Simultaneous spectrophotometric determination of phosphate and silicate ions in river water by using ion-exclusion chromatographic separation and post-column derivatization

The simultaneous spectrophotometric determination of phosphate and silicate ions in river water was examined by using ion-exclusion chromatography and post-column derivatization. Phosphate and silicate ions were separated by the ion-exclusion column packed with a polymethacrylate-based weakly acidic cation-exchange resin in the H⁺-form (TSKgel Super IC-A/C) by using ultra pure water as an eluent. After the post-column derivatization with molybdate and ascorbic acid, so-called molybdenum-blue, both ions were determined simultaneously by spectrophotometry. The effects of sulfuric acid, sodium molybdate and ascorbic acid concentrations and reaction coil length, which have relation to form the reduced complexes of molybdate and ions, on the detector response for phosphate and silicate ions were investigated. Under the optimized conditions (color-forming reactant, 50 mM sulfuric acid-10 mM sodium molybdate; reducing agent, 50 mM ascorbic acid; reaction coil length, 6 m), the calibration curves of phosphate and silicate ions were linear in the range of 50-2000 μg L⁻¹ as P and 250-10,000 μg L⁻¹ as Si. This method was successfully applied to water quality monitoring of Kurose-river watershed and it suggested that the effluent from a biological sewage treatment plant was significant source of phosphate ion in Kurose-river water.     

Isotope exchange of strontium and molybdate ions in strontium polymolybdates

The heterogeneous isotopic exchange reactions in strontium polymolybdates of Sr²⁺ and MoO₄ ^2- ions in the strontium nitrate and sodium molybdate solutions have been studied using ⁹⁰Sr and ⁹⁹Mo as tracers. Electrometric methods have been used to study the compositions of strontium molybdates obtained by adding strontium chloride to a progressively acidified solution of sodium molybdate. It has been found that the exchange fraction increases with increasing chain length of strontium polymolybdate. The exchange equilibrium constant (K _ex) has been calculated between 298 and 348 K as well as DG°, DH° and DS°. The results indicate that Sr²⁺ cations have a much higher affinity for exchangers than MoO₄ ^2- anions. By fitting the data to the Dubinin-Radushkevich (D-R) isotherm it has been shown that the exchange capacity (X _m ) for both ions is affected by the ion adsorption process at low temperatures and by the ion exchange process at high temperatures. At high concentrations, the recrystallization process contributes to on the cation exchange but is ineffective on the anion exchange mechanism.     

pH-Responsive Nanocomposites From Methylcellulose and Attapulgite Nanorods: Synthesis,Swelling and Absorption Performance on Heavy Metal Ions

A pH-responsive methylcellulose-g-poly(sodium acrylate)/attapulgite (MC-g-PNaA/APT) nanocomposite superabsorbent was prepared by the free-radical solution polymerization of methylcellulose (MC), sodium acrylate (NaA) and nanoscale attapulgite (APT) in the presence of the crosslinker N,N′-methylene-bis-acrylamide (MBA). The structure and morphology of the nanocomposite were characterized by FTIR, FESEM, TEM, XRD and EDS techniques, and the effects of the amount of MBA, MC and APT nanorods on swelling behaviors were also evaluated. Results indicate that NaA has been grafted onto MC macromolecular chains and APT nanorods participated in polymerization by its active silanol groups, and APT led to a better dispersion in the MC-g-PNaA matrix. The incorporation of APT clearly enhanced the swelling capacity and rate of the superabsorbent. In addition, the nanocomposite exhibited excellent absorption capacity on heavy metal ions, and its absorption amounts on Ni²⁺, Cu²⁺ and Zn²⁺ ions reached 9.86, 7.66 and 21.86 times greater than active carbon (AC). The biopolymer-based nanocomposite superabsorbents can be used as a potential water-saving material and candidate of AC for heavy metal ion absorption.     

Vinyl polymerization. 403. Polymerization of vinyl monomer initiated with sodium poly-p-vinylphenolate

The polymerization of vinyl monomer initiated by poly-p-vinylphenol (PVPh) in NaOH aqueous solution was carried out at 85°C with shaking. Methyl methacrylate (MMA) was polymerized, whereas styrene and acrylonitrile were not. PVPh, which is dissociated into phenolate form (PVPh^?Na⁺) in NaOH aqueous solution, was effective for the polymerization. The effects of the amounts of MMA, PVPh, NaOH, and H₂O on the conversion of MMA were studied. The rate of polymerization of MMA increased with an increase in the molecular weight of PVPh-Na. The overall activation energy was estimated as 54 kJ mol^?1. The polymerization proceeded through a radical mechanism. The addition of tetra-n-butylammonium bromide increased the rate of polymerization.     

Aqueous polymerization of acrylonitrile by ascorbic acid–peroxodisulfate redox system

The polymerization of acrylonitrile initiated by an ascorbic acid–peroxodisulfate redox system was studied in an aqueous solution at 35°C in the presence of air. Molecular oxygen was found to have no effect on the polymerization reaction. An increase in ionic strength slightly increased the rate. The overall rate of polymerization, R_p, showed a square dependence on [monomer] and a half-order dependence on [peroxodisulfate]. A first-order dependence on [ascorbic acid] at low concentrations (<3.0 × 10^?3 mol L^?1) followed by a decrease in R_p at higher concentrations of ascorbic acid (>3.0 × 10^?3 mol L^?1) was also noted. R_p remained unchanged up to 40°C and showed a decline thereafter. Addition of catalytic amounts of cupric ions decreased the rate whereas ferric ions were found to increase the rate. Added sulfuric acid in the range (6.0?50.0) × 10^?5 mol L^?1 decreased the R_p.     

Ion-Selective Electrodes Based on Adamantylcalix[4,8]arenes for the Determination of Alkali Cations

Calix[4,8]arenes bearing adamantyl substituents in the upper rim and ethoxycarbonylmethoxy groups in the lower rim of the macrocycle were proposed as ionophores in membranes of ion-selective electrodes (ISEs) for determining alkali cations. Depending on the number of phenolic fragments (n) in the calixarene molecule, ISEs respond to either sodium (n = 4) or cesium (n = 8) ions. Sensors based on membranes that, along with ionophores, contain tetraphenyl borate ions as a lipophilic additive are selective for Na and Cs ions in the presence of other alkali metals. They exhibit almost theoretical responses over the concentration range from 1 × 10^–4 to 1 × 10^–1 M at pH 5.5–12 for Na-SE and pH 3–11 for Cs-SE, respectively.     

The electric transport of proton-bound water in MF-4SK/PAni nanocomposite membranes

Electrochemical characteristics of MF-4SK/PAni nanocomposite membranes prepared at different times of chemical polymerization of aniline are studied. Electroosmotic permeability and conductivity of membranes in solutions of acids and sodium chloride are determined. It is revealed that the conductivity of nanocomposites in the proton form at 30-day synthesis is approximately 3 times as low as that of the base membrane and composite membrane formed at 5-h synthesis. The transport number of water slightly depends on the structural type of membrane and changes from 3.3 to 2 mol H₂O/mol H⁺ with an increase in the concentration of HCl solution from 0.1 to 3 M. The ratio of transport number to the water content rises about twofold in composites as compared to the initial membrane. It is shown that water is transferred with proton as hydronium structures [H₅O₂]⁺ and [H₉O₄]⁺ by the migration mechanism whose contribution to the total proton transfer in composite membranes increases.     

P (VDF‐co‐CTFE)‐g‐P2VP amphiphilic graft copolymers: Synthesis,structure, and permeation properties

A series of amphiphilic graft copolymers of poly (vinylidene fluoride‐co‐chlorotrifluoroethylene)‐g‐poly(2‐vinyl pyridine), P (VDF‐co‐CTFE)‐g‐P2VP, with different degrees of P2VP grafting (from 26.3 to 45.6 wt%) was synthesized via one‐pot atom transfer radical polymerization (ATRP). The amphiphilic properties of P (VDF‐co‐CTFE)‐g‐P2VP graft copolymers allowed itself to self‐assemble into nanoscale structures. P (VDF‐co‐CTFE)‐g‐P2VP graft copolymers were introduced into neat P (VDF‐co‐CTFE) as additives to form blending membranes. When two different solvents, N‐methyl‐2‐pyrrolidone (NMP) and dimethylformamide (DMF), were used, specific organized crystalline structures were observed only in the NMP systems. P (VDF‐co‐CTFE)‐g‐P2VP played a pivotal role in controlling the morphology and pore structure of membranes. The water flux of the membranes increased from 57.2 to 310.1 L m^?2 h^?1 bar^?1 with an increase in the PVDF‐co‐CTFE‐g‐P2VP loading (from 0 to 30 wt%) due to increased porosity and hydrophilicity. The flux recovery ratio (FRR) increased from 67.03% to 87.18%, and the irreversible fouling (R_ir) decreased from 32.97% to 12.82%. Moreover, the pure gas permeance of the membranes with respect to N₂ was as high as 6.2 × 10⁴ GPU (1 GPU = 10^–6 cm³[STP]/[s cm² cmHg]), indicating their possible use as a porous polymer support for gas separation applications.     

Surface and internal modification of composite ion exchange membranes for removal of molybdate,phosphate, and nitrate from polluted groundwater

Al₂O₃/chitosan-multiwall carbon nanotubes (MWCNTs) were created to increase the exchange capacity of polyvinylidene fluoride (PVDF) ion-exchange membranes. The composite membranes were made by mixing Al₂O₃ nanoparticles into the PVDF cast solution, then applying a thin coating of chitosan functionalized carbon nano tubes (Cs-MWCNTs) to the PVDF membrane surface. The structure and characteristics of the hybrid membranes were described using XRD, SEM, IR, and TG-DTA. The Al₂O₃-PVDF/Cs-MWCNTs membrane beat the other Al₂O₃-PVDF/Cs, Al₂O₃-PVDF, and PVDF membranes in terms of molybdate, phosphate, and nitrate adsorption. The removal efficiency, pH solution, adsorption capacity, and desorption process of molybdate, phosphate, and nitrate anions by Al₂O₃-PVDF and PVDF membranes were investigated. The removal effectiveness of molybdate, phosphate, and nitrate, according to the testing findings, was 94.3, 65.6, and 85.78 %, respectively. The adsorption of MoO₄^2?, PO₄^3?, and NO₃^? increased as the pH increased initially until the best adsorption was achieved, and then decreased significantly as the pH increased further. The total adsorption capabilities of MoO₄^2?, PO₄^3?, and NO₃^?for the Al₂O₃-PVDF/Cs-MWCNTs membrane were 65.50, 61.22, and 59.77 mg/g, respectively. Using regeneration and reuse experiments for the simultaneous adsorption of molybdate, phosphate, and nitrate during three consecutive cycles, the adsorption/desorption of Al₂O₃-PVDF/Cs-MWCNTs was assessed. Al₂O₃-PVDF/Cs-MWCNTs offer a lot of promise when it comes to eliminating MoO₄^2?, PO₄^3?, and NO₃^?from actual wastewater samples.     

New Spectrophotmetric Methods for Determination of Cephapirine Na

Three sensitive and accurate spectrophotometric procedures were developed for the analysis of cephapirine sodium in pure form and in its pharmaceutical formulation. Method A: A kinetic method based on the observation that in acidic medium cephapirine reduces sodium molybdate to molybdenum blue, the absorbance of which is proportional to the amount of antibiotic present at a fixed time of 40 minutes; the formed product was spectrophotometrically measured at 780 nm. The concentration of drug calculated using its calibration by fixed concentration and rate constant methods is feasible with the calibration equations obtained, but the fixed time method proved to be more applicable. Method B is based on chetale formation with palladium(II) chloride in buffered medium as the interaction between metal ions and ligand anions or moleules capable of the formation of complexes which results in the development of colors suitable for the characterization of quantitative determination of metal or ligand. Metals containing easily excited d or f electrons were suitable for the formation of colored complexes. Method C, is based on the formation of colored complex between palladium(II), eosin and cephapirine Na. Sodium lauryl sulphate is used as surfactant to increase the solubility and intensity of the formed complex. Under optimum conditions, the complexes showed maximum absorption at Δ370 and Δ550 for methods B and C, respectively. Apparent molar absorpitivities were 5.2 × 10³, 5.5 × 10³, 1.4 × 10⁴; Sandell's sensitivities were 1.17 × 10^?3, 1.24 × 10^?3, 3.1 × 10^?3, for methods A, B and C, respectively. The solution of the products obeyed Beer's Law in the concentration ranges 10–70, 20–70, 2–48, μg mL^?1 for methods A, B, and C. The proposed methods were applied to the determination of the drug in pure or pharmaceutical preparations. The results obtained were compared statistically with those given by the official method.     

Formation of composite films of ion-track membranes embedded with oblique Cu nanowires for anisotropic infrared absorption

Composite films of poly(ethylene terephthalate) (PET) embedded with Cu nanowires were prepared by electroplating ion-track PET membranes. PET films were irradiated with 450 MeV ¹²⁹Xe²³⁺ ions with a direction of 45° from the film normal, and then etched with sodium hydroxide solution to form thin pores of 1 μm diameter. Cu was filled into the pores by electroplating in a copper sulfate solution to form Cu nanowires embedded in a direction tilted from the film normal. The composite membrane showed anisotropic infrared absorption in the in-plane direction, having the transmission axis in the direction normal to the ion incidence.     

Conductivity studies on modified laponites

Significant increase of the a.c. conductivity of Laponite is achieved when the sodium form is totally exchanged with potassium ions; however, the rheological properties alter, e.g. the clay will no longer form a gel with water. Exchange with Li⁺, Rb⁺, Cs⁺ or Cu²⁺ produces no increase in the a.c. conductivity over that of the sodium form. The synthesis of fluoro-laponites, with increased sodium contents, via a sol-gel method, gives materials of enhanced a.c. conductivity, which retain similar rheological properties to those of commercial Laponite. Some ²⁹Si and ⁶Li MAS NMR data are reported for the new materials.     

Preparation of PSSS‐grafted polysulfone microfiltration membrane and its rejection and removal properties towards heavy metal ions

3‐Hydroxy‐N,N‐diethylaniline (HDEA) as a tertiary aromatic amine was introduced onto the surface of chloromethylated polysulfone (CMPSF) microfiltration membrane through modification reaction, resulting in the modified membrane PSF‐DEA. A redox surface‐initiating system (DEA/APS) was constituted by the bonded tertiary aromatic amine group DEA and ammonium persulfate (APS) in aqueous solution, and so, the free radicals formed on the membrane initiated sodium p‐styrenesulfonate (SSS) as an anionic monomer to produce graft polymerization, getting the grafting‐type composite microfiltration membrane, PSF‐g‐PSSS membrane. Subsequently, the adsorption property of PSF‐g‐PSSS membrane for three heavy metal ions, Pb²⁺, Zn²⁺, and Hg²⁺ ions, was fully examined, and the rejection performance of PSF‐g‐PSSS membrane towards the three heavy metal ions was emphatically evaluated via permeation experiments. The experimental results show that by the initiating of the surface‐initiating system of DEA/APS, the graft polymerization can smoothly be carried out under mild conditions. PSF‐g‐PSSS membrane as a functional microfiltration membrane has strong adsorption ability for heavy metal ions by right of strong electrostatic interaction (or ion exchange action) between the anionic sulfonate ions on the membrane and heavy metal ions. The order of adsorption capacity is Pb²⁺ > Zn²⁺ > Hg²⁺, and the adsorption capacity of Pb²⁺ ion gets up to 2.18 μmol/cm². As the volume of permeation solutions, in which the concentrations of the three metal ions are 0.2 mmol/L, are in a range of 50 to 70 mL, the rejection rate of PSF‐g‐PSSS membrane for the three heavy metal ions can reach a level of 95%, displaying a fine rejection and removing performance towards heavy metal ions.     

Pore-functionalized polymer membranes for preconcentration of heavy metal ions

Functionalized membranes containing carboxylate, phosphate and sulfonate groups were prepared by UV-initiator induced graft polymerization of the functional monomer (acrylic acid, ethylene glycol methacrylate phosphate (EGMP) and 2-acrylamido-2-methyl-1-propane sulfonic acid) with a crosslinker (methylenebisacrylamide) in the pores of poly(propylene) host membranes. The functionalized membranes thus obtained were characterized by gravimetry, FTIR spectroscopy, radiotracers and scanning electron microscopy for the degree of grafting and water uptake, presence of functional groups, ion-exchange capacity, and physical structure of the membranes, respectively. The uptakes of Cs⁺, Ag⁺, Sr²⁺, Cd²⁺, Hg²⁺, Zn²⁺, Eu³⁺, Am³⁺, Hf⁴⁺ and Pu⁴⁺ ions in the functionalized membranes were studied as a function of acidity of the equilibrating aqueous solution. Among the functionalized membranes prepared in the present work, the EGMP-grafted membrane (with phosphate groups) showed acid concentration dependent selectivity towards multivalent metal ions like Eu³⁺, Am³⁺, Hf⁴⁺ and Pu⁴⁺. The solvent extraction studies of EGMP monomer in methyl isobutyl ketone (MIBK) solvent indicated that divalent and trivalent metal ions form complexes with EGMP in 1:2 proportion, but the distribution coefficients of trivalent metal ions were significantly higher that for the divalent ions. The uptakes of Eu³⁺ ions in monomeric EGMP (dissolved in MIBK) and polymeric EGMP (in the forms of crosslinked gel and membrane) were studied as a function of concentration of H⁺ ions in the equilibrating solution. This study indicated that polymeric EGMP has better binding ability towards Eu³⁺ as compared to monomeric EGMP. The variation of distribution coefficients of Eu³⁺/Am³⁺ in gel and membrane as a function of H⁺ ion concentration in the equilibrating aqueous solution indicated that ionic species held in the membrane and gel were not same. These results indicated that proximity of functional groups (phosphate) plays an important role in metal ion binding with polymeric EGMP.     

Composite proton-conducting membranes based on poly(ethylene glycol vinyl glycidyl ether)

Composite proton-conducting membranes in the form of interpolymer films are prepared in an aqueous medium from sulfo-acid-modified poly(ethylene glycol vinyl glycidyl ether) and poly(vinyl alcohol). The initial poly(hydroxysulfo acid) is synthesized through the radical polymerization of ethylene glycol vinyl glycidyl ether followed by modification with sodium sulfite via epoxy groups and treatment with a cationite in the H form. The proton-conducting membranes feature improved thermal stability (200–250°C), a breaking strength of 1.0–8.9 MPa, elasticity (a relative elongation at break of 1.0–8.2%), chemical resistance, and specific proton conductivity attaining 10^?1 S/cm after doping with orthophosphoric acid.     

Interlayer reactions of the silver molybdate Ag6Mo10O33

Silver molybdate Ag₆Mo₁₀O₃₃ exchanges silver ions for organic cations, particularly surface-active agents such as long-chain n-alkylammonium ions C_nH_2n+1NH⁺₃. The alkylammonium ions penetrate between the layers and aggregate as bimolecular structures. The alkyl chains in the interlayer are not in all-trans conformation but are isomerized into conformers with gauche-bonds. These chains aggregate as gauche-blocks because the polar chain ends (NH⁺₃ and NH₂ groups) interacting with the molybdate layer cannot be close-packed. The specially favored formation and pronounced stability of gauche-blocks impede the quantitative exchange of the silver ions. No more than 20% of the silver ions are exchanged by alkylammonium nitrate. The gauche-blocks are stabilized by additional uptake of alkylamine molecules. Silver molybdate also reacts with alkylamine and forms long-spacing complexes with long segments of the alkyl chains perpendicular to the layers.     

Polymeric hydrogels modified with ornithine and lysine: Sorption and release of metal cations and amino acids

A novel, convenient synthesis, using copper ions, is described for the multigram‐scale preparation of acryloyl and methacryloyl ornithine and lysine without the need to use protecting groups and chromatographic purifications. Three methods of removing the copper ions from the amino acid derivatives were examined. The obtained acryloyl and methacryloyl ornithine and lysine were copolymerized with N‐isopropylacrylamide and N,N′‐methylenebisacrylamide as crosslinking agents, resulting in a series of hydrogels with varying incorporated amino acid content. The relative content of a given amino acid was estimated from the ¹H NMR data and compared with its molar fraction used in the polymerization process. We investigated the influence of the amount of amino acid groups incorporated into the polymer network on the swelling behavior of the gels in the presence of metal ions of different ability to form complexes (Cu²⁺, Co²⁺, and Ca²⁺) with α‐amino acid groups and the sorption of copper ions. Next, the presence of α‐amino acid groups attached to the polymer network was used to bond the compounds which can cocomplex metal ions. Phenylalanine was selected for examination of its cocomplexation of Cu²⁺ with the polymer‐network amino acids and its consecutive release from the gel after appropriate change of pH. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Rate of Generation of Ions H<Superscript>+</Superscript> and OH<Superscript>−</Superscript> at the Ion-Exchange Membrane/Dilute Solution Interface as a Function of the Current Density

Partial currents of water dissociation products through cation- and anion-exchange membranes that form thin desalination channels in electrodialyzers are measured. The investigations are performed in a broad interval of flow rates during desalination of dilute sodium chloride solutions at overlimiting currents. A water dissociation theory, which was developed for bipolar membranes, and a mass transfer theory that allows for the space charge formation at overlimiting currents are used to derive an expression, according to which the rate of generation of the H⁺ and OH^? ions is defined by the ratio of the current density to its critical value at which water starts undergoing discernible dissociation.     

Electrolytic Synthesis of Complex Oxide Systems by Cathodic Deposition of Molybdenum Oxide from Aqueous Solutions in the Presence of Nickel(II) and Thiosulfate Ions

Cathodic processes occurring in electrolytic deposition of molybdenum oxide from aqueous solutions of sodium molybdate in the presence of nickel(II) and thiosulfate ions were studied. Conditions for formation of cathodic deposits in the form of complex oxide systems Mo-Ni and Mo₄O_{1 1}-MoS₂ were determined.     

Comparative Studies of Tridentate Sulfur and Nitrogen‐Containing Ligands as Ionophores for Construction of Cadmium Ion‐Selective Membrane Sensors

New polymeric membrane cadmium‐ion selective sensors have been prepared by incorporating nitrogen and sulfur containing tridentate ligands as the ionophores into the plasticized PVC membranes. Poly(vinyl chloride) (PVC) based membranes of potassium hydrotris[N‐(2,6‐xylyl)thioimdazolyl) borate] (KTt^2,6‐xylyl) and potassium hydrotris(3‐phenyl‐5‐methylpyrazolyl) borate (KTp^Ph,Me) with sodium tetraphenyl borate (NaTPB) as an anionic excluder and dibutylphthalate (DBP), tributylphthalate (TBP), dioctylsebacate (DOS), and o‐nitrophenyloctyl ether (o‐NPOE) as plasticizing solvent mediators were investigated in different compositions. KTt^2,6‐xylyl was found to be a selective and sensitive ion carrier for Cd(II) membrane sensor. A membrane composed of KTt^2,6‐xylyl:NaTPB:PVC:DBP with the % mole ratio 2.3 : 1.1 : 34.8 : 61.8 (w/w) works well over a very wide concentration range (7.8×10^?8–1.0×10^?2 M) with a Nernstian slope of 29.4±0.2 mV/decades of activity between pH values of 3.5 to 9.0 with a detection limit of 4.37×10^?8 M. The sensor displays very good discrimination toward Cd(II) ions with regard to most common cations. The proposed sensor shows a short response time for whole concentration range (ca. 8 s). The effects of the cationic (tetrabutylammonium chloride, TBC), anionic (sodium dodecyl sulfate, SDS) and nonionic (Triton X‐100) surfactants were investigated on the potentiometric properties of proposed cadmium‐selective sensor. The proposed sensor based on KTt^2,6‐xylyl ionophore has also been used for the direct determination of cadmium ions in different water samples and human urine samples.