The effect of temperature on the electrical characteristics of Ti/n-GaAs Schottky diodes

Schottky diodes still attract researchers as they are used in various device applications. This study provides I–V characteristics of Ti/n-GaAs (80–300 K). Higher barrier height (Φ_B0) values were obtained for higher temperatures, whereas the ideality factor exhibited the opposite behavior. This was associated with a barrier inhomogeneity at the Ti/GaAs interface, which has a Gaussian distribution (GD). The mean barrier height values calculated from the modified Richardson and Φ_B0 - q/2 kT plots were found to be 0.584 eV and 0.575 eV in the temperature range of 80–160 K. They were found as 1.041 eV and 1.033 eV between 180 K and 300 K, respectively. The modified Richardson constant value, on the other hand, was calculated as 22.06 A cm⁻² K⁻² (80–160 K) and 13.167 A cm⁻² K⁻² (180–300 K). These values are higher than the theoretical value for n-GaAs, which is 8.16 A cm⁻² K⁻². This difference may stem from intense inhomogeneity at the Ti/n-GaAs interface.     

Metastable helium atom scattering from Ni(1 1 0) surface

The survival probability (SP) of metastable helium atoms (He¹) during scattering from the clean, alkalated and oxygen-adsorbed Ni(1 1 0) surfaces has been examined in the kinetic energy range of 50–400 meV. The measurements were carried out using a time-of-flight technique and a pulsed-discharge type metastable helium atom source. The SP is nearly constant for a kinetic energy (E_kin) of 50–100 meV and decreases exponentially with the increase in E_kin at 100–400 meV. It has been shown that the SP at E_kin=100–400 meV depends on the repulsive part of the He¹-surface interaction potential.     

Rotational structure of CN emission from active nitrogen flames

The CN violet bands from active nitrogen flames have been studied. Rotational line intensities and rotational temperatures have been measured for a number of bands (0–1, 4–6, 5–7, 11-11, 12-12, and 13-13) at pressures ranging from 3 to 30 torr. The bands with ν′ >10show an anomalous rotational intensity distribution, which fits a mixture of two temperatures (one around 1200–3000 K and another near room temperature); bands with ν′<7 show a single temperature of 300–400 K. The relaxation of the high temperature group with pressure yields a relaxation time of the order of 10^?7s for CN molecules in the B-state. Excitation mechanisms for CN(B²σ⁺) are discussed.     

Thermal annealing effects on I–V–T characteristics of sputtered Cr/n-GaAs diodes

Sputtered Cr/n-GaAs Schottky diodes have been prepared and annealed at 200 and 400 °C. The current–voltage (I–V) characteristics of the as-deposited and annealed diodes have been measured in the temperature range of 60–320 K with steps of 20 K. The effect of thermal annealing on the temperature-dependent I–V characteristics of the diodes has been investigated experimentally. The ideality factor and barrier height (BH) values for 400 °C annealed diode approximately remain unchanged from 120 to 320 K, and those of the as-deposited sample from 160 to 320 K. The departures from ideality at low temperatures have been ascribed to the lateral fluctuations of the BH. The BH values of 0.61 and 0.74 eV for the as-deposited and 400 °C annealed diodes were obtained at room temperature, respectively. A Richardson constant value of 9.83 A cm⁻² K⁻² for 400 °C annealed Schottky diode, which is in close agreement with the known value of 8.16 A cm⁻² K⁻² for n-type GaAs. Furthermore, T₀ anomaly values of 15.52, 10.68 and 5.35 for the as-deposited and 200 and 400 °C annealed diodes were obtained from the nT versus T plots. Thus, it has been seen that the interface structure and quality improve by the thermal annealing at 400 °C.     

The vibrational spectrum of thiazole between 600 and 1400 cm revisited: A combined high-resolution infrared and theoretical study

The Fourier transform infrared gas-phase spectrum of thiazole, C₃H₃NS, has been recorded in the 600-1400 cm⁻¹ wavenumber region with a resolution around 0.0030 cm⁻¹. Nine fundamental bands (ν₅(A′) to ν₁₁(A′), ν₁₅(A″), and ν₁₆(A″)) are analysed employing the Watson model. Ground-state rotational and quartic centrifugal distortion constants as well as upper state spectroscopic constants have been obtained from the fits. A detailed analysis of perturbations identified in the ν₁₁(A′) band at 866.5 cm⁻¹ enables a definitive location of the very weak ν₁₀(A′) and ν₁₄(A″) bands at 879.3 and 888.7 cm⁻¹, respectively. The three levels are analysed simultaneously by a model including Coriolis resonance using an ab initio predicted first order c-Coriolis coupling constant; second and higher order Coriolis parameters are determined. Qualitative explanations in terms of Coriolis resonances are given for a number of crossings observed in ν₅(A′), ν₆(A′), and ν₇(A′) at 1383.7, 1325.8, and 1240.5 cm⁻¹, respectively. The rotational constants, anharmonic frequencies, and vibration-rotation constants (alphas, ) calculated by quantum chemical calculations using a cc-pVTZ and TZ2P basis with B3LYP methodology, have been compared with the present experimental data. The rotation constant differences for each vibrational state, from the ground state values, are closer to experiment from the TZ2P calculations relative to those using cc-pVTZ. The values for Δ_J, Δ_JK, Δ_K, δ_J, and δ_K are close to experiment with both basis sets.     

Dynamic scaling hysteresis behavior and field-induced domain transition of 0.16PIN-0.62PMN-0.22 PT single crystals

Due to the good dielectric, piezoelectric and ferroelectric properties, the pseudo-ternary ferroelectric single crystals Pb(In_1/2Nb_1/2)O₃-Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃ (PIN-PMN-PT) have been widely concerned and studied. In this study we found that the dynamic hysteresis loop area <A> with electric field E₀ and frequency f₀ of the 0.16 Pb(In_1/2Nb_1/2)O₃-0.62 Pb(Mg_1/3Nb_2/3)O₃-0.22PbTiO₃ (0.16PIN-0.62PMN-0.22 PT) single crystals satisfies the relational equation <A> ∝ E₀^βf₀^α. In the <A> ∝ E₀^β relationship, both linear stages are found correlated with the low electric field in the first stage E₀<E_c and the high electric field in the third stage E₀ > 3E_c. The hysteresis loop area <A> with frequency f₀ relationship satisfies the equation <A> ∝ f₀^α with roughly linear trend and the hysteresis loop area <A> decreases with increasing frequency f₀. Such electric field dependent dynamic hysteresis scaling can be observed by polarized light microscopy.     

The Lamb-dip spectrum of the J + 1 ← J (J = 0, 1, 3-8) transitions of HCN: The nuclear hyperfine structure due to H, C, and N

The pure rotational J + 1 ← J transitions, with J = 0, 1, 3-8, of H¹³CN have been observed in the millimeter- and submillimeter-wave region using the Lamb-dip technique to resolve the hyperfine structure due to H, ¹³C, and ¹⁴N. The present observations allow us to provide for the first time the spin-rotation constant of ¹³C and the spin-spin interaction constant S₁₂ (between H and ¹³C) as well as to remarkably improve the quadrupole coupling and spin-rotation constants of ¹⁴N. In addition, a good empirical estimation of C_I(H), based on ab initio calculations, has also been provided. Furthermore, our frequencies together with previous data permit to determine the most accurate ground state rotational parameters known up to now.     

Fourier transform emission spectroscopy of the BΣ-XΣ system of CN

The emission spectrum of the B²Σ⁺-X²Σ⁺ system of CN has been observed at high-resolution using a Fourier transform spectrometer. The rotational structure of a large number of bands involving vibrational levels v = 0-15 of both electronic states has been analyzed, and improved spectroscopic constants have been determined by combining the microwave and infrared measurements from previous studies. Improved spectroscopic constants for vibrational levels up to v″ = 18 in the X²Σ⁺ state and v′ = 19 in the B²Σ⁺ state have been determined by combining the measurements of the 16-13, 18-17, 18-18, 19-15, and 19-18 bands of Douglas and Routly [Astrophys. J. Suppl. 1 (1955) 295-318] and 17-14 and 17-16 bands of Ito et al. [J. Chem. Phys. 96 (1992) 4195] with our data. The band constants obtained have been used to estimate equilibrium ground state constants for CN.     

Absolute radical concentration measurements in low-pressure H2/O2 flames during the combustion of graphite

Absolute CN and CH radical concentrations were determined in situ during the combustion of a graphite substrate in premixed, laminar, low-pressure, H₂/O₂ flames for two different equivalence ratios, = 1.0 and = 1.5. For CN measurements, a small amount of NO (1.8%) was added. The concentration of CN was measured by cavity ring-down spectroscopy (CRDS) probing the absorption of the P_1,2 (13) in the B–X (0, 0) band at 388.1 nm, and the concentration of CH was measured by linear unsaturated laser-induced fluorescence (LIF) exciting the fluorescence of the R₁ (4) in the B–X (0, 0) band at 387.4 nm. Temperature measurements were done based on LIF excitation spectra of OH in the A–X (0, 0) band. It was found that the graphite substrate reduces the flame temperature in the vicinity of its surface. The CN concentrations were found to be three times higher for the rich flame than for the stoichiometric flame. CH concentrations were slightly higher for the stoichiometric flame than for the rich flame. The observed CH/CN concentration ratio is substantially lower compared to NO-doped low-pressure CH₄/O₂ flames. The obtained quantitative information can serve as a first calibration point for detailed numerical simulations of the burning solid graphite, which are based on the concept of surface elementary reactions.     

Flame chemistry of tetrahydropyran as a model heteroatomic biofuel

The flame chemistry of tetrahydropyran (THP), a cyclic ether, has been examined using vacuum-ultraviolet (VUV)-photoionization molecular-beam mass spectrometry (PI-MBMS) and flame modeling, motivated by the need to understand and predict the combustion of oxygen-containing, biomass-derived fuels. Species identifications and mole-fraction profiles are presented for a fuel-rich (Φ = 1.75), laminar premixed THP–oxygen–argon flame at 2.66 kPa (20.0 Torr). Flame species with up to six heavy atoms have been detected. A detailed reaction set was developed for THP combustion that captures relevant features of the THP flame quite well, allowing analysis of the dominant kinetic pathways for THP combustion. Necessary rate coefficients and transport parameters were calculated or were estimated by analogies with a recent reaction set [Li et al., Combust. Flame 158 (2011) 2077–2089], and necessary thermochemical properties were computed using the CBS-QB3 method. Our results show that under the low-pressure conditions, THP destruction is dominated by H-abstraction, and the three resulting THP-yl radicals decompose primarily by β-scissions to two- and four-heavy-atom species that are generally destroyed by β-scission, abstraction, or oxidation.     

Sub-Doppler and Doppler spectroscopy of DCN isotopomers in the terahertz region: ground and first excited bending states (v1v2v3)=(0 1 0)

The rotational spectra of the deuterium cyanide isotopic species DCN, D¹³CN, DC¹⁵N, and D¹³C¹⁵N were recorded in the vibrational ground and first excited bending state (v₂=1) up to 2 THz. The R-branch transitions from J=3←2 to J=13←12 were measured with sub-Doppler resolution. These very high resolution (∼70 kHz) and precise (±3-10 kHz) saturation dip measurements allowed for resolving the underlying hyperfine structure due to the ¹⁴N nucleus in DCN and D¹³CN for transitions as high as J=10←9. Additional high JR-branch (J=25←24 to J=28←27) transitions around 2 THz and direct l-type (ΔJ=0, J=19 to J=25) transitions from 66 to 118 GHz were recorded in Doppler-limited resolution. For the ground state of D¹³C¹⁵N, the J=1←0 transition was measured for the first time. The transition frequency accuracies for the other deuterated species were significantly improved. These new experimental data, together with the available infrared rovibrational data and previously measured direct l-type transitions, were subjected to a global least squares analysis for each isotopomer. This yielded precise sets of molecular constants for the ground and first excited vibrational states, including the nuclear quadrupole and magnetic spin-rotation coupling constants of the ¹⁴N nucleus for DCN and D¹³CN. The hyperfine structure due to the D, ¹³C, and ¹⁵N nuclei have not been resolved, but led to a broadening of the observed saturation dips.     

Recombination luminescence of CsI(Tl) under electron pulse irradiation

The luminescence kinetics of CsI(Tl) exposed to an electron pulse irradiation (E_e = 250 keV, t_1/2 = 10 ns, j = 2 ÷ 160 mJ/cm²) has been studied. It has been discovered that the slow emission rise is due to hole V_k–Tl⁰ recombination luminescence at temperature from 100 to 160 K and electron–V_kA recombination, where electrons released from single Tl⁰ at temperature from 180 to 300 K. The effect of Tl concentration on both processes has been investigated.     

Effects of cryogenic temperature on premixed hydrogen/air flame propagation in a closed channel

As a carbon-free fuel, hydrogen has received significant attention recently since it can help enable low-carbon-economy. Hydrogen has very broad flammability range and very low minimum ignition energy, and thereby there are severe safety concerns for hydrogen transportation and utilization. Cryo-compressed hydrogen is popularly used in practice. Therefore, it is necessary to investigate the combustion properties of hydrogen at extremely low or cryogenic temperatures. This study aims to assess and interpret the effects of cryogenic temperature on premixed hydrogen/air flame propagation and acceleration in a thin closed channel. Different initial temperatures ranging from normal temperature (T₀ = 300 K) to cryogenic temperature (T₀ = 100 K) are considered. Both one- and two-dimensional hydrogen/air flames are investigated through transient simulations considering detailed chemistry and transport. It is found that when the initial temperature decreases from T₀ = 300 K to T₀ = 100 K, the expansion ratio and equilibrium pressure both increase substantially while the laminar flame speeds relative to unburned and burned gasses decrease moderately. The one-dimensional flame propagation is determined by laminar flame speed and thereby the combustion duration increases as the initial temperature decreases. However, the opposite trend is found to happen to two-dimensional flame propagation, which is mainly controlled by the flame surface area increase due to the no-slip side wall constraint and flame instability. Based on the change in flame surface area, three stages including the initial acceleration, steady burning and rapid acceleration are identified and investigated. It is demonstrated that the large expansion ratio and high pressure rise at cryogenic temperatures can significantly increase the flame surface area in early stage and promote both Darrieus-Landau instability (hydrodynamic instability) and Rayleigh-Taylor instability in later stage. These two instabilities can substantially increase the flame surface area and thereby accelerate flame propagation in hydrogen/air mixtures at cryogenic temperatures. The present study provides useful insights into the fundamental physics of hydrogen flames at extremely low temperatures, and is closely related to hydrogen safety.     

Stabilized flames in hybrid aluminum-methane-air mixtures

A premixed methane–air bunsen-type flame is seeded with micron-sized (d₃₂ = 5.6 μm) atomized aluminum powder over a wide range of solid fuel concentrations. The burning velocities of the resulting two-phase hybrid flame are determined using the total surface area of the inner flame cone and the known volumetric flow rate, and spatially resolved flame spectra are obtained with a spectral scanning system. Flame temperatures are derived through polychromatic fitting of Planck’s law to the continuous part of the spectrum. It is found that an increase in the solid fuel concentration changes the aluminum combustion regime from low temperature oxidation to full-fledged flame front propagation. For stoichiometric methane–air mixtures, the transition occurs in the aluminum concentration range of 140–220 g/m³ and is manifested by the appearance of AlO sub-oxide bands and an increase in the flame temperature to 2500 K. The flame burning velocity is found to decrease only slightly with an increase in aluminum concentration, in contrast to the rapid decrease in flame speed, followed by quenching, that is observed for flames seeded with inert SiC particles. The observed behavior of the burning velocity and flame temperature leads to the conclusion that intense aluminum combustion in a hybrid flame only occurs when the flame front propagating through the aluminum suspension is coupled to the methane–air flame.     

Poly(3-methylthiophene)-based porous silicon substrates as a urea-sensitive electrode

Poly(3-methylthiophene) (P3MT)-based porous silicon (PS) substrates were fabricated and characterized by cyclic voltammetry, scanning electron microscopy, and auger electron spectroscopy. After doping urease (Urs) into the polymeric matrix, sensitivity and physicochemical properties of the P3MT-based PS substrate was investigated compared to planar silicon (PLS) and bulk Pt substrates. PS substrate was formed by electrochemical anodization in an etching solution composed of HF, H₂O, and ethanol. Subsequently, Ti and Pt thin-films were sputtered on the PS substrate. Effective working electrode area (A_eff) of the Pt-deposited PS substrate was determined from a redox reaction of Fe(CN)₆³⁻/Fe(CN)₆⁴⁻ redox couple in which nearly reversible cyclic voltammograms were obtained. The i_p versus v^1/2 plots showed that A_eff of the PS-based Pt thin-film electrode was 1.62 times larger than that of the PLS-based electrode.Electropolymerization of P3MT on both types of electrodes were carried out by the anodic potential scanning under the given potential range. And then, urease molecules were doped to the P3MT film by the chronoamperometry. Direct electrochemistry of a Urs/P3MT/Pt/Ti/PS electrode in an acetonitrile solution containing 0.1 mol/L NaClO₄ was introduced compared to a P3MT/Pt/Ti/PS electrode at scan rates of 10 mV s⁻¹, 50 mV s⁻¹, and 100 mV s⁻¹.Amperometric sensitivity of the Urs/P3MT/Pt/Ti/PS electrode was ca. 1.67 μA mM⁻¹ per projected unit square centimeter, and that of the Urs/P3MT/Pt/Ti/PLS electrode was ca. 1.02 μA mM⁻¹ per projected unit square centimeter in a linear range of 1-100 mM urea concentrations. 1.6 times of sensitivity increase was coincident with the results from cyclic voltammetrc analysis.Surface morphology from scanning electron microscopy (SEM) images of Pt-deposited PS electrodes before and after the coating of Urs-doped P3MT films showed that pore diameter and depth were 2 μm and 10 μm, respectively. Multilayered-film structures composed of metals and organics for both electrodes were also confirmed by auger electron spectroscopy (AES) depth profiles.     

Annealing effects on the crystal structure and physical properties of FeSe1−xTex (0.6 ≦ x ≦ 1) single crystals

Annealing effects of FeSe_1?xTe_x (0.6 ≦ x ≦ 1) single crystals have been investigated from measurements of the powder X-ray diffraction and specific heat. Through the annealing, several peaks of powder X-ray diffraction have become sharp and a clean jump of the specific-heat at the superconducting (SC) transition temperature, T_c, has been observed for x = 0.6–0.9, indicating bulk superconductivity. For annealed single-crystals of x = 0.6–0.8, the SC condensation energy, U₀, and the SC gap, Δ₀, at 0 K have been estimated as ～1.8 J/mol and 2.3–2.5 meV, respectively. The value of 2Δ₀/k_BT_c is 3.9–4.5, indicating a little strong-coupling superconductivity. Both the electronic specific-heat coefficient in the normal state, γ_n, and the residual electronic specific-heat coefficient in the SC state, γ₀, have been found to show significant x dependence. The values of γ_n are much larger than those estimated from the band calculation.     

Analysis of the current-transport mechanism across a CVD diamond/silicon interface

This work presents a study on the mechanism of injection and charge transport through a CVD diamond/n⁺-Si interface. The current-voltage-temperature characteristics of CVD diamond/silicon heterojunctions measured in the temperature range 119-400 K have been interpreted according to thermionic theory and thermionic field-emission theory. This junction shows deviations from the ideal thermionic theory current model, suggesting the presence of surface states, thin-layer depletion and/or non-homogeneity in the diamond/silicon interface. The T₀ anomaly has been used to explain the behaviour of the ideality factor with temperature. At very low temperatures tunnelling may occur because the E₀₀ values for these junctions are close to the value expected by thermionic field-emission theory. The usual activation-energy plot deviates from linearity at low temperatures. This deviation has been corrected supposing a ln(J_S/T²) versus 10³/nT plot. Under these conditions the Richardson constant is found to be 0.819 A cm⁻² K⁻², which is close to the theoretical value of 1.2 A cm⁻² K⁻². Field-emission device is a promising application for diamond/silicon structure.     

Improved electrical parameters of vacuum annealed Ni/4H-SiC (0 0 0 1) Schottky barrier diode

The reported work has been focused on the improvement of electrical parameters of Schottky diode using vacuum annealing at mild temperature in Ar gas ambient. Nickel Schottky barrier diodes were fabricated on 50 μm epitaxial layer of n-type 4H-SiC (0 0 0 1) substrate. The values of leakage current, Schottky barrier height (?_B), ideality factor (η) and density of interface states (N_SS) were obtained from experimentally measured current–voltage (I–V) and capacitance–voltage (C–V) characteristics before and after vacuum annealing treatment. The data revealed that ?_B, η and reverse leakage current for the as-processed diodes are 1.25 eV, 1.6 and 1.2 nA (at ?100 V), respectively, while for vacuum annealed diodes these parameters are 1.36 eV, 1.3 and 900 pA (at same reverse voltage). Improved characteristics have been resulted under the influence of vacuum annealing because of lesser number of minority carrier generation due to incessant reduction of number of available discrete energy levels in the bandgap of 4H-SiC substrate and lesser number of interface states density at Ni/4H-SiC (0 0 0 1) interface.     

Critical temperature and reactant mass flux for radiative extinction of ethylene microgravity spherical diffusion flames at 1 bar

In microgravity combustion, where buoyancy is not present to accelerate the flow field and strain the flame, radiative extinction is of fundamental importance, and has implications for spacecraft fire safety. In this work, the critical point for radiative extinction is identified for normal and inverse ethylene spherical diffusion flames via atmospheric pressure experiments conducted aboard the International Space Station, as well as with a transient numerical model. The fuel is ethylene with nitrogen diluent, and the oxidizer is an oxygen/nitrogen mixture. The burner is a porous stainless-steel sphere. All experiments are conducted at constant reactant flow rate. For normal flames, the ambient oxygen mole fraction was varied from 0.2 to 0.38, burner supply fuel mole fraction from 0.13 to 1, total mass flow rate, ṁ_total, from 0.6 to 12.2 mg/s, and adiabatic flame temperature, T_ad, from 2000 to 2800 K. For inverse flames, the ambient fuel mole fraction was varied from 0.08 to 0.12, burner supply oxygen mole fraction from 0.4 to 0.85, ṁ_total from 2.3 to 11.3 mg/s, and T_ad from 2080 to 2590 K. Despite this broad range of conditions, all flames extinguish at a critical extinction temperature of 1130 K, and a fuel-based mass flux of 0.2 g/m²-s for normal flames, and an oxygen-based mass flux of 0.68 g/m²-s for inverse flames. With this information, a simple equation is developed to estimate the flame size (i.e., location of peak temperature) at extinction for any atmospheric-pressure ethylene spherical diffusion flame given only the reactant mass flow rate. Flame growth, which ultimately leads to radiative extinction if the critical extinction point is reached, is attributed to the natural development of the diffusion-limited system as it approaches steady state and the reduction in the transport properties as the flame temperature drops due to increasing flame radiation with time (radiation-induced growth.)