Direct syntheses of Lan+1NinO3n+1 phases (n=1, 2, 3 and ∞) from nanosized co-crystallites

A new direct route for the “bottom up” syntheses of phases in the La_n+1Ni_nO_3n+1 series (n=1, 2, 3 and ∞) has been achieved via single-step heat treatments of nanosized co-crystallized precursors. The co-crystallized precursors were prepared using a continuous hydrothermal flow synthesis system that uses a superheated water flow at ca. 400 °C and 24.1 MPa to produce nanoparticulate slurries. Overall, a significant reduction in time and number of steps for the syntheses of La₃Ni₂O₇ and La₄Ni₃O₁₀ was achieved compared with more conventional synthesis methods, which typically require multiple homogenization and reheating steps over several days.     

Structure and phase composition of nanocrystalline Ce1−xLuxO2−y

The microstructure and phase stability of nanocrystalline mixed oxide Lu_xCe_1−xO_2−y (x=0-1) are described. Nano-sized (3-4 nm) oxide particles were prepared by the reverse microemulsion method. Morphological and structural changes upon heat treatment in an oxidizing atmosphere were studied by transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman and Yb³⁺ emission spectroscopy, the latter ion being present as an impurity in the Lu₂O₃ starting material. Up to 950 °C, the samples were single phase, with structure changing smoothly with Lu content from fluorite type (F) to bixbyite type (C). For the samples heated at 1100 °C phase separation into coexisting F- and C-type structures was observed for 0.35<x<0.7. It was also found that addition of Lu strongly hinders the crystallite growth of ceria during heat treatment at 800 and 950 °C.     

Thermochemistry of Li1+xMn2−xO4 (0?x?1/3) spinel

Lithium substituted Li_1+xMn_2−xO₄ spinel samples in the entire solid solution range (0?x?1/3) were synthesized by solid-state reaction. The samples with x<0.25 are stoichiometric and those with x?0.25 are oxygen deficient. High-temperature oxide melt solution calorimetry in molten 3Na₂O·4MoO₃ at 974 K was performed to determine their enthalpies of formation from constituent binary oxides at 298 K. The cubic lattice parameter was determined from least-squares fitting of powder XRD data. The variations of the enthalpy of formation from oxides and the lattice parameter with x follow similar trends. The enthalpy of formation from oxides becomes more exothermic with x for stoichiometric compounds (x<0.25) and deviates endothermically from this trend for oxygen-deficient samples (x?0.25). This energetic trend is related to two competing substitution mechanisms of lithium for manganese (oxidation of Mn³⁺ to Mn⁴⁺ versus formation of oxygen vacancies). For stoichiometric spinels, the oxidation of Mn³⁺ to Mn⁴⁺ is dominant, whereas for oxygen-deficient compounds both mechanisms are operative. The endothermic deviation is ascribed to the large endothermic enthalpy of reduction.     

Density-functional study for the NOx (x = 1, 2) dissociation mechanism on the Cu(1 1 1) surface

Spin-polarized density functional theory calculation is employed to study the adsorption and dissociation of NO₂ molecule on Cu(1 1 1) surface. It is shown that the most favorable adsorption structure is the NO₂ (T,T-O-,O′-nitrito) configuration which has an adsorption energy of −1.49 eV. The barriers for step-wise NO₂ dissociation reaction, NO_2(g) → N_(a) + 2O_(a), are 1.05 (for O–N–O bond activation), and 2.08 eV (for N–O bond activation), respectively, and the entire process is 0.6 eV exothermic. The energetics of single N–O dissociation with and without the presence of N atom or O atom on the surface are also calculated. The results indicate that in the presence of O atom on Cu(1 1 1) surface would raise the N–O dissociation barrier, whereas in the presence of N atom decrease it. The interaction nature between adsorbates and substrate is analyzed by the local density of states (LDOS) calculation.     

Syntheses,structures and luminescent properties of four copper(I) cyanide coordination polymers based on 2-(n-pyridyl)benzimidazole ligands (n = 2, 3, 4)

Four copper(I) cyanide coordination polymers containing 2-(n-pyridyl)benzimidazole ligands, namely [Cu₂(CN)(2-PyBIm)]_n (1), [Cu₂(CN)₂(3-PyHBIm)]_n (2), {[Cu₃(CN)₃(4-PyHBIm)₄] · 2H₂O}_n (3) and [Cu₅(CN)₃(4-PyBIm)₂]_n (4), have been synthesized and characterized by X-ray crystallography. Complex 1 is a one-dimension coordination polymer in which 2-(2-pyridyl)benzimidazole is deprotonated and adopts a bridging tridentate coordination mode. Complex 2 has ladder-like structure in which 2-(3-pyridyl)benzimidazole does not deprotonate and acts as a bidentate bridge. Complex 3 displays a saddle-shaped helical chain constructed through μ₂-cyanide group and the outstretched neutral 2-(4-pyridyl)benzimidazole monodentate ligand. Complex 4 shows two-dimension layer polymeric structure in which deprotonated 2-(4-pyridyl)benzimidazole acts as a tridentate bridging ligand. The cyanide groups in four complexes all act as bidentate bridging ligands. These complexes are thermal stable and display luminescence in the solid states.     

Composition-induced structural phase transitions in the (Ba1−xLax)2In2O5+x (0?x?0.6) system

Composition-induced structural phase changes across the high temperature, fast oxide ion conducting (Ba_1−xLa_x)₂In₂O_5+x, 0?x?0.6, system have been carefully analysed using hard mode infrared (IR) powder absorption spectroscopy, X-ray powder diffraction and electron diffraction. An orthorhombic brownmillerite to three-dimensionally disordered cubic perovskite phase transition in this system is signalled by a drastic change in slope of both wavenumber and average line widths of IR spectra as a function of composition. Some evidence is found for the existence of an intermediate tetragonal phase (previously reported to exist from electron diffraction data) around x∼0.2. The new spectroscopic data have been used to compare microscopic and macroscopic strain parameters arising from variation in composition. The strain and spectroscopic data are consistent with first-order character for the tetragonal→orthorhombic transition, while the cubic→tetragonal transition could be continuous. Differences between the variation with composition of spectral parameters and of macroscopic strain parameters are consistent with a substantial order/disorder component for the transitions. There is also evidence for precursor effects within the cubic structure before symmetry is broken.     

Determination of thermodynamic properties of aqueous mixtures of MgCl2 and Mg(NO3)2 by the potentiometric method at T = 298.15

In this research, thermodynamic properties of the ternary electrolyte system (MgCl₂ + Mg(NO₃)₂ + H₂O) were investigated using a potentiometric method. The galvanic cell used had no liquid junction of type: Mg-ISE|MgCl₂ (m_A), Mg(NO₃)₂ (m_B), H₂O|Ag/AgCl. The measurements were performed at T = 298.15 K and at total ionic strengths from 0.001 to 8.000 mol/kg for different series of salt ratios r=mMgCl₂/mMg₂(NO₃) =1.00, 2.50, 5.00, 7.50, 10.00 and 15.00. The PVC based magnesium ion-selective electrode (Mg-ISE) and the Ag/AgCl electrode used in this work were prepared in our laboratory and showed a reasonably good Nernst response. The Pitzer ion interaction model and Harned rule were used to illustrate the ternary electrolyte system investigated. The experimental results showed that both Pitzer model and Harned rule were suitable to be used satisfactorily to describe this ternary system.     

Theoretical study of electronic spectra of linear carbon clusters HC2nS (n = 1–5)

In this work we report the structures and stabilities of linear carbon clusters HC_2nS (n = 1–5) in their ground states using the B3LYP density functional. The rotational constants at the optimized geometries give excellent agreement with the experimental and previous theoretical values. The vertical excitation energies of the 2²Π ← X²Π transitions at the CASPT2 level are 3.16, 2.66, 2.05, 1.78, and 1.55 eV, respectively, in good agreement with the corresponding observed values of 3.01, 2.48, 2.10, 1.84, and 1.65 eV. Also, the exponential-decay curves for these vertical excitation energies obtained from experiments and theoretical calculations are illuminated.     

La3Ru8B6 and Y3Os8B6, new members of a homologous series R(A)nM3n−1B2n

Two new compounds, La₃Ru₈B₆ and Y₃Os₈B₆, were synthesized by arc melting the elements. Their structural characterization was carried out at room temperature on as-cast samples by using X-ray diffractometry. According to X-ray single-crystal diffraction results these borides crystallize in Fmmm space group (no. 69), Z=4, a=5.5607(1) Å, b=9.8035(3) Å, c=17.5524(4) Å, ρ=8.956 Mg/m³, μ=25.23 mm⁻¹ for La₃Ru₈B₆ and a=5.4792(2) Å, b=9.5139(4) Å, c=17.6972(8) Å, ρ=13.343 Mg/m³, μ=128.23 mm⁻¹ for Y₃Os₈B₆. The crystal structure of La₃Ru₈B₆ was confirmed from Rietveld refinement of X-ray powder diffraction data. Both La₃Ru₈B₆ and Y₃Os₈B₆ compounds are isotypic with the Ca₃Rh₈B₆ compound and their structures are built up from CeCo₃B₂-type and CeAl₂Ga₂-type structural fragments taken in ratio 2:1. They are the members of structural series R(A)_nM_3n−1B_2n with n=3 (R is the rare earth metal, A the alkaline earth metal, and M the transition metal). Structural and atomic parameters were also obtained for La_0.94Ru₃B₂ compound from Rietveld refinement (CeCo₃B₂-type structure, P6/mmm space group (no. 191), a=5.5835(9) Å, c=3.0278(6) Å).     

First-principles study of the electronic and magnetic properties of oxygen-deficient rutile TiO2(1 1 0) surface

Based on first-principles electronic structure calculations we find that the bridging oxygen vacancies on the (1 1 0) surface is more favorable and may be responsible for the unexpected ferromagnetism in undoped rutile TiO₂. Our results show that the ferromagnetism largely originates from the d orbitals of low-charge-state Ti ions converted from Ti⁴⁺ ions induced by the surface oxygen vacancies. The second-nearest neighbors of these ions (fivefold coordinated Ti) also contribute to the total magnetic moments. The spins induced by the local oxygen vacancies form a ferromagnetic arrangement.     

A novel route to synthesize cubic ZrW2−xMoxO8 (x=0-1.3) solid solutions and their negative thermal expansion properties

Cubic ZrW_2−xMo_xO₈ (c-ZrW_2−xMo_xO₈) (x=0-1.3) solid solutions were prepared by a novel polymorphous precursor transition route. X-ray diffraction (XRD) analysis reveals that the solid solutions are single phase with α- and β-ZrW₂O₈ structure for 0?x?0.8 and 0.9?x?1.3, respectively. The optimum synthesis conditions of ZrWMoO₈ are obtained from differential scanning calorimetry-thermal gravimetric analysis (DSC-TGA), XRD and mass loss-temperature/time curves. Following the above experience, the stoichiometric solid solutions of c-ZrW_2−xMo_xO₈ (x=0-1) are obtained within 1 wt% of mass loss. The relationships of lattice parameters (a), phase transition temperatures (T_c) and instantaneous coefficients of thermal expansion (α_i) against the content x of Mo are discussed based on the variation of order degree parameters of ZrW_2−xMo_xO₈.     

(p, ρ, T) properties, and apparent molar volumes V? of ZnBr2 in methanol at T = (298.15 to 398.15) K and pressures up to p = 40 MPa

The (p, ρ, T) properties of pure methanol, the (p, ρ, T) properties and apparent molar volumes V_? of ZnBr₂ in methanol at T = (298.15 to 398.15) K and pressures up to p = 40 MPa are reported, and apparent molar volumes have been evaluated. The experimental (p, ρ, T, m) values were described by an equation of state. For the solutions the experiments were carried out at molalities m = (0.05772, 0.37852, 0.71585 and 1.95061) mol · kg⁻¹ of zinc bromide.     

Synthesis, optical properties and electronic structures of polyoxometalates K3P(Mo1−xWx)12O40 (0?x?1)

Various compositions of solid solutions K₃P(Mo_1−xW_x)₁₂O₄₀ (0?x?1) were prepared using two solid state synthetic routes. The crystallite size was determined by linewidth refinements of X-ray diffraction patterns using the Warren-Averbach method, and the grain size distribution by laser scattering experiments. Optical properties were determined by diffuse reflectance measurements in the UV-visible range. The optical gap E_g was found to increase exponentially from ∼2.5 to ∼3.30 eV with increasing x, and is systematically shifted to a higher energy when the grain size decreases. The relation between E_g and x was analyzed by calculating the HOMO-LUMO gaps of the [P(Mo_1−xW_x)₁₂O₄₀]³⁻ anions on the basis of tight-binding electronic structure calculations.     

Local environment in Ba2In2−xWxO5+3x/2 oxide ion conductors

The actual oxygen environment of the tungsten dopant in the Ba₂In_2−xW_xO_5+3x/2 solid solution was revealed by combining X-ray absorption spectroscopy at the tungsten L_I and L_III edges and at the indium L_I edge. Whatever the substitution ratio, the tungsten atoms exhibit a regular octahedral environment. When the substitution ratio increases, the oxygen vacancies are progressively filled until their total occupancy for x=2/3. For x?0.3, the perovskite structure is stabilised; the tungsten atoms are randomly distributed in the structure. Although X-ray diffraction revealed a cubic symmetry for these compositions, a local distortion of the indium environment is observed when a tungsten atom is in its surrounding.     

Separation of aromatic hydrocarbons from alkanes using ammonium ionic liquid C2NTf2 at T = 298.15 K

(Liquid + liquid) equilibrium data are presented for four ternary systems of an alkane, or aromatic compound and ethyl(2-hydroxyethyl)dimethylammonium bis{(trifluomethyl)sulfonyl}imide (C₂NTf₂) at 298.15 K: [hexane + benzene + C₂NTf₂], [hexane + p-xylene + C₂NTf₂], and [hexane, or octane + m-xylene + C₂NTf₂]. The separation of aromatic hydrocarbons (benzene, or p-xylene, or m-xylene) from aliphatic hydrocarbons (hexane, or octane) is investigated by extraction with the ammonium ionic liquid. Selectivities and distribution ratios are discussed for these mixtures at constant temperature. The data were analysed and compared to those previously reported for other ionic liquids and especially for the system {hexane + benzene + [EMIM][NTf₂]}. The nonrandom two liquid NRTL model was successfully used to correlate the experimental tie-lines and to calculate the phase compositions of the ternary systems.     

Phase relations in NaxCrxTi8−xO16 at 1350 °C and crystal structure of hollandite-like Na2Cr2Ti6O16

Phase relations of rutile, freudenbergite, and hollandite structures were examined in the pseudobinary system NaCrO₂-TiO₂ (i.e., Na_xCr_xTi_8−xO₁₆) at 1350 °C. The hollandite structure was obtained in the composition range 1.7?x?2.0. The symmetry of the samples at room temperature was tetragonal for x=1.7 and 1.75, and monoclinic for x=1.8 and above. Single crystals of monoclinic hollandite Na₂Cr₂Ti₆O₁₆ were grown and the structure refinement has been carried out using an X-ray diffraction technique. The space group was I2/m and cell parameters were a=10.2385(11), b=2.9559(9), c=9.9097(11)Å, and β=90.545(9)° with Z=1. The Na ion distribution in the tunnel was markedly deformed from that in the tetragonal form. It was suggested that Cr/Ti ratios were different between the two framework metal sites.     

Structure and magnetic properties of the orthorhombic n=2 Ruddlesden-Popper phases Sr3Co2O5+δ (δ=0.91, 0.64 and 0.38)

The reduced Ruddlesden-Popper phases, Sr₃Co₂O_5+δ with δ=0.91, 0.64 and 0.38, have been prepared in a nitrogen atmosphere. The crystal structures were determined by powder neutron diffraction. Oxygen vacancies are found both in O(3) and O(4) sites but the majority are along one crystallographic axis in the CoO₂ plane, inducing an orthorhombic distortion of the normally tetragonal n=2 Ruddelsden-Popper structure. Superstructures due to oxygen ordering are observed by electron microscopy. The magnetic measurements reveal complex behavior with some ferromagnetic interactions present for Sr₃Co₂O_5.91 and Sr₃Co₂O_5.64.     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.     

Theoretical study of the thermochemistry and the kinetics of the SFxCl (x = 0-5) series

A systematic thermodynamic and kinetic study of the entire SF_xCl (x = 0-5) series has been carried out. High-level quantum chemical composite methods have been employed to derive enthalpy of formation values from calculated atomization and isodesmic energies. The resulting values for the SCl, SFCl, SF₂Cl(C₁), SF₃Cl(C_s), SF₄Cl(C_s) and SF₅Cl molecules are 28.0, −36.0, −64.2, −134.3, −158.2 and −237.1 kcal mol⁻¹. A comparison with previous experimental and theoretical values is presented. Statistical adiabatic channel model/classical trajectory, SACM/CT, calculations of selected complex-forming and recombination reactions of F and Cl atoms with radicals of the series have been performed between 200 and 500 K. The reported rate coefficients span over the normal range of about 6 × 10⁻¹² and 5 × 10⁻¹¹ cm³ molecule⁻¹ s⁻¹ expected for this type of barrierless reactions.     

A computational study of SbnF5n (n = 1-4): Implications for the fluoride ion affinity of nSbF5

This contributions shows with a series of ab initio MP2 and DFT (BP86 and B3-LYP) computations with large basis sets up to cc-pVQZ quality that the literature value of the standard enthalpy of depolymerization of Sb₄F_20(g) to give SbF_5(g) (+18.5 kJ mol⁻¹) [J. Fawcett, J.H. Holloway, R.D. Peacock, D.R. Russell, J. Fluorine Chem. 20 (1982) 9] is by about 50 kJ mol⁻¹ in error and that the correct value of (Sb₄F_20(g)) is +68 ± 10 kJ mol⁻¹. We assign , , and values for Sb_nF_5n with n = 2-4 and compare the results to available experimental gas phase data. Especially the MP2/TZVPP values obtained in an indirect procedure that rely on isodesmic reactions or the highly accurate compound methods G2 and CBS-Q are in excellent agreement with the experimental data, and reproduce also the fine experimental details at temperatures of 423 and 498 K. With these data and the additional calculation of [Sb_nF_5n+1]⁻ (n = 1-4), we then assessed the fluoride ion affinities (FIAs) of Sb_nF_5n(g), nSbF_5(g), nSbF_5(l) and the standard enthalpies of formation of Sb_nF_5n(g) and [Sb_nF_5n+1]⁻_(g): FIA(Sb_nF_5n(g)) = 514 (n = 1), 559 (n = 2), 572 (n = 3) and 580 (n = 4) kJ mol⁻¹; FIA(nSbF_5(g)) = 667 (n = 2), 767 (n = 3) and 855 (n = 4) kJ mol⁻¹; FIA(nSbF_5(l)) = 434 (n = 1), 506 (n = 2), 528 (n = 3) and 534 (n = 4) kJ mol⁻¹. Error bars are approximately ±10 kJ mol⁻¹. Also the related Gibbs energies were derived. Δ_fH°([Sb_nF_5n+1]⁻_(g)) = −2064 ± 18 (n = 1), −3516 ± 25 (n = 2), −4919 ± 31 (n = 3) and −6305 ± 36 (n = 4) kJ mol⁻¹.