Monitoring phase transition of aqueous biomass model substrates by high‐pressure and high‐temperature microfluidics

Aqueous‐Phase Reforming (APR) is a promising hydrogen production method, where biomass is catalytically reformed under high pressure and high temperature reaction conditions. To eventually study APR, in this paper, we report a high‐pressure and high‐temperature microfluidic platform that can withstand temperatures up to 200°C and pressures up to 30 bar. As a first step, we studied the phase transition of four typical APR biomass model solutions, consisting of 10 wt% of ethylene glycol, glycerol, xylose or xylitol in MilliQ water. After calibration of the set‐up using pure MilliQ water, a small increase in boiling point was observed for the ethylene glycol, xylitol and xylose solutions compared to pure water. Phase transition occurred through either explosive or nucleate boiling mechanisms, which was monitored in real‐time in our microfluidic device. In case of nucleate boiling, the nucleation site could be controlled by exploiting the pressure drop along the microfluidic channel. Depending on the void fraction, various multiphase flow patterns were observed simultaneously. Altogether, this study will not only help to distinguish between bubbles resulting from a phase transition and/or APR product formation, but is also important from a heat and mass transport perspective.     

Morphology investigation on high‐pressure crystallized bisphenol‐A polycarbonate/dioctyl phthalate blends

The high‐pressure crystallized bisphenol‐A polycarbonate/dioctyl phthalate (BAPC/DOP) blend samples were investigated using wide‐angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). The specimens were prepared in a piston‐cylinder high‐pressure apparatus by varying the temperature, the pressure and the crystallization time for a BAPC/DOP (90/10, wt/wt) blend. The other four specimens were also prepared with different weight ratios of BAPC/DOP. The DSC results showed that the amorphous BAPC could be crystallized in 45 min by the blending with DOP and the subsequent high‐pressure treatment. A wide variety of morphologies of BAPC crystals were disclosed by SEM, including spherulites, spatial dendrites, crystalbars, platelets and regular polygonal crystals of different characteristics. The folded‐chain lamellar crystals were found to be the substructures of these observed BAPC microstructures. The SEM revealed a granular substructure of the lamellae in a low‐crystallinity sample as well, which indicated that the crystallization of BAPC in the multiphase system might possibly agree with the model developed by Strobl. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2715–2728, 2007     

Order‐order transitions of a triblock copolymer with a homopolymer (ABC/A) blend film induced by saturated solvent vapor annealing

The morphology transition of binary mixtures of polystyrene‐block‐poly(butadiene)‐block‐poly(2‐vinylpyridine)(SBV) triblock and polystyrene (PS) homopolymer thin films was investigated as a function of the volume fraction of added homopolymer and the annealing time in benzene vapor. It was found that the weight ratio of PS in the blends influenced the transition process. When PS content was >5%, the order‐order transition (OOT) of core‐shell cylinders (C) →sphere in “diblock Gyroid” (sdG) → sphere in lamella (sL) → sphere (S) was observed, which was similar to ABC triblock copolymer except for the increased surface area of the PS phase. When PS content reached to 10–30%, the OOT in the sequence of C → sL → S was observed. The disappearance of the Gyroid phase is due to the change of the effective volume fraction. Further increasing the PS content, C phase also disappeared and sL → S was expected to take place. © 2014 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2014 , 52, 1030–1036     

Three‐Dimensional Structure of Olefinic Thermoplastic Elastomer Blends Using Electron Tomography

Summary: The present communication reports the first use of electron tomography in reconstructing the three‐dimensional morphology in thermoplastic elastomer blends. The blends investigated were dynamically vulcanized blends of ethylene‐propylene‐diene (EPDM) rubber/poly(propylene)/oil and polystyrene‐block‐(ethylene‐co‐butylene)‐block‐polystyrene (SEBS)/poly(propylene)/oil. An easy identification of blend morphology could be carried out at blend compositions, where conventional transmission electron microscopic imaging gives misleading information. This technique gives a higher resolution than any other microscopic technique, and is applicable to blends with dispersed as well as co‐continuous morphologies.

Example of a tomographic model of partially co‐continuous SEBS phases in a SEBS/PP/oil thermoplastic blend. Only the contours of the SEBS phase are shown.     

Melt‐flow‐induced phase morphologies of a high‐density polyethylene/poly(ethylene‐co‐1‐octene) blend

A blend of high‐density polyethylene and an elastomeric poly(ethylene‐co‐1‐octene) resin, containing 25 mol % octene and long‐chain branching, was phase‐separated in the melt under quiescent conditions. After melt flow, the blend had fine globular or interconnected phase morphologies that were interpreted as originating from the various stages of coarsening after liquid–liquid phase separation through spinodal decomposition. It was inferred that the miscibility of the blend was enhanced under melt flow. After cessation of flow, concurrent liquid–liquid and solid–liquid phase separation took place, resulting in the formation of an interpenetrating morphology comprising amorphous polyethylene, copolymer, and crystalline polyethylene. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 380–389, 2001     

Ultra‐high‐pressure‐assisted extraction of wedelolactone and isodemethylwedelolactone from Ecliptae Herba and purification by high‐speed counter‐current chromatography

Ultra‐high‐pressure extraction combined with high‐speed counter‐current chromatography was employed to extract and purify wedelolactone and isodemethylwedelolactone from Ecliptae Herba. The operating conditions of ultra‐high‐pressure extraction were optimized using an orthogonal experimental design. The optimal conditions were 80% aqueous methanol solvent, 200 MPa pressure, 3 min extraction time and 1:20 (g/mL) solid–liquid ratio for extraction of wedelolactone and isodemethylwedelolactone. After extraction by ultra‐high pressure, the extraction solution was concentrated and subsequently extracted with ethyl acetate; a total of 2.1 g of crude sample was obtained from 100 g of Ecliptae Herba. A two‐phase solvent system composed of petroleum ether–ethyl acetate–methanol–water (3:7:5:5, v/v) was used for high‐speed counter‐current chromatography separation, by which 23.5 mg wedelolactone, 6.8 mg isodemethylwedelolactone and 5.5 mg luteolin with purities >95% were purified from 300 mg crude sample in a one‐step separation. This research demonstrated that ultra‐high‐pressure extraction combined with high‐speed counter‐current chromatography was an efficient technique for the extraction and purification of coumestans from plant material.     

Fiber‐forming blend polypropylene‐polyvinyl alcohol

The preparation of a fiber‐forming blend consisting of polypropylene and polyvinyl alcohol mixed with glycerol and with polypropylene grafted with maleic anhydride were studied. The physical and mechanical properties of blend fibers were also studied. The rheological measurements for semiquantitative evaluation of technological compatibility of the components and for processing the polymeric material in extruding and spinning process were carried out. The experimental results revealed the technological compatibility of the polypropylene‐polyvinyl alcohol blend in the presence of glycerol and polypropylene grafted with maleic anhydride. The colloidal structure of interface layer is assumed to be in a three‐ or four‐component system. The mixture of polyvinyl alcohol with glycerol allows for the preparation of well spun fiber‐forming polypropylene blends. Polypropylene‐polyvinyl alcohol blend fibers consisting of up to 20% polyvinyl alcohol with sufficient mechanical properties, higher porosity and significantly higher sorption of water than polypropylene fibers alone were prepared. Copyright © 2001 John Wiley & Sons, Ltd.     

Thermoplastic elastomer based on high‐density polyethylene/natural rubber blends: rheological,thermal, and morphological properties

Thermoplastic elastomer (TPE) comprising air‐dried sheet or natural rubber (ADS or NR) and high‐density polyethylene (HDPE) was prepared by a simple blending technique. NR and HDPE were mixed with each type of phenolic compatibilizer (HRJ‐10518 or SP‐1045) or liquid natural rubber (LNR) at 180°C in an internal mixer. The mixing torque, shear stress, and shear viscosity of the blends increased with increasing amounts of NR. Positive deviation blend (PDB) for the blends containing active hydroxyl methyl phenolic resin in HRJ‐10518 or dimethyl phenolic resin in SP‐1045 was obtained. PDB was not observed for the blends without the compatibilizers or with LNR. The blends with HRJ‐10518 or SP‐1045 were compatible or partially compatible while the LNR blends were incompatible. In the phenolic compatibilized blends, NR dispersed in the HDPE matrix was found in the NR/HDPE blends of 20/80, 40/60, and 50/50 ratios. HDPE dispersed in NR matrix was obtained in the NR/HDPE blend of 80/20 ratio, and the co‐continuous phase was accomplished in the NR/HDPE blend of 60/40 ratio. The NR/HDPE blend at 60/40 ratio compatibilized with HRJ‐10518 and fabricated by a simple plastic injection molding machine exhibited higher ultimate tensile strength and elongation at break (EB). Incorporation of parafinic oil caused a decreasing tendency in tensile strength with increases in EB. The TPNRs exhibited high elastomeric nature with low‐tension set. Copyright © 2007 John Wiley & Sons, Ltd.     

Quantification issues in ToF‐SSIMS and AFM co‐analysis in two‐phase systems,exampled by a polymer blend

This study concerns the measurement of the surface properties of sensitive materials, exampled by a polymer blend of polyvinyl chloride (PVC) and polycarbonate (PC), by static secondary ion mass spectrometry (SSIMS) and atomic force microscopy (AFM) operated in force modulation microscopy mode. It is shown that SSIMS, although damaging the surface little, causes significant subsurface damage. This changes the material behaviour in the irradiated region and leads to changes in the AFM measurements of both the topography and nanomechanical parameters such as the elastic moduli. Alternatively, if AFM is conducted first, contact with the tip may lead to modification of the surface. In order to minimize damage, soft cantilevers (spring constant ～0.1 N m^?1) are used. It is recommended that analyses be conducted on identifiably equivalent or partially overlapping regions, where any damage effects may be separated. Because, in SSIMS, a flood gun neutralizer must be used that irradiates the whole sample, it is recommended that AFM analysis is conducted prior to SSIMS even if different areas of the same sample are to be studied. The fractional areas identified by atomic species in SSIMS and separately by AFM are both the same and give the consistent ratio PVC/PC = 44 : 56. Both of these analyses are characteristic of the substrate below the top monolayer. The fractional areas determined using molecular species in SSIMS and by G‐SIMS both give PVC/PC = 20 : 80, which is interpreted to show that more than half of the PVC surface is covered by a monolayer of PC. Copyright © 2003 John Wiley & Sons, Ltd.     

Effects of the location of the nanoclay at the interface on the mechanical properties of a maleic anhydride grafted polypropylene/polyamide 6/organoclay co‐continuous blend

The effects of the location at the interface of an organoclay on the morphology and mechanical properties of a maleated‐polypropylene/polyamide 6 based co‐continuous blend have been studied. The organoclay is located at the interface because the level of interaction with each of the two polymers was similar. The dispersed particle size remained unchanged with organoclay content because the effect of viscosity and coalescence inhibition was offset by the surfactant compatibilization hindering. The Young's modulus remained constant; this behavior is mainly attributed to the inefficient orientation of the nanoclay. The ductility behavior suggests that there is a maximum amount of organoclay that can be located at the interface while retaining its ductile nature. Once this amount has been exceeded, the interface becomes saturated, and the dispersed particles become encapsulated. Encapsulation means that both an inorganic barrier and discontinuity appear, hindering the stress transmission through the interface and leading to fragility. Copyright © 2012 John Wiley & Sons, Ltd.     

Modulated‐temperature differential scanning calorimetry study of temperature‐induced mixing and demixing in poly(vinylmethylether)/water

The heat capacity or reversing heat flow signal from modulated‐temperature differential scanning calorimetry can be used to measure the onset of phase separation in a poly(vinylmethylether)/water mixture, clearly showing the special type III lower critical solution temperature demixing behavior. Characteristic of this demixing behavior is a three‐phase region, which is detected in the nonreversing heat flow signal. Stepwise quasi‐isothermal measurements through the phase transition show large excess contributions in the (apparent) heat capacity signal, caused by demixing/remixing heat effects on the timescale of the modulation (fast process). These excess contributions and their time‐dependent evolutions (slow process) are useful in understanding the kinetics of phase separation and the morphology (interphase) development. Care has to be taken, however, in interpreting the heat capacity signal derived from the amplitude of the modulated heat flow because nonlinear effects lead to the occurrence of higher harmonics. Therefore, the raw heat flow signal for quasi‐isothermal demixing and remixing measurements is also examined in the time domain. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1824–1836, 2003     

Enzymatic Degradation of Semi‐IPN Hydrogels Based on N‐Isopropylacrylamide and Dextran at a Specific Temperature Range

The temperature‐dependent enzymatic degradation of semi‐IPN hydrogels consisting of dextran grafted with thermo‐responsive chains (lower cloud point) and a thermo‐responsive crosslinked matrix (higher cloud point) was examined. Enzymatic degradation of the semi‐IPN hydrogel was significantly inhibited below the lower and above the higher cloud point. Only between both cloud points, enzymatic degradation proceeded. The designed semi‐IPN hydrogel is therefore advantageous to achieve enzymatic degradation at a specific temperature range.     

Extended‐chain crystals in high‐pressure crystallized poly(ethylene terephthalate)/bisphenol a polycarbonate blends

Morphologies of extended‐chain crystals with different characteristics were observed with scanning electron microscopy (SEM) in the high‐pressure crystallized polyethylene terephthalate/polycarbonate (PET/PC) blends. The crystals memorize their nucleation and growth process, which reveal an involvement of different mechanisms simultaneously. The presence of sliding diffusion during crystal thickening is indicated by a wedge shape of some crystals, while bent crystals suggest the occurrence of transesterification in the formation of the large extended‐chain crystals. The observation of two morphological features on one group of crystals shows that two mechanisms may work simultaneously. The connection between folded‐chain and extended‐chain crystals is demonstrated by the S‐shaped extended‐chain crystals as well as their direct morphological connection observed with SEM. Though transesterification plays the essential role in the formation of the large crystals, which acts in different aspects during the process, the thermodynamic driving force is the enthalpy gain associated with large crystals. This is a high‐pressure self‐assembly with a coupling between crystallization and transesterification, which may be instructive to grow such large crystals in similar polymer systems. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3148–3156, 2006     

Acyclic N‐halamine‐based fibrous materials: Preparation,characterization, and biocidal functions

Methacrylamide (MAA) was grafted onto cotton cellulose. The influence of the reaction conditions on the grafting was studied in detail. Upon a chlorine bleach treatment, some of the amide groups in the grafted MAA side chains were transformed into stable acyclic N‐halamines; Hoffman‐type degradation was not observed. The resultant cotton celluloses provided a total kill of 10⁸–10⁹ CFU/mL for Escherichia coli (Gram‐negative bacteria), Staphylococcus aureus (Gram‐positive bacteria), and Candida tropicalis (fungi) in 3 min, 10⁶–10⁷ PFU/mL for the MS2 virus in 5 min, and 10⁶–10⁷ spores/mL for Bacillus subtilis in 4 h. The antibacterial, antifungal, antiviral, and antispore activities were both durable and rechargeable. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3588–3600, 2006     

Preparation of polypyrrole‐graft‐poly(N‐isopropylacrylamide)/silver nanocomposites from pyrrolyl‐capped macromonomer by AgNO3 and their stimuli responsibility of light emission

Pyrrolyl‐capped poly(N‐isopropylacrylamide) macromonomers (Py‐PNIPAM) were prepared through reversible addition‐fragmentation‐transfer polymerization with benzyl 1‐pyrrolylcarbodithioate as chain‐transfer agent. Polymerizations of Py‐PNIPAM with/without pyrrole using AgNO₃ as oxidizing agent and dimethylforamide as solvent resulted in graft copolymers of polypyrrole‐graft‐poly(N‐isopropylacrylamide) (PPy‐g‐PNIPAM) as well as silver nanoparticles, leading to the formation of PPy‐g‐PNIPAM/silver nanocomposites. The resulting nanocomposites were soluble in water when the content of PPy was low, and when the molar ratio of Py/Py‐PNIPAM increased to 30, the resulting products became insoluble in water. The resulting nanocomposites had special optical properties because of PPy as well as the temperature‐responsible PNIPAM. The chemical structure and composition of nanocomposite were characterized by ¹H nuclear magnetic resonance spectroscopy, gel permeation chromatograms, fourier transform infrared spectroscopy, and X‐ray diffraction. Their optical properties were characterized by UV–vis and fluorescence spectroscopy. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6950–6960, 2008     

Separation of ethylene‐propylene copolymers and ethylene‐propylene‐diene terpolymers using high‐temperature interactive liquid chromatography

Ethylene‐propylene‐diene terpolymers (EPDM) are generally amorphous and, therefore, do not crystallize from solution. Consequently, fractionation techniques based on crystallization, such as crystallization analysis fractionation or temperature rising elution fractionation, cannot be used to analyze their chemical composition distribution. Moreover, no suitable chromatographic system was known, which would enable to separate them according to their chemical composition. In this study, two different sorbent/solvent systems are tested with regard to the capability to separate EPDM‐terpolymers and ethylene‐propylene (EP)‐copolymers according to chemical composition. While porous graphite/1‐decanol system is selective towards ethylene and ethylidene‐2‐norbornene, carbon coated zirconia/2‐ethyl‐1‐hexanol is preferentially selective towards ethylene. Consequently, the earlier system enables to separate both EP copolymers and EPDM according to the chemical composition and the latter mainly according to the ethylene content. The results prove that the chromatographic separation in both sorbent/solvent systems is not influenced by molar mass of a sample or by its long chain branching. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Chemically stable hybrid polymer electrolyte membranes prepared by radiation grafting,sulfonation, and silane‐crosslinking techniques

To prepare a crosslinked hybrid polymer electrolyte membrane (PEM) with high chemical stability, a silane monomer, namely p‐styryltrimethoxysilane (StSi), was first grafted to poly(ethylene‐co‐tetrafluoroethylene) (ETFE) film by γ‐ray preirradiation. Hydrolysis‐condensation and sulfonation were then performed on the StSi‐grafted ETFE (StSi‐g‐ETFE) films to give them crosslinks and proton conductibility, respectively. Thus, a crosslinked proton‐conducting hybrid PEM was obtained. The crosslinks introduced by the silane‐condensation have an inorganic ? Si? O? Si? structure, which enhance the chemical and thermal stabilities of the PEM. The effect of the timing of the hydrolysis‐condensation (before or after sulfonation) and the sulfonation method (by chlorosulfonic acid or H₂SO₄) on the properties of the resulting hybrid PEMs such as ion‐exchange capacity, proton conductivity, water uptake, chemical stability, and methanol permeability were investigated to confirm their applicability in fuel cells. We conclude that the properties of the new crosslinked hybrid StSi‐grafted PEMs are superior to divinylbenzene (DVB)‐crosslinked styrene‐grafted membranes. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5559–5567, 2008     

Electron microscopy of high‐pressure crystallized poly(ethylene terephthalate)

The high‐pressure crystallized poly(ethylene terephthalate) samples were investigated with scanning electron microscopy. The striation appearance, which is the most common feature of polymer extended‐chain crystals, was clearly observed. Poly(ethylene terephthalate) extended‐chain crystals with thickness up to 17 m were obtained at high pressure. Fibrous crystals were also formed at high pressure. The fracture behaviors, which affected the exposure of the striations, were also discussed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1612–1616, 2000     

A new high‐pressure strontium germanate,SrGe2O5

The Sr–Ge–O system has an earth‐scientific importance as a potentially good low‐pressure analog of the Ca–Si–O system, one of the major components in the constituent minerals of the Earth's crust and mantle. However, it is one of the germanate systems that has not yet been fully examined in the phase relations and structural properties. The recent findings that the SrGeO₃ high‐pressure perovskite phase is the first Ge‐based transparent electronic conductor make the Sr–Ge–O system interesting in the field of materials science. In the present study, we have revealed the existence of a new high‐pressure strontium germanate, SrGe₂O₅. Single crystals of this compound crystallized as a co‐existent phase with SrGeO₃ perovskite single crystals in the sample recovered in the compression experiment of SrGeO₃ pseudowollastonite conducted at 6 GPa and 1223 K. The crystal structure consists of germanium–oxygen framework layers stacked along [001], with Sr atoms located at the 12‐coordinated cuboctahedral site; the layers are formed by the corner linkages between GeO₆ octahedra and between GeO₆ octahedra and GeO₄ tetrahedra. The present SrGe₂O₅ is thus isostructural with the high‐pressure phases of SrSi₂O₅ and BaGe₂O₅. Comparison of these three compounds leads to the conclusion that the structural responses of the GeO₆ and GeO₄ polyhedra to cation substitution at the Sr site are much less than that of the SrO₁₂ cuboctahedron to cation substitution at the Ge sites. Such a difference in the structural response is closely related to the bonding nature.     

Competitive hydrogen bonding and self‐assembly in poly(2‐vinyl pyridine)‐block‐poly(methyl methacrylate)/poly(hydroxyether of bisphenol A) blends

Blends of poly(2‐vinyl pyridine)‐block‐poly(methyl methacrylate) (P2VP‐b‐PMMA) and poly(hydroxyether of bisphenol A) (phenoxy) were prepared by solvent casting from chloroform solution. The specific interactions, phase behavior and nanostructure morphologies of these blends were investigated by Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), dynamic light scattering (DLS), atomic force microscopy (AFM), and transmission electron microscopy (TEM). In this block copolymer/homopolymer blend system, it is established that competitive hydrogen bonding exists as both blocks of the P2VP‐b‐PMMA are capable of forming intermolecular hydrogen bonds with phenoxy. It was observed that the interaction between phenoxy and P2VP is stronger than that between phenoxy and PMMA. This imbalance in the intermolecular interactions and the repulsions between the two blocks of the diblock copolymer lead to a variety of phase morphologies. At low phenoxy concentration, spherical micelles are observed. As the concentration increases, PMMA begins to interact with phenoxy, leading to the changes of morphology from spherical to wormlike micelles and finally forms a homogenous system. A model is proposed to describe the self‐assembled nanostructures of the P2VP‐b‐PMMA/phenoxy blends, and the competitive hydrogen bonding is responsible for the morphological changes. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1894–1905, 2009