalt electrolytes. DSSCs sensitized with the as-synthesized dyes in combination with the cobalt redox shuttle yield an overall power conversion efficiency of 6.1% under 100 mW/cm² AM1.5 G illumination.     

Efficient eosin y dye-sensitized solar cell containing Br-/Br3- electrolyte

We found that Br-/Br3- is more suitable than an I-/I3- couple in dye-sensitized solar cells in terms of higher open-circuit photovoltage (Voc) production and higher overall energy conversion efficiency (eta) if the dye sensitizer has a more positive potential than that of Br-/Br3-. Under simulated AM1.5 one sun, an eosin Y dye-sensitized solar cell containing 0.4 M LiBr + 0.04 M Br2 electrolyte in acetonitrile yielded a short-circuit photocurrent (Jsc) of 4.63 mA cm(-2), Voc of 0.813 V, and fill factor (FF) of 0.693, corresponding to 2.61% of eta. Under the same conditions except for the electrolyte 0.4 M LiI + 0.04 M I2 in acetonitrile instead, the device produced 1.67% of eta (Jsc = 5.15 mA cm(-2), Voc = 0.451 V, FF = 0.721). Replacement of I-/I3- with Br-/Br3- in eosin Y dye-sensitized solar cells yielded a significant increase in Voc offset by slight decreases in Jsc and FF, leading to an increase in eta by 56%. The significant gain in Voc was attributed to the enlarged energy level difference between the redox potential of the electrolyte and the Fermi level of TiO2 and the suppressed charge recombination as well. The rate for charge recombination between bromine and the injected electrons was determined to be first order in bromine.     

A Combined Experimental and Computational Study of Chrysanthemin as a Pigment for Dye-Sensitized Solar Cells

The theoretical study of chrysanthemin (cyanidin 3-glucoside) as a pigment for TiO₂-based dye-sensitized solar cells (DSSCs) was performed with the GAUSSSIAN 09 simulation. The electronic spectra of neutral and anionic chrysanthemin molecules were calculated by density functional theory with B3LYP functional and DGDZVP basis set. A better energy level alignment was found for partially deprotonated molecules of chrysanthemin, with the excited photoelectron having enough energy in order to be transferred to the conduction band of TiO₂ semiconductor in DSSCs. In addition, we used the raw aqueous extracts of roselle (Hibiscus sabdariffa) calyces as the source of chrysanthemin and the extracts with various pH values were tested in DSSCs. The extracts and photosensitized semiconductor layers were characterized by UV-Vis spectroscopy, and DSSCs based on raw extracts were characterized by current density-voltage measurements.     

Synthesis and photovoltaic properties of organic sensitizers incorporating a thieno[3,4-c]pyrrole-4,6-dione moiety

Novel organic sensitizers containing a thieno[3,4-c]pyrrole-4,6-dione (TPD) moiety with triphenylamine or julolidine as the electron donor have been designed and synthesized for quasi-solid-state dye-sensitized solar cells (DSSCs). For comparison, two organic dyes based on a terthiophene spacer have also been synthesized. The absorption, electrochemical and photovoltaic properties of all sensitizers have been systematically investigated. We found that the incorporation of TPD is highly beneficial to broaden the absorption spectra of the organic sensitizers and prevent the intermolecular interaction. Therefore, the charge recombination possibility is reduced, which is revealed by the controlled intensity modulated photovoltage spectroscopy. A quasi-solid-state DSSC based on sensitizer FNE38 with TPD and triphenylamine moieties demonstrates a solar energy conversion efficiency of 4.71% under standard AM 1.5G sunlight without the use of coadsorbant agents.