Lead determination in whole blood by laser ablation coupled with inductively coupled plasma mass spectrometry

This work describes a simple procedure for blood lead level determination. The proposed method requires little sample pretreatment and subsequent direct analysis of a dried blood spot on a filter membrane using laser ablation coupled with inductively coupled plasma mass spectrometry (LA-ICP-MS). In general, LA-ICP-MS studies are somewhat limited by the lack of matrix-matched standards for calibration purposes. Here we describe aqueous standard calibration and matrix-matched calibration methods. This method was validated by analysis of the reference materials. With the matrix-matched calibration method, the recovery ranged from 97.8% to 112.8%, while the aqueous standard calibration method ranged 90.4% to 122.4%. The lower detection limit was estimated as 0.1 ng mL⁻¹. The determination precision, expressed as the relative standard deviation (RSD), was not worse than 10% for all results. A sample throughput of approximately 5 min per sample made it possible to rapidly screen a large number of samples.     

Matrix effects in inductively coupled plasma mass spectrometry: a review

Fundamental research on non-spectroscopic interferences, also known as matrix effects, in inductively coupled plasma (ICP) mass spectrometry with sample introduction using nebulization is critically and exclusively examined in this review, starting with fundamental processes that may be a source of matrix effects during sample introduction, ion generation in the ICP, ion extraction through the interface, and ion transport through the ion optics to the detector. Various methods for attenuating matrix effects are then reviewed and illustrated with some examples. Instead of exhaustively reviewing the literature, representative references are used to comprehensively describe the main issues, several of which are also common to ICP optical emission spectrometry.     

Applications of inductively coupled plasma mass spectrometry and laser ablation inductively coupled plasma mass spectrometry in materials science

Inductively coupled plasma mass spectrometry (ICP-MS) and laser ablation ICP-MS (LA-ICP-MS) have been applied as the most important inorganic mass spectrometric techniques having multielemental capability for the characterization of solid samples in materials science. ICP-MS is used for the sensitive determination of trace and ultratrace elements in digested solutions of solid samples or of process chemicals (ultrapure water, acids and organic solutions) for the semiconductor industry with detection limits down to sub-picogram per liter levels. Whereas ICP-MS on solid samples (e.g. high-purity ceramics) sometimes requires time-consuming sample preparation for its application in materials science, and the risk of contamination is a serious drawback, a fast, direct determination of trace elements in solid materials without any sample preparation by LA-ICP-MS is possible. The detection limits for the direct analysis of solid samples by LA-ICP-MS have been determined for many elements down to the nanogram per gram range. A deterioration of detection limits was observed for elements where interferences with polyatomic ions occur. The inherent interference problem can often be solved by applying a double-focusing sector field mass spectrometer at higher mass resolution or by collision-induced reactions of polyatomic ions with a collision gas using an ICP-MS fitted with collision cell. The main problem of LA-ICP-MS is quantification if no suitable standard reference materials with a similar matrix composition are available. The calibration problem in LA-ICP-MS can be solved using on-line solution-based calibration, and different procedures, such as external calibration and standard addition, have been discussed with respect to their application in materials science. The application of isotope dilution in solution-based calibration for trace metal determination in small amounts of noble metals has been developed as a new calibration strategy. This review discusses new analytical developments and possible applications of ICP-MS and LA-ICP-MS for the quantitative determination of trace elements and in surface analysis for materials science.     

Element-tagged immunoassay with inductively coupled plasma mass spectrometry for multianalyte detection

The multianalyte immunoassay approach is currently attracting increasing attention due to its high sample throughput, short assay time, low sample consumption and reduced overall cost per assay. This paper reviews progress in the field of multianalyte immunoassays using inductively coupled plasma mass spectrometry, as well as applications of this approach in different fields. Examples related to the combination of protein microarray technology with the multitag approach of the immunoassay ICP-MS method and to the use of ICP-MS in the field of imaging are described. A novel strategy that involves tagging antibodies for ICP-MS detection in sensitive multitag bioassays is also presented. Finally, the outlook for this promising technique is discussed.     

Capillary electrophoresis inductively coupled plasma mass spectrometry

Chemical speciation (extraction of elemental information and identification of molecular environment for an analyte in a complex sample) has been a long sought after goal for analytical chemists. Recently, because of successful developments in more sensitive element-specific detectors and gentle separation schemes, which preserve the true chemical information in a real sample, routine speciation experiments are becoming a common occurrence in the scientific literature. For many reasons, the combination of capillary electrophoresis (for separation of different chemical species) with inductively coupled plasma mass spectrometry (for element and isotope specific detection) has emerged as the method of choice for these analyses. In this article the basic principles of capillary electrophoresis inductively coupled plasma mass spectrometry are discussed. Design consideration for instrument interface, anticipated difficulties with speciation experiments and applications for specific matrices and analytes are also presented in this article.     

Design analysis of a laser ablation cell for inductively coupled plasma mass spectrometry by numerical simulation

A laser ablation setup including outer chamber, sample tube, sample holder and transport tubing was modelled and optimized using advanced computational fluid dynamics techniques. The different components of the setup were coupled and the whole device was modelled at once. The mass transport efficiency and transit times of near infrared femtosecond (fs) laser generated brass aerosols in pure argon and helium–argon mixtures were calculated at experimentally optimized conditions and a transient signal was constructed. The use of helium or argon did not influence the mass transport efficiency, but the signal structure changed. The signal fine structure was retrieved and experimentally validated. Bimodal peak structures were observed that seemed to originate from turbulent effects in the tubing connecting a Y-connector and the injector.     

Determination of minor elements in steelmaking flue dusts using laser ablation inductively coupled plasma mass spectrometry

Element determination in solid waste products from the steel industry usually involves the time-consuming step of preparing a solution of the solid. Laser ablation (LA) inductively coupled plasma mass spectrometry (ICP-MS) has been applied to the analysis of Cr, Ni, Cu, As, Cd and Sn, elements of importance from the point of view of their impact on the environment, in electric arc furnace flue dust (EAFD). A simple method of sample preparation as pressed pellets using a mixture of cellulose and paraffin as binder material was applied. Calibration standards were prepared spiking multielement solution standards to a 1:1 ZnO + Fe₂O₃ synthetic matrix. The wet powder was dried and mechanically homogenised. Quantitative analysis were based on external calibration using a set of matrix matched calibration standards with Rh as a internal standard. Results obtained using only one-point for calibration without matrix matched, needing less time for standardization and data processing, are also presented. Data are calculated for flue dust reference materials: CRM 876-1 (EAFD), AG-6203 (EAFD), AG-6201 (cupola dust) and AG-SX3705 (coke ashes), and for two representative electrical arc furnace flue dusts samples from Spanish steelmaking companies: MS-1 and MS-2. For the reference materials, an acceptable agreement with certificate values was achieved, and the results for the MS samples matched with those obtained from conventional nebulization solutions (CN). The analytical precision was found to be better than 7% R.S.D. both within a single pellet and between several pellets of the same sample for all the elements.     

Multi-element analysis of compost by laser ablation-inductively coupled plasma mass spectrometry

Laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) has been applied to multi-element determination in compost samples. Since compost is a heterogeneous mixture of organic and inorganic materials, the influence of sample heterogeneity on the accuracy and precision of analysis was investigated. Several parameters related to the following were studied: laser (energy, laser-beam diameter, preablation. rastering speed, carrier-gas flow rate), sample preparation (use of compacted pellets, grinding time, particle size, sample amount, length of hydraulic press treatment, position of line scan), and the ICP-MS system (quantitative versus semiquantitative analysis, matrix-matched standards and liquid standards calibration). The main causes of imprecision in sample preparation were determined to be particle size and grinding time. The effect of sample heterogeneity on precision was also evaluated by using different test samples (pellets). For Ni, Zn and Pb, the greatest contribution to the total relative standard deviation (R.S.D.) was related to analyte determination. For Mn and Cu, sample heterogeneity and analyte determination contributed equally to the total R.S.D., whereas for Cr, Co, Cd and Hg sample heterogeneity accounted for most of the total R.S.D. A comparison of semiquantitative and quantitative analysis modes showed that better precision and very good agreement with certified reference material was obtained with the latter, but semiquantitative analysis could be a practical alternative. Although accuracy of results was improved with matrix-matched standards calibration the use of standard addition calibration with aqueous standards could be another possibility.     

Using dried-droplet laser ablation inductively coupled plasma mass spectrometry to quantify multiple elements in whole blood

This paper describes a simple procedure for the direct analysis and determination of multiple elements in dried blood samples on a filter membrane using laser ablation coupled with inductively coupled plasma mass spectrometry (LA-ICP-MS). With this technique, we simultaneously quantified 13 elements in whole blood: Be, Mn, Co, Ni, Tl, Bi, Sb, Pb, Cu, Zn, Ba, Mg, and Cd. The measured accuracies was in agreement with the Seronorm CRM certified values, except for Mn, Zn, Ba and Cd, which presented absolute differences higher than the expanded uncertainty for these elements. The within-run precision was less than 5.7% (relative standard deviation, RSD), except for the analyses of Be, and Mn (8.6% and 11.1%, respectively). The reproducibility (between-run precision) was calculated in terms of the RSD obtained for 12 analyses (i.e., four replicates of each sample in three analytical runs). Apart from Be, Mn, and Zn, the reproducibilities of all the elements listed above ranged between 4.0% and 8.5%. In contrast, for Cd, the concentration obtained was significantly different from the certified value; analyses of this element exhibited low reproducibility. Applying the matrix-matched calibration method, the accuracy for Cd measured was in agreement with both SRM966 and BCR 635; thus, matrix-matched calibration is a practical means of overcoming matrix-enhancement effects for the quantification of Cd. Sample throughput (ca. 5 min per sample) made it possible to rapidly screen a larger number of samples relative to other techniques that require time-consuming sample preparation steps (e.g., removal of a portion of the solid sample or digestion).     

硝酸-过氧化氢敞口消解/ICP-MS测定植物样品砷含量

选取了玉米秸秆与籽粒、小麦秸秆与籽粒、烟草等5种不同的植物样品,加入硝酸-过氧化氢,进行敞口消解,消解液中As(⁷⁵As)采用电感耦合等离子体质谱仪He碰撞模式测定,以⁷²Ge为内标元素。结果表明：2个国家生物成分分析标准物质GBW10011(GSB-2,小麦)和GBW10020(GSB-11,柑橘叶)砷的测定值在标准确认值范围内;在植物样品中加入砷标准溶液,加标回收率在87%~104%之间;方法检出限为0.0055 μg/g,灵敏度较高;对4个植物样品分别重复测定5次,相对标准偏差均小于10%。本文结论认为电感耦合等离子体质谱仪He碰撞模式可以用于测定硝酸-过氧化氢敞口消解植物样品中砷含量,该方法测定结果准确可靠,重现性好,灵敏度高。     

Application of laser ablation inductively coupled plasma mass spectrometry for the isotopic analysis of single uranium particles

The paper describes the application of laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) for the isotopic analysis of individual uranium-oxide particles. The procedure developed is suitable for the accurate measurement of ²³⁴U, ²³⁵U, ²³⁶U and ²³⁸U isotopes in single actinide particles with lateral dimensions down to 10 μm. The ²³⁵U/²³⁸U isotope ratios can be obtained with a precision of a few percent relative standard deviation using a single collector ICP-MS instrument. The precision could be improved by the use of slow ablation and by taking several LA-ICP-MS replicate spectra on the same particle investigated. For the minor isotopes use of higher mass resolution (R = 4000) was necessary in some cases to avoid spectral interferences. The technique developed offers a rapid and accurate possibility for the isotopic composition determination of uranium-containing individual particles in environmental and safeguards samples.     

电感耦合等离子体质谱技术最新进展

对1998年以来电感耦合等离子体质谱技术（ICP－MS）的最新进展作一简要回顾。内容包括同位素比值分析、双聚焦扇形磁场高分辨ICP－MS、多接收器磁扇形等离子体质谱仪（MC－ICP－MS）、飞行时间等离子体质谱仪（ICP－TOF－MS）、“冷”等离子体及屏蔽炬技术以及动态碰撞／反应池技术等进展。     

Detection efficiencies in nano- and femtosecond laser ablation inductively coupled plasma mass spectrometry

Detection efficiencies of laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS), defined as the ratio of ions reaching the detector and atoms released by LA were measured. For this purpose, LA of silicate glasses, zircon, and pure silicon was performed using nanosecond (ns) as well as femtosecond (fs) LA. For instance, ns-LA of silicate glass using helium as in-cell carrier gas resulted in detection efficiencies between approximately 1E-7 for low and 3E-5 for high mass range elements which were, in addition, almost independent on the laser wavelength and pulse duration chosen. In contrast, the application of argon as carrier gas was found to suppress the detection efficiencies systematically by a factor of up to 5 mainly due to a less efficient aerosol-to-ion conversion and ion transmission inside the ICP-MS.     

Study of heterogeneities in steels and determination of soluble and total aluminium and titanium concentration by laser ablation inductively coupled plasma mass spectrometry

A methodology for bulk analysis of Al and Ti and for determination of soluble and total Al and Ti concentration in steel samples by laser ablation inductively coupled plasma mass spectrometry was developed. The spatial distribution (both at surface and within the sample) of the insoluble fraction of Al and Ti was also qualitatively estimated. Certified reference materials (CRMs) SS-451 to 460 (carbon steel) and 064-1 (Nb/Ti interstitial free steel), from BAS, and JK 2D (carbon steel) and JK 37 (highly alloyed steel), from SIMR, were studied. It was demonstrated that the insoluble fraction of Al and Ti is heterogeneously distributed. A series of nine glass samples (fused beads) with fixed Fe content and different Al and Ti contents was prepared by melting appropriate amounts of Fe₂O₃, Al₂O₃ and TiO₂ with a lithium tetraborate–sodium carbonate mixture. Quantitative determinations were performed by using calibration graphs obtained from the synthetic fused beads, with ⁵⁷Fe as internal standard; line scan laser sampling mode was used, focusing the laser beam at the sample surface. The optimized laser operating parameters were: laser pulse energy of 1.5 mJ, pulse repetition rate of 5 Hz, scanning speed of 5 μm s⁻¹ and preablation time of 20 s. The concentrations obtained for bulk analysis of CRM samples corresponded with the certified values within the experimental uncertainty. An acceptable concordance between certified and found values was attained for the determination of soluble and total Al and Ti in CRM 064-1 sample.     

Serum/plasma methylmercury determination by isotope dilution gas chromatography-inductively coupled plasma mass spectrometry

A method for the determination of methylmercury in plasma and serum samples was developed. The method uses isotope dilution with ¹⁹⁸Hg-labeled methylmercury, extraction into dichloromethane, back-extraction into water, aqueous-phase ethylation, purge and trap collection, thermal desorption, separation by gas chromatography, and mercury isotope specific detection by inductively coupled plasma mass spectrometry. By spiking 2 mL sample with 1.2 ng tracer, measurements in a concentration interval of (0.007–2.9) μg L⁻¹ could be performed with uncertainty amplification factors <2. A limit of quantification of 0.03 μg L⁻¹ was estimated at 10 times the standard deviation of concentrations measured in preparation blanks. Within- and between-run relative standard deviations were <10% at added concentration levels of 0.14 μg L⁻¹, 0.35 μg L⁻¹ and 2.8 μg L⁻¹, with recoveries in the range 82–110%. Application of the method to 50 plasma/serum samples yielded a median (mean; range) concentration of methylmercury of 0.081 (0.091; <0.03–0.19) μg L⁻¹. This is the first time methylmercury has been directly measured in this kind of specimen, and is therefore the first estimate of a reference range.     

Laser ablation single-collector inductively coupled plasma mass spectrometry for lead isotopic analysis to investigate evolution of the Bilbilis mint

This work explores the performance of laser ablation—inductively coupled plasma mass spectrometry using different types of single-collector devices (sector field and time-of-flight instrumentation) for lead isotopic analysis of bronze coins, minted in the ancient city of Bilbilis. The aim of the study was achieving sufficient discrimination power to reveal similarities and differences for coins originating from different historical periods, and to obtain information on the possible source of the lead ores used in their production, while restricting the damage inflicted to the samples such that it is not visible to the naked eye.It was found that satisfactory results (RSD in the 0.15-0.30% range for ²⁰⁷Pb/²⁰⁶Pb and ²⁰⁸Pb/²⁰⁶Pb ratios) could be finally obtained, despite the noisy nature of signals generated upon ablation of the highly inhomogeneous coins, by means of a methodology based on: (a) selection of the line profiling ablation mode; (b) use of a dual pass spray chamber that permits the simultaneous introduction of a solution (containing thallium of known isotopic composition), thus resulting in a wet plasma that showed an increased robustness towards matrix effects and (c) detection using a TOF-ICPMS unit, which proved to be much better suited to deal with the transient signals obtained, while being also sufficiently sensitive to obtain good counting statistics, owing to the high lead level (average around 5%) present in the samples. Moreover, under these conditions, the simultaneous aspiration of the thallium spike permitted accurate correction for mass discrimination, such that it was not necessary to use external matrix-matched standards for calibration.     

电感耦合等离子体质谱激光烧蚀固体进样技术新进展

本文简单地介绍了电感耦合等离子体质谱(LA-ICP-MS)的基本原理及装置。分别对LA-ICP-MS在飞秒激光器、紫外激光器、固液气溶胶混合进样、集合式小样品标样、原位统计分布技术上的技术新进展进行了详细的评述。     

Inductively coupled plasma mass spectrometry (ICP MS): a versatile tool

Inductively coupled plasma (ICP) mass spectrometry (MS) is routinely used in many diverse research fields such as earth, environmental, life and forensic sciences and in food, material, chemical, semiconductor and nuclear industries. The high ion density and the high temperature in a plasma provide an ideal atomizer and element ionizer for all types of samples and matrices introduced by a variety of specialized devices. Outstanding properties such as high sensitivity (ppt-ppq), relative salt tolerance, compound-independent element response and highest quantitation accuracy lead to the unchallenged performance of ICP MS in efficiently detecting, identifying and reliably quantifying trace elements. The increasing availability of relevant reference compounds and high separation selectivity extend the molecular identification capability of ICP MS hyphenated to species-specific separation techniques. While molecular ion source MS is specialized in determining the structure of unknown molecules, ICP MS is an efficient and highly sensitive tool for target-element orientated discoveries of relevant and unknown compounds. This special-feature, tutorial article presents the principle and advantages of ICP MS, highlighting these using examples from recently published investigations.     

激光烧蚀-电感耦合等离子体质谱法测定塑料中的Pb、Cd、Cr和Hg

采用激光烧蚀固体进样技术的电感耦合等离子体质谱法(LA-ICP-MS)测定了塑料中的Pb、Cd、Cr和Hg。选择了线扫描激光烧蚀方式,并从灵敏度和稳定性角度优化了工作参数。根据计算分馏因子考察了分馏效应,结果表明,所测元素分馏效应小。塑料中Hg的记忆效应严重,认为主要来自样品表面吸附,减小样品的表面积可减小Hg的记忆效应。以聚丙烯标准物质及其空白片作校准曲线,应用于ABS、PPS、PA66+30%GF、PVC、PTFE等实际塑料样品的测定,测定结果与ICP-OES(XRF)法测定值基本吻合。Pb、Cd、Cr和Hg的检测下限分别为0.002、0.001、0.08和1.5 mg/kg。     

A magnesium hydroxide preconcentration/matrix reduction method for the analysis of rare earth elements in water samples using laser ablation inductively coupled plasma mass spectrometry

This paper describes a simple method for simultaneous preconcentration and matrix reduction during the analysis of rare earth elements (REEs) in water samples through laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS). From a systematic investigation of the co-precipitation of REEs using magnesium hydroxide, we optimized the effects of several parameters - the pH, the amount of magnesium, the shaking time, the efficiency of Ba removal, and the sample matrix - to ensure quantitative recoveries. We employed repetitive laser ablation to remove the dried-droplet samples from the filter medium and introduce them into the ICP-MS system for determinations of REEs. The enrichment factors ranged from 8 to 88. The detection limit, at an enrichment factor of 32, ranged from 0.03 to 0.20 pg mL⁻¹. The relative standard deviations for the determination of REEs at a concentration of 1 ng mL⁻¹ when processing 40 mL sample solution were 2.0-4.8%. We applied this method to the satisfactory determination of REEs in lake water and synthetic seawater samples.