Polymer hybrids with functionalized silsesquioxanes via two physical interactions in one system

Transparent and homogeneous polymer hybrids were obtained from a series of random styrene/N,N‐dimethylacrylamide copolymers (PSnPAm) and octa(3‐hydroxypropyldimethylsiloxy)octasilsesquioxane (Cube‐OH) by means of the sol–gel reaction of phenyltrimethoxysilane (PTMOS). The resulting ternary polymer hybrids were prepared via two simultaneous physical interactions [hydrogen‐bonding and aromatic (π–π) interactions] in one system. Cube‐OH and PTMOS were used to form hydrogen‐bonding and aromatic (π–π) interactions, respectively, with the organic copolymer. When PS90PA10 was used as an organic polymer for the two physical interactions, the transparency was maintained when the weight ratio of Cube‐OH to PTMOS was increased to 0.5. However, the polymer hybrids with PS65PA35 produced optically translucent or turbid materials, which indicated the phase separation of the organic polymer and silica gel. The homogeneity of the ternary polymer hybrids was dependent on the balance between the intensity of the hydrogen‐bonding interaction and that of the aromatic (π–π) interaction. The homogeneity was supported by the results of Fourier transform infrared, differential scanning calorimetry, scanning electron microscopy, and X‐ray diffraction, which demonstrated a nanometer‐level integration of the organic polymer, Cube‐OH, and silica gel. The initial decomposition temperature of the ternary polymer hybrids was more dependent on the amount of PTMOS than on that of Cube‐OH. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1306–1315, 2003     

Preparation and characterization of some unusually transparent poly(dimethylsiloxane) nanocomposites

A technique was developed for preparing poly(dimethylsiloxane) nanocomposites having unusually high transparencies as quantitatively judged by ultraviolet–visible spectroscopy. The method was the in situ generation of silica particles by a two‐step sol–gel procedure in which the required water of hydrolysis was simply absorbed from the air, and the catalyst was generated in situ from a tin salt. Electron microscopy showed that the phase‐separated silica domains were very small (30–50 nm in diameter) and well dispersed, as expected from the transparency of the composites. Stress‐strain measurements in tension indicated that the particles provide very good reinforcement. Ultra‐small‐angle X‐ray scattering data showed that the domain morphology depends strongly on catalyst, but weakly on loading level. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1897–1901, 2003     

Acrylic polymer/silica hybrids prepared by emulsifier‐free emulsion polymerization and the sol–gel process

Acrylic polymer/silica hybrids were prepared by emulsifier‐free emulsion polymerization and the sol–gel process. Acrylic polymer emulsions containing triethoxysilyl groups were synthesized by emulsifier‐free batch emulsion polymerization. The acrylic polymer/silica hybrid films prepared from the acrylic polymer emulsions and tetraethoxysilane (TEOS) were transparent and solvent‐resistant. Atomic force microscopy studies of the hybrid film surface suggested that the hybrid films did not contain large (e.g., micrometer‐size) silica particles, which could be formed because of the organic–inorganic phase separation. The Si? O? Si bond formed by the cocondensation of TEOS and the triethoxysilyl groups on the acrylic polymer increased the miscibility between the acrylic polymer component and the silica component in the hybrid films, in which the nanometer‐size silica domains (particles) were dispersed homogeneously in the acrylic polymer component. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 273–280, 2006     

Miscibility and properties of polyurethane/benzyl starch semi‐interpenetrating polymer networks

We successfully prepared a series of transparent materials with semi‐interpenetrating polymer networks (semi‐IPNs) from castor‐oil‐based polyurethane (PU) and benzyl starch (BS). The miscibility, morphology, and properties of the semi‐IPN films were investigated with attenuated total reflection/Fourier transform infrared spectroscopy, differential scanning calorimetry, dynamic mechanical thermal analysis, scanning electron microscopy, wide‐angle X‐ray diffraction, electron spin resonance (ESR), ultraviolet–visible spectroscopy, and tensile testing. The results revealed that the semi‐IPN films had good or certain miscibility with BS concentrations of 5–70 wt % because of the strong intermolecular interactions between PU and BS. With an increase in the concentration of BS, the tensile strength and Young's modulus of the semi‐IPN materials increased. The ESR data confirmed that the segment volume of PU in the semi‐IPNs increased with the addition of BS; that is, the chain stiffness increased as a result of strong interactions between PU and BS macromolecules. It was concluded that starch derivatives containing benzyl groups in the side chains more easily penetrated the PU networks to form semi‐IPNs than those containing aliphatic groups, and this led to improved properties. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 603–615, 2005     

Preparation and properties of poly(styrene-co-maleic anhydride)/silica hybrid materials by the in situ sol–gel process

Poly(styrene-co-maleic anhydride)/silica hybrid material has been successfully prepared from styrene–maleic anhydride copolymer and tetraethoxysilane (TEOS) in the presence of a coupling agent (3-aminopropyl)triethoxysilane (APTES) by an in situ sol–gel process. It was observed that the gel time of sol–gel solution was dramatically influenced by the amount of APTES. The hybrid material exhibits optical transparency almost as good as both silica gel and the copolymer. The covalent bonds between organic and inorganic phases were introduced by the aminolysis reaction of the amino group with maleic anhydride units of copolymer to form a copolymer bearing trimethoxysilyl groups, which undergo hydrolytic polycondensation with TEOS. The differential scanning calorimetry (DSC) showed that the glass transition temperature of the hybrid materials increases with increasing of SiO₂ composition. Photographs of scanning electron microscopy (SEM) and atomic force microscopy (AFM) inferred that the size of the inorganic particles in the hybrid materials was less than 20 nm. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1607–1613, 1998     

Inorganic–organic hybrids involving poly(ε‐caprolactone) and silica network: Hydrogen‐bonding interactions and isothermal crystallization kinetics

Inorganic–organic hybrids mediated by hydrogen‐bonding interactions involving silicon oxide network and poly(ε‐caprolactone) (PCL) were prepared via an in situ sol–gel process of tetraethoxysilane in the presence of PCL. Fourier transform infrared spectroscopy indicated that there were hydrogen‐bonding interactions between carbonyls of PCL and silanol hydroxyls that were formed by incomplete polycondensation in the sol–gel process. In terms of the frequency shift of the hydroxyl stretching vibration bands, it is concluded that the strength of the interassociation between PCL and silicon oxide networks is weaker than that of the self‐association in the control silica network. The phenomenon of equilibrium melting point depression was observed for the PCL/silica system. The hybridization of PCL with silica network causes a considerable increase in the overall crystallization rate and dramatically influences the mechanism of nucleation and growth of the PCL crystallization. The analysis of isothermal crystallization kinetic data according to the Hoffman‐Lauritzen theory shows that with increasing silica content in the hybrids, the surface energy of extremity surfaces increases dramatically for the hybrids. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2594–2603, 2005     

Flame‐retardant epoxy resins: An approach from organic–inorganic hybrid nanocomposites

Phosphorus‐containing epoxy‐based epoxy–silica hybrid materials with a nanostructure were obtained from bis(3‐glycidyloxy)phenylphosphine oxide, diaminodiphenylmethane, and tetraethoxysilane in the presence of the catalyst p‐toluenesulfonic acid via an in situ sol–gel process. The silica formed on a nanometer scale in the epoxy resin was characterized with Fourier transform infrared, NMR, and scanning electron microscopy. The glass‐transition temperatures of the hybrid epoxy resins increased with the silica content. The nanometer‐scale silica showed an enhancement effect of improving the flame‐retardant properties of the epoxy resins. The phosphorus–silica synergistic effect on the limited oxygen index (LOI) enhancement was also observed with a high LOI value of 44.5. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 986–996, 2001     

Effect of incorporated CdS nanoparticles on the crystallinity and morphology of poly(styrene‐b‐ethylene oxide) diblock copolymers

Surface‐modified CdS nanoparticles selectively dispersed in hexagonally packed poly(ethylene oxide) (PEO) cylinders of poly(styrene‐b‐ethylene oxide) (PSEO) block copolymers were prepared. The photoluminescence and ultraviolet–visible characteristics of the presynthesized CdS nanoparticles in N,N‐dimethylformamide and in PEO domains of the PSEO block copolymers were determined. Because of strong interactions between the CdS nanoparticles and PEO chains, as shown by Fourier transform infrared spectroscopy, the incorporation of the CdS nanoparticles prevented the PEO cylinders from properly crystallizing; this was confirmed by differential scanning calorimetry and wide‐angle X‐ray diffraction measurements. The intercylinder distance between the swollen and reduced‐crystallinity CdS/PEO cylinders in turn increased, as confirmed by small‐angle X‐ray scattering and transmission electron microscopy. At a high CdS concentration (43 wt % or 8.3 vol % with respect to PEO), however, the hexagonally packed cylindrical nanostructure of the PSEO diblock copolymers was destroyed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1220–1229, 2005     

Poly(γ‐glutamic acid)/Silica Hybrids with Calcium Incorporated in the Silica Network by Use of a Calcium Alkoxide Precursor

Current materials used for bone regeneration are usually bioactive ceramics or glasses. Although they bond to bone, they are brittle. There is a need for new materials that can combine bioactivity with toughness and controlled biodegradation. Sol‐gel hybrids have the potential to do this through their nanoscale interpenetrating networks (IPN) of inorganic and organic components. Poly(γ‐glutamic acid) (γ‐PGA) was introduced into the sol‐gel process to produce a hybrid of γ‐PGA and bioactive silica. Calcium is an important element for bone regeneration but calcium sources that are used traditionally in the sol‐gel process, such as Ca salts, do not allow Ca incorporation into the silicate network during low‐temperature processing. The hypothesis for this study was that using calcium methoxyethoxide (CME) as the Ca source would allow Ca incorporation into the silicate component of the hybrid at room temperature. The produced hybrids would have improved mechanical properties and controlled degradation compared with hybrids of calcium chloride (CaCl₂), in which the Ca is not incorporated into the silicate network. Class II hybrids, with covalent bonds between the inorganic and organic species, were synthesised by using organosilane. Calcium incorporation in both the organic and inorganic IPNs of the hybrid was improved when CME was used. This was clearly observed by using FTIR and solid‐state NMR spectroscopy, which showed ionic cross‐linking of γ‐PGA by Ca and a lower degree of condensation of the Si species compared with the hybrids made with CaCl₂ as the Ca source. The ionic cross‐linking of γ‐PGA by Ca resulted in excellent compressive strength and reduced elastic modulus as measured by compressive testing and nanoindentation, respectively. All hybrids showed bioactivity as hydroxyapatite (HA) was formed after immersion in simulated body fluid (SBF).     

Cross‐linking emulsion copolymerization of butyl acrylate with diallyl maleate

The emulsion copolymerization of butyl acrylate (BA) with a trifunctional cross‐linker, diallyl maleate (DAM), was investigated. The effect of the monomer feeding time and the amount of cross‐linker on the microstructural properties (branching, cross‐linking, gel formation, and sol MWD) of the seeded semicontinuous emulsion copolymerization of BA with DAM was investigated. It was found that the gel content was not significantly affected by increasing feeding time, but the level of quaternary carbons (an indication of the branching density) increased. On the other hand, increasing the amount of DAM in the feed composition caused gel content, level of quaternary carbons, and the cross‐linking density to increase. Interestingly, the level of quaternary carbons and the cross‐linking density sharply increased during the cooking period. The molecular weight of the sol decreased as DAM increased in the feed. In addition, the effect of process type, batch versus semibatch, was also considered and important differences in the level of quaternary carbons, cross‐linking, and gel content were found. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4684–4694, 2005     

Nanocomposites of vinyl chloride–acrylonitrile copolymer and silica

Vinyl chloride–acrylonitrile (VC–AN) copolymer was synthesized through emulsion copolymerization. VC–AN copolymer/silica nanocomposites were prepared by solution blending of copolymer and silica in a common solvent, N,N‐dimethylformamide (DMF). The rheology studies show that the shear‐thinning behavior of the VC–AN copolymer solution becomes less distinct as nano particles are introduced. It was also found that the viscosity of the copolymer solution decreases with adding small amount of nano particles. Transmission electron microscopy observations indicate that the UV‐treated silica could disperse well in the copolymer matrix. Differential scanning calorimeter studies suggest that the presence of the silica suppresses crystallization of the AN segments in the copolymers. Because of the interactions between copolymer chains and inorganic particles, the thermal stability and mechanical strength of the VC–AN copolymers are improved considerably. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3127–3134, 2005     

Hydrophilic nanocomposites based on polyurethane/poly(2‐hydroxyethyl methacrylate) semi‐IPNs and modified/unmodified nanosilica for biomedical applications

Nanocomposites based on sequential semi‐interpenetrating polymer network (semi‐IPN) of cross‐linked polyurethane and linear poly(2‐hydroxyethyl methacrylate) with 0.25 and 3 wt % of nanosilica filler were prepared and investigated. The unmodified silica, carboxyl‐modified, and amino‐modified silica were used in an attempt to control the microphase separation of the polymer matrix by polymer–filler interactions. A variety of experimental techniques were used to study morphology, thermal transitions, mechanical properties, and polymer dynamics of the nanocomposites. Special attention was paid to the investigation of the hydration properties of the nanocomposites in the perspective of biomedical applications. The results show that the good hydration properties of the semi‐IPN matrix are preserved in the nanocomposites. Effects of water on polymer dynamics were found to be particularly pronounced for the secondary β_sw,_PHEMA and the β_PU relaxations, in agreement with interpretations in terms of hydrogen bonding interactions with specific groups in the structure of the two polymers. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 397–408     

Copolymers of 2,5‐bis[(4‐methoxyphenyl) oxycarbonyl]styrene with n‐butyl acrylate: Design,synthesis, and characterization

A series of rod–coil diblock copolymers, consisting of poly{2,5‐bis[(4‐methoxyphenyl)oxycarbonyl]styrene} as a rigid segment and poly(n‐butyl acrylate) as a flexible part, were successfully prepared through two inverse procedures by atom transfer radical polymerization. The copolymers were characterized by ¹H NMR and gel permeation chromatography and had high molecular weights and relatively narrow polydispersities (polydispersity index < 1.20). All the block copolymers synthesized had two distinct glass‐transition temperatures according to differential scanning calorimetry. A polarizing optical microscopy investigation demonstrated the liquid crystallinity of the diblock copolymers. The self‐assembly behaviors in dilute solutions was studied by transmission electron microscopy. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5935–5943, 2005     

Dependence of silica particle sizes on network chain lengths,silica contents,and catalyst concentrations in in situ‐reinforced polysiloxane elastomers

Poly(dimethylsiloxane) networks were prepared by tetrafunctionally end‐linking hydroxyl‐terminated chains with tetraethoxysilane (TEOS). Molecular composites were then prepared by in situ sol–gel reactions on additional TEOS swelled into the networks, resulting in the formation of reinforcing silica fillers within the host elastomers. The amount of filler generated generally increased linearly with an increase in the TEOS swelling ratio, as expected. The silica particles formed were examined by small‐angle X‐ray scattering. Of particular interest were the relationships between particle size and molecular weight M_c of the network chains (mesh sizes), amount of filler introduced, and catalyst concentration. Particle sizes were smallest for the smallest values of M_c, possibly demonstrating constraining effects from the very short network chains. At fixed M_c and filler concentrations, higher catalyst concentrations gave larger particles. Increase in filler concentration generally had little effect on particle size at low and high loadings, but markedly increased sizes at intermediate levels (10–20 wt %), presumably caused by coalescence of the scattering entities into considerably larger aggregates. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1421–1427, 1999     

Discussion of substantially identical gel points among multiallyl monomers based on characterization of resultant network polymer precursors consisting of oligomeric primary polymer chains

No difference in the actual gel points was substantially observed among three isomeric diallyl phthalates such as diallyl phthalate (DAP), diallyl isophthalate, and diallyl terephthalate (DAT); this interesting gelation behavior was discussed further in terms of the correlation between gelation and the difference in cyclization modes, and also, the difference in reactivity between the uncyclized and cyclized radicals for cross‐linking. In the present work, we tried to extend the preceding discussion to the polymerization of triallyl trimellitate (TAT) because the molecular structure of TAT is presumed to essentially involve the characteristics of three isomeric diallyl phthalates and, therefore, the enhanced gelation was expected in TAT polymerization. However, no enhancement of gelation was observed. For a full understanding of the gelation in multiallyl cross‐linking polymerization, we explored further the polymerizations of DAP, DAT, and TAT, especially focusing on the characterization of resultant network polymer precursors (NPPs) using SEC‐MALLS‐viscometry providing the correlation of [η] versus M_w of fractionated samples. Notably, the structure of NPP consisting of oligomeric primary polymer chains generated from specific allyl polymerization would become core‐shell type dendritic with the progress of polymerization. The correlation between delayed gelation and decreased reactivity of dendritic NPP for intermolecular cross‐linking is discussed. Conclusively, the reactivity for intermolecular cross‐linking between NPPs decreased with the progress of polymerization leading to a delayed gelation. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2871–2881, 2009     

Organic–inorganic hybrid materials. I. Characterization and degradation of poly(imide–silica) hybrids

Poly(imide–silica) hybrid materials with covalent bonds were prepared by (3-aminopropyl)methyldiethoxysilane (APrMDEOS) terminated amic acid, water, and tetramethoxysilane (TMOS) via a sol–gel technique. Infrared (IR), ²⁹Si and ¹³C CP/MAS nuclear magnetic resonance (NMR) spectroscopy, and thermogravimetric analysis (TGA) were used to study hybrids containing various proportions of TMOS and hydrolysis ratios. The microstructure and chain mobility of hybrids were investigated by proton spin–spin relaxation T₂ measurements. The apparent activation energy E_a for degradation of hybrids in air was studied by the van Krevelen method. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2275–2284, 1999     

Functionalization of carbon nanofibers (CNFs) through atom transfer radical polymerization for the preparation of poly(tert‐butyl acrylate)/CNF materials: Spectroscopic,thermal, morphological,and physical characterizations

Vapor‐grown carbon nanofibers (CNFs) were oxidized and functionalized for atom transfer radical polymerization (ATRP) of tert‐butyl acrylate (t‐BA) from the surface of the CNFs. The materials were characterized by solubility tests, Fourier‐transform infrared (FTIR) spectroscopy, Raman spectroscopy, thermogravimetric analysis (TGA), X‐ray diffraction (XRD), and scanning electron microscopy. The FTIR and electron microscopy results suggest that ATRP process was successfully used to graft poly(tert‐butyl acrylate) (poly(t‐BA)) chains from the surface of the fibers. Raman results strongly indicate the partial degradation of the graphitic layer of CNFs because of the chemical treatments. TGA results suggest that the presence of poly(t‐BA) leads to a decrease of the initial degradation temperature of the fibers. XRD and electron microscopy results indicate that the microstructure of fibers was not destroyed because of the oxidation and functionalization processes. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3326–3335, 2008     

Homogeneous anionic PPE hybrids with silica gel

Anionic poly(p‐phenylene‐ethynylene) (PPE) incorporated polymer hybrids were synthesized from the PPE and tetramethoxysilane together with the organic polymers such as poly(vinylpyrrolidone) via a sol–gel method. Up to 10 wt % of the anionic PPE could be dispersed homogeneously in the resulting polymer hybrid matrix. The obtained polymer hybrids exhibited controllable photoluminescence properties by the modification of the internal environment of organic–inorganic polymer hybrids by changing the organic/inorganic ratios. The photoluminescence of the anionic PPE surrounded by the polymer hybrid matrix was reinforced against the thermal irradiation. Moreover, the photoluminescence of the obtained organic–inorganic polymer hybrids was also tuned by utilizing ionic interactions between the anionic PPE and the inorganic matrix. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3749–3755, 2008     

Temperature‐responsive “tadpole‐shaped” protein–polymer hybrids and their self‐assembly behavior

The temperature‐responsive poly (N, N‐diethylacrylamide) (pDEAAm) with narrower molecular weight distribution was prepared by the atom transfer radical polymerization and characterized by ¹HNMR and gel permeation chromatography. The temperature‐responsive “tadpole‐shaped” BSA–pDEAAm hybrids were fabricated via a free Cys‐34 residue of bovine serum albumin (BSA) site specifically binding to the end group disulfide bonds of pDEAAm and characterized by native‐polyacrylamide gel electrophoresis (Native‐PAGE) and matrix‐assisted laser desorption/ionization time of flight mass spectrometry. Their temperature‐responsive behaviors were measured by ultraviolet‐visible spectra (UV‐Vis). The lower critical solution temperature (LCST) of the pDEAAm was identified as 28°C, and the LCST of BSA–pDEAAm hybrids was identified as 31°C. The morphologies of BSA–pDEAAm hybrids self‐assembled in the aqueous solutions with two different temperatures at 25 °C and 40°C were investigated by transmission electron microscopy. Below the LCST of BSA–pDEAAm hybrids, the separate spherical nanoparticles were observed. In contrast, bundles and clusters were observed above the LCST of BSA–pDEAAm hybrids. The results suggested that the self‐assembly morphology of BSA–pDEAAm hybrids depended upon the pDEAAm block in BSA–pDEAAm hybrids, and the morphology transitions were effected by the LCST of BSA–pDEAAm hybrids. It would be expected to be used in biomedicine and materials science. Copyright © 2016 John Wiley & Sons, Ltd.     

Synthesis of gold–poly(methyl methacrylate) core–shell nanoparticles by surface‐confined atom transfer radical polymerization at elevated temperature

Surface‐confined atom transfer radical polymerization was used to prepare gold nanoparticle–poly(methyl methacrylate) core–shell particles at elevated temperature. First, gold nanoparticles were prepared by the one‐pot borohydride reduction of tetrachloroaurate in the presence of 11‐mercapto‐1‐undecanol (MUD). MUD‐capped gold nanoparticles were then exchanged with 3‐mercaptopropyltrimethoxysilane (MPS) to prepare a self‐assembled monolayer (SAM) of MPS on the gold nanoparticle surfaces and subsequently hydrolyzed with hydrochloric acid. The extent of exchange of MUD with MPS was determined by NMR. The resulting crosslinked silica‐primer layer stabilized the SAM of MPS and was allowed to react with the initiator [(chloromethyl)phenylethyl] trimethoxysilane. Atom transfer radical polymerization was conducted on the Cl‐terminated gold nanoparticles with the CuCl/2,2′‐bipyridyl catalyst system at elevated temperature. The rates of polymerization with the initiator‐modified gold nanoparticles exhibited first‐order kinetics with respect to the monomer, and the number‐average molecular weight of the cleaved graft polymer increased linearly with the monomer conversion. The presence of the polymer on the gold nanoparticle surface was identified by Fourier transform infrared spectroscopy and transmission electron microscopy. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3631–3642, 2005