Determination of aluminium in silicon by electrothermal atomic absorption spectrometry

The sample is decomposed with hydrofluoric and nitric acids and the diluted solution is injected into the graphite furnace. For a 100-mg sample, the detection limit (3 σ) is 1.2 μg AI g^-1. The coefficient of variation is 3–13% for 9–7000 μg Al g^-1 in silicon.     

Determination of selenium in small volumes of blood plasma and serum by electrothermal atomic absorption spectrometry

A graphite-furnace atomic absorption spectrometric method is described for the determination of selenium in blood plasma and serum. Samples are diluted (1 + 9) with a solution containing nickel and nitric acid and measured by a standard additions method. Repeatability for a serum sample containing 87 μg Se l^-1 was 4.4%. The mean recovery of selenium(IV) from a human protein solution was 97.5%. The method was further tested in an interlaboratory comparison study. The standard additions procedure requires a sample volume of 200 μl and a total time of about 7.5 min. A secondary calibration graph can be used, however, resulting in increased throughput up to 13 samples per hour, and a decrease in the sample volume needed to 100 μl.     

Determination of lithium in human serum by electrothermal atomic absorption spectrometry

An efficient method was developed for the determination of nanogram levels of lithium in biological samples. Serum samples from human subjects from southeastern Spain, treated or not treated with lithium carbonate, were analyzed by electrothermal atomic absorption spectrometry. The samples were previously treated with a matrix modifier consisting of 0.1% Triton X-100 and injected through a graphite tube with L'vov platform. The Li concentrations measured by the procedure described for the 3 certified reference samples used were not significantly different (p > 0.05) than certified levels. Sample recoveries and variability during several days, with coefficients of variation from 4.00 to 14.8%, demonstrated the reliability and accuracy of this technique. Mean Li concentration determined in the serum of individuals with psychiatric disorders treated with Li (n = 117, 5.077 +/- 1.795 microg Li/mL) was significantly higher (p < 0.001) than that in individuals not treated with Li (n = 24, 1.902 +/- 2.054 ng Li/mL).     

Direct determination of arsenic in blood serum by electrothermal atomic absorption spectrometry

A method for the direct determination of arsenic in human blood serum is described. To suppress loss of arsenic by volatilization anal to remove chemical interferences in graphite-furnace atomic absorption spectrometry, the formation of involatile compounds with graphite, or with a matrix modifier is tested. With aqueous solutions, two sorts of interactions between graphite and arsenic are shown. But, in presence of serum, these interactions do not occur, Among 18 matrix modifiers tested, nickel gives the best sensitivity when used at high concentrations in the presence of Triton X-100. The proposed method allows direct arsenic determination, based on calibration with aqueous solutions. The method is applied to the serum of 20 normal subjects. The limit of detection is 0.4 μg l^?1 arsenic.     

Determination of manganese in serum and urine by electrothermal atomic absorption spectrometry

Manganese is determined in serum and urine by graphite-furnace atomic absorption spectrometry after dilution (1 + 1) with distilled water. Simple aqueous standards are used for calibration. Background absorption from the matrix is decreased by attention to the heating programme, sample dilution and gas flow-rate during atomisation. Remaining background absorption is removed by a deuterium-arc background correction system. To obtain accurate results, great care is needed in collecting samples to avoid contamination. Blood is collected through a plastic cannula, because stainless steel needles introduce considerable contamination. The mean normal concentration of manganese in serum was found to be 0.58 μg l^?1 (it- = 9) which is in agreement with other literature values. For urine, the mean normal concentration found was 0.7 μg l^?1 (it- = 16). Patients on total parenteral nutrition with manganese supplements show elevated serum and urine manganese concentrations.     

Determination of lead in blood by tungsten coil electrothermal atomic absorption spectrometry

A method for the determination of lead in blood using a tungsten coil atomizer is described. A 100 μl volume of the whole blood sample is transferred to a sampler cup containing 100 μl of water plus 300 μl of 0.25% v/v Triton X-100. After lysis of blood cells, 500 μl of 10% w/v trichloroacetic acid is added for protein precipitation and 10 μl of the supernatant solution is automatically delivered into the tungsten coil. The furnace heating program is implemented in 41 s. It is shown by the paired t-test that there is no significant difference at the 5% probability level between results obtained by the proposed method and by using a transversely heated graphite atomizer with a longitudinal Zeeman background correction. Accuracy is also assessed by employing reference materials. The proposed tungsten coil procedure presents a characteristic mass of 15 pg Pb and a detection limit of 1.9 μg Pb dl⁻¹.     

Determination of aluminium and chromium in serum by atomic absorption spectrometry

Summary The optimal conditions for the determination of aluminium and chromium in blood serum are proposed. Several sample pretreatment procedures for the purpose are compared. The best results are obtained by sample dilution with nitric acid (0.1 mol/l) and addition of Mg(NO₃)₂ as modifier with a magnesium concentration of 0.2 mg/ml. This procedure has been used for studying the intestinal intake of aluminium by patients after oral administration of aluminium compounds.     

Determination of aluminium and chromium in slurried baby food samples by electrothermal atomic absorption spectrometry

Electrothermal atomic absorption spectrometry was used to determine aluminium and chromium in different types of baby foods. Samples without previous treatment were introduced into the atomizer as suspensions, which were prepared in a medium containing 0.1% (w/v) Triton X-100 (for chromium) or 10% (v/v) ethanol (for aluminium), 5% (v/v) concentrated hydrogen peroxide, and 0.5% (v/v) concentrated nitric acid. The slurries were homogenized with a potter and introduced directly into the furnace. The presence of nitric acid allowed a substantial amount of analyte to be extracted to the liquid phase. No matrix effect was observed and aqueous standard solutions were used for calibration. The detection limits were 4 and 50 pg for chromium and aluminium, respectively; characteristic masses were 3.8 pg for chromium and 18 pg for aluminium. Reliability of the procedures was checked by statistically comparing the results with those obtained with a previous microwave oven mineralization stage and by analyis of several certified reference materials. Values for the aluminium content ranged between 0.4 and 3.0 microg/g, and for chromium between 0.003 and 0.06 microg/g.     

Screening for vanadium in urine and blood serum by electrothermal atomic absorption spectrometry and D.C. plasma atomic emission spectrometry

Practical detection limits were 2 and 10 μg l^?1 vanadium for pyrolyte graphite-furnace a.a.s. and d.c.p.-a.e.s., respectively, which allowed screening for urinary vanadium (? 10 μg ?in ? subjects, by direct measurements. Extraction of vanadium with ammonium 1?inecarbodithioate into 4-methylpentan-2-one gave detection limits of 0.5 and ? μg l^?1 vanadium, respectively, for the two techniques.     

Analysis of cobalt in plasma by electrothermal atomic absorption spectrometry

Summary A method for the determination of traces of cobalt in plasma is described. The sample is digested in a test tube using a mixture of nitric and perchloric acid. Ammonium-pyrrolidine dithiocarbamate is added as chelating agent, and after pH-adjustment to pH 9±0.1, cobalt is extracted into methyl-isobutyl ketone.Recovery studies using Co-60 showed that losses of cobalt during the procedure, including digestion and extraction are less than 3%. Possible contamination from the steel needle used is tested and discussed. The coefficient of variation for the method is 9.5% at the 0.20 g/l level. A realistic determination limit following this procedure is estimated to be 0.06 g/l. Using this method, the cobalt concentration in plasma from 32 control persons was determined to 0.15 ±0.07 g/l. For 10 refinery workers daily exposed to aerosols of CoCl₂ the determined average was 9.7±7.1 g/l.

---

Analyse von Kobalt in Plasma mit Hilfe der elektrothermischen AAS

Zusammenfassung Bei dem beschriebenen Verfahren wird die Probe mit Hilfe von Salpetersäure/Perchlorsäure aufgeschlossen. Als Komplexierungs-Reagens wird Ammonium-pyrrolidindithiocarbamat zugefügt und nach pH-Einstellung auf 9±0,1 wird Co mit Methylisobutylketon extrahiert.Mit Hilfe von Co-60 wurde festgestellt, daß die durch Aufschluß und Extraktion verursachten Verluste weniger als 3% betragen. Eine mögliche Verunreinigung durch die benutzten Stahlnadeln wurde untersucht und diskutiert. Der Variationskoeffizient beträgt 9,5% bei 0,2 g Co/l. Die Bestimmungsgrenze nach diesem Verfahren liegt bei 0,06 g Co/l. Die Kobaltkonzentration im Plasma von 32 Kontrollpersonen wurde zu 0,15±0,07 g Co/l bestimmt. Für 10 Raffineriearbeiter, die täglich CoCl₂-Aerosolen ausgesetzt waren, wurde ein Durchschnitt von 9,7±7,1 g Co/l gefunden.

     

Determination of selenium in water by electrothermal atomic absorption spectrometry

Summary The electrothermal atomization of selenium has been investigated for the accurate determination of selenium in water samples. Hydrogen seriously affects the atomization temperature of selenium in a molybdenum micro-tube atomizer. The atomization of selenium also suffers from serious interferences caused by salts and other elements. The extraction of selenium diethyldithiocarbamate complex serves to eliminate the interferences from the matrix. The addition of copper allows the suppression of interferences from elements extracted with selenium. The method permits the determination of selenium(IV) and selenium(VI) separately.This research was in part funded by the Ministry of Education, Science and Culture, Japan, under Grant-in-Aid for Scientific Research, for which we express our appreciation.     

Determination of vanadium in urine by electrothermal atomic absorption spectrometry

After wet ashing of the urine sample with nitric acid, vanadium is chelated with cupferron, extracted into 4-methylpentan-2-one and determined by atomic absorption spectrometry with a pyrolytically-coated graphite furnace atomizer. The sensitivity allows the precise determination of 1–500 μg V l^-1 in urine. The coefficient of variation for triplicate urine measurements is <8% for 10 μg V l^-1.     

Direct measurement of iron in serum by electrothermal atomic absorption spectrometry

A simple and rapid method is described for the determination of iron in serum by atomic absorption spectrometry with a graphite furnace atomiser. The serum is diluted 40 times with water, and injected into the graphite tube. Optimal conditions are established, and interferences from proteins and salts eliminated. Since the procedure requires no sample pretreatment such as protein precipitation or wet digestion, contamination and losses by co-precipitation are excluded. The method can determine any species of iron in serum.     

Determination of gallium in biological materials by electrothermal atomic absorption spectrometry

In this determination of gallium, the condition of the graphite tubes influences the peak height. Common acids and salts seriously affect the results, but in the presence of EDTA, interferences of nitric and hydrochloric acids are suppressed completely, and interferences of phosphoric acid and some salts are suppressed partly. To compensate for the effects, a standard addition procedure is proposed, and is applied to healthy and tumor.bearing mice. A linear calibration is obtained for 0.12–12 ng Ga in 50-μl aliquots. The method is applied to tissues and body fluids with good recovery and precision.     

Determination of chromium in gallium arsenide by electrothermal atomic absorption spectrometry

The sample is decomposed with 50% (v/v) aqua regia and the diluted solution is injected into the graphite furnace. The temperature program developed minimizes non-specific background signals, so that correction is not required. For a 100-mg sample, the 3σ detection limit is 70 ng Cr g^?1. The relative standard deviation of the overall procedure is 5–7%.     

Determination of aluminium and manganese in human scalp hair by electrothermal atomic absorption spectrometry using slurry sampling

Methods for the determination of aluminium and manganese in human scalp hair samples by electrothermal atomic absorption spectrometry using the slurry sampling technique were developed. Palladium and magnesium nitrate were used as chemical modifiers. Hair samples were pulverized using a zirconia vibrational mill ball, and were prepared as aqueous slurries. Determinations can be performed in the linear ranges of 1.9–150 μg l⁻¹ Al³⁺ and 0.03–10.0 μg l⁻¹ Mn²⁺. Limits of detection of 0.9 mg kg⁻¹ and 27.6 μg kg⁻¹ were obtained for aluminium and manganese, respectively. The analytical recoveries were between 99.6 and 101.8% for aluminium and in the 98.3–101.3% range for manganese. The repeatability of the methods (n=11), slurry preparation procedure and ETAAS measurement, was 16.0 and 7.9% for aluminium and manganese, respectively. The methods were finally applied to the aluminium and manganese determination in 25 scalp hair samples from healthy adults. The levels for aluminium were between 8.21 and 74.08 mg kg⁻¹, while concentrations between 0.03 and 1.20 mg kg⁻¹ were found for manganese.     

Determination of thallium in natural waters by electrothermal atomic absorption spectrometry

Thallium is determined in natural waters by electrothermal atomic absorption Spectrometry after preconcentration. Thallium is oxidized and retained as the tetrachlorothallate (III) ion on an anion exchange column, followed by elution with ammonium sulfite solution. A concentration factor of 400 is achieved. The detection limit of the method is 3.3 ng/1.     

Determination of arsenic in biological fluids by electrothermal atomic absorption spectrometry

A procedure for the determination of the total content of arsenic in urine, serum and blood by electrothermal atomic absorption spectrometry (ETAAS) is described. Zeeman correction is used to compensate the high background signals. The samples are diluted (1 + 1 for urine and 1 + 3 for both serum and blood samples) in a medium containing 0.1% w/v Triton X-100 before being introduced directly into the furnace. A solution containing 15% w/v hydrogen peroxide, 0.65% w/v nitric acid and 0.5% w/v nickel is also introduced into the atomizer by means of a separate injection. Calibration is carried out against aqueous standards for blood and serum samples and using the standard additions method for urine samples. The detection limit is 20 pg (2 ng ml-1). The reliability of the procedure is checked by analyzing three certified reference materials and by recovery studies.     

Determination of selenium in blood plasma and serum by flow injection hydride generation atomic absorption spectrometry

A flow injection hydride generation atomic absorption spectrometric (AAS) method has been used to determine the selenium concentrations of human serum and plasma samples following digestion with nitric, sulphuric and perchloric acids. In the hydride generation process, reduction was carried out by sodium tetrahydroborate to produce a hydride that was atomized in a flame-heated atomisation cell. The method had a detection limit of 1.2 ng ml-1 and a sensitivity of 2.1 ng ml-1. Within-run precisions of 5.8% at 20 ng ml-1 and 4.5% at 80 ng ml-1, and between-run precisions of 4.8% at 69 ng ml-1 and 3.4% at 80 ng ml-1 were obtained. An inter-laboratory comparison study with a graphite furnace AAS method was carried out and the results showed excellent agreement. The flow injection method of sample introduction allowed the use of a sample volume of 330 microliters with an injection rate of 90 injections per hour.