Novel polystyryl resins for size exclusion chromatography

New size exclusion chromatography (SEC) resins based on a crosslinker having independent vinyl groups have been produced and compared with SEC resins based on divinylbenzene-55 (DVB). 1,2-Bis(p-vinylphenyl)ethane (p,p-BVPE) and its meta-isomers were suspension-copolymerized with p-methylstyrene in the presence of different porogens to give particles of about 5 μm average diameter. The porous particles were slurry-packed into stainless steel columns for SEC evaluation. Calibration curves were obtained using narrow disperse polystyrene standards with molecular weights ranging from 580 to 3,040,000. The calibration curves for the new BVPE resins covered wider useful molecular weight ranges than those for comparable divinylbenzene resins. Particle size, surface morphology and the properties of pores were studied using a Coulter Multisizer II, scanning electron microscopy, nitrogen adsorption, and mercury porosimetry. © 1994 John Wiley & Sons, Inc.     

Error introduced into determination of pore size distribution by size exclusion chromatography

Simultaneous use of large standard molecules and small particles of the product examined gives rise to errors in pore size determination by size exclusion chromatography. This error is calculated for packings of spherical particles, thus making corrections possible.     

Evidence of aggregation in dilute solution of amphoteric poly(amido-amine)s by size exclusion chromatography

Evidence of aggregation of amphoteric linear poly(amido-amine)s (PAAs) was proved using a multi-angle laser light scattering detector on-line to a size exclusion chromatography (SEC) system. As a rule the PAAs chemical structure, with the presence of charged groups that are both anionic and cationic, easily generates aggregation and non-steric fractionation. A non-amphoteric, non-aggregate PAAs polymer with an elution pattern close to ideal SEC was also obtained and characterized for comparison. The influence of PAAs synthesis conditions on the extent of aggregation was also studied.     

Pore structure characterization of organic-inorganic materials by inverse size exclusion chromatography

Summary In Inverse Size (or Steric) Exclusion Chromatography (ISEC) measurements, the investigated material is used as a stationary phase in a chromatographic column and the elution volumes of a series of standard solutes with different molecular size are measured. By an appropriate choice of mobile phase and type of standard solutes, specific (enthalpic) interactions between investigated material and solutes are eliminated so that the elution volumes depend on the porous structure of the column filling only. Then, a mathematical treatment of elution data can provide detailed information on both the macropores and the microporous structure of e.g. a swollen polymer gel in a polymer that is grafted onto silica. The basic principle of the evaluation of porosimetric information from chromatographic data is the assumption that the real porous structure of an investigated sample can be modelled as a collection of discrete pore fractions, each containing pores of different but uniform size and of simple geometrical shape. Problem then is to determine the combination of volumes of these fractions which yields the best agreement between computed and experimental values of the elution volumes of standard solutes. It is possible to perform the ISEC measurements either in an organic solvent or non-solvent (e.g. tetrahydrofuran or methanol) or in water, depending on the compatibility of the investigated material with the respective environment. For non-polar polymers, like copolymers of styrene and divinylbenzene, the use of tetrahydrofuran as the mobile phase with alkanes and polystyrenes as standard solutes has been recommended. Alternative ISEC investigation of the same material in an organic and an aqueous environment can provide additional information on its lipo- or hydrophilicity. This method has provided specific information, not obtainable by mercury porosimetry, when modifying silica by a coupling agent, polymerizing different monomers to different extents.     

Studies on the refolding of the reduced-denatured insulin with size exclusion chromatography

The refolding of the reduced-denatured insulin from bovine pancreas was investigated with the size exclusion chromatography (SEC). It was shown that the reduced-denatured insulin originally denatured with 7.0 mol·L-1 guanidine hydrochloride (GuHCI) or 8.0 mol·L-1 urea could not be refolded with a non-oxidized mobile phase. Although the oxidized and reduced glutathione (GSSG and GSH) were employed in the oxidized mobile phase, the reduced-denatured insulin still could not be renatured. However, in the presence of 2.0 mol·L-1 urea in the oxidized mobile phase employed, the reduced-denatured insulin can be refolded with SEC, and the aggregation of denatured insulin can be diminished by urea. In addition, the disul-fide exchange of reduced-denatured insulin also can be accelerated with GSSG/GSH in the oxidized mobile phase. The three disulfide bridges of insulin were formed correctly and the reduced-unfolded insulin can be renatured completely. The results were further tested with re-versed-phase liquid chromatography (RPLC) and hydrophobic interaction chromatography (HIC).     

Columns switch recycling size exclusion chromatography for high resolution protein separation

Columns switch recycling size exclusion chromatography (csrSEC) was proposed to achieve high resolution protein separation with good biocompatibility. Proteins were firstly separated by two serially coupled SEC columns, and fractions were in sequence switched back to the first column by two-position valves for further separation in terms of close-loop recycling until satisfactory resolution was achieved. Compared to SEC, the separation window was broadened by increasing column length via cycling without further increase on back pressure. Compared to recycling SEC (rSEC), the overtaking of later eluted components by early eluted ones after several cycles could be avoided for complex sample analysis, by parking fractions in the second SEC column before transferred in turn back to the first one for cycling ordinally. In our experiments, the baseline separation of five proteins with molecular weight ranging from 10 kDa to 80 kDa was achieved by csrSEC. Furthermore, a multidimensional csrSEC–RPLC platform was constructed, and peak capacity up to 3600 was obtained for protein separation. All these results demonstrated that csrSEC is a promising protein separation mode with good biocompatibility, broadened separation window and improved resolution.     

Enthalpy assisted size exclusion chromatography. Part 2. Adsorption retention mechanism

A novel high performance liquid chromatographic method for separation of synthetic polymers has been tested. It involves combination of the enthalpic and entropic retention mechanisms, resulting in increased selectivity of separation within a specific molar mass range. In this present case, the enthalpic retention mechanism is adsorption of macromolecules on a bare silica gel column packing. Under critical conditions of enthalpic interactions, homopolymers are known to elute irrespective of their molar mass. However, in the vicinity of critical conditions, a situation can be identified when retention volumes (V(R)) rapidly decrease with increasing molar mass. Typically, this happens for polymer species close to or above their exclusion limit observed with the same column in the absence of enthalpic interactions between macromolecules and packing, that is near "ideal SEC" conditions. The dependence of polymer retention volume on molar mass closely resembles size exclusion conditions. However, the witnessed rate of change in V(R )with polymer molar mass is more pronounced, thus indicating increased selectivity of separation. This situation not only offers the benefit of more selective separation according to molar mass but efficient discrimination of macromolecules possessing different nature and interactivity with the column packing can be accomplished as well.     

Electrically driven capillary size exclusion chromatography

Summary Electrically driven size exclusion chromatography (ED-SEC) of polystyrenes in packed capillaries using dimethylformamide as solvent is demonstrated. The efficiency and retention behaviour of polystyrenes under pressure and electro drive were investigated. Under pressure drive the plate height (H) increases steadily with increasing linear velocity (u) whereas under electro drive the H-u curves largely coincide and are very flat. At higher velocities the plate heights are about 50% smaller with electro drive than with pressure drive. Calculations show that with increasing ionic strength, the flow through the particles may increase causing a clear diminishing of the elution window.     

Interlaced size exclusion liquid chromatography of monoclonal antibodies

Size exclusion chromatography is a widely performed analysis of monoclonal antibodies, primarily used to monitor the levels of higher weight molecular species such as aggregates. Owing to the subtleties of these separation mechanisms and frequently observed partial resolutions of components in these separations, many common methods for increasing the method throughput are not practical as they trade off resolution for speed. Short columns, high flow rates and smaller particles are examples of these approaches. In this paper a practical method is demonstrated for injecting samples onto the column in rapid succession and gating the detection window to monitor the elution of each sample individually. At any given instant approximately two samples are eluting through the column. By co-ordinating the injection and detection time windows the samples can be kept discrete and significant throughput enhancements achieved, up to nearly 2-fold improvements are demonstrated. A rudimentary theory is development to show that the throughput improvements can be predicted to approximation by simple column characteristics. Experimental results for a series of monoclonal antibodies demonstrate the equivalency of the method to a conventional injection approach, the throughput increase, and the robustness of the method.     

Analysis of pesticide residues in tobacco with online size exclusion chromatography with gas chromatography and tandem mass spectrometry

An ultrasensitive method for the simultaneous analysis of pesticides residues in tobacco was developed with online size exclusion chromatography with gas chromatography and tandem mass spectrometry. Tobacco samples were extracted with the solvent mixture of cyclohexane and acetone (7:3, v/v) and centrifuged. Then, the supernatant liquors were injected directly into the online size exclusion chromatography with gas chromatography and tandem mass spectrometry without any other purification procedures after being filtered with a 0.22 μm organic phase filter. The matrix interferences were effectively removed and recoveries of most pesticides were in the range of 72–121%. Especially, for chlorothalonil, the analysis efficiency of this method was much more favorable than that of the general method, in which dispersive solid‐phase extraction was used as an additional purified procedure. In addition, the limits of quantitation of this method were from 1 to 50 μg/kg. Therefore, a rapid, cost‐effective, labor‐saving method was proposed in the present work, which was suitable for the analysis of 41 pesticide residues in tobacco.     

体积排阻色谱法测定低分子量肝素抗凝血因子Xa的活性

发展了一种基于体积排阻色谱测定低分子量肝素(LMWH)抗凝血活性的方法。利用肝素与抗凝血酶Ⅲ(ATⅢ)结合后可增强ATⅢ对凝血因子Xa(FXa)抑制作用的原理,通过测定加入LMWH后FXa水解其生色底物产生对硝基苯胺(pNA)这一反应的抑制程度确定LMWH的活性。首先将含有一定浓度LMWH的缓冲溶液与ATⅢ溶液混合,然后依次加入FXa和生色底物,分别孵育一段时间。底物被FXa水解,产生游离的pNA。体积排阻色谱可将小分子产物pNA与其他大分子分离开,因而可以在pNA的最大吸收波长下得到高灵敏度的测定,并且不再受其他成分的干扰。该方法重复性好,灵敏度高,极大地减少了样品的消耗量,降低了成本,并且还可进行各种复杂样品(如血浆)中LMWH抗FXa活性的监测。     

低分子量硫酸化多糖的体积排阻色谱法分离及其组成定量分析

建立了用于分离并定量测定低分子量硫酸化多糖中不同糖链数的各个组分分布比例的体积排阻色谱方法。系统考察了流动相的组成、离子强度和pH值、流速、柱温等因素对分离的影响。最佳分离条件: 两支TSK-GEL G2000 SWxl色谱柱(300 mm×7.8 mm)串联,流动相100 mmol/L Na2HPO4-NaH2PO4 (pH 7.0),流速0.5 mL/min,柱温35 ℃,进样量5 μL,样品质量浓度10 g/L。在最佳的分离条件下,可以将低分子量硫酸化多糖样品中不同糖链数的各个组分分离并对各个组分的分布进行了定量分析。用该方法对美国药典标准品(USP)、商品和实验室制备的低分子量硫酸化多糖糖链数分布进行了定量化比较,证明该方法可用于低分子量硫酸化多糖类药物的组成成分的质量控制。     

Calibration of ultrafiltration membranes against size exclusion chromatography columns

Using the extension of the concept of universal calibration parameter, yielding a relation between the hydrodynamic volume of molecules and the elution volume in size exclusion chromatography (SEC), to retention coefficients in ultrafiltration (UF), we propose a direct calibration of UF membranes against chromatography columns. Plotting the retention coefficient by one given UF membrane of a series of probe molecules versus their elution volume in SEC chromatography provides a calibration curve for this membrane. For a wide range of retentions, such calibration can be directly used to predict the retention of any molecule: one only needs to measure its exclusion volume by the SEC column, and read the retention by the calibrated membrane on the calibration curves.     

Automated sample cleanup using on-line coupling of size exclusion chromatography to high resolution gas chromatography

A fully automated on-line sample cleanup system based on the coupling of size exclusion chromatography to high resolution gas chromatography is described. The transfer technique employed is based on fully concurrent solvent evaporation using a loop-type interface, early vapor exit and co-solvent trapping. Optimization of the LC-GC transfer was done visually via an all-glass oven door. To circumvent the problem of mixing within the injection loop, an adaptation was made to the standard loop-type interface. The determination of a series of additives in a polymer matrix is presented as one example of the vast range of applications opened up by this technique.     

Accessibility of the gel phase in macroporous network polymers: A comparison of the fluorescence probe and inverse steric exclusion chromatography techniques

Two independent methods of analysis were employed to evaluate accessibility of the gel phase in macroporous network polymers. Fluorescence probes, covalented incorporated into the gel during polymerization, can provide a qualitative assessment of accessible surface area from an analysis of the solvatochromic shift of fluorescence emission. These findings are corroborated by inverse steric exclusion chromatography (ISEC). The data permits quantification of the polymers surface character in the solvated state. The results call attention to the inadequacy of dry surface area technique (e.g., BET analysis) in providing information of this type.     

Analysis of sodium polycarboxylates in detergents by size exclusion chromatography

Summary This paper describes the quantitative analysis and preparative isolation of sodium polycarboxylates in detergents by means of gel permeation chromatography. An analytical monitoring method separates the polymers from other low molecular detergent ingredients within 10 minutes. There is no separation of the various molecular weight polycarboxylate macromolecules themselves. They elute from the column as a single narrow peak at the exclusion volume. A second preparative gel filtration method allows isolation of polycarboxylates in amounts necessary for further characterization. Appropriate sample pretreatments and possible interferences are discussed.     

Monte Carlo simulation of size exclusion chromatography for randomly branched and crosslinked polymers

The elution curves of size exclusion chromatography for nonlinear polymers formed through random branching and crosslinking of long polymer chains were simulated with a Monte Carlo method. We considered two types of measured molecular weight distributions (MWDs): (1) the MWD calibrated relative to standard linear polymers and (2) the MWD obtained with a light scattering (LS) photometer in which the weight‐average molecular weight of polymers within the elution volume is determined directly. The calibrated MWDs clearly underestimate the molecular weights for both randomly branched and crosslinked polymers, and this technique can be used to assess the degree of deviation from the true MWD. When the primary chains conform to the most probable distribution, the calibrated MWD can be estimated reasonably well with the Zimm–Stockmayer equation for the g factor with the help of the relationship between the average number of branch points per molecule and the degree of polymerization. However, the LS method gives good estimates of the true MWD for both randomly branched and crosslinked polymers, although the agreement is better for the branched ones. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2009–2018, 2000