Arenesulfonyl bromides: The second universal class of functional initiators for the metal‐catalyzed living radical polymerization of methacrylates,acrylates, and styrenes

The metal‐catalyzed living radical polymerization of methyl methacrylate, n‐butyl acrylate, and styrene, initiated with p‐toluenesulfonyl bromide and phenoxybenzene‐4,4′‐disulfonyl bromide and catalyzed with CuBr/2,2′‐bipyridine (bpy) and various self‐regulated Cu‐based catalytic systems such as Cu₂O/bpy, Cu₂S/bpy, Cu₂Se/bpy, and Cu₂Te/bpy, is reported. Similarities and differences between the arenesulfonyl chloride and arenesulfonyl bromide initiators are discussed. The arenesulfonyl bromide initiators require reduced reaction times to produce polymers in high conversions under milder reaction conditions than the corresponding arenesulfonyl chloride initiators. At the same time, they exhibit 100% initiator efficiency and generate polymers with narrow molecular weight distributions and functional chain ends. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 319–330, 2005     

Cu powder‐catalyzed single electron transfer‐living radical polymerization of acrylonitrile

Single electron transfer‐living radical polymerization (SET‐LRP) has been used as a new technique for the synthesis of polyacrylonitrile (PAN) catalyzed by Cu(0) powder with carbon tetrachloride (CCl₄) as the initiator and hexamethylenetetramine (HMTA) as the ligand in N,N‐dimethylformamide (DMF) or mixed solvent. Well‐controlled polymerization has been achieved as evidenced by a linear increase of molecular weight with respect to monomer conversion as well as narrow molecular weight distribution. Kinetics data of the polymerizations at both ambient temperature and elevated temperature demonstrate living/controlled feature. An increase in the concentration of ligand yields a higher monomer conversion within the same time frame and almost no polymerization occurs in the absence of ligand due to the poor disproportionation reaction of Cu(I). The reaction rate exhibits an increase with the increase of the amount of catalyst Cu(0)/HMTA. Better control on the molecular weight distribution has been produced with the addition of CuCl₂. In the presence of more polar solvent water, it is observed that there is a rapid increase in the polymerization rate. The effect of initiator on the polymerization is also preliminarily investigated. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Single electron transfer‐living radical polymerization of methyl methacrylate catalyzed by ytterbium powder

Zerovalent ytterbium (Yb) powder is firstly used as a catalyst in single electron transfer‐living radical polymerization of methyl methacrylate initiated by carbon tetrachloride in N, N‐dimethylformamide (DMF) and dimethyl sulfoxide, respectively. Polymerization proceeds in a “living”/controlled way as evidenced by kinetic studies and chain extension results, producing well‐defined polymers with controlled degree of polymerization and narrow molecular weight distribution. The apparent activation energy of polymerization in DMF is accounted to be 36.2 kJ/mol, and the energy of equilibrium state is calculated to be 13.9 kJ/mol. An increase in the concentration of Yb(0) yields a higher monomer conversion. It is observed that polymerization rate experiments a rapid increase in the presence of more polar solvent water, and increasing in the content of H₂O results in an increase in the apparent rate constant of polymerization, and a decrease in the molecular weight distribution. The reaction rate and molecular weight increase along with the decrease of DMF content. The effect of Yb(0) powder content, different ligands and concentration of initiator on the polymerization is also investigated. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Outer‐sphere electron transfer metal‐catalyzed polymerization of styrene using a macrobicyclic ligand

The CuBr‐catalyzed polymerizations of styrene in the presence of a macrobicyclic mixed donor (N and S) encapsulating ligand, NH₂capten, were carried out in toluene at 60 and 100 °C. The macrobicyclic nature of the ligand ensures that a transition metal ion is effectively encapsulated (caged) within the three‐dimensional cavity, resulting in activation of radicals through an outer‐sphere electron transfer mechanism. The kinetic data showed that the polymerizations were uncontrolled with little “living” behavior. The external orders of reaction in [CuBr], [NH₂capten], and [CuBr₂] were 0.5, 0.5, and close to zero, respectively, in agreement with the postulated mechanism of little or no deactivation of polymeric radicals and a significant amount of bimolecular termination. Although “living” behavior was not found using the cage ligand, it was decided that it would provide an ideal method for radical coupling experiments to make high‐molecular weight multiblock copolymers from a difunctional PSTY (Br‐PSTY‐Br, PDI = 1.11). The coupling reaction of Br‐PSTY‐Br using CuBr/NH₂capten and excess Cu(0) in toluene at 100 °C gave no loss of the starting Br‐PSTY‐Br. Changing the solvent to the aprotic DMSO resulted in a significant increase in the rate of consumption of starting Br‐PSTY‐Br, with over 87% being used in under 10 min at 60 °C. In addition, higher molecular weight species were also formed, suggesting that OSET gives little or no side reactions on this time scale. It was initially thought that to get such high rates of reaction that the SET‐LRP disproportionation mechanism (2Cu(I) → Cu(0) + Cu(II)) was at play. However, UV–Vis experiments of the CuBr/NH₂capten showed little or no disproportionation products. This important result suggests that DMSO catalyzes the OSET reaction through the stabilization of the radical‐anion intermediate, which then rapidly fragments to a polymeric radical. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 146–154, 2008     

N‐chloro amides,lactams, carbamates,and imides. New classes of initiators for the metal‐catalyzed living radical polymerization of methacrylates

Metal‐catalyzed living radical polymerization of methyl methacrylate initiated with N‐chloro amides (N‐chloro N‐ethyl propionamide, N‐chloro benzanilide, N‐chloro methylbenzamide, and N‐chloro acetanilide), lactams (N‐chloro caprolactam and N‐chloro 2‐pyrrolidinone), carbamates or urethanes (N‐chloro ethylcarbamate or N‐chlorourethane), imides (N‐chloro phtalimide, N‐chloro succinimide, trichloroisocyanuric acid, and N‐chloro saccharin) and catalyzed with the self‐regulated catalytic system Cu₂S/2,2′‐bipyridine is reported. The initiation efficiency of these initiators is determined by their structure. Regardless of the initiator efficiency, in all cases, poly (methyl methacrylate) with narrow molecular weight distribution and functionalized chain‐ends was obtained. These new classes of initiators open new strategies for the functionalization of polymer chain‐ends and for the synthesis of complex architectures by graft copolymerization initiated from N‐chloro proteins, aliphatic, aromatic and semiaromatic polyamides, and polyurethanes. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5283–5299, 2005     

Kinetic analysis of styrene atom transfer radical polymerization: Extraction of radical‐radical termination rate coefficients

Kinetic studies of the atom transfer radical polymerization (ATRP) of styrene are reported, with the particular aim of determining radical‐radical termination rate coefficients (<k_t>). The reactions are analyzed using the persistent radical effect (PRE) model. Using this model, average radical‐radical termination rate coefficients are evaluated. Under appropriate ATRP catalyst concentrations, <k_t> values of approximately 2 × 10⁸ L mol^?1 s^?1 at 110 °C in 50 vol % anisole were determined. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5548–5558, 2004     

Mechanism and kinetics of the imidazolidinone nitroxide‐mediated free‐radical polymerization of styrene

Styrene radical polymerizations mediated by the imidazolidinone nitroxides 2,5‐bis(spirocyclohexyl)‐3‐methylimidazolidin‐4‐one‐1‐oxyl (NO88Me) and 2,5‐bis(spirocyclohexyl)‐3‐benzylimidazolidin‐4‐one‐1‐oxyl (NO88Bn) were investigated. Polymeric alkoxyamine (PS‐NO88Bn)‐initiated systems exhibited controlled/living characteristics at 100–120 °C but not at 80 °C. All systems exhibited rates of polymerization similar to those of thermal polymerization, with the exception of the PS‐NO88Bn system at 80 °C, which polymerized twice as quickly. The dissociation rate constants (k_d) for the PS‐NO88Me and PS‐NO88Bn coupling products were determined by electron spin resonance at 50–100 °C. The equilibrium constants were estimated to be 9.01 × 10^?11 and 6.47 × 10^?11 mol L^?1 at 120 °C for NO88Me and NO88Bn, respectively, resulting in the combination rate constants (k_c) 2.77 × 10⁶ (NO88Me) and 2.07 × 10⁶ L mol^?1 s^?1 (NO88Bn). The similar polymerization results and kinetic parameters for NO88Me and NO88Bn indicated the absence of any 3‐N‐transannular effect by the benzyl substituent relative to the methyl substituent. The values of k_d and k_c were 4–8 and 25–33 times lower, respectively, than the reported values for PS‐TEMPO at 120 °C, indicating that the 2,5‐spirodicyclohexyl rings have a more profound effect on the combination reaction rather than the dissociation reaction. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 327–334, 2003     

AGET ATRP of water‐soluble PEGMA: Fast living radical polymerization mediated by iron catalyst

In this work, living radical polymerizations of a water‐soluble monomer poly(ethylene glycol) monomethyl ether methacylate (PEGMA) in bulk with low‐toxic iron catalyst system, including iron chloride hexahydrate and triphenylphosphine, were carried out successfully. Effect of reaction temperature and catalyst concentration on the polymerization of PEGMA was investigated. The polymerization kinetics showed the features of “living”/controlled radical polymerization. For example, M_n,GPC values of the resultant polymers increased linearly with monomer conversion. A faster polymerization of PEGMA could be obtained in the presence of a reducing agent Fe(0) wire or ascorbic acid. In the case of Fe(0) wire as the reducing agent, a monomer conversion of 80% was obtained in 80 min of reaction time at 90 °C, yielding a water‐soluble poly(PEGMA) with M_n = 65,500 g mol^?1 and M_w/M_n = 1.39. The features of “living”/controlled radical polymerization of PEGMA were verified by analysis of chain‐end and chain‐extension experiments. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Influence of nitroxide structure on the 2,5‐ and 2,6‐spirodicyclohexyl substituted cyclic nitroxide‐mediated free‐radical polymerization of styrene

The 2,6‐spirodicyclohexyl substituted nitroxide, cyclohexane‐1‐spiro‐2′‐(3′,5′‐dioxo‐4′‐benzylpiperazine‐1′‐oxyl)‐6′‐spiro‐1″‐cyclohexane (BODAZ), was investigated as a mediator for controlled/living free‐radical polymerization of styrene. The values of the number‐average molecular weight increased linearly with conversion, but the polydispersities were higher than for the corresponding 2,2,6,6‐tetramethylpiperidinyl‐1‐oxy (TEMPO) and 2,5‐bis(spirocyclohexyl)‐3‐benzylimidazolidin‐4‐one‐1‐oxyl (NO88Bn) mediated systems at approximately 2.2 and 1.6 at 100 and 120 °C, respectively. These results were reflected in the rate coefficients obtained by electron spin resonance spectroscopy; at 120 °C, the values of the rate coefficients for polystyrene‐BODAZ alkoxyamine dissociation (k_d), combination of BODAZ and propagating radicals (k_c), and the equilibrium constant (K) were 1.60 × 10^?5 s^?1, 5.19 × 10⁶ M^?1 s^?1, and 3.08 × 10^?12 M, respectively. The value of k_d was approximately one and two orders of magnitude lower, and that of K was approximately 20 and 7 times lower than for the NO88Bn and TEMPO adducts. These results are explained in terms of X‐ray crystal structures of BODAZ and NO88Bn; the six‐membered ring of BODAZ deviates significantly from planarity as compared to the planar five‐membered ring of NO88Bn and possesses a benzyl substituent oriented away from the nitroxyl group leading to a seemingly more exposed oxyl group, which resulted in a higher k_c and a lower k_d than NO88Bn. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3892–3900, 2003     

Preparation of polyacrylonitrile via SET‐LRP catalyzed by lanthanum powder in the presence of VC

A novel catalyst system based on La(0)/hexamethylenetetramine (HMTA) complexes is used for single electron transfer‐living radical polymerization (SET‐LRP) of acrylonitrile (AN) in the presence of ascorbic acid (VC) with carbon tetrachloride (CCl₄) as a initiator and N,N‐dimethylformamide (DMF) as a solvent. Compared with SET‐LRP of AN in the absence of VC, monomer conversion is markedly increased. SET‐LRP of AN in the presence of VC is also conducted in the presence of air. The kinetic studies show that the polymerizations both in the absence of oxygen and in the presence of air proceed in a well‐controlled manner. With the respect to the polymerization in the absence of oxygen, the polymerization in the presence of air provides slower reaction rate and broader polydispersity. Effects of amount of VC, La, CCl₄, and are investigated in detail. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4088–4094     

From metal‐catalyzed radical telomerization to metal‐catalyzed radical polymerization of vinyl chloride: Toward living radical polymerization of vinyl chloride

The metal‐catalyzed radical polymerization of vinyl chloride (VC) in ortho‐dichlorobenzene initiated with various activated halides, such as α,α‐dihaloalkanes, α,α,α‐trihaloalkanes, perfloroalkyl halides, benzyl halides, pseudohalides, allyl halides, sulfonyl halides, α‐haloesters, α‐halonitriles, and imidyl halides, in the presence of Cu(0)/2,2′‐bipyridine, Fe(0)/o‐phenantroline, TiCp₂Cl₂, and other metal catalysts is reported. The formation of the monoadduct between the initiator and VC was achieved with all catalysts. However, propagation was observed only for metals in their zero oxidation state because they were able to reinitiate from geminal dihalo or allylic chloride structures. Poly(vinyl chloride) with molecular weights larger then the theoretical limit allowed by chain transfer to VC were obtained even at 130 °C. In addition, the most elemental features of a living radical polymerization, such as a linear dependence of the molecular weight and a decrease of polydispersity with conversion, were observed for the most promising systems based on iodine‐containing initiators and Cu(0), that is, I? CH₂? Ph? CH₂? I/Cu(0)/bpy (where bpy = 2,2′‐bipyridyl), at 130 °C. However, because of the formation of inactive species via chain transfer to VC and other side reactions, the observed conversions were in most cases lower than 40%. A mechanistic interpretation of the chain transfer to monomer in the presence of Cu species is proposed. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3392–3418, 2001     

Synthesis of poly(N‐isopropylacrylamide) with a low molecular weight and a low polydispersity index by single‐electron transfer living radical polymerization

The single‐electron transfer living radical polymerization (SET‐LRP) method in the presence of chain transfer agent was used to synthesize poly(N‐isopropylacrylamide) [poly(NIPAM)] with a low molecular weight and a low polydispersity index. This was achieved using Cu(I)/2,2′‐bipyridine as the catalyst, 2‐bromopropionyl bromide as the initiator, 2‐mercaptoethanol as the chain transfer agent (TH), and N,N‐dimethylformamide (DMF) as the solvent at 90 °C. The copper nanoparticles with diameters of 16 ± 3 nm were obtained in situ by the disproportionation of Cu(I) to Cu(0) and Cu(II) species in DMF at 22 °C for 24 h. The molecular weights of poly(NIPAM) produced were significantly higher than the theoretical values, and the polydispersities were less than 1.18. The chain transfer constant (C_tr) was found to be 0.051. Although the kinetic analysis of SET‐LRP in the presence of TH corroborated the characteristics of controlled/living polymerization with pseudo‐first‐order kinetic behavior, the polymerization also exhibited a retardation period (k > k_tr). The influence of molecular weight on lower critical solution temperature (LCST) was investigated by refractometry. Our experimental results explicitly elucidate that the LCST values increase slightly with decreasing molecular weight. Reversibility of solubility and collapse in response to temperature well correlated with increased molecular weight of poly(NIPAM). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Poly(methyl methacrylate‐co‐pentaerythritol tetraacrylate‐co‐butyl methacrylate)‐g‐polystyrene: Synthesis and high oil‐absorption property

Well‐defined high oil‐absorption resin was successfully prepared via living radical polymerization on surface of polystyrene resin‐supported N‐chlorosulfonamide group utilizing methyl methacrylate and butyl methacrylate as monomers, ferric trichloride/iminodiacetic acid (FeCl₃/IDA) as catalyst system, pentaerythritol tetraacrylate as crosslinker, and L ‐ascorbic acid as reducing agent. The polymerization proceeded in a “living” polymerization manner as indicated by linearity kinetic plot of the polymerization. Effects of crosslinker, catalyst, macroinitiator, reducing agent on polymerization and absorption property were discussed in detail. The chemical structure of sorbent was determined by FTIR spectrometry. The oil‐absorption resin shows a toluene absorption capacity of 21 g g^?1. The adsorption of oil behaves as pseudo‐first‐order kinetic model rather than pseudo‐second‐order kinetic model. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Quenching of metal‐catalyzed living radical polymerization with silyl enol ethers

Various silyl enol ethers were employed as quenchers for the living radical polymerization of methyl methacrylate with the R Cl/RuCl₂(PPh₃)₃/Al(Oi–Pr)₃ initiating system. The most effective quencher was a silyl enol ether with an electron‐donating phenyl group conjugated with its double bond [CH₂C(OSiMe₃)(4‐MeOPh) ( 2a )] that afforded a halogen‐free polymer with a ketone terminal at a high end functionality [F̄_n ∼ 1]. Such silyl compounds reacted with the growing radical generated from the dormant chloride terminal and the ruthenium complex to give the ketone terminal via the release of the silyl group along with the chlorine that originated from the dormant terminal. In contrast, less conjugated silyl enol ethers such as CH₂C(OSiMe₃)Me were less effective in quenching the polymerization. The reactivity of the silyl compounds to the poly(methyl methacrylate) radical can be explained by the reactivity of their double bonds, namely, the monomer reactivity ratios of their model vinyl monomers without the silyloxyl groups. The lifetime of the living polymer terminal was also estimated by the quenching reaction mediated with 2a . © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4735–4748, 2000     

Chain transfer to solvent in the radical polymerization of N‐isopropylacrylamide

Chain transfer to solvent has been investigated in the conventional radical polymerization and nitroxide‐mediated radical polymerization (NMP) of N‐isopropylacrylamide (NIPAM) in N,N‐dimethylformamide (DMF) at 120 °C. The extent of chain transfer to DMF can significantly impact the maximum attainable molecular weight in both systems. Based on a theoretical treatment, it has been shown that the same value of chain transfer to solvent constant, C_tr,S, in DMF at 120 °C (within experimental error) can account for experimental molecular weight data for both conventional radical polymerization and NMP under conditions where chain transfer to solvent is a significant end‐forming event. In NMP (and other controlled/living radical polymerization systems), chain transfer to solvent is manifested as the number‐average molecular weight (M_n) going through a maximum value with increasing monomer conversion. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Single‐electron transfer‐living radical copolymerization of butyl methacrylate and divinylbenzene for preparation of oil‐absorbing gel

Crosslinking copolymerization of butyl methacrylate with a small amount of divinylbenzene (DVB) was carried out using single‐electron transfer‐living radical polymerization initiated with carbon tetrachloride (CCl₄) and catalyzed by Cu(0)/N‐ligand in N,N‐dimethylformamide to produce a highly oil‐absorbing gel. The polymerization, gelation process, and oil‐absorbing properties were studied in detail. Analysis of monomer conversion with reaction time showed that the polymerization followed first‐order kinetics for both linear and crosslinking polymerization before gelation. Higher levels of DVB led to earlier gelation and the influence of N‐ligand on gelation was also significant. Under optimal conditions, oil absorption of the prepared gel to chloroform could reach 42.1 g·g^?1. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3233–3239     

Nitroxide‐mediated radical polymerization in miniemulsion: Bimolecular termination in monomer‐free model systems

Bimolecular termination in nitroxide‐mediated radical polymerization in miniemulsion has been investigated through the heating of a polystyrene–2,2,6,6‐tetramethylpiperidinyl‐1‐oxy macroinitiator and its 4‐hydroxy‐2,2,6,6‐tetramethylpiperidinyl‐1‐oxy analogue in an aqueous toluene dispersion with sodium dodecyl benzenesulfonate as a surfactant at 125 °C. The level of bimolecular termination by combination, evaluated from the high‐molecular‐weight shoulder, was higher in miniemulsion than in solution and increased with decreasing particle size. Quantitative analysis revealed that these results cannot be rationalized solely by nitroxide partitioning to the aqueous phase. The results are explained by an interface effect, by which nitroxide is adsorbed or located at the aqueous–organic interface. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4995–5004, 2007     

Synthesis of poly(2‐methoxyethyl acrylate) by single electron transfer—Degenerative transfer living radical polymerization catalyzed by Na2S2O4 in water

Living radical polymerization of 2‐methoxyethyl acrylate (MEA) was achieved by single‐electron‐transfer/degenerative transfer mediated living radical polymerization (SET‐DTLRP) in water catalyzed by sodium dithionate. The poly(2‐methoxyethyl acrylate) is an amphiphilic polymer with a hydrophobic part (polyethylene chain) and a mildly hydrophilic tail. The plots of number‐average molecular weight versus conversion and ln{[M]₀/[M]} versus time are linear, indicating a controlled polymerization. This method leads to the preparation of α,ω‐di(iodo) poly(2‐methoxyethyl acrylate)s (α,ω‐di(iodo)PMEA) macroinitiators that can be further functionalized. The molecular weight distributions were determined using a combination of three detectors (TriSEC): right‐angle light scattering (RALLS), a differential viscometer (DV) and refractive index (RI). The method studied in this work represents a possible route to prepare well‐tailored macromolecules made of 2‐methoxyethyl acrylate (biocompatible material) in an environmentally friendly reaction medium. To the best of our knowledge there is no previous report dealing with the synthesis of PMEA by any LRP approach in aqueous medium. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4454–4463, 2009