Determination of uranium by adsorptive stripping voltammetry at a lead film electrode

An adsorptive stripping voltammetric procedure for the determination of U(VI) at an in situ plated lead film electrode is described. The U(VI) complex with cupferron was accumulated from an acetate buffer solution of pH 4.2 at the potential −0.65 V. The measurements were carried out from undeaerated solutions. The calibration graph for an accumulation time of 180 s was linear from 5 × 10⁻¹⁰ to 2 × 10⁻⁸ mol L⁻¹. The detection limit was 2 × 10⁻¹⁰ mol L⁻¹, the relative standard deviation for 2 × 10⁻⁸ mol L⁻¹ U(VI) was 4.3%. The proposed procedure was validated in the course of U(VI) determination in water certified reference materials.     

Stripping voltammetry with collection at a rotating ring-disk electrode

A new electroanalytical technique is described, called "stripping voltammetry with collection." The technique involves the use of a rotating ring-disk electrode and is an improvement over traditional voltammetric stripping at a single electrode in that it is characterized by a lower limit of detection and that the period of deposition before stripping can be shorter. The use of the technique is illustrated by the determination of 10(-10)M Ag(+) in 0.1 M H(2)SO(4) by use of a ring-disk electrode having a disk electrode constructed of glassy carbon and a ring electrode constructed of platinum.     

Determination of selenium(IV) by cathodic stripping voltammetry using a copper-modified mercury-film electrode modified with copper

The behavior of selenium(IV) at a mercury-film electrode previously modified with copper was studied by cathodic stripping voltammetry using an automatic system for replacing solutions without opening the circuit. The effect of chemical (the composition and concentration of the supporting electrolyte, the concentrations of mercury (II) and copper(II)) and electrochemical parameters (the potential and time of electrolysis) on the analytical signal of selenium was studied at each stage of the stripping cycle (the formation of the mercury-film electrode modified with copper, the electrochemical preconcentration of selenium, and the subsequent stripping of the concentrate). The detection limit for selenium(IV) was found to be 40 ng/L (5.0 × 10^?10 M) at an electrolysis time of 10 min.     

Determination of lead(II) in water-alcohol media by stripping voltammetry at a modified carbon-glass-ceramic electrode

Effects of the electrolysis potential, electrolysis time, and potential sweep rate on the parameters of analytical signals of Pb(II) in water-alcohol media were studied. Calibration plots were constructed, and a procedure was proposed for the preparation of a carbon-glass-ceramic electrode surface. The procedure was based on electrochemical and chemical modification of the surface and provided reproducible results.     

Determination of Rh(III) by stripping voltammetry on a graphite electrode modified with lead

Journal of Solid State Electrochemistry - The process of electrooxidation of a lead-rhodium binary deposit on a graphite electrode has been studied. The anodic voltammetric curves show the peak of...     

Anodic stripping voltammetry and chronopotentiometry of copper at a rotating carbosital disk electrode

The use of a new carbon material — carbosital — for electrodes is reviewed. The behaviour of copper deposited on the carbosital electrode surface in anodic stripping voltammetry and chronopotentiometry is discussed. In anodic stripping voltammetry with a rotating carbosital disk electrode, the peak current and the number of coulombs involved in stripping copper are directly proportional to the square root of the electrode rotation rate during preelectroiysis; the peak current is directly proportional to the potential scan rate during stripping. For anodic stripping voltammetry and anodic stripping chronopotentiometry, linear calibration graphs are obtained in the range 1 X 10^-3–1 x 10^-6 M copper(II). The method is applicable to analysis of high-purity cadmium for copper.     

Determination of pseudouridine at submicromolar concentrations by cathodic stripping voltammetry at a mercury electrode

Pseudouridine (5-ribosyluracil), uridine (N,1-ribosyluracil), deoxyuridine (N,1-deoxyribosyluracil) and uracil are investigated by means of d.c. polarography and by differential and normal pulse polarography. Pseudouridine, which is known to be a cancer marker, yields anodic polarographic currents in the pH range 7–11, whereas uridine and deoxyuridine are inactive under the same conditions. The polarographic response of pseudouridine obtained is due to the formation of a sparingly soluble mercury compound. Pseudouridine can be determined by differential pulse polarography in the concentration range 2–6 × 10^?6 M and by differential-pulse cathodic stripping voltammetry at concentrations two orders of magnitude lower. Small excesses of uridine, deoxyuridine or proteins do not interfere with the determination.     

Simultaneous determination of tin and lead by a.c. anodic stripping voltammetry at a hanging mercury drop electrode sensitized by cetyltrimethylammoniu

The influence of cetyltrimethylammonium bromide (CTAB) on the simultaneous determination of tin(IV) and lead(II) by anodic stripping voltammetry at a hanging mercury drop electrode (HMDE) in a 0.1 M hydrochloric acid—0.1 M oxalic acid medium was studied using d.c. and a.c. stripping. In the presence of CTAB, tin and lead show voltammetric peaks separated by 100 mV, the sensitivity depending on the concentration of CTAB. The best conditions for the simultaneous determination of both elements (2 × 10^-3 M) were found. A method is proposed for the determination of tin in the presence of lead and three procedures are given for the determination of lead in the presence of tin.     

Determination of arsenic by cathodic stripping voltammetry at a hanging mercury drop electrode

Arsenic (III), respectively arsenic(V) after the reduction were determined in model solutions and some inorganic and organic materials by fast scan differential pulse cathodic stripping voltammetry and by direct current cathodic stripping voltammetry with a rapid increase of potential. The accumulation on a hanging mercury drop electrode followed by cathodic stripping was carried out in 0.7–0.8M HCl or 1–2M H₂SO₄ solutions containing Cu(II)-ions. Detection limits calculated from regression parameters was determined to be under 1 ng/ml for the samples containing very low arsenic concentrations. The relative standard deviation did not reach 8% for arsenic contents about of 5 ng/ml.     

TZAAP-Nafion修饰电极溶出伏安法测定痕量铜

近年来,化学修饰电极以其独特的优越性,在分析测试中具有广阔的应用前景[1-6],因此对于新的修饰剂的研究,以及用修饰电极探讨灵敏度高,选择性好的测定方法具有重要的意义。2[2,3,5-三氮唑偶氮]-5-乙酰基氨基苯酚(2-(2,3,5-triazolylazo)-5-acetam idophenol,简称TZAAP)是一种新合成的有机化合物,其结构式为:由于TZAAP可以和金属离子形成稳定的配合物,在光谱法中可以作为显色剂用于环境及生物样品中微量元素的测定[7,8]。Nafion是一种优良的阳离子交换剂,用作电极修饰材料具有良好的离子交换特性[9]。本文作者制备了TZAAP-Nafion修饰…     

Determination of thallium in the presence of large excess of lead by anodic stripping voltammetry

The paper is concerned with the determination of traces of thallium, as T1(I), in the presence of very large amounts of lead, by d.c. anodic stripping voltammetry, by adding both a complexing agent and anionic surfactant. The supporting complexing agent was 0.1M solution of EDTA (pH 4.4). The influence of the several surfactants on the signals of lead and thallium was investigated.In 0.1M EDTA at pH 4.4 at the absence of a surfactant, lead does not interfere at concentrations below 10^–4 M. When the electrolyte contains also an anionic surfactant, lead can be tolerated at concentrations up to 2 × 10^–3–6 × 10^–3 M (depending on the type of the surfactant), and the height of the thallium peak remains unaffected. This makes the determination of 10^–8 M T1(I) possible when the molar excess of lead is 2–6 × 10⁵ fold. The method has been tested by determining the thallium content of soil extracts.     

Determination of lead and cadmium using a polycyclodextrin-modified carbon paste electrode with anodic stripping voltammetry

This work reports the use of and -cyclodextrin-modified carbon paste electrodes (CPE_-CD and CPE_-CD) to determine simultaneously Pb(II) and Cd(II) by means of the electrochemical technique known as anodic stripping voltammetry (ASV). Both modified electrodes displayed good resolution of the oxidation peaks of the said metals. Statistic analysis of the results strongly suggests that the CPE_-CD exhibited a better analytical response that the CPE_-CD, while the detection limits obtained for Pb(II) were 6.3×10^–7 M for the CPE_-CD and 7.14×10^–7 M for the CPE_-CD, whereas for Cd(II) they were 2.51×10^–6 M for the CPE_-CD and 2.03×10^–6 M for the CPE_-CD.     

Trace analysis of lead by anodic stripping voltammetry with collection at interdigitated microelectrodes in small-volume samples

A simple and sensitive electroanalytical method was developed for microvolume trace elements determination. Commercially available interdigitated microelectrodes (IDA) from ALS Japan Inc. based on a thin carbon film technology were used. Anodic stripping voltammetry with collection at IDA was applied. Carbon IDA microbands were coated with a pre-deposited mercury film for better performance. The method with this sensor enables analysis of some heavy metals in total sample volumes as small as 0.05 cm³. The method was applied to Pb in blood samples determination by a standard addition method.     

An adsorptive stripping voltammetry of nickel and cobalt at a solid lead electrode

For the first time, a solid lead electrode (PbE) was exploited for adsorptive stripping voltammetric determination of Ni(II) and Co(II) in the presence of nioxime as a complexing agent. The calibration graphs for Ni(II) and Co(II) were linear from 0.059 to 0.59 µg L^?1 and from 0.029 to 0.29 µg L^?1 (accumulation time 120 s), respectively. The analytical parameters such as the detection limit and separation of analytical signals obtained at the solid lead electrode were comparable with those obtained using a lead film electrode while better in comparison to those reported before for the bismuth film or solid bismuth electrodes. Co(II) could be determined in the presence of a large excess of Ni(II) and Zn(II). The proposed electrode was applied to determine Co(II) and Ni(II) traces in certified reference material and a natural water sample with satisfactory results.     

Determination of dissolved sulphides in waste water samples by flow-through stripping chronopotentiometry with a macroporous mercury-film electrode

Sulphides in water samples were determined by stripping chronopotentiometry in a computer controlled flow system with a flow-through electrochemical cell. The working electrode was a porous glassy carbon electrode coated with Nafion and mercury. The sample was diluted with 0.1 mol L⁻¹ NaOH and analysed. Sulphides in the sample were collected in the porous electrode as mercury sulphide and then stripped by a current of −500 μA. The limit of detection was found to be 1.6 μg L⁻¹ and 0.5 μg L⁻¹ for 1 mL and 5 mL of preconcentrated sample, respectively. The linear range for 1 mL sample was found to be 5-400 μg L⁻¹. The repeatability and reproducibility was found to be 2.6% and 4.8%, respectively. The method was applied to analyses of waste water samples from a tannery.     

Evaluation of differential pulse anodic-stripping voltammetry at a stationary mercury-film electrode with stirred solution

Differential pulse anodic-stripping voltammetry at a stationary mercury-film electrode with the solution stirred during the deposition step has been investigated. The sensitivity achieved by using such a simple set-up is similar to that obtained with a mercury-film rotating disk electrode. The effects of various experimental parameters on the peak current are described. Lead and cadmium were used as test systems, and gave detection limits of around 1 x 10(-10)M with 5-min deposition times.     

Determination of trace aluminium by adsorptive stripping voltammetry on a preplated bismuth-film electrode in the presence of cupferron

This work reports the use of adsorptive stripping voltammetry (AdSV) for the determination of aluminium on a rotating-disc bismuth-film electrode (BiFE). Al(III) ions in the non-deoxygenated sample were complexed with cupferron and the complex was accumulated by adsorption on the surface of the preplated BiFE. The stripping step was carried out by using a square-wave (SW) potential-time voltammetric excitation signal. The experimental variables as well as potential interferences were investigated and the figures of merit of the method were established. Using the selected conditions, the 3σ limit of detection for aluminium was 0.5 μg l⁻¹ at a preconcentration time of 240 s and the relative standard deviation was 4.2% at the 5 μg 1⁻¹ level for a preconcentration time of 120 s (n = 8). The accuracy of the method was established by analysing water and metallurgical samples.     

Determination of medecamycin by adsorptive stripping voltammetry with an activated electrode

The adsorptive and electrochemical behaviors of medecamycin were investigated on a glassy carbon electrode (GCE) pretreated by anodic oxidation at +1.8 V for 5 min in 0.025 mol l^–1 NH₃-NH₄Cl (pH 8.6) solution. An adsorptive stripping voltammetric method for the determination of medecamycin at the pretreated glassy carbon electrode has been developed. Medecamycin was accumulated in NH₃-NH₄Cl buffer (pH 9.0) at a potential of –0.7 V (vs. saturated calomel electrode (SCE)) for a certain time, and then determined by second-order differential anodic stripping voltammetry. The second-order differential anodic stripping peak current at +0.72 V was proportional to the concentration of medecamycin in the range 2.0 g ml^–1 to 50.0 g ml^–1. The detection limit (three times the signal-to-noise) was 1.0 g ml^–1 and the relative standard deviation of the results was 3.28% for eight successive determinations of 10.0 g ml^–1 medecamycin. This method has been applied to the direct determination of medecamycin in commercial tablets and spiked urine samples with satisfactory results.