K-2N双受主共掺杂P型ZnO的第一性原理研究

本文采用基于第一性原理的密度泛函理论(DFT)平面波超软赝势方法,计算了未掺杂ZnO和K,K-2N掺杂ZnO体系的晶体结构、能带、电子态密度与光学性质.研究表明:K掺杂ZnO体系,带隙变宽,在费米能级附近引入了较浅的受主能级,费米能级进入到价带中.而K-2N共掺杂体系中,带隙变窄,形成了浅受主能级,这个对改善ZnO的p...     

Al-N共掺杂ZnO电子结构和光学性质

基于密度泛函理论的第一性原理,分析了Al-N共掺杂ZnO的电子结构和光学性质。计算了Al-N复合体共掺ZnO的结合能,发现Al-N复合体可以在ZnO中稳定存在,因此Al-N共掺可以提高N在ZnO的固溶度。研究表明:N掺杂ZnO体系,由于N-2p和Zn-3d态电子轨道杂化作用,在费米能级附近引入深受主能级,价带顶和导带底发生位移,导致禁带宽带变窄。而Al-N共掺杂体系,适当控制Al和N的比例,克服了N单掺杂时受主间的相互排斥,降低了受主能级,对改善ZnO的p型掺杂有重要意义。在Al-N共掺ZnO中,Al的引入,导致共掺体系的禁带宽度减小,吸收带边红移,实验现象证实了这一结果。     

Sc掺杂ZnO的电子结构和光学性质的影响

本文采用基于第一性原理的密度泛函理论（DFT）平面波超软赝势方法，研究了Sc掺杂ZnO体系的晶体结构、电子结构和光学性质。在对Sc掺杂结构优化的基础上对其进行了数值模拟计算，结果表明：随着Sc原子的掺入，体系的晶格常数稍微变大，键长变长，体积变大，系统总能增大，费米能级进入导带，体系逐渐呈金属性，带隙变宽且随着掺杂浓度增大而增大。另一方面，掺杂后ZnO的光学性质也发生了一定变化，ZnO吸收谱中出现了新的吸收峰，吸收边蓝移，同时介电函数虚部也出现了新的波峰。     

p型Na掺杂各向异性ZnO的电子性质与热电输运性质

采用密度泛函理论的第一性原理计算研究了p型Na掺杂各向异性ZnO的能带结构、光学性质、介电性质、总态密度和不同原子的分态密度,并系统分析了其热电输运性质。计算分析结果表明,p型Na掺杂ZnO为p型直接带隙半导体,其带隙增大到1.3eV,其对于光子的吸收限向低能量光子移动,体系费米能级附近的态密度大幅度提高,这主要是p态电子贡献的;在费米能级附近的导带和价带中都出现了新的能级,这些新的能级主要由Nas、Nap、Znp、Znd和Op电子形成,且他们之间存在着强耦合相互作用。Na掺杂ZnO的电输运性质具有各向异性;其价带和导带中的载流子有效质量均较大;载流子输运主要由Nas、Nap、Znp和Op电子完成。     

不同Yb掺杂浓度的ZnO的电子结构与光学特性

本文基于密度泛函理论(DFT)框架下的第一性原理计算方法,研究了不同Yb浓度掺杂ZnO体系的电子结构和光学性质.计算得到的结果证明,Yb掺杂ZnO后会造成电子结构和光学性质的明显改变.增加掺杂浓度使能带带隙逐渐变窄,其费米能级向上移动到导带,表现出n型半导体的特性;在Yb-4f态导带附近的带隙中产生了新的缺陷,同时观察到更好的吸收系数和折射率.因此,Yb掺杂ZnO对其电子性质和光学结构有很大的影响,为进一步深入了解掺杂ZnO性质的影响提供理论基础.     

不同Yb掺杂浓度的ZnO的电子结构与光学特性

本文基于密度泛函理论(DFT)框架下的第一性原理计算方法,研究了不同Yb浓度掺杂ZnO体系的电子结构和光学性质.计算得到的结果证明,Yb掺杂ZnO后会造成电子结构和光学性质的明显改变.增加掺杂浓度使能带带隙逐渐变窄,其费米能级向上移动到导带,表现出n型半导体的特性;在Yb-4f态导带附近的带隙中产生了新的缺陷,同时观察到更好的吸收系数和折射率.因此,Yb掺杂ZnO对其电子性质和光学结构有很大的影响,为进一步深入了解掺杂ZnO性质的影响提供理论基础.     

浓度对Co掺杂ZnO的影响的第一性原理研究

采用基于密度泛函理论的第一性原理平面波超软赝式方法,详细研究了本征ZnO和Co掺杂ZnO的电子结构和光学性质。计算结果表明,Co掺入ZnO后,Co的大部分3d电子位于费米能级附近,O的2p轨道电子发生分裂,并进入费米能级与Co的3d电子发生杂化,价带电子向低能级端移动,带隙变大,但随掺杂浓度的增大这种现象并不明显。另外ZnO掺Co后,由于Co的3d电子的引入,使得吸收谱中出现新的吸收峰,并发生蓝移现象,这与实验得到的结果相一致;静态介电常数明显增大,但随掺杂浓度的增大基本保持不变。     

稀土元素(Y,La)掺杂ZnO的电子结构和光学性质

采用基于密度泛函理论的第一性原理平面波超软赝势方法,计算了未掺杂ZnO和稀土(Y,La)掺杂ZnO体系的空间结构、能带、电子态密度与光学性质.结果表明,掺杂后体系的形成能减小,稳定性变强,带隙展宽,费米能级进入导带中,体系呈金属性,载流子发生简并,形成简并半导体.定性分析了掺杂后光学性质的变化. 关键词： 氧化锌 掺杂 第一性原理     

AZO(ZnO:A1)电子结构与光学性质的第一性原理计算

计算了不同Al掺杂浓度下ZnO体系电子结构和光学属性.分析了掺杂对AZO(ZnO:A1)晶体结构、能带、态密度、光学性质的影响.所有计算都是基于密度泛函理论框架下的第一原理平面波赝势方法.计算结果表明:Al掺杂ZnO在导带底引入了大量由掺杂原子贡献的导电载流子,明显提高了体系的电导率.费米能级进入导带.同时,光学性质的计算表明光学带隙明显展宽,且向低能方向漂移;AZO透明导电材料的光学透过率在可见光范围内高达85%,紫外吸收限随着掺杂浓度的增加而发生蓝移.所有计算表明AzO材料可作为优良的透明导电薄膜材料.     

贵金属（Cu、Ag、Au）掺杂ZnO电子结构和光学性质的第一性原理研究

采用基于密度泛函理论的总体能量平面波超软赝势方法,对贵金属（Cu、Ag、Au）掺杂ZnO进行了几何结构优化,并计算了相应的能带结构、受主能级、形成能、电子态密度和光学性质. 结果表明：贵金属掺杂后带隙增加且体系费米能级附近电子态密度主要来源于Cu3d、Ag4d和Au5d态电子的贡献. 与未掺杂ZnO相比,介电函数虚部、反射峰强度和吸收系数在可见光和紫外区域增强. 能量损失谱计算表明,贵金属（Cu、Ag、Au）掺杂后ZnO的等离子体共振频率峰发生蓝移.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.