Relationship between surface anchoring strength and surface ordering on weakly rubbed polyimide surfaces

We have investigated the relationship between the polar anchoring strength and surface ordering in a nematic liquid crystal on two kinds of weakly rubbed polyimide (PI) surfaces. The polar anchoring strength of 5CB on weakly rubbed PI surfaces, both with and without side chains, increases with rubbing strength and with decreasing temperature. The surface order parameter of 5CB on these surfaces increases with rubbing strength, suggesting that the polar anchoring strength on rubbed PI surfaces is related to the surface order parameter.     

Washing effects on the anchoring energy and surface order parameter on rubbed polymer surfaces containing the trifluoromethyl moiety

The washing effects on liquid crystal (LC) alignment capability in a NLC, 4-n-pentyl-4'-cyanobiphenyl (5CB), on a rubbed polyimide (PI) surface containing the trifluoromethyl moiety were studied. The extrapolation length d_e of 5CB on the rubbed PI surface decreases with the rubbing strength RS. Also, the large extrapolation length d_e of 5CB for washing with IPA was measured at RS=114 mm. The polar anchoring energy of 5CB on the rubbed PI surface was decreased by the washing process; it increased with the rubbing strength RS on the PI surface. The surface order parameter S_S of 5CB for all the washing processes is smaller than for the non-washing process. Consequently, the polar anchoring energy and surface order parameter S_s in 5CB are largely attributed to washing effects.     

Influence of the washing process on the aligning capability of a nematic liquid crystal on polymer surfaces

The influence of washing processes on the liquid crystal (LC) aligning capability on rubbed polyimide (PI) surfaces containing the CONH moiety were investigated. The induced optical retardation from a non-washing process on a rubbed PI surface is larger than when the washing processes are included. The pretilt angles in 4-n-pentyl-4'-cyanobiphenyl (5CB) were decreased by the washing process. The polar anchoring energy of 5CB was decreased by the washing processes on a weakly rubbed PI surface. The surface order parameter S_S of 5CB strongly depends on the rubbing strength and washing materials. Consequently, the LC aligning capability may be strongly attributed to the polymer characteristics and the washing processes.     

Liquid crystal alignment capabilities on rubbed organic solvent soluble polyimide surfaces with trifluoromethyl moieties

High pretilt angles, polar anchoring energy (out of plane-tilt), and surface ordering in the nematic liquid crystal 4-n-pentyl-4'-cyanobiphenyl (5CB) were investigated on rubbed organic solvent soluble polyimide (PI) surfaces with a helical backbone structure and trifluoromethyl moieties. It was found that the pretilt angle of 5CB is about 15° in the wide rubbing region of rubbed soluble PI surfaces with trifluoromethyl moieties attached to the lateral benzene rings. It is suggested that the microscopic surface structure of the polymer contributes to the LC pretilt angle generation at the surface. Also, the polar anchoring energy of 5CB is dependent on the molecular structure of these unidirectionally rubbed soluble PI surfaces. The polar anchoring strength of 5CB on rubbed soluble PI surfaces is as weak with trifluoromethyl moieties attached to the lateral benzene rings weak as when the trifluoromethyl moieties are attached to the polymer backbone. Finally, the polar anchoring energy of 5CB strongly depends on the surface ordering of rubbed soluble PI surfaces.     

Liquid crystal alignment capabilities on rubbed organic solvent soluble polyimide surfaces with trifluoromethyl moieties

High pretilt angles, polar anchoring energy (out of plane-tilt), and surface ordering in the nematic liquid crystal 4-n-pentyl-4'-cyanobiphenyl (5CB) were investigated on rubbed organic solvent soluble polyimide (PI) surfaces with a helical backbone structure and trifluoromethyl moieties. It was found that the pretilt angle of 5CB is about 15° in the wide rubbing region of rubbed soluble PI surfaces with trifluoromethyl moieties attached to the lateral benzene rings. It is suggested that the microscopic surface structure of the polymer contributes to the LC pretilt angle generation at the surface. Also, the polar anchoring energy of 5CB is dependent on the molecular structure of these unidirectionally rubbed soluble PI surfaces. The polar anchoring strength of 5CB on rubbed soluble PI surfaces is as weak with trifluoromethyl moieties attached to the lateral benzene rings weak as when the trifluoromethyl moieties are attached to the polymer backbone. Finally, the polar anchoring energy of 5CB strongly depends on the surface ordering of rubbed soluble PI surfaces.     

Effect of pretilt angle on the polar anchoring energy in NLCs on weakly rubbed polyimide surfaces

The polar anchoring strength and pretilt angle generation in nematic liquid crystals (NLCs), on three kinds of rubbed polyimide (PI) surfaces, were investigated. The pretilt angle generated in 4-n-pentyl-4'-cyanobiphenyl (5CB) is large compared with ZLI-4792 (a fluorinated mixture type NLC) for all rubbed PI surfaces. The high pretilt angle in 5CB is attributed to a much larger birefringence and much larger perpendicular component of permittivity. The polar anchoring energy of ZLI-4792 is high compared with 5CB on all rubbed PI surfaces for a weak rubbing strength. It is suggested that the high anchoring energy of ZLI-4792 may be attributed to the low NLC pretilt angle.     

Investigation of surface anchoring strength and pretilt angle in NLC on rubbed polythiophene surfaces with alkyl chain lengths

A high pretilt angle for the nematic liquid crystal, 4-n-pentyl-4'-cyanobiphenyl (5CB), was observed on rubbed polythiophene (PTP) surfaces having alkyl chains with more than ten carbon atoms. We consider that this is due to a surface-excluded volume effect caused by the long alkyl chains between the LC molecules and the PTP surfaces. The polar anchoring strength in 5CB on rubbed PTP surfaces with long alkyl chains has also been successfully evaluated. The extrapolation length d_e of 5CB increases with increasing alkyl chain lengths above the seven carbons of alkyl chain R7; that is, it may be attributed to the high pretilt angle. An extrapolation length of 5 nm is observed in 5CB for the seven carbons alkyl chain R7 on the PTP surface; this indicates high anchoring strength.     

Preliminary Communication : Generation of high pretilt angles of nematic liquid crystal (5CB) on rubbed organic solvent soluble polyimide surfaces with helical backbone structure and trifluoromethyl moieties

High pretilt angles of nematic liquid crystals (NLC) have been successfully generated on rubbed organic solvent soluble polyimide (PI) surfaces with a helical backbone structure and trifluoromethyl moieties. We have found that the pretilt angle of in 4-n-penty-4-cyanobiphenyl (5CB) on rubbed PI surfaces with trifluoromethyl moieties attached to the lateral benzene rings is larger compared to that on rubbed PI surfaces with trifluoromethyl moieties attached to the polymer backbone. The observed pretilt angle of 5CB on unidirectionally rubbed PI surfaces with trifluoromethyl moieties attached to the lateral benzene rings is about 15 degrees in the wide rubbing region. From these results, it is expected that the microscopic surface structure of the polymer strongly contributes to the pretilt angle generation of the LCs at the surface.     

Surface morphology at nanometer level and optical phase retardation of rubbed alignment films

The surface morphology of rubbed polyimide LC aligning films has been studied by scanning force microscopy. We examined three types of alignment film: HT-210, AL-1051 (main chain type) and AL-8044 (side chain type) polyimide surfaces. The rubbed polyimide surfaces show anisotropic alignment of the polymer chain cluster, and a microgroove between the ripple pattern streaks. Also, they are periodically oriented along the rubbing direction. The optical phase retardation of the rubbed surface does not increase with increased cumulative time of rubbing, On the other hand, it increases monotonically with increasing rubbing depth.     

Surface morphology at nanometer level and optical phase retardation of rubbed alignment films

The surface morphology of rubbed polyimide LC aligning films has been studied by scanning force microscopy. We examined three types of alignment film: HT-210, AL-1051 (main chain type) and AL-8044 (side chain type) polyimide surfaces. The rubbed polyimide surfaces show anisotropic alignment of the polymer chain cluster, and a microgroove between the ripple pattern streaks. Also, they are periodically oriented along the rubbing direction. The optical phase retardation of the rubbed surface does not increase with increased cumulative time of rubbing, On the other hand, it increases monotonically with increasing rubbing depth.     

Zigzag defect-free alignment of surface stabilized ferroelectric liquid crystal cells with a polyimide irradiated by polarized UV light

Zigzag defect-free surface stabilized ferroelectric liquid crystal (SSFLC) cells were prepared using a photodegradable polyimide (PI) having a cyclobutane ring in the backbone. The PI layers were irradiated by polarized ultraviolet light (PUVL) at normal incidence to the surface, and characterized by UV and FTIR spectroscopy. The anisotropy originates from preferential cleavage of PI chains oriented parallel to the polarization direction of the irradiating PUVL. After the polarized UV light irradiation, the PI surface was much flatter than that after rubbing, but it induced a similar order parameter of dye-doped nematic LC molecules to that for a rubbed cell. Alignment of both the FLC molecules and the layer structure is important in SSFLC. After 40 min irradiation, the FLC molecules were well aligned homogeneously, and the FLC cells showed a uniform texture without zigzag defects which also indicates a well aligned layer structure. Zigzag defect-free alignment may result from the flatter surface, the much smaller and more constant pretilt angles, and the bigger cone angle than those achieved by rubbing.     

Laser‐induced periodic surface structure on a polymer surface: The effect of a prerubbing treatment on the surface structure

The influence of the mechanical rubbing of a polyimide (PI) film on the laser‐induced periodic structure (LIPS) was demonstrated. The periodicity and amplitude of LIPS were greater when the rubbing direction was parallel to the laser polarization direction. The amplitude became small and the periodicity of LIPS did not show an obvious change when the rubbing direction was perpendicular to the laser polarization direction. The effect of the rubbing pretreatment on LIPS was explained on the basis of the wave‐guide effect of rubbing‐induced microgrooves on LIPS formation. The orientation of PI chains induced by mechanical rubbing was relaxed after laser irradiation, and a new orientation of PI chains was formed during the LIPS formation. When the rubbing direction was perpendicular to the laser polarization direction, the orientation of PI chains remained in the rubbing direction. The laser‐irradiated, perpendicularly rubbed PI surface could be used to verify the effects of surface morphologies and intermolecular interactions on liquid‐crystal alignment. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1273–1280, 2003     

Dynamic behaviour at a nematic liquid crystal-rubbednylon interface using evanescent wave photon correlation spectroscopy

Photon correlation spectroscopy of light scattered by director fluctuations from an evanescent optical wave propagating in the nematic liquid crystal 5CB is used to study the interfacial dynamic behaviour of the liquid crystal. The intensity correlation function of light scattered by interfacial orientation fluctuations is measured by illuminating to give a short optical penetration depth within the nematic. These surface scattering correlation functions strongly differ from the bulk correlation function and are interpreted in terms of a nematic surface orientation mode arising from the coupling between the director field and the fluid velocity. It is shown that the analysis of the surface mode gives a method for measuring anchoring energies in liquid crystals. The anchoring energy obtained for rotation of the director away from the rubbing direction about an axis normal to the surface for 5CB at a rubbed nylon surface is 7.14±0.7 × 10-² ergcm-².     

Zigzag defect-free alignment of surface stabilized ferroelectric liquid crystal cells with a polyimide irradiated by polarized UV light

Zigzag defect-free surface stabilized ferroelectric liquid crystal (SSFLC) cells were prepared using a photodegradable polyimide (PI) having a cyclobutane ring in the backbone. The PI layers were irradiated by polarized ultraviolet light (PUVL) at normal incidence to the surface, and characterized by UV and FTIR spectroscopy. The anisotropy originates from preferential cleavage of PI chains oriented parallel to the polarization direction of the irradiating PUVL. After the polarized UV light irradiation, the PI surface was much flatter than that after rubbing, but it induced a similar order parameter of dye-doped nematic LC molecules to that for a rubbed cell. Alignment of both the FLC molecules and the layer structure is important in SSFLC. After 40 min irradiation, the FLC molecules were well aligned homogeneously, and the FLC cells showed a uniform texture without zigzag defects which also indicates a well aligned layer structure. Zigzag defect-free alignment may result from the flatter surface, the much smaller and more constant pretilt angles, and the bigger cone angle than those achieved by rubbing.     

Novel alignment method for control of high pretilt angle by using a solvent dipping effect on polymer surfaces

A novel alignment method for control of high pretilt angle in nematic liquid crystals (NLC), using a solvent dipping effect on various alignment layers, was successfully investigated. The pretilt angle of a NLC is increased by dipping before rubbing treatment on three kinds of rubbed polyimide (PI) surfaces. The pretilt generated by the dipping after rubbing a PI surface with a short side chain is high compared with a PI surface with a long side chain. The pretilt generated by dipping before rubbing homeotropic layer of a positive type NLC (δε > 0) is lower than that of the negative type NLC (δε < 0). The generated NLC pretilt angle is attributed to the perpendicular component of the permittivity epsilon of the NLC.     

Rubbing-induced molecular reorientation on an alignment surface of an aromatic polyimide containing cyanobiphenyl side chains

Surface lamellar decoration (SLD), surface enhanced Raman scattering (SERS) and optical second harmonic generation (SHG) experiments have been utilized to study the molecular orientation and conformation changes at a rubbed polyimide alignment-layer surface. This aromatic polyimide containing pendent cyanobiphenyl mesogens was synthesized via a polycondensation of 2,2'-bis(3,4-dicarboxy-phenyl)hexafluoropropane dianhydride (6FDA) with bis[omega-[4-(4-cyanophenyl)phenoxy]hexyl] 4,4'-diamino-2,2'-biphenyldicarboxylate (nCBBP, n = 6), abbreviated as 6FDA--6CBBP. Uniform alignment layers, possessing high pretilt angles ranging from 39 degrees to 43 degrees, have been achieved after mechanical rubbing of the polyimide thin film surface at room temperature and subsequent annealing. This is the first time that high pretilt angles have been detected to possess a negative angle (-theta(c)) with respect to the rubbing direction (i.e., opposite to the rubbing direction), considerably different from the conventional pretilt angle (theta(c)) observed along the rubbing direction. This observation is confirmed using magnetic null and SHG methods. Combined polyethylene (PE) SLD and atomic force microscopy experiments reveal that the azimuthal orientation distribution of the long axis of the edge-on PE lamellar crystals is oriented normal to the rubbing direction, indicating that the PE chains are aligned parallel to the rubbing direction. This SLD technique probes the anisotropic surface orientation of the outermost molecules of the rubbed polyimide layer. The SERS results show that prior to rubbing the surface, both the pendent cyanobiphenyls in the side chains and backbones possess nearly planar chain conformations at the polyimide surface. Mechanical rubbing causes not only tilting of the backbone moieties, such as imide-phenylene structure, but also significant conformational rearrangements of the pendent side chains at the surfaces. The molecular mechanism of this unusual alignment is due to the fact that the pendent cyanobiphenyls forms a uniformly tilted conformation on the rubbed surface, and the polar cyano groups point down toward the layer surface deduced from SHG phase measurements. This conformational rearrangement of the side chains results in the formation of fold-like bent structures on the surface, which directly leads to the long axis of cyanobiphenyls having the -theta(c) pretilt angle with respect to the rubbing direction.     

Cell processing on polyimide surface patterned by rubbing

In this study, we prepared a novel rubbed fluorinated polyimide film using a rubbing machine with a rubbing cloth and determined the surface properties of the rubbed film using an atomic force microscope and contact angle measurements. In addition, we evaluated the cell adhesion behavior on the rubbed polyimide film using a phase contrast microscope. Interestingly, a rubbed polyimide surface having a micrometer‐scale grooved pattern was prepared by the rubbing method, and the morphologies of rat primary hepatocytes and human liver cell lines attached to the rubbed surface were three‐dimensional multicellular spheroids, while the cells on an unrubbed surface showed two‐dimensional monolayers. This initial study indicates that the rubbing method without any chemical modification is simple and can easily produce large surface areas, suggesting that the rubbing may become a novel cell culture method. Copyright © 2008 John Wiley & Sons, Ltd.     

Molecular orientation and alignment of rubbed poly(vinyl cinnamate) surfaces

We observed that weakly and strongly rubbed polyvinyl-cinnamate surfaces align liquid crystal films perpendicular and parallel to the rubbing direction, respectively. Surface-specific sum-frequency vibrational spectroscopy was used to probe molecular orientations and alignments of the rubbed surfaces and provide a molecular-level understanding of the observation.     

Polar and azimuthal alignment of a nematic liquid crystal by alkylsilane self-assembled monolayers: effects of chain-length and mechanical rubbing

Alkylsilane self-assembled monolayers (SAMs) on oxide substrates are commonly used as liquid crystal (LC) alignment layers. We have studied the effects of alkyl chain length, photolytic degradation, and mechanical rubbing on polar and azimuthal LC anchoring. Both gradient surfaces (fabricated using photolytic degradation of C18 SAMs) and unirradiated SAMs composed of short alkyl chains show abrupt transitions from homeotropic to tilted alignment as a function of degradation or chain length. In both cases, the transition from homeotropic to tilted anchoring corresponds to increasing wettability of the SAM surfaces. However, there is an offset in the critical contact angle for the transition on gradient vs unirradiated SAMs, suggesting that layer thickness is more relevant than wettability for LC alignment. Mechanical rubbing can induce azimuthal alignment along the rubbing direction for alignment layers sufficiently near the homeotropic-to-planar transition. Notably, mechanical rubbing causes a small but significant shift in the homeotropic-to-tilted transition, e.g., unrubbed C5 SAMs induce homeotropic anchoring, but the same surface after rubbing induces LC pretilt.