Catalytic performance of metal oxide modified SiMCM-41 catalysts in diphenyl carbonate synthesis

Decomposition of CCl₄ into diphenyl carbonate (DPC) was examined over metal oxides modified SiMCM-41. ZnO/SiMCM-41 and Fe₂O₃/SiMCM-41 showed high activity in DPC synthesis. Although many other metal oxides, such as La₂O₃, CuO, Al₂O₃ and alkali or alkaline earth oxide, were success in destruction of CCl₄, they displayed nearly no activity on DPC synthesis. ZnO/SiMCM-41 and Fe₂O₃/SiMCM-41 were characterized by X-ray diffraction (XRD), UV-Raman, ²⁹Si MAS NMR and N₂ adsorption-desorption isotherms, and results showed that ferric and zinc oxide were supported onto SiMCM-41. The well ZnO dispersion in SiMCM-41 channels and the weak electrostatic interaction between chlorine anion and Zn²⁺ play an important role for the high activity of ZnO/SiMCM-41 in decomposition of CCl₄ into DPC.     

Supported Intermetallic PdZn Nanoparticles as Bifunctional Catalysts for the Direct Synthesis of Dimethyl Ether from CO‐Rich Synthesis Gas

The single‐step syngas‐to‐dimethyl ether (STD) process entails economic and technical advantages over the current industrial two‐step process. Pd/ZnO‐based catalysts have recently emerged as interesting alternatives to currently used Cu/ZnO/Al₂O₃ catalysts, but the nature of the active site(s), the reaction mechanism, and the role of Pd and ZnO in the solid catalyst are not well established. Now, Zn‐stabilized Pd colloids with a size of 2 nm served as the key building blocks for the methanol active component in bifunctional Pd/ZnO‐γ‐Al₂O₃ catalysts. The catalysts were characterized by combining high‐pressure operando X‐ray absorption spectroscopy and DFT calculations. The enhanced stability, longevity, and high dimethyl ether selectivity observed makes Pd/ZnO‐γ‐Al₂O₃ an effective alternative system for the STD process compared to Cu/ZnO/γ‐Al₂O₃.     

金属有机骨架材料MIL-53(Al)负载钴催化剂的CO催化氧化反应性能

采用溶剂法合成了热稳定性高的金属有机骨架材料MIL-53(Al)(MIL:Materials of Institut Lavoisier),用此材料为载体负载钴催化剂用于CO的催化氧化反应,并与Al2O3负载的钴催化剂进行了对比.采用热重-差热扫描量热(TG-DSC)、傅里叶变换红外(FTIR)光谱、X射线衍射(XRD)、N2物理吸附-脱附、透射电子显微镜(TEM)、氢气程序升温还原(H2-TPR)等方法对催化剂的结构性质进行了表征.TG和N2物理吸附-脱附结果表明,载体MIL-53(Al)有好的稳定性和高的比表面积;XRD以及TEM结果表明Co/MIL-53(Al)上负载的Co3O4颗粒粒径(平均约为5.03 nm)明显小于Al2O3上Co3O4颗粒粒径(平均约为7.83 nm).MIL-53(Al)的三维多孔结构中分布均匀的位点能很好地分散固定Co3O4颗粒,高度分散的Co3O4颗粒有利于CO的催化氧化反应.H2-TPR实验发现Co/MIL(Al)催化剂的还原温度低于Co/Al2O3催化剂的还原温度,低的还原温度表现为高的催化氧化活性.CO催化氧化结果表明,MIL-53(Al)负载钴催化剂的催化活性明显高于Al2O3负载钴催化剂,MIL-53(Al)负载钴催化剂在160°C时使CO氧化的转化率达到98%,到180°C时CO则完全转化,催化剂的结构在催化反应过程中保持稳定.     

乙烷氧化脱氢用Ni/Al2O3催化剂中活性镍物种前驱体（英文）

Ni/Al2O3 catalysts for oxidative dehydrogenation(ODH) of ethane were prepared by impregnation of Al2O3 with nickel acetate or nickel nitrate,and by mechanical mixing of NiO and Al2O3.The Ni-based catalysts were characterized by N2 adsorption-desorption,X-ray diffraction,diffuse reflectance UV-visible diffuse reflectance spectroscopy,and temperature-programmed reduction of hydrogen.The results showed that formation of crystalline NiO particles with a size of < 8 nm and/or non-stoichiometric NiO species in the Ni/Al2O3 catalysts led to more active species in ODH of ethane under the investigated reaction conditions.In contrast,tetrahedral Ni species present in the catalysts led to higher selectivity for ethene.Formation of large crystalline NiO particles(22-32 nm) over Ni/Al2O3 catalysts decreased the selectivity for ethene.     

ZnO添加量对Pd/Zr0.5Al0.5O1.75催化剂净化稀燃天然气汽车尾气性能的影响

以掺杂不同含量ZnO的Zr_0.5Al_0.5O_1.75为载体,制备了系列1.5%Pd催化剂.在模拟稀燃天然气汽车尾气条件下,测试了催化剂的活性和抗水性,并用N₂吸附-脱附、X射线衍射、H₂程序升温还原和X射线光电子能谱等手段对催化剂进行了系统表征.研究结果表明,ZnO的添加及添加量对催化剂的活性和抗H₂O性有明显影响,其中以ZnO添加量为15%时制备的复合氧化物为载体的催化剂活性最佳.当模拟尾气中不含H₂O时,该催化剂对甲烷的起燃温度（T₅₀）和完全转化温度（T₉₀）分别为278和314℃;在含H₂O时,该催化剂的T₅₀和T₉₀分别为342和371℃.     

国产航空煤油裂解催化剂Pt/ZrxTixAl1-2xO2的性能

采用共沉淀法制备了一系列Zr_xTi_xAl_1-2xO₂复合氧化物载体材料,考察了其作为裂解催化剂载体对航空煤油裂解反应的影响.?采用全自动吸附仪、X射线衍射、扫描电镜/能谱仪联用、NH₃-程序升温脱附等手段对催化剂进行了表征.?结果表明,当ZrO₂：TiO₂：Al₂O₃质量比为1：1：3时催化剂具有最大的比表面积和孔容;具有最强的表面酸性和最集中的强酸中心密度,且具有良好的再生功能.?实验结果表明,载体ZrO₂：TiO₂：Al₂O₃质量比为1：1：3时催化剂上650?℃裂解产气量较热裂解提高了2.1倍,700?℃时提高1.4倍.?另外,该系列载体材料经1000?℃焙烧5?h后,所制得的催化剂几乎失去了催化活性.     

Development of high performance Cu/ZnO-based catalysts for methanol synthesis and the water-gas shift reaction

Our groups studies on Cu/ZnO-based catalysts for methanol synthesis via hydrogenation of CO₂ and for the water-gas shift reaction are reviewed. Effects of ZnO contained in supported Cu-based catalysts on their activities for several reactions were investigated. The addition of ZnO to Cu-based catalyst supported on Al₂O₃, ZrO₂ or SiO₂ improved its specific activity for methanol synthesis and the reverse water-gas shift reaction, but did not improve its specific activity for methanol steam reforming and the water-gas shift reaction. Methanol synthesis from CO₂ and H₂ over Cu/ZnO-based catalysts was extensively studied under a joint research project between National Institute for Resources and Environment (NIRE; one of the former research institutes reorganized to AIST) and Research Institute of Innovative Technology for the Earth (RITE). It was suggested that methanol should be produced via the hydrogenation of CO₂, but not via the hydrogenation of CO, and that H₂O produced along with methanol should greatly suppress methanol synthesis. The Cu/ZnO-based multicomponent catalysts such as Cu/ZnO/ZrO₂/Al₂O₃ and Cu/ZnO/ZrO₂/Al₂O₃/Ga₂O₃ were highly active for methanol synthesis from CO₂ and H₂. The addition of a small amount of colloidal silica to the multicomponent catalysts greatly improved their long-term stability during methanol synthesis from CO₂ and H₂. The purity of the crude methanol produced in a bench plant was 99.9 wt% and higher than that of the crude methanol from a commercial methanol synthesis from syngas. The water-gas shift reaction over Cu/ZnO-based catalysts was also studied. The activity of Cu/ZnO/ZrO₂/Al₂O₃ catalyst for the water-gas shift reaction at 523 K was less affected by the pre-treatments such as calcination and treatment in H₂ at high temperatures than that of the Cu/ZnO/Al₂O₃ catalyst. Accordingly, the Cu/ZnO/ZrO₂/Al₂O₃ catalyst was considered to be more suitable for practical use for the water-gas shift reaction. The Cu/ZnO/ZrO₂/Al₂O₃ catalyst was also highly active for the water-gas shift reaction at 673 K. Furthermore, a two-stage reaction system composed of the first reaction zone for the water-gas shift reaction at 673 K and the second reaction zone for the reaction at 523 K was found to be more efficient than a one-stage reaction system. The addition of a small amount of colloidal silica to a Cu/ZnO-based catalyst greatly improved its long-term stability in the water-gas shift reaction in a similar manner as in methanol synthesis from CO₂ and H₂.     

Time-on stream behavior of Pd-, Co-, and Mn-zeolite catalysts supported on metal blocks in high-temperature methane oxidation

Stability of the Pd-, Co-, and Mn-zeolite catalysts supported on metal blocks was studied in high-temperature methane oxidation. The temperature regions were found in which the starting catalysts exhibit stable performance. The temperature was determined at which a partial deactivation is followed by stabilization of catalysts in reaction environment. In terms of specific activity, the partially deactivated Pd-zeolite catalyst is several times more active than conventional oxidation catalysts Pd/Al₂O₃, Pt/Al₂O₃, and the most active oxide CeO·6Al₂O₃.__________Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 10, pp. 2075–2078, October, 2004.     

Catalytic dehydrogenation of ethanol into acetaldehyde and isobutanol using mono- and multicomponent copper catalysts

The purpose of this work was to investigate biomass-derived ethanol dehydrogenation into acetaldehyde using several mono- and multicomponent (CuO, ZnO and Cr₂O₃)-containing catalysts supported on industrial size Al₂O₃ beads. The catalysts, prepared with either solution combustion or incipient wetness method, were characterized by using various physico-chemical methods, such as EDXA, SEM-EDXA, TEM, XRD, XPS, pyridine adsorption desorption FTIR, and ζ-potential measurements. The results revealed that the multicomponent catalysts exhibited superior activity compared to the metal oxide catalysts containing only one metal oxide. In addition, the most selective catalyst towards acetaldehyde formation, with 50% selectivity at 55% conversion of ethanol at 300 °C and WHSV 1 h^?1 was CuOCr₂O₃/Al₂O₃ prepared by using the solution combustion method, indicating that this inexpensive and rapid catalyst preparation method is promising for other applications.     

Vapour phase synthesis of quinoline from aniline and glycerol over mixed oxide catalysts

The vapour phase synthesis of quinoline from aniline and glycerol (1:2 mole ratio) in a single step was investigated over ZnO–Cr₂O₃, CuO–ZnO/Al₂O₃, MoO₃–V₂O₅/Al₂O₃ and NiO–MoO₃/Al₂O₃ catalysts in the presence of air at 623–723 K under normal atmospheric pressure. Among these catalysts investigated, the CuO–ZnO/Al₂O₃ combination effectively performed this reaction with high activity and selectivity.     

Resistance to sulfur poisoning of Rh supported catalysts

Sulfur thiotolerance by thiophene during toluene hydrogenation on rhodium supported catalysts prepared on different supports and metal precursors have been studied. The catalysts were characterized by H₂ chemisorption, TEM, TPD of ammonia and XPS. The turnover frequency of the reaction does not change significantly with the carrier but in the presence of 10 ppm of thiophene a drastic decrease in the activity is observed. The initial deactivation constant follows the order Rh/SiO₂>Rh/TiO₂>Rh/Al₂O₃.     

Ethylcyclopentane ring opening reaction over PtGe/Al2O3 catalysts prepared by controlled surface reaction

Platinum-germanium catalysts supported on a non-acidic Al₂O₃ have been prepared by adding Ge in amounts corresponding nominally to 1/8 (PtGe1/8/Al₂O₃); 1/2 (PtGe1/2/Al₂O₃); 1 (PtGe1/Al₂O₃) and 2 (PtGe2/Al₂O₃) monolayers by controlled surface reaction of Ge(n-C₄H₉)₄ to Pt/Al₂O₃. These catalysts were characterized by electron microscopy (TEM), FTIR of CO adsorption and H₂ chemisorption. The ring opening of ethylcyclopentane (ECP) was studied as a test reaction between 543 and 633 K. PtGe1/8/Al₂O₃ catalyst produced the most ring opening products (ROP) in the whole temperature range. A good agreement with statistical values of ROP was observed at low temperature, but at higher temperature, the opening became selective, producing mostly heptane. Bimetallic catalysts PtGe1/Al₂O₃ and PtGe2/Al₂O₃ led to a nonselective hydrogenolysis, similar to the monometallic platinum catalyst Pt/Al₂O₃. The catalysts PtGe1/Al₂O₃ and PtGe2/Al₂O₃ produced ROP with the lowest selectivity; instead, much aromatics and fragments were formed, in increasing amounts above 600 K.     

Effect of Ni loadings on the activity and coke formation of MgO-modified Ni/Al2O3 nanocatalyst in dry reforming of methane

MgO-modified Ni/Al₂O₃ catalysts with different Ni loadings were prepared and employed in dry reforming of methane (DRM). The effect of Ni loadings on the activity and coke formation of Ni/MgO-Al₂O₃ catalysts were investigated. The synthesized catalysts were characterized by XRD, N₂ adsorption-desorption, SEM, TPO and TPR techniques. The obtained results showed that increasing nickel loading decreased the BET surface area and increased the catalytic activity and amount of deposited carbon. In addition, the effect of gas hourly space velocity (GHSV) and feed ratio were studied.     

Gold catalysts supported on ZnO/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for low-temperature CO oxidation

Gold catalysts with loadings ranging from 0.5 to 7.0 wt% on a ZnO/Al₂O₃ support were prepared by the deposition–precipitation method (Au/ZnO/Al₂O₃) with ammonium bicarbonate as the precipitation agent and were evaluated for performance in CO oxidation. These catalysts were characterized by inductively coupled plasma-atom emission spectrometry, temperature programmed reduction, and scanning transmission electron microscopy. The catalytic activity for CO oxidation was measured using a flow reactor under atmospheric pressure. Catalytic activity was found to be strongly dependent on the reduction property of oxygen adsorbed on the gold surface, which related to gold particle size. Higher catalytic activity was found when the gold particles had an average diameter of 3–5 nm; in this range, gold catalysts were more active than the Pt/ZnO/Al₂O₃ catalyst in CO oxidation. Au/ZnO/Al₂O₃ catalyst with small amount of ZnO is more active than Au/Al₂O₃ catalyst due to higher dispersion of gold particles.     

In situ infrared study of formate reactivity on water–gas shift and methanol synthesis catalysts

In order to investigate the methanol synthesis reaction from CO₂/H₂, a comparative study of the reactivity of formate species on different types of catalysts and catalyst supports has been carried out. Formic acid was adsorbed on water–gas shift catalysts, Cu/ZnO/Al₂O₃ methanol synthesis catalyst and ZnO/Al₂O₃ support, Cu/ZnO/ZrO₂ and Cu/ZnO/CeO₂ methanol synthesis catalysts as well as their corresponding supports ZnO/ZrO₂ and ZnO/CeO₂. Superior reactivity and selectivity of dedicated methanol synthesis catalysts was evidenced by their behavior during the subsequent heating ramp, when these samples showed the simultaneous presence of formates and methoxy species and a higher stability of these reaction intermediates in the usual temperature range for the methanol synthesis reaction.     

Physicochemical and Reactivity Studies on Polystyrene‐Cu/Al2O3 Catalysts: An Attempt to Control Copper Dispersion

The influence of coating of 5.0 (w/w%) Cu/γ‐Al₂O₃ catalyst by different ratios of polystyrene on the physicochemical and textural properties was studied. The physicochemical and textural properties of polystyrene‐`Cu/γ‐Al₂O₃ catalysts were investigated by N₂ adsorption, O₂ chemisorption, FTIR, XRD, TEM, and SEM. In addition, the kinetics of H₂O₂ decomposition as a model redox reaction over polymer coated and uncoated catalysts was investigated. The highest activity was achieved by 0.06 wt% polystyrene‐5.0Cu/γ‐Al₂O₃ catalyst. The parent 5.0Cu/γ‐Al₂O₃ catalyst showed auto‐catalytic first order mechanism, which was subjected to a pronounced modification to a simple first order one upon coating by polystyrene. This modification in the mechanism was accompanied with an increase in the apparent activation energy of the reaction. The observed high activity of 0.06 wt% polystyrene‐5.0Cu/γ‐Al₂O₃ catalyst was attributed to the role of polymer in enhancement of the degree of dispersion of the surface copper. However, the modification in kinetics of the reaction was attributed to the difference in the nature of Cu active sites namely, the polymer protected the metallic copper species on the surface of γ‐Al₂O₃ support against possible oxidation to copper sub‐oxides and/or that polymer might change the hydrophilic properties of the reaction media.     

Fe3O4改性的Ru/γ-Al2O3催化剂的原位液相加氢性能

采用分步浸渍法制备负载型Ru-Fe₃O₄/γ-Al₂O₃ 催化剂, 并利用透射电子显微镜(TEM)、X 射线衍射(XRD)、N₂吸附-脱附(BET)、傅里叶变换红外(FTIR)光谱与X射线光电子能谱(XPS)表征催化剂的纳米颗粒粒径分布、晶相组成、表面结构及吸附物种等性质. 将Ru-Fe₃O₄/γ-Al₂O₃催化剂用于3,4-二氯硝基苯选择性原位液相加氢反应, 考察了反应条件对催化活性的影响, 并讨论了不同制备条件下催化剂的稳定性能. 结果表明, 在473 K、液压3 MPa、原料质量分数2%, 乙醇/水体积比75:25 的反应条件下, 3,4-二氯硝基苯的转化率为100%, 3,4-二氯苯胺的选择性高达96.4%. Fe₃O₄含量对催化剂稳定性能有显著影响, 当Ru和Fe 的质量分数分别为2%和6%时, 催化剂可稳定200 h以上. 表面吸附CO与积碳是导致催化剂失活的主要原因, 以Fe₃O₄作为高效的助剂, 进行水汽转换(WGS)反应与费托合成(FTS)可移除CO, 而采用煅烧法去除表面积碳. 晶相变化与纳米颗粒的聚集可能导致催化剂部分失活, 其原因以及再生方法需进一步考察.     

不同硅铝比的MCM-22分子筛的气相硅烷化处理

对不同硅铝比的MCM-22分子筛进行气相硅烷化处理,并采用X射线衍射、固体核磁、N₂吸附-脱附和甲苯吸附等技术对样品进行了表征. 结果显示,原料硅铝比为50~100的MCM-22分子筛均可以利用气相硅烷化,在不脱除骨架铝的基础上,将Si(OH)₂柱撑结构引入其层间超笼系统,从而使层间距增大,孔体积增加; 将密度泛函理论用于计算硅烷化前后的MCM-22分子筛的N₂吸附等温线,成功得到十元环孔道和超笼体系的比表面积和孔体积,发现气相硅烷化使MCM-22分子筛超笼体系的比表面积和孔体积增大,而十元环孔道减小.另外,气相硅烷化可有效提高不同硅铝比MCM-22分子筛的甲苯平衡吸附量.     

Cooperative Effect of Platinum and Alumina on Catalyst Deactivation for Dehydrogenation Reaction

The cooperative effect on catalyst deactivation of Pt-based catalysts for dehydrogenation reaction was investigated using the combination of Pt-based/SiO₂ and Al₂O₃. The presence of the effect was confirmed by reaction test, CO adsorption, H₂-TPD and TPO. Considering conversion, active site, H₂ uptake and the nature and amount of coke, interestingly, the physical mixture of Pt-based catalyst supported on SiO₂ with 100-120 mesh and Al₂O₃ 60-80 mesh was similar to Pt-based Al₂O₃. The concept of combination of two catalytic functions, acidity and metallic species, will certainly provide the possibility of better catalyst design.     

负载型纳米Au/Cr_2O_3催化甘油氧化合成甘油酸

制备了一系列负载型纳米Au/Cr_2O_3催化剂,采用ICP、FTIR、XRD和N2吸附脱附对所制备的催化剂进行了表征.以3%的H_2O_2为氧化剂,考察其对甘油选择性氧化反应的催化性能.结果表明,该类催化剂在甘油选择性氧化反应中表现出了较好的催化性能,其中Au/Cr_2O_3(0.95%)的催化性能最好,甘油转化率可达81.5%,甘油酸选择性为67.0%,且该非均相催化剂重复使用10次后仍保持较高的催化活性.