Origin of the X‐ray magnetic circular dichroism at the L‐edges of the rare‐earths in RxR1−x′Al2 systems

An X‐ray magnetic circular dichroism (XMCD) study performed at the rare‐earth L_2,3‐edges in the R_xR_1?x′Al₂ compounds is presented. It is shown that both R and R′ atoms contribute to the XMCD recorded at the L‐edges of the selected rare‐earth, either R or R′. The amplitude of the XMCD signal is not directly correlated to the magnetization or to the value of the individual (R, R′) magnetic moments, but it is related to the molecular field acting on the rare‐earth tuned in the photoabsorption process. This result closes a longstanding study of the origin of the XMCD at the L‐edge of the rare‐earths in multi‐component systems, allowing a full understanding of the exact nature of these signals.     

Energies and relative intensities of Kα3 and Kα4 x‐ray satellites of sulfur and sulfides by photon excitation

Energies and relative intensities of the K x‐ray satellites K_α4 and K_α3 of sulfur and two sulfides K₂S and FeS are measured by a wavelength dispersive spectrometer. The energy shifts of these satellites relative to the diagram line are compared with Dirac–Fock theoretical values. The energy shifts and relative intensities are examined for chemical effects. Supplementing the present data to the available data, Z dependence of K_α4/K_α3 intensity ratio is studied in the low Z region. Copyright © 2007 John Wiley & Sons, Ltd.     

Kβ/Kα x‐ray intensity ratios for bromine and iodine compounds

Kβ/Kα x‐ray intensity ratios of some Br and I compounds were studied. The samples were excited by 59.5 keV γ‐rays emitted from an Am‐241 radioisotope source and characteristic K x‐rays emitted from the samples were counted by means of an Si(Li) detector which has a resolution 155 eV at 5.9 keV. The experimental values were compared with the calculated theoretical values for elemental Br and I. Copyright © 2003 John Wiley & Sons, Ltd.     

A gas proportional‐scintillation counter for x‐ray spectrometry in the 0.1–3 keV range

Results for the energy resolution of a uniform‐field gas proportional‐scintillation counter are presented for the range 0.1–3 keV. A comparison with results from the literature shows that the detector is most suitable for this energy range. Examples of x‐ray fluorescence pulse‐height distributions from geological and industrial samples are presented. Copyright © 2004 John Wiley & Sons, Ltd.     

Literature trends in x‐ray emission spectrometry in the period 1990–2000–a review

A quantitative overview is given of the role that x‐ray emission analysis methods, in their various forms, play in the literature for the period from January 1990 to the end of December 2000. The major sources of information were computerized searches through Chemical Abstracts and Web of Science and, specifically for 1998, a manual search through Analytical Abstracts. Areas that are covered in this review pertain to the recent trends in x‐ray emission spectrometry in general and in some specific techniques such as x‐ray fluorescence analysis, synchrotron radiation‐induced and particle‐induced x‐ray emission, total‐reflection and micro‐x‐ray fluorescence analysis. A brief outline of recent developments in the specific fields is given, with emphasis on the various excitation and detection modes, on different application areas and on relative contributions of different countries and languages to the x‐ray emission spectrometry literature. It appears that environmental monitoring and research continue to be particularly important publication fields for x‐ray spectrometry. Copyright © 2003 John Wiley & Sons, Ltd.     

Raman spectral studies of Zr4+‐rich BaZrxTi1−xO3(0.5⩽x⩽1.00) phase diagram

This paper reports a systematic study of the composition and the temperature‐dependent‐Raman spectra of Zr⁴⁺‐rich BaZr_xTi_1−xO₃ (BZT) ceramic compositions (0.50⩽x⩽1.00). On the basis of the dielectric behavior of Zr rich BZT ceramics, the observed relaxor behavior has been hypothesized as a result of increasing long‐range interactions of nanosized, Ti⁴⁺‐rich polar regions in a Zr⁴⁺‐rich nonpolar matrix. Beyond an optimum concentration of BaTiO₃ (BT) in the nonpolar matrix of BaZrO₃ (x⩽0.75), a critical size and density of the polar regions is reached when the polar clusters start showing the relaxor like behavior, which finally show classical relaxor behavior for compositions with x = 0.5 and 0.6. This hypothesis is strongly supported from the Raman data on Zr‐rich BZT presented in this paper. Well‐defined BT Raman spectra for 5% BT in BZT composition were recorded, which followed completely up to the 50% Ti addition in the BZT samples. The temperature‐dependent Raman spectra collected on the BZT ceramics far beyond the dielectric transition temperatures supported the existence of the nano‐polar BT regions, like in typical relaxor samples. The full width at half‐maximum (FWHM), integrated intensity of the peaks in the Raman spectra has been analyzed to further support the conclusions. Copyright © 2008 John Wiley & Sons, Ltd.     

Laboratory vacuum spectrometer for the soft x‐ray region

A laboratory surface x‐ray absorption near edge structure ((S)XANES) spectrometer used for measurements in the soft x‐ray region is described. The x‐ray beam path of the spectrometer is enclosed in a vacuum chamber directly connected to the x‐ray generator output port. With this setup, the absorption of the x‐rays in the air is avoided. The developed spectrometer uses a monochromator equipped with cylindrically bent PET(002), KAP(001), and Ge(111) crystals of different Rowland radii working in the Johann focusing geometry. Nine stepping motors are used to control the positions of the monochromator, receiving slit, sample, and detectors. An x‐ray photon energy available in experiment ranges from about 1 keV to 5 keV. A registration of the photoelectrons emitted from the sample with the channeltron is used to carry out surface‐sensitive measurements. The performance of the developed spectrometer is illustrated by spectra measured at the absorption K‐edges of several elements from the Na‐Ti set. Copyright © 2008 John Wiley & Sons, Ltd.     

Vibrational spectroscopy and DFT calculations of di‐amino acid peptides: α‐ and β‐N‐acetyl‐L‐Asp‐L‐Glu in the solid state

Experimental vibrational spectroscopic studies and density functional theory (DFT) calculations of the di‐amino acid peptide derivatives α‐ and β‐N‐acetyl‐L‐Asp‐L‐Glu have been undertaken. Raman and infrared spectra have been recorded for samples in the solid state. DFT simulations were conducted using the B3‐LYP correlation functional and the cc‐pVDZ basis set to determine energy minimized/geometry optimized structures (based on a single isolated molecule in the gaseous state). Normal coordinate calculations have provided vibrational assignments for fundamental modes, including their potential energy distributions. Significant differences are observed between α‐ and β‐N‐acetyl‐L‐Asp‐L‐Glu both in the computed structures and in the vibrational spectra. The combination of experimental and calculated spectra provide an insight into the structural and vibrational spectroscopic properties of di‐amino acid peptide derivatives. Copyright © 2009 John Wiley & Sons, Ltd.     

A new method for functionalizing α,γ‐dinitro compounds at the β‐position: application to the cyclization of β‐alkoxy‐α,γ‐dinitro compounds

Treatment of 2,4‐dinitropentane with bromine and sodium methoxide in methanol, affords formation of an ether product, 2,4‐dibromo‐3‐methoxy‐2,4‐dinitropentane, in 59% yield as a mixture of three diastereomers. This observation has led to a general synthesis of 3‐alkoxy‐2,4‐dibromo‐2,4‐dinitropentanes, obtained in 75‐86% yield from 2,4‐dibromo‐2,4‐dinitropentane as the preferred reactant. 4‐Bromo‐2,4‐dinitro‐2‐pentene has been identified as an intermediate in these reactions. The nitroalkene has been isolated and undergoes conjugate addition with alkoxides to afford the same ether products after brominative work‐up. The nitroalkene undergoes conjugate addition with sodium azide to give 3‐azido‐2,4‐dibromo‐2,4‐dinitropentane in 38% yield as a mixture of two isomers in which the (R*,R*) isomer predominates. Sequential treatment of 2,4‐dibromo‐2,4‐dinitropentane with sodium methoxide followed by sodium iodide and acetic acid gives 3‐methoxy‐2,4‐dinitropentane in 63% yield, the overall product of simple methoxylation of 2,4‐dinitropentane. However, attempted complete debromination of 2,4‐dibromo‐3‐methoxy‐2,4‐dinitropentane with excess sodium iodide and acetic acid results only in monodebromination to give 2‐bromo‐3‐methoxy‐2,4‐dinitropentane in 86% yield. Likewise, 2‐bromo‐3‐ethoxy‐2,4‐dinitropentane is formed in 93% yield from the ethoxy analog. A mechanistic rationale is offered for condition‐specific removal of the second Br atom in these reactions. Treatment of 3‐methoxy‐2,4‐dinitropentane with potassium acetate/iodine in dimethyl sulfoxide affords formation of 4,5‐dihydro‐3,4‐dimethyl‐3‐methoxy‐4‐nitroisoxazole 2‐oxide in 30% yield as a single diastereomer. Conversion of 2‐bromo‐3‐methoxy‐2,4‐dinitropentane in 15% yield to 4,5‐dihydro‐3,4‐dimethyl‐3‐methoxy‐4‐nitroisoxazole 2‐oxide is also possible by using potassium acetate in dimethyl sulfoxide. The mechanistic pathways for formation of 4,5‐dihydro‐3,4‐dimethyl‐3‐methoxy‐4‐nitroisoxazole 2‐oxide apparently involve unstable 3‐methoxy‐1,2‐dimethyl‐1,2‐dinitrocyclopropane as the common intermediate. Similarly, 2‐bromo‐3‐ethoxy‐2,4‐dinitropentane affords 4,5‐dihydro‐3‐ethoxy‐3,4‐dimethyl‐4‐nitroisoxazole 2‐oxide in 13% yield. Copyright © 2013 John Wiley & Sons, Ltd.     

The density and tube energy dependency of cobalt Kα/Kβ in x‐ray fluorescence spectrometryfor thick target measurements

The relative intensity of K_α/K_β for cobalt in thick targets with cobalt mass densities from 0.51 to 22.49% has been measured by the wavelength dispersive x‐ray fluorescence (XRF) spectrometer. The measuring conditions are: tube current ranging from 10 to 60 mA and voltages ranging from 20 to 60 kV. We plotted the K_α/K_β ratio vs Co densities for different tube voltages and currents. Our study shows that the K_α/K_β ratio is below the theoretical value for low Co densities and it increases with increasing Co density. For higher x‐ray energies, the K_α/K_β ratio shows a sharp growth at the special density and then reaches a nearly constant value. However, K_α/K_β ratio is theoretically constant and independent of energy in thin target measurements. The changes of this ratio according to the x‐ray energy and the element density have been studied in thick target measurements. The results provide experimental evidence to suggest that exciting energy and element density can indeed affect the K_α/K_β ratio. Copyright © 2008 John Wiley & Sons, Ltd.     

Calibration of the MER α‐particle x‐ray spectrometer for detection of ‘invisible’ OH and H2O possibly present in Martian rocks and soils

An existing Monte Carlo code was modified and extended to predict the intensity ratio of elastically and inelastically scattered plutonium Lα x‐rays incident on rock samples in the Mars Exploration Rover's α‐particle x‐ray spectrometer (APXS) device. The systematics of the scatter ratio as a function of effective sample atomic number are explored. The simulated Rayleigh/Compton ratios (R/C)_sim are compared with measured ratios (R/C)_meas that are obtained by fitting APXS spectra of geochemical reference materials using an x‐ray fluorescence version of GUPIX. The quantity K = (R/C)_meas/(R/C)_sim is then plotted against the mean atomic number of the sample to provide a calibration for known samples. Departures of K values of unknown samples from this calibration may then be attributed to the presence of light, ‘invisible’ elements in the sample. This work is part of an ongoing project aimed at developing methods to quantify bound water in Martian rocks analyzed by the present and the next generation APXS instruments. Copyright © 2006 John Wiley & Sons, Ltd.     

Ramans study of Y1−xPrxBa2Cu3O7−δ and YB2Cu3−xZnxO7−δ single crystals

Single crystals with known T_c values of Y_1−xPr_xBa₂Cu₃O_7−δ (Y---Pr1:2:3) and YBa₂Cu_3−xZn_3−xZn_xO_7−δ (Y---Zn1:2:3) systems are studied by Raman measurements. The Raman spectra for (Y---Pr1:2:3) single crystals show that the frequencies of Ba and O_z modes increase as the Pr content increases. The results are consistent with the hole-localization scheme proposed for the suppression of superconductivity in the polycrystalline Y---Pr1:2:3 systems. On the other hand, in the Y---Zn1:2:3 system, all the Raman modes do not change in frequencies. However, the FWHM of the Cu(2) mode increases with the decrease of T_c, indicating strong scattering of charge carriers by the substituted Zn ions in the CuO₂ planes. The induced disorder in the CuO₂ planes may be related with suppression of T_c in the Y---Zn1:2:3 system. Thus, the suppression mechanism in the Y---Zn1:2:3 systems seems to be different from that in the Y---Pr1:2:3 systems.     

Erratum to ‘empirical approximation for Lα production cross sections’[X‐ray Spectrumetry 37, 188–192, 2008]

The original article to which this Erratum refers was published in X‐ray Spectrumetry, 37, 188–192, 2008     

In‐situ X‐ray diffraction of mechanically milled β‐Al3Mg2 powders

The structure evolution during heating of mechanically milled single‐phase β‐Al₃Mg₂ has been investigated by in‐situ X‐ray diffraction. The nanoscale supersaturated Al(Mg) solid solution formed during milling transforms back to the original β‐Al₃Mg₂ phase through a sequence of phase transformations. At low temperatures, an increasing amount of Mg is rejected from the solid solution with increasing temperature. At intermediate temperatures, the β′‐phase, a hexagonal phase with approximate composition Al₃Mg₂, forms. Finally, at higher temperatures the original β‐Al₃Mg₂ phase is restored, indicating that the formation of the supersaturated solid solution during milling can be reversed by appropriate heat treatment. The phase transformations during heating are gradual and the temperature ranges of stability of the different structure configurations are quite large, all exceeding 50 K. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Spectroscopic and structural investigations of α‐, β‐, and γ‐AlH3 phases

With its reputation as a high‐energy density fuel, aluminum hydride (AlH₃) has received renewed attention as a material that is particularly suitable, not only for hydrogen storage but also for rocket propulsion. While the various phases of AlH₃ have been investigated theoretically, there is a shortage of experimental studies corroborating the theoretical findings. In response to this, we present here an investigation of these compounds based primarily on two research areas in which there is the greatest scarcity of information in the literature, namely Raman and infrared (IR) absorption analysis. To the authors' knowledge, this is the first report of experimental far‐IR absorption results on these compounds. Two different samples prepared by broadly similar ethereal reactions of AlCl₃ with LiAlH₄ were analyzed. Both Raman and IR absorption measurements indicate that one sample is purely γ‐AlH₃ and that the other is a mixture of α‐, β‐, and γ‐AlH₃ phases. X‐ray diffraction confirms the spectroscopic findings, most notably for the β‐AlH₃ phase, for which optical spectroscopic data are reported here for the first time. Copyright © 2010 John Wiley & Sons, Ltd.     

Diffractive–refractive optics: (+,−,−,+) X‐ray crystal monochromator with harmonics separation

A new kind of two channel‐cut crystals X‐ray monochromator in dispersive (+,?,?,+) position which spatially separates harmonics is proposed. The diffracting surfaces are oriented so that the diffraction is inclined. Owing to refraction the diffracted beam is sagittally deviated. The deviation depends on wavelength and is much higher for the first harmonics than for higher harmonics. This leads to spatial harmonics separation. The idea is supported by ray‐tracing simulation.     

Wavelength dispersive x‐ray fluorescence spectrometry for the analysis of laser active lanthanides (Ln) in NaT1−xLnx(WO4)2 crystals

Four crystals with nominal compositions, NaLa_0.95Tm_0.05(WO₄)₂ (1.32 wt% of Tm), NaGd_1?xTm_x(WO₄)₂ x = 0.05, 0.07 (1.24 and 1.32 wt% of Tm, respectively) and NaY_0.9Yb_0.1(WO₄)₂ (2.81 wt% of Yb), were analyzed by wavelength dispersive x‐ray fluorescence spectrometry. A procedure for sample preparation was developed using lithium tetraborate as flux to obtain glass disks and to circumvent precipitation problems of lanthanides and tungsten experienced in their dissolution by wet routes. For this purpose three specific calibration standards with pure oxides were prepared for each analyzed element with near to constant W and Na concentrations, so that matrix effects could be properly addressed. The procedure allows measurement of the Tm and Yb concentrations above the determination limits of 0.017 wt% and 0.042 wt% for Tm in the first two crystals, respectively, and of 0.039 wt% of Yb in the last one. Further analyses show an excess with regard to the nominal formula of ≈5 mol% in the total concentration of trivalent ions incorporated to the crystal and some deficiency of Na (≈10 mol%) and W (≈2 mol%) ions. Copyright © 2009 John Wiley & Sons, Ltd.     

Phonon Raman scattering in Nd1+xBa2−xCu3O7−δ and Pr1+xBa2−xCu3O7−δ single crystals

The polarized Raman spectra of Nd_1+xBa_2−xCu₃O_7−δ (−0.023≤x≤0.107) and Pr_1+xBa_2−xCu₃O_7−δ (0.01≤x≤0.15) single crystals have been investigated. It was found that the Cu(2) A_g mode softens by 6 cm⁻¹ in Nd 1:2:3 and 4 cm⁻¹ in Pr 1:2:3 as x increases. These frequency shifts cannot be explained by the change in the relevant bond lengths due to Nd(Pr)-substitution for Ba. The variations with x of the two low frequency modes may be affected by change of their hybridization and/or change of their force constants. The linewidths of Ba mode in Pr 1:2:3 are broader than those in Y 1:2:3. This result suggests that the Pr substitution on Ba sites occurred even in a very small value of x. In x(yy) geometry the relative intensity of the Ba and O(4) modes in Nd 1:2:3 is greater than those in Pr 1:2:3. The difference between Nd 1:2:3 and Pr 1:2:3 in the relative intensity of the Ba and O(4) modes may be produced by the chains.